Repository Open Access
Filters
total: 3553
displaying 1000 best results Help
Catalog Publications
2021
-
A 95-Year-Old Concrete Arch Bridge: From Materials Characterization to Structural Analysis
PublicationThe structural analysis of a 95-year-old concrete arch bridge located in Jagodnik (Poland) is performed in this paper, in order to check its behavior under today’s traffic loads. The mechanical properties of both the concrete and the reinforcement are investigated by testing cores and bar stubs extracted from the bridge. Structural analysis confirms that the bridge meets today’s load requirements in terms of bearing capacity, serviceability...
-
A dynamic vehicle-bridge model based on the modal identification results of an existing EN57 train and bridge spans with non-ballasted tracks
PublicationThis paper addresses the methodology of the bridge-vehicle dynamic model definition based on the free response measurements of an existing train and existing bridge spans. In the case of the railway vehicle, the methodology uses the impulse excitations of a single car by means of the wedge method. In the case of the bridge spans, free responses are collected after the passages of trains. The global modal parameters (frequencies...
-
A Model-Order Reduction Approach for Electromagnetic Problems With Nonaffine Frequency Dependence
PublicationThe aim of this paper is to present a novel model-order reduction (MOR) technique for the efcient frequency-domain nite-element method (FEM) simulation of microwave components. It is based on the standard reduced-basis method, but the subsequent expansion frequency points are selected following the so-called sparsied greedy strategy. This feature makes it especially useful to perform a fast-frequency sweep of problems that lead...
-
A New Approach to the PWM Modulation for the Multiphase Matrix Converters Supplying Loads with Open-End Winding.
PublicationThis article presents three variants of the Pulse Width Modulation (PWM) for the Double Square Multiphase type Conventional Matrix Converters (DSM-CMC) supplying loads with the open-end winding. The first variant of PWM offers the ability to obtain zero value of the common-mode voltage at the load's terminals and applies only six switches within the modulation period. The second proposal archives for less Total Harmonic Distortion...
-
A Novel Versatile Decoupling Structure and Expedited Inverse-Model-Based Re-Design Procedure for Compact Single-and Dual-Band MIMO Antennas
PublicationMultiple-input multiple-output (MIMO) antennas are considered to be the key components of fifth generation (5G) mobile communications. One of the challenges pertinent to the design of highly integrated MIMO structures is to minimize the mutual coupling among the antenna elements. The latter arises from two sources, the coupling in the free space and the coupling currents propagating on a ground plane. In this paper, an array of...
-
A Qualitative Study on Non-functional Requirements in Agile Software Development
PublicationWidespread use of agile software development (ASD) methods can be observed nowadays. Non-functional requirements (NFRs) are often reported to be a problematic issue for agile projects, since ASD methods tend to neglect NFRs while focusing on incremental delivery of functional features. Despite that, only very few studies have explored the requirements engineering practices used in ASD and dedicated particularly to NFRs. Objective:...
-
A sense of security and freedom in a residential environment
PublicationThe article is based on the results of a survey carried out among students of architecture faculties in several countries, which examined the students’ knowledge of shaping the housing environment in such a way as to enable them to fulfil two basic and, at the same time, seemingly mutually exclusive psychological needs of a person: a sense of security and a sense of freedom. In examining these issues, particular emphasis was placed...
-
A technique of experiment aided virtual prototyping to obtain the best spindle speed during face milling of large-size structures
PublicationThe paper presents an original method concerning vibration suppression problem during milling of large-size and geometrically complicated workpieces with the use of novel way of selecting the spindle speed. This consists in repetitive simulations of the cutting process for subsequent values of the spindle speed, until the best vibration state of the workpiece is reached. An appropriate method of obtaining a computational model,...
-
Accurate Modeling of Frequency Selective Surfaces Using Fully-Connected Regression Model with Automated Architecture Determination and Parameter Selection Based on Bayesian Optimization
PublicationSurrogate modeling has become an important tool in the design of high-frequency structures. Although full-wave electromagnetic (EM) simulation tools provide an accurate account for the circuit characteristics and performance, they entail considerable computational expenditures. Replacing EM analysis by fast surrogates provides a way to accelerate the design procedures. Unfortunately, modeling of microwave passives is a challenging...
-
AMO perspectives on the well-being of neurodivergent human capital
PublicationExisting management research and management practices frequently overlook the relationship between the above-average human capital of highly functioning neurodivergent employees, their subjective well-being in the workplace and performance outcomes. This paper calls for greater attention to the hidden human capital associated with neurodiversity by mainstreaming implementation of neurodiversity-friendly policies and practices. Drawing...
-
Antifungal Activity of Capridine β as a Consequence of Its Biotransformation into Metabolite Affecting Yeast Topoisomerase II Activity
PublicationIn the last few years,increasing importance is attached to problems caused by fungal pathogens. Current methods of preventing fungal infections remain unsatisfactory. There are several antifungal compounds whichare highly effective in some cases, however, they have limitations in usage: Nephrotoxicity and other adverse effects. In addition, the frequent use of available fungistatic drugs promotes drug resistance....
-
Application analysis of a hybrid solid oxide fuel cell-gas turbine system for marine power plants
PublicationThe results of theoretical studies of the possibilities of using hybrid solid oxide fuel cell–gas turbine (SOFC-GT) systems for marine power plants are presented. A 500 kW auxiliary marine power plant scheme using stacks of SOFCs in combination with a regenerative gas turbine operating with over-expansion based on our recent patent application is proposed. The results of mathematical modelling showed the opportunity to obtain a...
-
Applications of Additively Manufactured Tools in Abrasive Machining—A Literature Review
PublicationHigh requirements imposed by the competitive industrial environment determine the development directions of applied manufacturing methods. 3D printing technology, also known as additive manufacturing (AM), currently being one of the most dynamically developing production methods, is increasingly used in many different areas of industry. Nowadays, apart from the possibility of making prototypes of future products, AM is also used...
-
Arithmetic Loophole in Bell's Theorem: Overlooked Threat to Entangled-State Quantum Cryptography
PublicationBell’s theorem is supposed to exclude all local hidden-variable models of quantum correlations. However,an explicit counterexample shows that a new class of local realistic models, based on generalized arith-metic and calculus, can exactly reconstruct rotationally symmetric quantum probabilities typical oftwo-electron singlet states. Observable probabilities are consistent with the usual arithmetic employedby macroscopic observers...
-
ASSESSMENT OF VOLATILE ORGANIC COMPOUNDS EMISSIONS FROM RECYCLED LOW-DENSITY POLYETHYLENE STREAMS
PublicationThe recycling of plastics is currently one of the most significant industrial challenges. Due to the enormous amounts of plastic wastes generated by various industry branches, it is essential to look for the potential methods of their utilization. Nevertheless, it should not be forgotten that recycled plastics are not pure materials, and they still may show an unfavorable environmental impact. They may contain different contaminants...
-
Bee Bread Exhibits Higher Antimicrobial Potential Compared to Bee Pollen
PublicationThis study aimed at investigation of the antimicrobial potential of ethanolic extracts of bee bread (BB) and bee pollen (BP) and suspensions of these products in MHB (Mueller Hinton Broth). We covered 30 samples of BP and 19 samples of BB harvested in Polish apiaries. Slightly lower activity was observed against Gram-negative bacteria compared to Gram-positive staphylococci. BB extracts exhibited higher inhibitory potential with...
-
Behavior of residual current devices at frequencies up to 50 kHz
PublicationThe use of residual current devices (RCDs) is obligatory in many types of low-voltage circuits. They are devices that ensure protection against electric shock in the case of indirect contact and may ensure additional protection in the case of direct contact. For the latter purpose of protection, only RCDs of a rated residual operating current not exceeding 30 mA are suitable. Unfortunately, modem current-using equipment supplied...
-
Biomass-Derived Nitrogen Functionalized Carbon Nanodots and Their Anti-Biofouling Properties
PublicationThe prevalence of the antibiotic resistant bacteria remains a global issue. Cheap, sustainable and multifunctional antibacterial membranes are at the forefront of filtrating materials capable of treating multiple flow streams, such as water cleansing treatments. Carbon nanomaterials are particularly interesting objects shown to enhance antibacterial properties of composite materials. In this article, amino-functionalized, photoluminescent...
-
Block graphs with large paired domination multisubdivision number
PublicationThe paired domination multisubdivision number of a nonempty graph G, denoted by msdpr(G), is the smallest positive integer k such that there exists an edge which must be subdivided k times to increase the paired domination number of G. It is known that msdpr(G) ≤ 4 for all graphs G. We characterize block graphs with msdpr(G) = 4.
-
By-Products from Food Industry as a Promising Alternative for the Conventional Fillers for Wood–Polymer Composites
PublicationThe present paper describes the application of two types of food-industry by-products, brewers’ spent grain (BSG), and coffee silverskin (ŁK) as promising alternatives for the conventional beech wood flour (WF) for wood–polymer composites. The main goal was to investigate the impact of partial and complete WF substitution by BSG and ŁK on the processing, structure, physicochemical, mechanical, and thermal properties of resulting...
-
Cascade Object Detection and Remote Sensing Object Detection Method Based on Trainable Activation Function
PublicationObject detection is an important process in surveillance system to locate objects and it is considered as major application in computer vision. The Convolution Neural Network (CNN) based models have been developed by many researchers for object detection to achieve higher performance. However, existing models have some limitations such as overfitting problem and lower efficiency in small object detection. Object detection in remote...
-
Chain Action - How Do Countries Add Value Through Digital Government?
PublicationThis study examineshow countries develop and benefit from Digital Government(DG).The literature proposes various conceptualizations of the value-adding logic of DG, but the benchmarking practice is not respondingto such proposals.For instance, the United Nations’E-Government Surveycombines the readiness and uptake indicatorsand failsto cover any impactindicators;thus,its diagnostic valueis limited. To overcome...
-
Characterization of Arctic Driftwood as Naturally Modified Material. Part 1: Machinability
PublicationArctic driftwood has reached the coast of Iceland for centuries. This material was used by the inhabitants of the island as a building material for houses, boats, churches and pasture fences. Nowadays, the driftwood is used in the furniture industry, for the finishing of internal and external walls of buildings and also by artists. The properties of driftwood differ to that of original resource due the long-term effects of exposure...
-
Chemical, Physical, and Mechanical Properties of 95-Year-Old Concrete Built-In Arch Bridge
PublicationThis research aimed to determine the durability and strength of an old concrete built-in arch bridge based on selected mechanical, physical, and chemical properties of the concrete. The bridge was erected in 1925 and is located in Jagodnik (northern Poland). Cylindrical specimens were taken from the side ribs connected to the top plate using a concrete core borehole diamond drill machine. The properties of the old concrete were...
-
Coffee Silverskin as a Multifunctional Waste Filler for High-Density Polyethylene Green Composites
PublicationThis work aims to describe the coffee silverskin effect as a lignocellulosic waste filler for high-density polyethylene (HDPE) composites development. The main task was to determine various modification effects resulting from the complex chemical composition of coffee silverskin containing compounds with potential antioxidative properties, including caffeine, polyphenols, tannins, or melanoidins. The processing, thermal, physicochemical,...
-
Coffee silverskin as a potential bio-based antioxidant for polymer materials: Brief review
PublicationCoffee silverskin is one of the by-products generated by the coffee industry. Although it is not the most burdensome one, because it stands only for ~4.2 wt % of coffee, it seems like an auspicious raw material for industrial processes. Coffee silverskin is characterized by a relatively low moisture content of ~5–7%, so it often does not require quite energy-consuming drying processes. The chemical composition of coffee silverskin,...
-
Company versus consumer performance: does brand community identification foster brand loyalty and the consumer’s personal brand?
PublicationThis study investigates the effect of community identification in building brand loyalty (attitudinal and behavioural) and a personal brand via social networks. The proposed model explained the main community identification antecedents and how identification can lead to enhanced company and consumer performance. This study adopts the theoretical lens of uses and gratifications theory and identifies three motivational drivers of...
-
Comparative Study of the Reinforcement Type Effect on the Thermomechanical Properties and Burning of Epoxy-Based Composites
PublicationAramid (AF), glass (GF), carbon (CF), basalt (BF), and flax (FF) fibers in the form of fabrics were used to produce the composites by hand-lay up method. The use of fabrics of similar grammage for composites’ manufacturing allowed for a comprehensive comparison of the properties of the final products. The most important task was to prepare a complex setup of mechanical and thermomechanical properties, supplemented by fire behavior...
-
Comparison of Absorbed and Intercepted Fractions of PAR for Individual Trees Based on Radiative Transfer Model Simulations
PublicationThe fraction of absorbed photosynthetically active radiation (fAPAR) is a key parameter for estimating the gross primary production (GPP) of trees. For continuous, dense forest canopies, fAPAR, is often equated with the intercepted fraction, fIPAR. This assumption is not valid for individual trees in urban environments or parkland settings where the canopy is sparse and there are well-defined tree crown boundaries. Here, the distinction...
-
Complexes of silanethiolate ligands: Synthesis, structure, properties and application
PublicationThe purposeful syntheses of silanethiolate complexes started approximately in the mid-eighties of the 20th century but no summary of the synthetic efforts has been reported till now. The synthetic methods and the resulting complexes have some common features, which are emphasized throughout the review. Thereby specific difficulties during synthesis are outlined and the structures, properties and possible applications of the resulting...
-
Computational analysis of an infinite magneto-thermoelastic solid periodically dispersed with varying heat flow based on non-local Moore–Gibson–Thompson approach
PublicationIn this investigation, a computational analysis is conducted to study a magneto-thermoelastic problem for an isotropic perfectly conducting half-space medium. The medium is subjected to a periodic heat flow in the presence of a continuous longitude magnetic field. Based on Moore–Gibson–Thompson equation, a new generalized model has been investigated to address the considered problem. The introduced model can be formulated by combining...
-
Concept of managing quality in baking industry, in vector representation
PublicationThe author introduced an innovative metrisable method of describing a manufacturing process. The idea of vector structure of a manufacturing process allows to formulate quantitative relations between the activity of input streams, elements of product quality, and measurable effects of losses. The structure was basis for the formulation of the concept of the process of managing product quality in the baking industry in a vector...
-
Coupling between Blood Pressure and Subarachnoid Space Width Oscillations during Slow Breathing
PublicationThe precise mechanisms connecting the cardiovascular system and the cerebrospinal fluid (CSF) are not well understood in detail. This paper investigates the couplings between the cardiac and respiratory components, as extracted from blood pressure (BP) signals and oscillations of the subarachnoid space width (SAS), collected during slow ventilation and ventilation against inspiration resistance. The experiment was performed on...
-
Curved Surface Minijet Impingement Phenomena Analysed with ζ-f Turbulence Model
PublicationThe jet impingement phenomenon plays an important role among the heat transfer intensification methods. Very often its application and analyses refer to simple flat surfaces, while there is a lack of information in the literature for cases addressing curved surfaces. In the present work, the single jet impingement on the non-flat (concave and convex) surface is studied for a wide range of geometries, which originate from the mini-jet...
-
Deep eutectic solvents based assay for extraction and determination of zinc in fish and eel samples using FAAS
PublicationA new assay based on effective (high recovery) extraction by means of deep eutectic solvents (DESs) was developed for ppb level determination of zinc in fishes and eel samples. Choline chloride and Phenol in a 1:2 M ratio was selected as optimal DES-based extraction solvent. 8-Hydroxy quinoline was used as a chelating agent for zinc ions. The optimized conditions were found at pH value of 8, ligand concentration of 10 mg/L, THF...
-
Defining a novel domain that provides an essential contribution to site-specific interaction of Rep protein with DNA
PublicationAn essential feature of replication initiation proteins is their ability to bind to DNA. In this work, we describe a new domain that contributes to a replication initiator sequence-specific interaction with DNA. Applying biochemical assays and structure prediction methods coupled with DNA–protein crosslinking, mass spectrometry, and construction and analysis of mutant proteins, we identified that the replication initiator of the...
-
Design principles for creating digital transparency in government
PublicationUnder pressure to fight corruption, hold public officials accountable, and build trust with citizens, many governments pursue the quest for greater transparency. They publish data about their internal operations, externalize decision-making processes, establish digital inquiry lines to public officials, and employ other forms of transparency using digital means. Despite the presence of many transparency-enhancing digital tools,...
-
Determinants of judges’ career choices and productivity: a Polish case study
PublicationThe goal of this paper is to identify factors which affect judges’ productivity and career choice motives with the view of increasing judicial efficiency. Specifically, the investigation focuses on such aspects as judges’ remuneration, promotion, threat of judgment revocation, service/mission, periodic assessment, the threat of a complaint about protracted proceedings or of disciplinary proceedings, the threat of destabilization...
-
Determination of the Theoretical and Actual Working Volume of a Hydraulic Motor—Part II (The Method Based on the Characteristics of Effective Absorbency of the Motor)
Publication: In this article, the second method of determination of the theoretical and actual working volume of a hydraulic motor is described. The proposed new method is based on the characteristics of effective absorbency of the motor. The effective absorbency has been defined as the ratio of flow rate in a motor to the rotational speed of the motor’s shaft. It has been shown that the effective absorbency is a nonlinear function of the...
-
Development of Strategies for AOB and NOB Competition Supported by Mathematical Modeling in Terms of Successful Deammonification Implementation for Energy-Efficient WWTPs
PublicationNovel technologies such as partial nitritation (PN) and partial denitritation (PDN) could be combined with the anammox-based process in order to alleviate energy input. The former combination, also noted as deammonification, has been intensively studied in a frame of lab and full-scale wastewater treatment in order to optimize operational costs and process efficiency. For the deammonification process, key functional microbes include...
-
Diphosphinoboranes as Intramolecular Frustrated Lewis Pairs: P–B–P Bond Systems for the Activation of Dihydrogen, Carbon Dioxide, and Phenyl Isocyanate
PublicationHerein, we present the first example of the activation of small molecules by P-B-P bond systems. The reactivity study involves reactions of two selected diphosphinoboranes, (tBu2P)2BPh (1’) and (Cy2P)2BNiPr2 (2), that differ in terms of their structural and electronic properties for the activation of dihydrogen, carbon dioxide, and phenyl isocyanate. Diphosphinoborane 1’ activates H2 under very mild conditions in the absence of...
-
Disinfection characteristics of an advanced rotational hydrodynamic cavitation reactor in pilot scale
PublicationHydrodynamic cavitation is a promising technique for water disinfection. In the present paper, the disinfection characteristics of an advanced hydrodynamic cavitation reactor (ARHCR) in pilot scale were studied. The effects of various flow rates (1.4–2.6 m3/h) and rotational speeds (2600–4200 rpm) on the removal of Escherichia coli (E. coli) were revealed and analyzed. The variation regularities of the log reduction and reaction...
-
Effect of Functionalization of Reduced Graphene Oxide Coatings with Nitrogen and Sulfur Groups on Their Anti-Corrosion Properties
PublicationElectrophoretic production of anticorrosion carbonaceous coatings on copper could be successfully performed by anodic oxidation of negatively charged graphene platelets suspended in an aqueous solution. The various platelets were synthesized by Hummer’s method followed by a hydrothermal reduction in the presence of NH4SCN which was expected to substitute some parts of graphene structure with nitrogen and sulfur groups. X-ray photoelectron...
-
Effect of Thermal Treatment and Erosion Aggressiveness on Resistance of S235JR Steel to Cavitation and Slurry
PublicationS235JR steel is used in many applications, but its resistance to the erosion processes has been poorly studied. To investigate this resistance, cavitation, and slurry erosion tests were conducted. These tests were carried out at different erosion intensities, i.e., different flow rates in the cavitation tunnel with a system of barricades and different rotational speeds in the slurry pot. The steel was tested as-received and after...
-
Efficiency limit of excitonic photovoltaic cells under phosphor-based white LED illumination
PublicationThe limit of energy conversion of excitonic photovoltaic cells working under white light illumination generated by phosphor-based LED is analysed using the modified Giebink approach. Particularly, the impact of the optical energy gap and energy loss associated with the excitons dissociation at the heterojunction interface on power conversion efficiency of the device are discussed. From the results of our study it follows that the...
-
eFRADIR: An Enhanced FRAmework for DIsaster Resilience
PublicationThis paper focuses on how to increase the availability of a backbone network with minimal cost. In particular, the new framework focuses on resilience against natural disasters and is an evolution of the FRADIR/FRADIR-II framework. It targets three different directions, namely: network planning, failure modeling, and survivable routing. The steady state network planning is tackled by upgrading a sub-network (a set of links termed...
-
Electron-Induced Decomposition of Uracil-5-yl O-(N,N-dimethylsulfamate): Role of Methylation in Molecular Stability
PublicationThe incorporation of modified uracil derivatives into DNA leads to the formation of radical species that induce DNA damage. Molecules of this class have been suggested as radiosensitizers and are still under investigation. In this study, we present the results of dissociative electron attachment to uracil-5-yl O-(N,N-dimethylsulfamate) in the gas phase. We observed the formation of 10 fragment anions in the studied range of electron...
-
Elemental and water-insoluble organic carbon in Svalbard snow: a synthesis of observations during 2007–2018
PublicationLight-absorbing carbonaceous aerosols emitted by biomass or fossil fuel combustion can contribute to amplifying Arctic climate warming by lowering the albedo of snow. The Svalbard archipelago, being near to Europe and Russia, is particularly affected by these pollutants, and improved knowledge of their distribution in snow is needed to assess their impact. Here we present and synthesize new data obtained on Svalbard between 2007...
-
Employees With Autism Spectrum Disorders in the Digitized Work Environment: Perspectives for the Future
PublicationThe aim of this article is to examine the opportunities for employees with autism spectrum disorders (ASDs), arising from digital technology (DT) development. The author discusses assistive technology (AT) as a mean of creating a better work environment, making the digitized workplace more friendly for people with ASD. A possible solution of communication problems is replacing the interpersonal communication between employees with...
-
Estimation of structural stiffness with the use of Particle Swarm Optimization
PublicationThe paper presents the theoretical background and four applications examples of the new method for the estimation of support stiffness coefficients of complex structures modelled discretely (e.g. with the use of the Finite Element Model (FEM) method based on the modified Particle Swarm Optimization (PSO) algorithm. In real-life cases, exact values of the supports’ stiffness coefficients may change for various reasons...