Search
ISSN:
eISSN:
Disciplines
(Field of Science):
- Chemical engineering (Engineering and Technology)
- Civil engineering and transport (Engineering and Technology)
- Materials engineering (Engineering and Technology)
- Mechanical engineering (Engineering and Technology)
- Forestry (Agricultural sciences)
Ministry points: Help
| 2021 | 140 | Ministry Scored Journals List 2019 |
| Year | Points | List |
|---|---|---|
| 2021 | 140 | Ministry Scored Journals List 2019 |
| 2020 | 140 | Ministry Scored Journals List 2019 |
| 2019 | 140 | Ministry Scored Journals List 2019 |
| 2018 | 30 | A |
| 2017 | 30 | A |
| 2016 | 30 | A |
| 2015 | 30 | A |
| 2014 | 30 | A |
| 2013 | 25 | A |
| 2012 | 35 | A |
| 2011 | 35 | A |
| 2010 | 27 | A |
| 2009 | 27 | A |
| 2008 | 27 | A |
Model:
Points CiteScore:
| 2019 | 3.2 |
| Year | Points |
|---|---|
| 2019 | 3.2 |
| 2018 | 2.4 |
| 2017 | 2.4 |
| 2016 | 2.4 |
| 2015 | 2.2 |
| 2014 | 2.2 |
| 2013 | 1.9 |
| 2012 | 1.5 |
| 2011 | 1.5 |
Impact Factor:
Papers published in journal
Filters
total: 8
Catalog Journals
2021
-
Influence of drying mode and feed per tooth rate on the fine dust creation in pine and beech sawing on a mini sash gang saw
PublicationThe experimental results of the study focused on the effect of drying processes of modified air drying and warm air steam mixture drying of pine and beech wood on the size of sawdust particles created in cutting using PRW-15M sash gang saw, are presented in the paper. Particle size analysis of dry sawdust was performed using two methods—sieving method and laser diffraction analysis. The results showed that the drying process did...
-
Insights into modification of lignocellulosic fillers with isophorone diisocyanate: structure, thermal stability and volatile organic compounds emission assessment
PublicationThis study presents an analysis of the structure and properties of different types of lignocellulosic fillers modified by isophorone diisocyanate (IPDI) to provide insights into the possibility of their application to the manufacturing of wood polymer composites (WPCs). Moreover, it deals with the environmental aspects of modified fillers, by assessment of volatile organic compounds (VOCs) emitted during modification, as well as...
2020
-
Cutting model parameters from frame sawing of natural and impregnated Scots pine (Pinus sylvestris L.)
PublicationIn this paper, absolute and density normalized cutting model parameters of natural and impregnated Scots pine (Pinus sylvestris L.) are shown and a method for the calculation of their corresponding material properties in the principal material directions of wood is presented. The parameters were determined from measurements of cutting power on a sash gang saw, and are in detail the fracture toughness and the shear yield strength...
2010
-
A Method of Lathe Checks Measurement; SMOF device and its software
Publication -
Influence of ligno-cellulosic particles on tribological properties of boards
Publication
2009
2006
-
Study washboarding phenomenon in fame sawing machines
PublicationPraca dotyczy zjawiska washboarding cechującego się powstawaniem na piłowanej powierzchni sinusoidalnego profilu w przekroju poprzecznym i wzdłużnym. Wzór ten jest efektem drgań poprzecznych piły. Przedstawiono wyniki analiz teoretycznych oraz badań eksperymentalnych, w których wykazano, że zjawisko w przypadku pilarek ramowych jest efektem drgań wymuszonych brzeszczotu oraz regeneracji powstałej fali pierwotnej.
2002
-
Hybrid dynamically balanced saw frame drive
PublicationW pilarkach ramowych, w których rama piłowa jest napędzana poprzez mechanizm korbowy, generowana przez ramę piłową siła bezwładności oddziaływuje na fundament pilarki oraz na jej układ napędowy. W niniejszym artykule przedstawiono sposób eliminacji tych niekorzystnych zjawisk. Autorzy zaprezentowali dynamicznie wyrównoważony hybrydowy układ napędu ramy piłowej, w którym występuje akumulator energii kinetycznej przyłączony równolegle...
seen 73 times