Search
dr hab. inż. Mariusz Deja
Employment
- Dean at Faculty of Mechanical Engineering and Ship Technology
- Associate professor at Institute of Manufacturing and Materials Technology
Publications
Filters
total: 88
Catalog Publications
Year 2024
-
Application of 3D scanning and computer simulation techniques to assess the shape accuracy of welded components
PublicationWhile traditional measurement methods prove to be insufficient when facing more complex shapes and intricate challenges, increasingly efficient solutions are emerging in their place. 3D scanners in particular exhibit versatility. They clearly represent a useful tool in many fields with diverse requirements; thus, it is advisable to explore further areas of their potential applications, e.g., in quality control or reverse engineering....
-
Simulation-Based Approach to a More Efficient Handling Strategy for a Container Terminal Storage Yard: Case Study of the Baltic Hub Container Terminal
PublicationThe primary objective of this research was to implement a more efficient handling strategy in the container terminal storage yard at the Baltic Hub Container Terminal (BHCT). Following an analysis of the current logistics system associated with starboard-side mooring, an attempt was made to shift the mooring to the port side. Two routing strategies corresponding to the analysed mooring operations were tested using a developed...
-
The study on the appearance of deformation defects in the yacht lamination process using an AI algorithm and expert knowledge
PublicationThis article describes the application of the A-priori algorithm for defining the rule-based relationships between individual defects caused during the lamination process, affecting the deformation defect of the yacht shell. The data from 542 yachts were collected and evaluated. For the proper development of the algorithm, a technological process of the yacht lamination supported by expert decisions was described. The laminating...
Year 2023
-
Multi-response optimization on the effect of wet and eco-friendly cryogenic turning of D2 steel using Taguchi-based grey relational analysis
PublicationMaterial removal processes, including turning and milling, are still commonly used operations for manufacturing most of mechanical components in modern industry. Apart from the cutting parameters, the cooling method has the great impact on the technological efects and, above all, on the environmental friendliness of production. In this study, multi-response optimization on the efect of wet and cryogenic machining is performed during...
-
Project-Based Collaborative Research and Training Roadmap for Manufacturing Based on Industry 4.0
PublicationThe importance of the economy being up to date with the latest developments, such as Industry 4.0, is more evident than ever before. Successful implementation of Industry 4.0 principles requires close cooperation of industry and state authorities with universities. A paradigm of such cooperation is described in this paper stemming from university partners with partly overlapping and partly complementary areas of expertise in manufacturing....
-
Reduction of exceeding the guaranteed service time for external trucks at the DCT Gdańsk container terminal using a six sigma framework
PublicationPurpose The purpose of this research was to investigate ways to reduce the average amount of exceeded guaranteed service time for external trucks at Deepwater Container Terminal Gdańsk Sp z o.o. (DCT Gdańsk) via dosing the gate activities, in particular IN-Gate entry process of trucks carrying import/export/transit containers. Design/methodology/approach A Six Sigma methodology with the DMAIC methods along with the SIPOC chart,...
-
The use of Preston equation to determine material removal during lap-grinding with electroplated CBN tools
PublicationGrinding executed in a lapping configuration is an alternative finishing process benefiting from both grinding and free-abrasive machining, while minimizing the heat effect impact. Electroplated tools can be effectively used in different abrasive processes, including high-speed grinding, however, the assessment of machining performance over time is a key factor in their correct use to achieve satisfactory technological results....
Year 2022
-
A Strategy for Managing the Operation of Technical Infrastructure Based on the Analysis of “Bad Actors”—A Case Study of LOTOS Group S.A.
PublicationThe article covers issues related to the selection of a management strategy for the operation of technical infrastructure. It contains the approaches, methodology and a general model of the system of operation of the Maintenance Services of the LOTOS Group production company, which is an example of a large oil concern. Nowadays, an increasing aspect is put on the efficiency of individual repair processes, as well as the operation...
-
Case Study on the Use of Unmanned Aerial Vehicles for the Maintenance of Ocean Engineering Facilities
PublicationThe article presents the concept of using innovative unmanned aerial vehicles (UAVs), including autonomous UAV-I for inspection activities, auxiliary and transport works in the processes of servicing large-scale ocean engineering structures in the offshore part of the sea. The proposed areas of application of UAV-I devices and key technologies determining the possibility of using these vehicles in difficult operating conditions...
-
Development of Technical Creativity Featuring Modified TRIZ-AM Inventive Principle to Support Design for Additive Manufacturing
Publicationhe design for additive manufacturing (DFAM) processing was introduced to fully utilise the design freedom provided by additive manufacturing (AM). Consequently, appropriate design methodologies have become essential for this technology. Recently, many studies have identified the importance of DFAM method utilisation to produce AM parts, and TRIZ is a strategy used to formalise design methodologies....
-
Method of Monitoring of the Grinding Process with Lapping Kinematics Using Audible Sound Analysis
PublicationUtilising microphones as audible sound sensors for monitoring a single-side grinding process with lapping kinematics is presented in the paper. The audible sound generated during grinding depended on the cutting properties of electroplated tools with D107 diamond grains and different thicknesses of the nickel bond. The tool wear affected the obtained technological effects such as material removal rate and the surface roughness...
Year 2021
-
A Pilot Study on Machining Difficult-to-Cut Materials with the Use of Tools Fabricated by SLS Technology
PublicationThe growing use of contemporary materials in various industrial sectors, such as aerospace, automotive, as well as the oil and gas industry, requires appropriate machining methods and tools. Currently, apart from the necessity to obtain high-dimensional and shape accuracy, the efficiency and economic aspects of the selected manufacturing process are equally important, especially when difficult-to-cut materials, such as hard and...
-
A pilot study to assess manufacturing processes using selected point measures of vibroacoustic signals generated on a multitasking machine
PublicationThe article presents the method for the evaluation of selected manufacturing processes using the analysis of vibration and sound signals. This method is based on the use of sensors installed outside the machining zone, allowing to be used quickly and reliably in real production conditions. The article contains a developed measurement methodology based on the specific location of microphones and vibration transducers mounted on...
-
Applications of Additively Manufactured Tools in Abrasive Machining—A Literature Review
PublicationHigh requirements imposed by the competitive industrial environment determine the development directions of applied manufacturing methods. 3D printing technology, also known as additive manufacturing (AM), currently being one of the most dynamically developing production methods, is increasingly used in many different areas of industry. Nowadays, apart from the possibility of making prototypes of future products, AM is also used...
-
Automation of the Road Gate Operations Process at the Container Terminal—A Case Study of DCT Gdańsk SA
PublicationThe future increased terminal capacity will result in more container movement through the road complex and rail siding, which are one of the most critical areas (potential bottlenecks) in the container terminal. Truck turnaround time is one of the major factors that customers take into account while deciding how many container volumes they will handle through the container terminal. To enable to optimize increased traffic with...
-
Planning optimised multi-tasking operations under the capability for parallel machining
PublicationThe advent of advanced multi-tasking machines (MTMs) in the metalworking industry has provided the opportunity for more efficient parallel machining as compared to traditional sequential processing. It entailed the need for developing appropriate reasoning schemes for efficient process planning to take advantage of machining capabilities inherent in these machines. This paper addresses an adequate methodical approach for a non-linear...
-
Thermal and technological aspects of double face grinding of C45 carbon steel
PublicationIn grinding, the contact zone temperature is a decisive factor influencing the achievable surface quality and the grinding tool wear. In contrast to other grinding processes, only few information regarding double face grinding with planetary kinematics when processing steel is known up to date. Since the successive substitution of in-dustrial double-sided lapping processes by double-sided grinding, it has become necessary to the...
Year 2020
-
A pilot study to assess an in-process inspection method for small diameter holes produced by Direct Metal Laser Sintering
PublicationPurpose The purpose of this research is to evaluate the geometric quality of small diameter holes in parts printed by DMLS technology. An in-process optical inspection method is proposed and assessed during a pilot study. The influence of the theoretical hole diameter assumed in a CAD system and the sample thickness (hole length) on the hole clearance was analysed. Design/methodology/approach The samples made of two different...
-
Application of 3D printing metal powder technology in the manufacture of components with complex geometries
PublicationThe possibilities of using 3D printing powder technologies for making objects with complex geometries were presented. For this purpose, selected examples of elements with different geometries were used, which were built using metal powder methods – DMLS (direct metal laser sintering) / SLM (selective laser melting). Simultaneously, the indicated elements concern those areas of industry where 3D printing technology has been widely...
-
Effect of pine impregnation and feed speed on sound level and cutting power in wood sawing
PublicationThe sound levels along with the cutting power registered during the sawing process of the impregnated and non-impregnated pine wood at two feed speeds are shown and compared in this paper. Statistically significant differences in the acoustic signals occurred at the lower feed rate. The differences became smaller with an increase in the feed speed. In contrast to the sound signal, the differences...
-
Innovative rehabilitation lifts – mechanics in medical devices
PublicationMechanical devices are now widely used in physiotherapy and other rehabilitation processes. Particular importance is attached to devices enabling easy and effective transport of disabled people. The article presents innovative designs of rehabilitation lifts offered by the Polish manufacturer of lifts and medical accessories, LeviCare company. Moreover, the main assumptions of the research and development project implemented by...
-
MULTI-CRITERIA COMPARATIVE ANALYSIS OF THE USE OF SUBTRACTIVE AND ADDITIVE TECHNOLOGIES IN THE MANUFACTURING OF OFFSHORE MACHINERY COMPONENTS
PublicationThe dynamic development of additive manufacturing technologies, especially over the last few years, has increased the range of possible industrial applications of 3D printed elements. This is a consequence of the distinct advantages of additive techniques, which include the possibility of improving the mechanical strength of products and shortening lead times. Offshore industry is one of these promising areas for the application...
-
Opportunities and challenges for exploiting drones in agile manufacturing systems
PublicationDrones have become an advanced supply chain implementation instrument, especially in connecting warehouses to outlet points or even individual customers. However, their potential application in an intra-logistics framework has not been studied, let alone explored so far. Modeling and simulations in virtual environments can help explore and evaluate the opportunities for practical and profitable applications of drones in manufacturing...
-
The Influence of the Depth of Cut in Single-Pass Grinding on the Microstructure and Properties of the C45 Steel Surface Layer
PublicationThe paper contains the results of a metallographic examination and nanoindentation test conducted for the medium carbon structural steel with low content of Mn, Si, Cu, Cr, and Ni after its grinding to a depth ranging from 2 μm to 20 μm, at constant cutting speed (peripheral speed) of vs = 25 ms−1 and constant feed rate of vft = 1 m/min. Applied grinding parameters did not cause the surface layer hardening, which could generate...
-
Wear of electroplated diamond tools in lap-grinding of Al2O3 ceramic materials
PublicationCurrent development of modern products, together with ever-increasing demands for their operation and usage, necessitate the search for new processing methods. Abrasive machining is widely used in many industrial areas, especially for processing difficult-to-machine materials such as advanced ceramics. Grinding with lapping kinematics, also called lap-grinding, is still one of the innovative methods of abrasive processing being...
Year 2019
-
Application of Reverse Engineering Technology in Part Design for Shipbuilding Industry
PublicationIn the shipbuilding industry, it is difficult to create CAD models of existing or prototype parts, especially with many freeform surfaces. The paper presents the creation of the CAD 3D model of a shipbuilding component with the application of the reverse engineering technology. Based on the data obtained from the digitization process, the component is reconstructed in point cloud processing programs and the CAD model is created....
-
Kształtowanie właściwości warstwy wierzchniej podczas szlifowania
PublicationW artykule scharakteryzowano szlifowanie powierzchni płaskich połączone ze zmianami właściwości warstwy wierzchniej, zwłaszcza poprzez jej zahartowanie. Omówiono problemy związane z tzw. technologią grind-hardening. Dodatkowo przedstawiono badania, w których po procesie szlifowania uzyskano lepsze właściwości elementu obrabianego wskutek odkształcenia plastycznego.
-
Thermal and technological aspects of double face grinding of Al2O3 ceramic materials
PublicationDouble face grinding with planetary kinematics is a process to manufacture workpieces with plan parallel functional surfaces, such as bearing rings or sealing shims. In order to increase the economic efficiency of this process, it has to be advanced permanently. The temperature in the contact zone of most grinding processes has a huge influence on the process efficiency and the workpiece qualities. In contrast to most grinding...
Year 2018
-
Application of Rapid Prototyping technology in the manufacturing of turbine blade with small diameter holes
PublicationThe article presents the possibilities of using Rapid Prototyping (RP) technology in the manufacturing of turbine blades with small diameter holes. The object under investigation was gas turbine blade with small diameter cooling holes and holes for generating longitudinal vortices. A turbine blade model was produced by means of Direct Metal Laser Sintering (DMLS) technology and subsequently validated in terms of detection and accuracy...
-
Influence of parameters of deep grinding on nanohardness and surface roughness of C45 steel
PublicationPrzedstawiono wyniki badań wpływu głębokości współbieżnego szlifowania powierzchni płaskich na chropowatość i nanotwardość warstwy wierzchniej stali C45 o strukturze ferrytyczno-perlitycznej i średniej wielkości ziarna 20 μm. Dla wszystkich wartości głębokości szlifowania uzyskano znaczny wzrost twardości warstwy wierzchniej przedmiotu obrabianego.
-
Machining process sequencing and machine assignment in generative feature-based CAPP for mill-turn parts
PublicationProcess selection and sequencing, as one of the most complex issues when evaluated from a mathematical point of view and crucial in CAPP, still attract research attention. For the current trend of intelligent manufacturing, machining features (MFs) are the information carriers for workpiece geometry and topology representation. They are basically derived from CAD models and are used by downstream engineering applications. A feature-based...
-
Monitoring of single-side lap grinding with electroplated tools
PublicationThe results presented in the paper show that utilising microphones as audible sound sensors is a suitable approach for monitoring a single-side lap grinding process due to the low levels of noise generated by the drives of a machine tool. The results confirm that sound signal analysis is a feasible and relatively simple method to monitor a lap grinding process with the use of an audible sound sensor. Proposed method can be used...
-
Wpływ parametrów szlifowania wgłębnego na nanotwardość i chropowatość powierzchni stali C45
PublicationW artykule przedstawiono wyniki badań wpływu głębo-kości współbieżnego szlifowania powierzchni płaskich na chropowatość i nanotwardość warstwy wierzchniej stali C45 o strukturze ferrytyczno-perlitycznej i średniej wielkości ziarna 20 µm. Dla wszystkich wartości głębo-kości szlifowania uzyskano znaczny wzrost twardości warstwy wierzchniej przedmiotu obrabianego
Year 2017
-
Analiza efektywności programowanych strategii frezowania złożonych kieszeni
PublicationPrzedstawiono metodę doboru parametrów technologicznych w programowanych strategiach frezowania złożonych kieszeni z wykorzystaniem określonego zestawu narzędziowego. Przeanalizowano wpływ osiowej i promieniowej głębokości skrawania na czas maszynowy realizowanej operacji, co pozwoliło na dobór tych wartości pod kątem maksymalizacji efektywności czasowej wybranej sekwencji narzędziowej.
-
Analiza efektywności programowanych strategii frezowania złożonych kieszeni
PublicationPrzedstawiono metodę doboru parametrów technologicznych w programowanych strategiach frezowania złożonych kieszeni z wykorzystaniem określonego zestawu narzędziowego. Przeanalizowano wpływ osiowej i promieniowej głębokości skrawania na czas maszynowy realizowanej operacji, co pozwoliło na dobór tych wartości pod kątem maksymalizacji efektywności czasowej wybranej sekwencji narzędziowej.
-
Comparative Study of Machining Technology Selection to Manufacture Large-Size Components of Offshore Constructions
PublicationThe focus of this paper is on process planning for large parts manufacture in systems of definite process capabilities, involving the use of multi-axis machining centres. The analysis of machining heavy mechanical components used in off-shore constructions has been carried out. Setup concepts applied and operation sequences determined in related process plans underwent studies. The paper presents in particular a reasoning approach...
-
Simulation studies into quayside transport and storage yard operations in container terminals
PublicationThe focus of the paper is on quayside transport and storage yard operations in the sea container terminals. Developed algorithms for solving the issues of load handling and storage space allocation have been applied in the frame of adopted simulation model. The criteria chosen for decision making involved the total makespan of vessel unloading and the utilisation levels of the transportation trucks. Recommendations for unloading...
-
Wpływ parametrów szlifowania na chropowatość powierzchni stali 1.0562 w stanie zmiękczonym
PublicationPrzedstawiono wyniki badań procesu szlifowania elementów konstrukcyjnych ze stali stopowej 1.0562 w stanie zmiękczonym. Przeanalizowano wpływ głębokości szlifowania ae i prędkości posuwu wzdłużnego przedmiotu vft na chropowatość powierzchni. Zaprezentowano wartości parametrów chropowatości Ra, Rz i Rt możliwe do uzyskania w przyjętych warunkach badań.
-
Wpływ parametrów szlifowania na chropowatość powierzchni stali 10562 w stanie zmiękczonym
PublicationW artykule przedstawiono wyniki badań procesu szlifo-wania elementów konstrukcyjnych wykonanych ze stali stopowej 1.0562 w stanie zmiękczonym. W badaniach analizowano wpływ głębokości szlifowania ae i prędkości posuwu wzdłużnego przedmiotu vft na chropowatość po-wierzchni. Przedstawiono wartości parametrów chropowatości Ra, Rz i Rt możliwe do uzyskania dla zastosowanych warunków badań.
Year 2016
-
Projektowanie strategii frezowania złożonych kieszeni w komponentach mechanicznych
PublicationPrzedstawiono metody wyznaczania optymalnych sekwencji narzędziowych w projektowaniu strategii frezowania złożonych kieszeni przy wykorzystaniu określonego zestawu narzędziowego. W doborze sekwencji dopuszczalnych uwzględniano eliminację sekwencji nieefektywnych. Alternatywne sekwencje narzędziowe modelowano w postaci ważonych grafów acyklicznych dla generowanych wariantów ścieżek kolejnych narzędzi, dokonując ich oceny kosztowej.
-
Szlifowanie jednostronne ściernicami o spoiwie niklowym z ziarnami z regularnego azotku boru
PublicationPrzedstawiono wyniki badań eksperymentalnych szlifowania jednostronnego stali stopowej 40H i ceramiki beztlenkowej SSiC z zastosowaniem ściernic o spoiwie niklowym z ziarnami z regularnego azotku boru B107 i B64. Zaprezentowano uzyskane wartości liniowego ubytku materiałowego oraz parametru Ra chropowatości powierzchni. Scharakteryzowano ogólnie zużycie czynnej powierzchni ściernicy.
-
Szlifowanie jednostronne ściernicami o spoiwie niklowym z ziarnami z regularnego azotku boru
PublicationPrzedstawiono wyniki badań eksperymentalnych szlifowania jednostronnego stali stopowej 40H i ceramiki beztlenkowej SSiC z zastosowaniem ściernic o spoiwie niklowym z ziarnami z regularnego azotku boru B107 i B64. Zaprezentowano uzyskane wartości liniowego ubytku materiałowego oraz parametru Ra chropowatości powierzchni. Scharakteryzowano ogólnie zużycie czynnej powierzchni ściernicy.
-
Wewnętrzny system zapewnienia jakości kształcenia na wydziałach PG
PublicationW artykule przedstawiono podstawowe informacje o Wewnętrznym Systemie Zapewnienia Jakości Kształcenia (WSZJK) i zasadach jego funkcjonowania na wydziałach Politechniki Gdańskiej.
-
Zastosowanie programowania parametrycznego w planowaniu operacji obróbki elementów o powtarzalnej geometrii
PublicationPorównywano zastosowania dostępnych technik programowania obróbki numerycznej przedmiotów o powtarzających się elementach konstrukcji. Analizowano możliwości stosowania programowania parametrycznego w trybie programowania zorientowanego warsztatowo oraz pracy w środowisku systemu klasy CAM. Zwrócono uwagę na przejrzystość tworzonego programu w aspekcie możliwości jego edycji i korekty składni, formy zapisu programu w pamięci obrabiarki...
-
Zastosowanie programowania parametrycznego w planowaniu operacji obróbki elementów o powtarzalnej geometrii
PublicationPorównywano zastosowania dostępnych technik programowania obróbki numerycznej przedmiotów o powtarzających się elementach konstrukcji. Analizowano możliwości stosowania programowania parametrycznego w trybie programowania zorientowanego warsztatowo oraz pracy w środowisku systemu klasy CAM. Zwrócono uwagę na przejrzystość tworzonego programu w aspekcie możliwości jego edycji i korekty składni, formy zapisu programu w pamięci obrabiarki...
Year 2015
-
Developments in manufacturing engineering and machining process planning
PublicationCurrent research conducted in the Department of Manufacturing Engineering and Automation is presented in the paper. This includes: abrasive cutting off, grinding with lapping kinematics, rapid prototyping and machining procrss planning. Experimental results and computer simulation are presented and analysed.
-
Microgrinding with single-disk lapping kinematics.
PublicationGrinding operations are carried out with a variety of tool-workpiece configurations. The selection of a grinding process for a particular application depends on part shape, part size, ease of fixture, requirements concerning the acceptable shape errors. It is evident that lapping is very effective in eliminating the waviness while surface grinding is not. Dual disk machines for the double face grinding with planetary kinematics...
-
Szlifowanie jednostronne z wykorzystaniem ściernic o spoiwie galwanicznym
PublicationW referacie przedstawiono wyniki badań eksperymentalnych szlifowania jednostronnego ceramiki tlenkowej Al2O3 z zastosowaniem ściernic o spoiwie galwanicznym z ziarnami diamentowymi D107 i D64. Prototypowe ściernice charakteryzowały się różną wysokością warstwy spoiwa niklowego wpływającą na głębokość i trwałość utwierdzenia ziaren ściernych. Ściernice wykonano dla trzech warto- ści współczynnika hs wysokości warstwy spoiwa w stosunku...
Year 2014
-
Generative Process Planning with Reasoning based on Geometrical Product Specification
PublicationThe focus of this paper is on computer aided process planning for parts manufacture in systems of definite process capabilities, involving the use of multi-axis machining centers for parts shaping and grinding machines for finishing. It presents in particular a decision making scheme for setup determination as a part of generative process planning. The planning procedurę consists of two stages. The first stage is associated with...
-
Metody pomiaru temperatury przedmiotów i ściernicy w procesie szlifowania jednotarczowego
PublicationW referacie przedstawiono metody pomiaru temperatury w szlifowaniu jednotarczowym z kinematyką docierania. W opracowanym rozwiązaniu wykorzystano małe, zasilane bateryjnie przyrządy rejestrujące temperaturę, tzw. logery pastylkowe o symbolu DS1922L produkcji firmy Dallas Semiconductor. Do pomiarów temperatury wykorzystano również kamerę termowizyjną. Zastosowanie czujników termoelektrycznych pozwoliło zarejestrować temperaturę...
seen 4503 times