prof. dr hab. inż. Jerzy Łabanowski
Employment
- Head of Section at Zakład Technologii Materiałów Konstrukcyjnych i Spajania
- Professor at Institute of Manufacturing and Materials Technology
Publications
Filters
total: 166
Catalog Publications
Year 2021
-
ADVANCES IN MATERIALS SCIENCE EDITORIAL ON THE JOURNAL'S 20th ANNIVERSARY
PublicationEditorial on the occasion of the 20th anniversary of Advances in Materials Science journal.
Year 2019
-
Advantages of the Application of the Temper Bead Welding Technique During Wet Welding
PublicationThermo-mechanically rolled S460ML steel was chosen for welding in underwater wet welding conditions by covered electrodes. The main aim of this study was to check the weldability for fillet welds in a water environment by controlled thermal severity (CTS) tests and to check the influence of temper bead welding (TBW) on the weldability of the investigated steel. Non-destructive and destructive tests showed that S460ML steel has...
-
Effect of the welding environment and storage time of electrodes on the diffusible hydrogen content in deposited metal
PublicationIn the study the glycerin displacement method was used for determination of diffusible hydrogen content in deposited metal. Specimens were welded in the air and in the water with covered rutile electrodes. The first part of the specimens was made immediately after opening the package of the electrodes. The electrodes were then stored in opened packages in laboratory conditions that allowed for contact with the air for three years....
Year 2015
-
An experimental study of high-hydrogen welding processes
PublicationThis paper presents investigation results of determination of the diffusible hydrogen content in deposited metal obtained by means of two most often used methods-the glycerin method and the mercury method. Relation has been defined between results of those methods in the area characteristic of low-hydrogen as well as high-hydrogen welding processes. Relations available in the literature do not include the diffusible hydrogen content...
-
Cold Cracking Of Underwater Wet Welded S355G10+N High Strength Steel
PublicationWater as the welding environment determines some essential problems influencing steel weldability. Underwater welding of high strength steel joints causes increase susceptibility to cold cracking, which is an effect of much faster heat transfer from the weld area and presence of diffusible hydrogen causing increased metal fragility. The paper evaluates the susceptibility to cold cracking of the high strength S355G10+N steel used,...
Year 2005
-
Analiza zależności zmian składu chemicznego faz mosiądzu odlewniczego od grubości odlewu
PublicationPrzedstawiono wyniki analizy składu chemicznego faz mosiądzu odlewniczego MM55 dla różnych grubości odlewu. Przeanalizowano zależności pomiędzy grubością odlewu i składem chemicznym faz.
-
Assessment of reformer tubes degradation during longterm service at elevated temperatures
Publication -
Assessment of structural changes in IN-519 cast steel reformer tubes.
PublicationPrzedstawiono zmiany struktury rur katalitycznych ze staliwa austenitycznego IN-519 po długotrwałej eksploatacji w reformerze metanu.
Year 2017
-
Analysis of features of stainless steels in dissimilar welded joints in chloride inducted corrosion
PublicationStainless steels of femtic-austenitic microstructure that means the duplex Cr-Ni-Mo steels, in comparison with austenitic steel includes less expensive nickel and has much better mechanical properties with good formability and corrosion resistance, even in environments containing chloride ions. Similar share of high chromium ferrite and austenite, which is characterized by high ductility, determines that the duplex steels have...
-
Badania śrub kominów 250, 120, 270, 9800
PublicationPrzedmiotem pracy było wykonanie badań pękniętych śrub komina 250 oraz ustalanie przyczyn ich uszkodzenia. Przedmiotem drugiego zadania było wykonanie badań weryfikacyjnych śrub pobranych z połączeń kołnierzowych kominów 120, 270 i 9800.
-
Corrosion behavior of hydrogen charged super duplex stainless steel welded joints
PublicationThe electrochemical behavior of the weld metal, heat-affected zone (HAZ), and base material of super duplex stainless steel (SDSS) welded joints, made with the application of flux-cored arc welding (FCAW) and submerged arc welding (SAW), were investigated with the use of metallographic examinations (optical microscopy and scanning electron microscopy), potentiodynamic polarization measurements and total hydrogen content determination...
-
ENVIRONMENTAL DEGRADATION OF DISSIMILAR AUSTENITIC 316L AND DUPLEX 2205 STAINLESS STEELS WELDED JOINTS
PublicationThe paper describes structure and properties of dissimilar stainless steels welded joints between duplex 2205 and austenitic 316L steels. Investigations were focused on environmentally assisted cracking of welded joints. The susceptibility to stress corrosion cracking (SCC) and hydrogen embrittlement was determined in slow strain rate tests (SSRT) with the strain rate of 2.2 × 10–6 s–1. Chloride-inducted SCC was determined in the...
Year 2018
-
Application of Multivariate Analysis Methods in Welding Engineering
PublicationPhenomena and processes taking place during welding are usually very complex and, for this reason, should be described using multivariate methods. The article discusses the methodological basis and selected application areas as regards the solving of welding problems using statistical multivariate methods. In addition, the article presents exemplary applications of the design of experiment, multiple regression analysis, cluster...
-
Badania spawalności stali S460N w środowisku wodnym z wykorzystaniem próby Tekken
PublicationSpawanie w środowisku wodnym niesie ze sobą wiele problemów, wśród których najważniejszym jest skłonność stali do powstawania pęknięć zimnych. O ile w przypadku spawania na powietrzu istnieje wiele metod zapobiegania tym pęknięciom, o tyle pod wodą zastosowanie tych metod jest ograniczone. Z tego powodu konieczne jest określenie skłonności danego materiału do pękania zimnego. W pracy oceniono spawalność drobnoziarnistej...
-
COLD CRACKING OF S460N STEEL WELDED IN WATER ENVIRONMENT
PublicationThis paper shows results of weldability testing of fine-grained high -strength low- alloy S460N steel welded in water environment by covered electrodes. The tests were carried out by using the CTS test specimens with fillet welds. Four specimens were welded under water and one specimen in air. Welded joints were subjected to non-destructive visual and penetration tests. The accepted joints were then subjected to macroscopic and...
-
Effect of the Post-Weld Surface Condition on the Corrosion Resistance of Austenitic Stainless Steel AISI 304
PublicationSurfaces of welded elements made of corrosion-resistant (stainless) steels develop temper colours. The removal of thickened oxide layers off steels exposed to temperatures below 300°C is necessary and entails the restoring of high corrosion resistance of the stainless steel. The article presents tests concerned with the effect of a method applied to remove post-weld temper on the corrosion resistance of austenitic stainless steel...
-
Ekspertyza przyczyn pęknięcia iglicy rozjazdu kolejowego nr 243
PublicationCelem badań było ustalenie przyczyny pęknięcia iglicy rozjazdu kolejowego
-
Ekspertyza przyczyn pęknięcia rurociągu w instalacji 016-P1365
PublicationWykonano badania przyczyn pęknięcia złącza wzmocnienia i rurociągu w instalacji 016-P1365. Ustalono prawdopodobną przyczynę pękania.
Year 2016
-
As causas do trincamento a frio de um ação submetido a soldagem subaquática
PublicationA soldagem subaquàtica usada na confeccao de juntas de acos de alta resistencia aumenta a sua susceptibilidade ao trincamento a frio, um efeito decorrente da transferencia de calor muito mais rapida a partir da area de soldagem e da presenca de hidrogenio difusivel, o que causa aumento da fragilidade do metal. Este trabalho avalia esta propensao ao trincamento a frio do aco S355G10+N usado na construcao de estrururas hidrotecnicas...
-
Badania skłonności do pękania zimnego złączy doczołowych ze stali typu dupleks 2205 wykonanych w środowisku wodnym
PublicationW pracy zbadano skłonność stali dupleks 2205 do tworzenia pęknięć zimnych. Wykonano technologiczne próby Tekken w warunkach podwodnych metodą mokrą z wykorzystaniem elektrod otulonych. Przedstawiono wyniki badań twardości, badań metalograficzny makro i mikroskopowych oraz badań zawartości ferrytu.
-
Effect of Linear Energy and Microstructure on the Content of Residual Hydrogen in Welded Joints made of Superduplex Steels
PublicationThe article presents tests concerning the content of retained hydrogen present in FCAW and SAW welded joints made of superduplex steel. The use of various welding technologies resulted in the obtainment of welds having different microstructures and ferrite contents. Measurements of retained hydrogen present in joints (performed using the complete combustion method) revealed various contents of hydrogen in the base material and...
-
Effect of long term service at elevated temperatures on mechanical properties of Manaurite XM reformer tubes
PublicationMicrostructure transformations occur in the Manaurite XM cast steel tubes during long-term operation in the reformer furnace were revealed and described. The rela tionship between mechanical properties, an increase of internal diameter of the tube and microstructure degradation is discussed. Static tensile test was performed on two types of samples with different shapes. It has been shown differences in the results of tests...
Year 2008
-
Assessment of evaporator tubes corrosion in low-emission steam boilers
PublicationW artykule przedstawiono wyniki badań rur ekranowych(16Mo3) kotła niskoemisyjnego po jednym roku i dwóch latach eksploatacji. Powierzchnie rur pokryte zostały warstwami natryskiwanymi cieplne - pojedynczą ze stopu 70%Ni 30%Cr i podwójną Ni-30Cr /Al2O3. Rury bez powłok natryskiwanych wykazywały pocienienie ze względu na działanie korozji siarkowej oraz korozyjnego oddziaływania warstwy stopionych soli. Pojedyncza warstwa 70%Ni 30%Cr...
Year 2006
-
Badania podatności do korozji naprężeniowej spawanych złączy różnoimiennych stali austenitycznej oraz typu duplex
PublicationPrzedstawiono wyniki badań spawanych złączy różnoimiennych wykonanych ze stali austenitycznej gatunku AISI 316L oraz typu duplex 2205. Wykonano 3 płyty próbne za pomocą spawania automatycznego łukiem krytym pod topnikiem. Badania podatności do korozji naprężeniowej złączy wykonano metodą odkształcania z małą prędkością. Próby przeprowadzono w środowisku obojętnym oraz agresywnym (MgCl2).
Year 2012
-
Badania przyczyn uszkodzenia rurki impulsowej
PublicationDokonano oceny przyczyn uszkodzenia rurki impulsowej ze stali nierdzewnej
-
Determination of Failure Causes of a Steam Turbine Casing
PublicationThe paper presents results of research and failure analysis undertaken to determine failure causes of a steam turbine casing. After 130,000 hours of service the crack in a outer shell of the turbine casing was found. The inner shell of the casing was made of cast steel grade G21CrMoV5-7, and the outer shell of grade G20CrMo4-5. Following research were performed in order to determine causes of the casing failure: chemical analysis;...
-
Determining diffusible hydrogen amounts using the mercury method. Welding International
PublicationW artykule przedstawiono szczegółową charakterystykę procedury oznaczania ilości wodoru dyfundującego metodą rtęciową na tle innych metod badawczych i aktualnego stanu wiedzy dotyczącego rozpatrywanego zagadnienia. Omówiono klasyfikację wodoru występującego w złączu spawanym oraz metody oznaczania ilości wodoru dyfundującego w stopiwie ze zwróceniem szczególnej uwagi na metodę rtęciową jako metodę podstawową. Zestawiono zależności...
-
Ekspertyza materiałowa rurociągów ze stali w gatunku AISI 304
PublicationWykonano badania przyczyn uszkodzenia połączeń spawanych rurociągów ze stali AISI304. Sformułowano wnioski mające wyeliminować podobne problemy w przyszłości.
-
Environmental Degradation of Engineering Materials & Materials Engineering and Technologies
Publication
Year 2014
-
Badania przyczyn uszkodzenia U-rurki wymiennika ciepła instalacji 150-E06
PublicationWykonano kompleksowe badania przyczyn uszkodzenia U-rurki wymiennika ciepła wykonanej ze stali A213 T11. Wskazano możliwe przyczyn wystąpienia uszkodzenia.
-
BADANIA ZŁĄCZY SPAWANYCH BIMETALU ZGRZEWANEGO WYBUCHOWO STALI NIESTOPOWEJ SA516 Gr. 60 ZE STOPEM MONEL 400
PublicationW pracy przedstawiono wyniki badań doczołowych złączy spawanych bimetalu typu stal niestopowa SA516 Gr. 60 - monel 400 (SB127 UNS 04400). Badany bimetal został wytworzony poprzez zgrzewanie wybuchowe. Określono własności mechaniczne, rozkład twardości oraz strukturę otrzymanych złączy. Zwrócono uwagę na trudności technologiczne spawania tego rodzaju materiału oraz możliwość generowania niezgodności spawalniczych.
-
Bead-on-plate welding on S235JR steel by underwater local dry chamber process
PublicationThe article presents the results of the effect of parameters of underwater local dry chamber welding on the properties of padding welds. The effect of heat input and the type of shielding gas on the structure and hardness of welds was established. the functions for estimating the maximum hardness of the heat affected zone have been also elaborated.
-
Effect of microstructure on mechanical properties and corrosion resistance of 2205 duplex stainless steel
PublicationThis paper presents results of the research on impact of microstructure of austenitic-ferritic steel of duplex type on its mechanical properties and susceptibility to stress corrosion cracking. As showed, improper processing technologies more and more often used in shipbuilding industry for plates and other half-finished products made of duplex steel may cause significant lowering their properties, which frequently makes their...
-
Effect of microstructure on mechanical properties of BA1055 bronze castings
PublicationThe article presents research results performed on aluminum bronze CuAl10Fe5Ni5 (BA1032) castings used for marine propellers. Metallographic studies were made on light microscope and a scanning electron microscope to assess quantitatively and qualitatively the alloy microstructure. It has been shown that the shape, size and distribution of the iron-rich phase precipitates in bronze microstructure significantly affect its mechanical...
-
Ekspertyza połączeń lutowanych rur miedzianych
PublicationCelem pracy było ustalenie rodzaju lutu zastosowanego do spajania rur miedzianych o średnicy 20 mm, ustalenie technologii lutowania oraz wydanie opinii czy połączenia lutowane gwarantują bezpieczeństwo podczas użytkowania rurociągu w wewnętrznej instalacji gazowej w budownictwie mieszkaniowym
-
Ekspertyza przyczyn korozji złącza spawanego rury ze szwem 129x3,0 mm z instalacji flokulatora
PublicationCelem pracy było ustalenie przyczyn korozji złącza spawanego rury ze szwem 130x3,0 mm z instalacji flokulatora. Instalacja była wykonana ze stali nierdzewnej AISI 316L. Zakres pracy obejmował: wykonanie analizy EDX składu chemicznego spoiny oraz nalotów obecnych na rurociągu, wykonanie badań próbek metalograficznych wraz z określeniem mikrostruktury
Year 2004
-
Badania uszkodzeń rur parownika kotła wodnego.
PublicationW pracy przedstawiono badania uszkodzeń rur parownika kotła wodnego. Stwierdzono uszkodzenia w postaci wżerów wywołanych lokalnymi ogniwami stężeniowymi
Year 2011
-
Certyfikowanie nurków-spawaczy przy spawaniu mokrym pod wodą w warunkach hiperbarycznych
PublicationW artykule omówiono wymagania normy PN-EN ISO 15618-1:2002: Egzamin kwalifikacyjny spawaczy w zakresie spawania podwodnego. Część 1: Spawacze-nurkowie spawający na mokro w warunkach hiperbarycznych. Podano zakresy możliwych do uzyskania zakresów kwalifikacji, wytyczne odnośnie wszystkich zmiennych zasadniczych ujętych w normie oraz przykłady oznaczenia uprawnień nurka-spawacza. Wskazano treści, które należy poddać analizie przy...
Year 2010
-
Charakterystyki naprężeniowe stali x20
PublicationBadano wpływ naprężeń na natężenie efektu Barkhausena w próbkach stali X20 (X20CrMoV12.1) poddanych obróbce cieplnej mającej obniżyć poziom naprężeń wewnętrznych. Trzy serie próbek stali X20 wygrzewano w temperaturach 720 0C, 750 0C i 780 0C przez czas 15, 30, 60, 120 i 240 min. Badano również twardość Vickersa. Wpływ naprężeń na natężenie efektu Barkhausena badano metodą uginania belki. Wygrzewanie w dwóch niższych temperaturach...
-
Corrosion of evaporator tubes in low emission steam boilers
PublicationPurpose of this paper is to reveal the mechanisms of corrosion processes of outer surfaces of low-emission steam boiler evaporator tubes. Examinations were performed to find the reasons of different corrosion susceptibility of tubes situated at combustion chamber on various levels. Examinations were conducted on several segments of 57 x 5.0 mm evaporator tubes made of 16M (16Mo3) steel grade. Segments were taken from level of...
-
Diagnostyka metodą magnetyczną stanu naprężeń w złączu spawanym ze stali dupleks
PublicationStan naprężeń własnych w doczołowych złączach spawanych ze stali dupleks (typ 2205) i stali austenitycznej (typ A316L) zbadano wykorzystując efekt Barkhausena. Badania wykonano dla trzech typów ukosowania spawanych obszarów (1 - kształt Y, 2 - kształt 2Y oraz 3 - kształt I). W przypadku kształtu Y spawanie wykonano z warunkiem limitu energii (przypadek 1a) oraz bez ograniczeń energetycznych (przypadek 1b). Kalibracje naprężeniową...
-
Ekspertyza materiałowa osłon palników generatorów gazów obojętnych
PublicationNa zlecenie firmy PIROMETAL z Gdańska wykonano badania materiałowe osłon palników generatorów gazów obojętnych. Wykonano analizy składu chemicznego 4 próbek pobranych z osłon palników, identyfikację zastosowanych materiałów.Przeprowadzono analizę przydatności zastosowanych stali na osłony palników oraz przedstawiono opinię nt. doboru materiału na osłony palnika w generatorach gazów obojętnych.
-
Eksploatacyjne uszkodzenia stali austenitycznych w urządzeniach energetycznych
PublicationW artykule przedstawiono proces niszczenia stali austenitycznych stosowanych w urządzeniach energetycznych, takich jak wymienniki ciepła czy wytwornice pary, w warunkach korozji lokalnej: wżerowej, podosadowej, naprężeniowej i międzykrystalicznej, ze zwróceniem szczególnej uwagi na połączenia spawane. Analizowano wpływ składu chemicznego stali, mikrostruktury, procesu spawania i środowiska pracy. Przedstawiono wyniki badań metalograficznych...
-
Evaluation of reformer tubes degradation after long term operation
PublicationPurpose of this paper is to show the effect of long-term service at elevated temperatures on microstructural changes of cast steel reformer tubes made of the alloy IN-519 (24%Cr, 24%Ni, Nb). The relationship between mechanical properties and microstructure degradation is discussed. Investigations were performed on five tubes taken from ammonia reformer furnace. Tubes worked at temperature of 880C and 3,2 MPa pressure. The operation...
Year 2007
-
Corrosion resistance of dissimilar austenite and duplex steels welded joints
PublicationW artykule przedstawiono wpływ warunków spawania, a zwłaszcza energii liniowej, na odporność korozyjną złączy różnoimiennych stali austenitycznej 316L i typu duplex 2203. Przedstawiono wyniki testów korozyjnych:korozji wżerowej wg ASTM G48 oraz korozji naprężeniowej badanej w próbach odkształcania z małą pędkością w środowisku roztworu chlorku magnezowego.
Year 2009
-
Effect of chemical composition and microstructure on mechanical properties of BA1055 bronze sand castings.
PublicationW pracy wykazano, że nawet małe zmiany w składzie chemicznym brązu aluminiowego BA1055 mają istotny wpływ na strukturę i właściwości mechaniczne odlewów. Określono wpływ wydzieleń międzymetalicznej fazy κ na właściwości odlewów z brązu BA1055 stosowanego na pędniki okrętowe.
-
Effect of microstructure on impact toughness of duplex and superduplex stainless steels
PublicationW artykule przedstawiono wpływ wyżarzania stali dupleks 2205 i superdupleks 2507 na przemiany strukturalne oraz udarność. Obróbkę cieplną przeprowadzono w zakresie temperatur 500-900C i w czasie 6 - 600 min. Określono i porównano podatność obu stali do zmian właściwości po wyżarzaniu
Year 2023
-
Effect of water salinity on properties of multipass underwater wet manual metal arc welded joints
PublicationThe weldability of steel under the water is limited due to the influence of the environment. Water causes limited visibility, presence of the residual stresses, increasing the cooling rate, and increasing the diffusible hydrogen content in deposited metal, leading to the formation of brittle microstructures in heat-affected zone (HAZ). The paper presents the results of mechanical properties testing of S420G2+M steel welded joints...
-
Effects of Storing Flux-Cored Wires under Various Conditions
PublicationWelding processes involving the use of flux-cored wires are becoming increasingly popular, particularly in shipbuilding as well as in off-shore and civil engineering. The article presents characteristics of the welding process, its areas of application as well as advantages and disadvantages (e.g. necessity of ensuring appropriate conditions for the storage of filler metal wires). The satisfaction of quality-related requirements...
Year 2013
-
Ekspertyza materiałowa rurociągu wody pitnej ze stali gatunku AISI 304
PublicationCelem pracy było ustalenie przyczyny zniszczenia instalacji wodociągowej w budynku. Instalacja była wykonana ze stali nierdzewnej AISI 304. Zakres pracy obejmował: badania makroskopowe uszkodzeń, mikroanalizę EDX produktów korozji występujących na powierzchni wewnętrznej rurociągu, badania metalograficzne uszkodzeń i ocena stanu stali. Analiza doboru stali na elementy instalacji wodociągowej
seen 3305 times