(Field of Science):
- Biomedical engineering (Engineering and Technology)
- Civil engineering and transport (Engineering and Technology)
- Materials engineering (Engineering and Technology)
- Mechanical engineering (Engineering and Technology)
- Chemical sciences (Natural sciences)
Ministry points: Help
|2021||200||Ministry Scored Journals List 2019|
|2020||200||Ministry Scored Journals List 2019|
|2019||200||Ministry Scored Journals List 2019|
- author's version of the article before the review
- author's version of the article after the review
Status table SHERPA RoMEO
|RoMEO color||Archiving policy|
|Green||can archive pre-prints and post-prints or a version of the publisher|
|Blue||can archive post-prints|
|Yellow||can archive pre-prints|
|White||can not archive any materials|
Papers published in journal
In the present work, the slurry erosion tests were carried out to investigate the influence of heat treatment on slurry erosion process of ferritic X10CrAlSi18 stainless steel using a slurry pot test rig. X10CrAlSi18 stainless steel was tested in as-received condition and after annealing at three different temperatures: 600°C, 800°C and 1000°C. Degradation of materials due to slurry erosion depends on many factors connected with...
Water-lubricated stern tube bearing - experimental and theoretical investigations of thermal effectsPublication
The paper presents research results of thermal phenomena accompanying operation of a water-lubricated stern tube bearing with axial grooves. Experimental tests revealed, that intensity of forced axial flow has strong influence on bush temperature. Numerical simulations focused on investigation of the thermal phenomena under operation of water-lubricated journal bearing showed, that restricted axial flow promotes backflow of the...
Effect of manufacturing errors of the pad sliding surface on the performance of the hydrodynamic thrust bearingPublication
In the present study, investigation of the effect of manufacturing errors on the performance of large tilting pad thrust bearings has been performed, following a CFD-based Thermohydrodynamic analysis of a single pad. A 3D model has been generated, including the pad, the lubricant film and the corresponding part of the collar. The pad has been assumed to be deformed about the pivot point, due to thrust loading. Manufacturing errors...
The aim of this study was to analyse the performance of journal bearings with specially created dimples on the sliding surface and operating under various conditions. The texture was created on the bearing surface that co-acted with the smooth journal; moreover, the variation of the textured surface of the journal mating with the smooth bearing was tested, and the results were compared to those obtained with the standard smooth...
The paper presents results of experimental testing aiming at finding out what effect system of piezo-electric actuators (PZTs)attached to an aerodynamic journal bearing has on the magnitude of shaft's motion within the bearing operating at specified speed and load. The results clearly demonstrate effectiveness of PZTs in mitigating the shaft's motion thus contributing to the increased stability of the bearing. This stabilizing...
Evaluation of apparent Young׳s modulus of the composite polymer layers used as sliding surfaces in hydrodynamic thrust bearingsPublication
Hydrodynamic bearings with a polymer sliding layer are able to operate in severe conditions, mainly due to favorable properties of the polymers. The goal of this research was to evaluate apparent Young׳s modulus of two types of the polymer composite layers used for sliding surfaces in hydrodynamic bearings, as a function of temperature. The Young׳s modulus was evaluated on the basis of compression tests carried out on samples obtained...
Experimental research on water lubricated marine stern tube bearings in conditions of improper lubrication and cooling causing rapid bush wearPublication
Water lubricated bearings are popular in sliding bearings of marine propeller shafts, turbines and pump shafts. Such popularity is partly due to their simple construction which also means a relatively affordable price. In practical experience one may also observe cases of rapid wear or even malfunctions of this bearings, some of which may be caused by insufficient flow of lubricant leading to overheating. The conducted...
One of main problems concerning water-lubricated bearings is their durability. There are known cases of bearings with life time measured in decades, and some, whose refurbishment was necessary just days after start-up. Obtaining stable fluid film friction plays key role in the durability of these bearings. Unfortunately, their load-carrying capacity is limited due to water's low-viscosity. The conducted experimental...
Classical non-contact bearings are already used in a number of specialist applications but there are somespecialist areas where they cannot be used for variety of reasons and acoustic sliding bearings could be an alternative. The paper presents the quest for a configuration of an acoustic journal bearing and shows that the overall shape of the bearing and its geometry are of a vital importance for the load capacity oft he bearing....
Experimental research on water lubricated three layer sliding bearing with lubrication grooves in the upper part of the bush and its comparison with a rubber bearingPublication
composite. Eachofitslayershasanimportantfunction.Speciallypreparedslidingsurfaceensures minimum resistance.Followingrunning-initssmoothnessbecomesveryhighandthebearingmay continue workingunder fluid lubricationregime.NBRlayerensuresbearingelasticity,goodvibration damping propertiesandinsusceptibilitytoshaftaxismisalignment.Theexternalbrasslayermakes fitting thebearingeasier. Experiment resultsoftheconductedresearchwerecomparedwiththoseforarubberbearingof similar...
Polyetheretherketone (PEEK) was investigated using a modified version of the four-ball tester in which the upper forth ball was replaced by a cone in such a way that kinematics of the four-ball configuration were fully preserved. Rotation of the cone enforced orbiting and rolling of the ceramic balls around the polymer cup. The results produced some unexpected peculiarities in the wear of ceramic balls which, in principle, should...
Properties comparison of rubber and three layer PTFE-NBR-bronze water lubricated bearings with lubricating grooves along full bush circumference based on experimental testsPublication
Water lubricated bearings have been in industrial use for well over a century. During the last decade their traditional range has been expanded with new, modern products. Despite that fact, certain solutions continue to employ the standard rubber bearing with lubricating grooves located along entire bush circumference. The work presents experimental research conducted on comparable sliding bearings with lubrication grooves along...
Results of experimental studies concerning the influence of permanent magnetic field on wear of dry sliding contact operating at short stroke and high frequency are presented. It was found that horizontal magnetic field with different orientations relative to the sliding direction is affecting performance of the contact. The increase in frequency of sliding reduces accumulated mass loss and lowers the surface roughness of the wear...
The validity of using the Reynolds equation for compressible squeeze film pressure was tested with computational fluid dynamics (CFD). A squeeze film air bearing was instrumented with pressure sensors and non-contacting displacement probes to provide transient measurements of film thickness and pressure. The film thickness measurements also provided input parameters to the numerical prediction. However, numerical results showed...
Inlet temperature is one of the main inputs in all models for the analysis of fluid film bearing performance. At the same time, inlettemperature distribution and also oil velocity distribution at the inlet are the result of flow phenomena in the gap between the bearingpads. These phenomena are complex and in many cases further affected by any special arrangements of forced oil supply to the gapbetween pads. The reason for such...
The paper presents an experimental study of the influence of oil additives (Cl, S, P, cerium dioxide (CeO2)) on spread cracks in silicon nitride. The additives Cl, S, P are bound in molecules in liquid form soluble in the base oil. The CeO2 is purely in powder form in suspension. The use of CeO2 powder was made based on the good results of polishing of silicon nitride. A ceramic angular contact ball bearing was modelled using a...
seen 311 times