prof. dr hab. inż. Maria Gazda
Employment
- Professor at Instytut Nanotechnologii i Inżynierii Materiałowej
- Head of Section at Zakład ceramiki
Research fields
Publications
Filters
total: 222
Catalog Publications
Year 2019
-
A negative effect of carbon phase on specific capacity of electrode material consisted of nanosized bismuth vanadate embedded in carbonaceous matrix
PublicationLithium-ion batteries (LIBs) are widely used all over the world. The LIBs belong to a renewable energy source and energy storage devices. The increase in energy demand causes that new materials of higher energy and higher power densities are still under investigation. Herein, we compare electrochemical properties of bismuth vanadate (BiVO4) embedded and not embedded into carbonaceous matrix as an anode material along with structural...
-
Copper and cobalt co-doped ceria as an anode catalyst for DIR-SOFCs fueled by biogas
PublicationThe nanocrystalline compounds of Co and Cu co-doped ceria (with up to 20 mol.% of dopants) were fabricated by the reverse microemulsion synthesis method. They were deposited in a form of layers on the surface of SOFC anode in an aim to act as electrochemically active materials for biogas reforming process. Fourier Transformed Infrared Spectroscopy was used to analyze a composition of outlet gases simultaneously with the tests of...
Year 2020
-
Antimony substituted lanthanum orthoniobate proton conductor – structure and electronic properties.
PublicationX‐ray and neutron diffraction have been utilized to analyze the crystalline and electronic structure of lanthanum orthoniobate substituted by antimony. Using X‐ray absorption spectroscopy and photoelectron spectroscopy, changes in the electronic structure of the material upon substitution have been analyzed. The structural transition temperature between fergusonite and scheelite phases for 30 mol% antimony substitution was found...
-
Ceramic composites for single-layer fuel cells
PublicationComposite materials consisting of acceptor doped lanthanum orthoniobate electrolyte phase (La0.98Ca0.02NbO4) and Li2O:NiO:ZnO semiconducting phase were synthesized. The precursor powder of La0.98Ca0.02NbO4 was prepared in nanocrystalline (mechanosynthesis) and microcrystalline (solid-state synthesis) form. The composite can be applied in a single-layer fuel cell, because of the presence of two phases acting as an anode and a cathode...
-
Conductivity, structure, and thermodynamics of Y2Ti2O7–Y3NbO7 solid solutions
PublicationThe defect fluorite yttrium niobate Y3NbO7 and pyrochlore yttrium titanate Y2Ti2O7 solid solutions have been synthesized via a solid state synthesis route. The resulting stoichiometry of the oxides is Y2+xTi2−2xNbxO7, where x = 0 to x = 1. All of the samples were single-phase; however, for those with a predominant fluorite phase, a small amount of additional pyrochlore phase was detected. The volume of the solid solution unit cells...
-
Electric and magnetic properties of Lanthanum Barium Cobaltite
PublicationThe cubic Ba0.5La0.5CoO3‐δ was synthesized using solid state reaction. The structural properties were determined by the simultaneous refinement of Synchrotron Powder X‐ray Diffraction and Neutron Powder Diffraction data. Iodometric titration was used to examine the oxygen stoichiometry and average cobalt oxidation state. Low‐temperature magnetic studies show soft ferromagnetic character of fully oxidized material, with θP = 198(3)...
Year 2013
-
Application of wet powder spraying for anode supported solid oxide fuel cell with a perowskite SrTi0.98Nb0.02O3-d anode
PublicationAnode-supported solid oxide fuel cell with SrTi0.98Nb0.02O3–d anode, yttria-stabilized zirconia electrolyte and La(Ni0.6Fe0.4) O3d cathode has been successfully fabricated and evaluated. Process of anode support fabrication has been presented. Wet powder spraying and high temperature sintering method have been studied and applied to deposit the thin electrolyte layer.In order to improve catalytic properties of the anode, it has...
-
Auksetyczne pianki poliuretanowe
PublicationPrzedmiotem badań były auksetyczne pianki poliuretanowe wytworzone metodą trójosiowej termo-kompresji z konwencjonalnych elastycznych pianek poliuretanowych. Materiały auksetyczne charak-teryzują się ujemnym współczynnikiem Poissona i dzięki swojej strukturze komórkowej charakteryzują się unikalnymi właściwościami fizyko-mechanicznymi. Zbadano wpływ trójosiowej termokompresji na zmianę właściwości mechanicznych oraz struktury otrzymanej...
-
Characterization of CaTi0.9Fe0.1O3/La0.98Mg0.02NbO4 composite
PublicationA composite of CaTi0.9Fe0.1O3 and electrolyte material, i.e. magnesium doped La0.98Mg0.02NbO4 was prepared and studied. The phase content and the sample microstructure was examined by an X-ray diffraction method and scanning electron microscopy. EDS measurements were done both for composite samples and the diffusion couple. The electrical properties were studied by four terminal DC method. The Ahigh-temperature interaction between...
-
EFFECTS OF DOPING ON STRUCTURE AND PHASE TRANSITION OF HIGH TEMPERATURE PROTON CONDUCTOR LaNb1-xMxO4-σ (M=As, Sb, V, Ta AND X=0,05 TO 0,3)
PublicationIn this work synthesis of lanthanum orthoniobate has been done. Doping by arsenic, antimony, vanadium or tantalum in 5% to 30% have been introduced. The relationship between doping type and percentage and structural properties of the material have been investigated.
Year 2009
-
Applications of spin coating of polymer precursor and slurrysuspensions for Solid Oxide Fuel Cell fabrication
PublicationW pracy przedstawiono możliwości zastosowania w tlenkowych ogniwach paliwowych metody nanoszenia wirowego prekursorów polimerowych i zawiesin. Przedstawiono przykłady zastosowania tej metody do wytworzenia elektrolitu oraz warstw ochronnych dla stali nierdzewnych.
-
Boron-doped TiO2: Characteristics and photoactivity under visible light
PublicationOtrzymano TiO2 domieszkowany borem aktywny w reakcjach fotodegradacji pod wpływem światła widzialnego (λ>400 nm). Fotokatalizatory otrzymano poprzez hydrolizę tytanianu(IV) izopropylu w obecności związków boru lub poprzez ucieranie TiO2 (ST-01, P25 i A11) z prekursorami B i następnie kalcynację w zakresie temperatur 200-600oC. Jako źródło boru zastosowano kwas borowy lub ester trietylowy kwasu borowego. Najwyższą aktywność pod...
-
Chemical characteristics of new nanopowder of titania doped with nitrogen atoms
PublicationW pracy zaprezentowano charakterystykę domieszkowanego azotem ditlenku tytanu otrzymanego na drodze jednoetapowej syntezy z kompleksu tytanu (IV) z ligandami zawierającymi atomy azotu. ikrostruktura i morfologia nowego materiału została określony za pomocą badań XRD, AFM, UV-VIS i FT-IR. Raport przedstawia również badania elektrochemiczne, które pozowliły na wyznaczenie potencjału pasma płaskiego na podstawie wykresu Mott
-
Conductivity improvement of Ce0.8Gd0.2O1.9 solid electrolyte
PublicationW pracy przedstawiono metodę zwieszenia przewoności domieszkowanego tlenku ceru wprowadzając podczas syntezy 2% wapnia. Zbadano metody wprowadzenia wapnia z użyciem prekursorów polimerowych. Uzyskano zwiększenie przewodności oraz syntezowalności elektrolitu stałego.
-
Electrical and structural properties of Nb-doped SrTiO3 ceramics
PublicationPrzebadano wpływ zawartości niobu na strukturę i własności elektryczne tytanianu strontu. Zbadany został wpływ warunków redukcji i porowatości na właściwości materiału. Za optymalne uznano domieszkowanie niobem w wysokości 2% molowych.
-
Electrical properties of Y0.08Sr0.92Ti0.92Nb0.08O3_−delta after reduction in different reducing conditions
PublicationPraca przedstawia badania właściwości elektrycznych perowskitów Y0.08Sr0.92Ti0.92Nb0.08O3−ı redukowanych w różnych warunkach termicznych. Obserwowano wysoką przewodność elektryczną próbek redukowanych w atmosferze amoniaku. Przewodność Y0.08Sr0.92Ti0.92Nb0.08O3−ı redukowanego w amoniaku w 1500 ◦C była rzędu 600 S/cm w 200 ◦C. Przewodność elektryczna próbek redukowanych w amoniaku w 1500 ◦C była stabilna zarówno w atmosferze wodoru...
-
Electrical properties of Y0.08Sr0.92Ti0.92Nb0.08O3-δ after reduction in different reducing conditions
PublicationElectrical properties of perovskite Y0.08Sr0.92Ti0.92Nb0.08O3−ı after reduction in different conditions were studied. Relatively high electrical conductivity in samples reduced in ammonia was observed. The conductivity of Y0.08Sr0.92Ti0.92Nb0.08O3−ı reduced in ammonia at 1500 ◦C was of about 600 S/cm at 200 ◦C. Conductivity after reduction in ammonia at 1500 ◦C was stable both in hydrogen and oxygen atmosphere up to 600 ◦C. Reduction...
Year 2017
-
Biosilica from sea water diatoms algae—electrochemical impedance spectroscopy study
PublicationHere, we report on an electrochemical impedance study of silica of organic origin as an active electrode material. The electrode material obtained from carbonized marine biomass containing nanoporous diatoms has been characterised by means of XRD, IR, SEM and EIS. Dif- ferent kinds of crystallographic phases of silica as a result of thermal treatment have been found. The electrode is electrochemically stable during subsequent cyclic...
-
Comprehensive study on graphene hydrogels and aerogels synthesis and their ability of gold nanoparticles adsorption
PublicationGraphene hydrogels were prepared by ascorbic acid-assisted gelation of graphene oxide (GO) aqueous suspensions both in acidic and basic conditions. Different mass ratio of ascorbic acid (AA) to GO was used (namely 20:1 and 10:1). In order to eliminate the influence of AA on the final structure of hydrogels, samples without AA were prepared by a hydrothermal gelation of GO in an autoclave. An in-depth structural characterization...
-
Effect of irradiation intensity and initial pollutant concentration on gas phase photocatalytic activity of TiO2 nanotube arrays
PublicationWell-organized TiO2 nanotube arrays were fabricated via one-step anodization process. The as-prepared TiO2 nanotubes were characterized by X-ray powder diffractometry (XRD), X-ray photoelectron spectroscopy (XPS), diffuse reflectance spectroscopy (DRS) and scanning electron microscopy (SEM). Photocatalytic activity of obtained photocatalyst was studied in reaction of toluene degradation in the gas phase using low powered and low...
-
Electrodes consisting of PEDOT modified by Prussian Blue analogues deposited onto titania nanotubes – Their highly improved capacitance
PublicationIn this work we present the outstanding energy storage of prepared inorganic-organic heterojunction where hydrogenated ordered titania nanotubes (H-TiO2NT) were modified by the hybrid made of poly(3,4-ethylenedioxythiophene) (pEDOT) and iron hexacyanoferrate centres (Fehcf, Prussian Blue). The material TiO2NT/pEDOT:Fechf was obtained electrochemically by means of: anodization, hydrogenation and finally, electropolymerization of...
Year 2008
-
(Bi,Pb)-Sr-Ca-Cu-O glass-ceramics - superconductor and granular metal
PublicationW materiale o składzie (Bi,Pb)-Sr-Ca-Cu-O wskutek stosowania różnych warunków wytwarzania można otrzymać materiały o różnorodnych właściwościach. W efekcie wygrzewania materiał amorficzny częściowo krystalizuje. To powoduje wzrost rozmiaru i zawartości przewodzących i nadprzewodzących granul oraz zmniejszenie szerokości izolujących barier pomiędzy granulami. Zależność temperaturowa oporu słabo skrystalizowanego materiału jest funkcją...
-
Chapter 31. Preparation of silver doped titanium dioxide nanoparticles in microemulsion system
PublicationNanocząstki TiO2 domieszkowanego srebrem przygotowano w mikroemulsji woda-AOT-cykloheksan. Zbadano wpływ zawartości srebra (od 1,5 do 8,5% mol.) na aktywność fotokatalityczą oraz właściwości bakterio- i grzybobójcze. Stwierdzono, że TiO2 modyfikowany za 6,5% mol. Ag wykazuje najwyższą aktywność w reakcji degradacji fenolu oraz najwyższą aktywność mikrobiologiczną. Aktywność mikrobiologiczną wyznaczano jako minimalne stężenie hamujące...
-
Chemical interaction between perovskite La0.6Sr0.4FeO3 and Super-Ionic Zr0.84Y0.16Ox
PublicationW pracy przedstawiono wyniki badań interakcji chemicznej pomiędzy materiałem perowskitowym LSF a materiałem superjonowym YSZ. Materiał superjonowy został wytworzony w niskiej temperaturze z użyciem prekusora polimerowego i zawiesiny proszku ceramicznego.W badaniach korzystano z spektroskopii rentgenowskiej.
-
Conductivity and superconductivity in granular materials
PublicationMetale i nadprzewodniki granulaste są bardzo ciekawymi materiałami dzięki jednoczesnej obecności oddziaływań kulombowskich, tunelowania elektronów i par Coopera oraz różnych zjawisk związanych z nieuporządkowaniem. W pracy przedstawiono i porównano niektóre właściwości granulastych nisko- i wysokotemperaturowych nadprzewodników. Granulasty nadprzewodnik wysokotemperaturowy otrzymano metodą krystalizacji w fazie stałej szkła (Bi,Pb)-Sr-Ca-Cu-O....
-
Effect of structure modification with potassium on grains layer creation process and phase transitions
PublicationZbadano szkła germanianowo-ołowiowe i krzemianowo bizutowe. Wartwy metalicznych granul wytwarzano w nich poprzez redukcję powierzchni w atmosferze wodoru. Praca dotyczy wpływu potasu na tworzenie się warstwy granul oraz na procesy topnienia i krzepnięcia granul w trakcie obróbki termicznej.
-
Electrical properties of poros nanocrystalline undoped ceria oxygen sensor
PublicationW pracy zaprezentowano wykonanie czujnika z niedomieszkowanego tlenku ceru o nanometrowych ziarnach krystalicznych. Zastosowana metoda nanoszenia warstw zalicza się do metod niskotemperaturowych. Wytworzone warstwy przebadano za pomocą dyfrakcji rentgenowskiej, mikroskopii elektronowej oraz spektroskopii impedancyjnej. Wykonane czujniki charakteryzują się szybkim czasem odpowiedzi i stabilnym zachowaniem przy zmianach ciśnienia...
Year 2014
-
Cadmium complex possessing simultaneously silanethiolato- and dithiocarbamato-ligands. A novel single-source precursor of cadmium sulfide
PublicationThermal decomposition of suitable coordination compounds may be used as efficient route for fabrication of semiconducting layers. A new potential CdS precursor—a cadmium complex with all-sulfur Cd-coordination sphere [Cd{l-SSi(OBut)3}(S2CNC4H8)]2 (1) —has been prepared and its properties are investigated. The complex was obtained in the reaction between dimeric bis(tri-tert-butoxysilanethiolato) cadmium(II) [Cd{SSi(OBut)3}2]2 and...
-
Correlation between structural and electrical properties in highly porous (Y,Sr)(Ti,Nb)O3-delta SOFC anodes
PublicationIn order to find a relationship between structural and electrical properties, niobium and yttrium doped SrTiO3 ceramics were prepared via solid-state reaction. The samples were sintered in hydrogen and air conditions. The samples were also fabricated with a pore-former to obtain highly porous specimens. The electrical properties of Nb-doped SrTiO3 samples and yttrium and niobium co-doped SrTiO3 were compared. The comparable electrical...
-
Effect of isovalent substitution on microstructure and phase transition of LaNb1−xMxO4 (M=Sb, V or Ta; x=0.05–0.3)
PublicationLaNb1−xMxO4 oxides with pentavalent elements of different ionic sizes (M=Sb, Ta and V, x=0.05–0.3) were synthesized by the solid state reaction method. Special interest was devoted to the antimony substituted lanthanum niobate which is a new material in this group. Rietveld analysis of the X-ray diffraction patterns was used to determine the influence of the material composition on unit cell parameters. On the basis of dilatometric...
-
Electrical properties and structure of lead-borate glass containing iron ions.
PublicationThe ac and dc conductivity in iron–lead-borate glass samples was investigated in the frequency range from 1 mHz to 1 MHz and in the temperature range from 153 K to 423 K. The structure was investigated by the means of atomic force microscopy (AFM) and the crystalline phases (if present) were identified by the means of X-ray diffractometry. Two types of ac electrical behaviour were observed. The first group of glass samples which...
Year 2012
-
Cavitation Erosion Resistance of Austenitic Stainless Steel after Glow-Discharge Nitriding Process
PublicationThis paper presents investigation of cavitation erosion resistance of nitrided austenitic stainless steel X5CrNi18-10. The diffusion layers were produced by using different parameters of atmosphere (N2:H2). The microstructure, chemical composition and phase identification of the modified layer were examined using scanning electron microscopy, glow-discharge optical emission spectrometer and X-ray diffractometry, respectively. Cavitation...
-
Donor-substituted SrTi1+xO3−δ anodes for SOFC
PublicationPrzebadano wpływ niestechiometrii na właściwości tytanianu strontu domieszkowanego niobem. Zaproponowano chemię defektów dla tego typu związków.
-
Donor-substituted SrTi1+xO3−δ anodes for SOFC
PublicationNonstoichiometric Nb-substituted SrTiO3 compounds were investigated in order to discuss the influence of nonstoichiometry at the sample properties in the light of recent results reported in the literature. Structural and electrical properties of samples were characterized. Investigated compounds were also applied as anodes for Solid Oxide Fuel Cells and their reactivity with YSZ electrolyte was examined. The defect chemistry explaining...
Year 2015
-
Characterization of magnesium doped lanthanum orthoniobate synthesized by molten salt route
PublicationMolten salt synthesis method has been used to prepare the single phase magnesium doped lanthanum orthoniobate. The phase composition has been checked by X-ray diffraction method and the microstructure studies have been performed by scanning electron microscopy. The high temperature properties of the material have been investigated by thermogravimetry and electrochemical impedance spectroscopy. A dependence between sample total...
-
Electrical conductivity and relaxation processes in V2O5 nanorods prepared by sol–gel method
PublicationProperties of high purity V2O5 nanorods prepared by a sol – gel method are presented. The studied materials were characterized by: X-ray diffractometry (XRD), scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS). The electrical impedance was measured as a function of temperature and frequency. The obtained results show that the electrical conductivity increases with increasing temperature. The d.c. conductivity...
-
Electronic and ionic relaxations in strontium-borate glass and glass-ceramics containing bismuth and vanadium oxides
PublicationThe topography, microstructure and electrical properties of strontium-borate glass and SBO glass containing bismuth and vanadium oxides, were studied. The structure was measured using X-ray diffraction (XRD), Energy Dispersive X-ray Spectrometer (EDS) and Scanning electron microscope (SEM) methods. The A.C. complex conductivity was investigated as a function of temperature and frequency. The influence of the quantity of bismuth...
Year 2016
-
Characterization of structural, thermal and mechanical properties of bismuth silicate glasses
Publicationhe influence of heating and reduction processes on the structural, thermal and mechanical properties of bismuth-silicate glasses has been investigated. Two compositions of glasses: 40Bi2O3–60SiO2 (Bi0.57Si0.43Ox) and 27Bi2O3–73SiO2 (Bi0.43Si0.57Ox) were fabricated by a typical melt quenching technique. Then the reduction in hydrogen at 380 °C for 20, 42 or 67 h was performed. It was found that a 50 μm-thick layer was formed on...
-
Determination of the ionic conductivity of Sr-doped lanthanum manganite by modified Hebb–Wagner technique
PublicationThe Hebb–Wagne rpolarization method with the electron blocking electrode has been discussed in this paper in aim to determine a partial ionic conductivity of Sr-doped lanthanum manganite.The “limiting current” in the proposed system was measured using the two-point DC technique with additional Pt electrode between LSM and blocking electrode.The electrochemical model based on bulk diffusion processes and Boltzmann statistics has...
Year 2010
-
Charakterystyka fotokatalizatorów aktywnych w świetle widzialnym
PublicationNanocząstki typu Ag-TiO2, Au-TiO2 oraz Ag/Au-TiO2 zawierające od 0,5 do 4,5% Ag i/lub Au otrzymano poprzez redukcję prekursorów Ag i/lub Au za pomocą promieniowania g oraz metodą redukcji w mikroemulsji. Charakterystyka otrzymanych fotokatalizatorów obejmowała wyznaczenie właściwości absorpcyjnych, powierzchni właściwej BET, badanie aktywności fotokatalitycznej, badanie składu powierzchniowego metodą XPS oraz wyznaczenie struktury...
-
Electrical and structural properties of Nb-doped SrTiO3
PublicationNiobium-doped strontium titanate synthesized via conventional solid-state reaction has been studied. Influence of niobium content on the lattice parameters and electrical conductivity has been reported. Various reduction conditions have been investigated. For samples reduced in hydrogen at 1400°C, a transition from thermally activated to metallic behavior has been observed. Maximum electrical conductivity (ca. 55 Scm−1 at 650°C)...
Year 2023
-
Charge Transport in High-Entropy Oxides
PublicationThis work presents the results of research on the transport properties of the high-entropy BaZr1/8Hf1/8Sn1/8Ti1/8Y1/8In1/8Sm1/8Yb1/8O3–x perovskite oxide with special focus on proton transport. The presented study is part of broader work in which we focus on multiple different chemical compositions with the cation number varying from 5 up to 12 (in B-sublattice). The presence of proton defects is analyzed with thermogravimetry,...
Year 2011
-
Coatings for improvement of high temperature corrosion resistance of porous alloys
PublicationPorowate stopy metaliczne są potencjalnymi podłożami nośnymi dla tlenkowych ogniw paliwo. Ich stosowanie obniża cenę ogniw paliwowych, co zaowocuje ich szybszą komercjalizacą. Jednak są one podatne na korozję w wysokich temperaturach. Dotychczas brak jest metod, które mogą poprawić rezystancję korozyjną porotawych stopów w wysokich temperaturach porowatych stopy do zastosowań SOFC. W tym artykule zaproponowano sposób na poprawę...
Year 2007
-
Conductivity and superconductivity of (Bi,Pb)4Sr3Ca3Cu4Ox glass-ceramics
PublicationAmorficzny materiał (Bi,Pb)4Sr3Ca3Cu4Ox w zależności od warunków wygrzewania może być albo granulastym materiałem albo silnie nieuporządkowanym metalem. W pracy przedstawiony jest wpływ mikrostruktury na właściwości elektryczne w stanie normalnym oraz przejście do stanu nadprzewodzącego.
-
Conductivity and superconductivity of (Bi,Pb)-Sr-Ca-Cu-O
PublicationAmorficzny materiał (Bi,Pb)4Sr3Ca3Cu4Ox w zależności od warunków wygrzewania może być albo granulastym materiałem albo silnie nieuporządkowanym metalem. Przejście do stanu nadprzewodzącego zachodzi w materiałach, w których Josephsonowskie sprzężenie między granulami jest silniejsze niż oddziaływania Coulombowskie.
-
Electrical conductivity of disordered (Bi,Pb)-Sr-Ca-Cu-O materials
PublicationAmorficzny materiał (Bi,Pb)4Sr3Ca3Cu4Ox wygrzewany w odpowiednich warunkach staje się nieuporządkowanym metalem i nadprzewodnikiem. Ma duży opór i zazwyczaj ujemny współczynnik temperaturowej zależności oporu. W pracy dyskutowane są właściwości w stanie normalnym oraz przejście do stanu nadprzewodzącego.
Year 2004
-
Conductivity and superconductivity of (Bi,Pb)4Sr3Ca3Cu4Ox glass-ceramics.
PublicationW układzie(Bi,Pb)-Sr-Ca-Cu-O poprzez krystalizację w fazie stałej można wytworzyć materiały o bardzo różnych właściwościach elektrycznych i nadprzewodzących. W zależności od warunków krystalizacji, można wytworzyć nadprzewodnik o temperaturze krytycznej między 8 a 105 st.K lub materiał nie przechodzący do stanu nadprzewodzącego. W pracy pokazano i przedyskutowano wpływ składu fazowego, struktury i mikrostruktury na przewodnictwo...
Year 2003
-
Copper defects and conductivity in Bi-Pb-Sr-Ca-Cu-O glasses.
Publication(Bi0.8Pb0.2) 4Sr3Ca3Cu4Ox częściowo skrystalizowane próbki otrzymano poprzez wygrzewanie szkła w wysokiej temperaturze. Badano je metodą EPR w zakresie temperatur od 4K do 300K. Koncentracja paramagnetycznych centrów Cu2+ zmniejsza się wraz ze wzrostem przewodnictwa elektrycznego i znika po skrystalizowaniu faz nadprzewodzących.
-
Electrical conductivity and superconductivity in (Bi-Pb)-Sr-Ca-Cu-O glassceramics during the first minutes of crystallisation.
Publication(Bi0.8Pb0.2)4Sr3Ca3Cu4Ox częściowo skrystalizowane próbki otrzymano poprzez wygrzewanie szkła w temperaturze między 700st.C i 870st.C przez krótki czas.Pomiary temperaturowej zależności oporności przeprowadzono metodą 4-punktową w temperaturze od 3K do 300K. Przeprowadzono również pomiary przewodności w czasie trwania wygrzewania. Stwierdzono, że w czasie wygrzewania następuje stopniowa zmiana mechanizmu przewodnictwa. Niektóre...
Year 2005
-
Effect of preparation conditions on superconducting properties of (Bi,Pb)-Sr-Ca-Cu-O glass-ceramics
PublicationPraca przedstawia wpływ warunków krystalizacji na właściwości nadprzewodzące nadprzewodników wysokotemperaturowych (Bi,Pb)-Sr-Ca-Cu-O otrzymanyh metodą krystalizacji w fazie stałej. Nadprzewodniki otrzymano poprzez wygrzewanie amorficznego materiału o składzie (Bi0.8Pb0.2)4Sr3Ca3Cu4Ox w temperaturze pomiędzy 750°C i 865°C przez czas od 1 minuty do 43 godzin. Najlepsze właściwości, w w tym dużą gęstość prądu krytycznego otrzymano...
seen 5165 times