Search
ISSN:
eISSN:
Publisher:
Ministry points: Help
| Year | Points | List |
|---|---|---|
| Year 2024 | 5 | Journal not listed on ministry scored journal list 2024 |
| Year | Points | List |
|---|---|---|
| 2024 | 5 | Journal not listed on ministry scored journal list 2024 |
| 2023 | 5 | Not listed on the ministry scored journals list 2023 |
| 2022 | 5 | Not listed on the ministry scored journals list (2019-2022) |
| 2021 | 5 | Not listed on the ministry scored journals list (2019-2022) |
| 2020 | 5 | Not listed on the ministry scored journals list (2019-2022) |
| 2019 | 5 | Not listed on the ministry scored journals list (2019-2022) |
| 2018 | 6 | B |
| 2017 | 6 | B |
| 2016 | 6 | B |
| 2015 | 6 | B |
| 2014 | 6 | B |
| 2013 | 6 | B |
| 2012 | 7 | B |
| 2011 | 7 | B |
| 2010 | 9 | B |
Model:
Impact Factor:
Publishing policy:
- License
- COPYRIGHT
- Information on publishing policy
- n/a
- Information on the conditions of self-archiving
- n/a
- Is self-archiving allowed by the journal?
- No
- Information on research data policy
- n/a
- Months of embargo
- no embargo
- Additional information
- Type of model: Gratis Open Access (Bronze Open Access).
Papers published in journal
Filters
total: 7
Catalog Journals
Year 2016
-
Integrated production technology of cylindrical surfaces by turning and burnishing
PublicationThe method is based on a combination of previously used two separate operations namely machining and burnishing in a one complex operation implemented on a lathe.In the case of machining shafts and hydraulic cylinders of steel C45 is possible to obtain a surface roughness Ra=0,16 - 0,32 micrometers, dimensional accuracy class 7-8 according to ISO standards, and increase in the hardness of the surface up to 40%.
-
Sliding burnishing technology of holes in hardened steel
PublicationNew technology with sliding burnishing of holes with cylindrical surface, made of hardened steel /60 HRC/, is presented in the paper.After burnishing operation on hole diameter 30 mm in satellite gear wheel the surface roughness parameter Ra=0,02-0,04 micrometers was obtained. The method and results of research as technological conclusion are presented.
Year 2012
-
Simulation research on the tool cycle in automated manufacturing system at selected tool duplication levels
PublicationThe paper presents results of the research concerning impact of applied tool exchange rule on the efficiency of an automated manufacturing system. The research consider the tool duplication levels that constrain realisation of a manufacturing process. Presented study was based on the real industrial system data. The operating of the investigated system of manufacture, including tools necessary for its realisation, was modelled...
Year 2011
-
Impeller pump development using rapid prototyping methods
PublicationMetody szybkiego prototypowania przy wspomaganiu komputerowym projektowania 3D wraz z systemami wspomagania inżynierskiego pozwalają uzyskać wyrób o prognozowanych właściwościach technologicznych i użytkowych.W artykule przedstawiono studium przypadku zastosowania metod szybkiego prototypowania w rozwoju elementów pomp wirowych.
Year 2010
-
Fuzzy logic in controlling flexible manufacturing cell
PublicationIn the present work a controlling method based on fuzzy rule base is proposed. Practical approaches are developed and focused on real time problems related to flexible manufacturing cell. Techniques for design and implementation of fuzzy systems in the framework of control production and quality states are presented. Keywords: controlling, manufacturing system, fuzzy logic, turning, burnishingW artykule przedstawiono propozycję...
-
Studies on the influence of technological variants of finishing machining on flow of parts in flexible manufacturing
PublicationIn the article below the problems of influence of variants of finishing processing on flow of machining parts in flexible manufacturing system were presented. The investigations were carried out the technological processes for piston rods and rams of hydraulic cylinders. There were also presented model variants of technological processes for piston rods finished with the burnishing. In these studies the influence of technological...
Year 2007
-
Experimental studies on specific cutting resistance while cuttingwith narrow-kerf saws
PublicationBadania eksperymentalne właściwego oporu skrawania zostały wymuszone poprzez pojawienie się nowych technologii przecinania za pomocą cienkich pił. W przeprowadzonym eksperymencie wartościami wejściowymi były: rozwarcie całkowite ostrzy (rzaz), posuw na ostrze oraz grubość brzeszczotu piły. W ten sposób, oprócz zmian całkowitego przekroju warstwy skrawanej uwzględniano również wpływ warunków tarcia pomiędzy brzeszczotem piły, ścianami...
seen 968 times