Search
An investigation of microstructural basis for corrosion behavior of Al-CNT composites fabricated by SPS
Abstract
In this research effect of the addition of multi-wall carbon nanotubes (MWCNTs) as additive powder on microstructure and corrosion behavior of fabricated Al-CNT composites was studied. The aluminum powder and CNTs were mixed with high energy planetary ball-mill. It is observed that by increasing milling time, the uniformity of CNTs on aluminum matrix and consequently corrosion resistance of Al-CNT composite is increased. On the other hand, by increasing the volume percentage of CNTs, the uniformity of CNTs on aluminum matrix and corrosion resistance of fabricated Al-CNT composite is reduced. The value of polarization resistance, Rp, for fabricated composites with 2 % CNT is improved from 1.28 to 3.60 Ω/cm2 by increasing milling time. Also, the value of Rp for fabricated composites with 4 h milling time, is reduced from 3.60 to 2.76 Ω/cm2 by increasing the percentage of CNTs from 2 % up to 5 %. Moreover, Cyclic Polarization results showed that the pitting corrosion resistance improves by increasing milling time and deteriorates by increasing the percentage of CNTs. The electrochemical impedance spectroscopy (EIS) results showed that the corrosion mechanism of Al-CNT composites is a combination of uniform and pitting corrosion. Indeed, the CNTs act as preferred cathode regions and cause to formation of micro galvanic couples. The Al-2%CNT-4 h showed better uniformity and the highest corrosion resistance. The Al-5%CNT-2 h presented non-uniform distribution of CNTs and the lowest corrosion resistance.
Citations
-
6
CrossRef
-
0
Web of Science
-
5
Scopus
Authors (4)
-
Reza Ebrahimi
-
Masood Hasheminiasari
Cite as
Full text
full text is not available in portal
Keywords
Details
- Category:
- Articles
- Type:
- artykuły w czasopismach
- Published in:
-
DIAMOND AND RELATED MATERIALS
no. 140,
ISSN: 0925-9635 - Language:
- English
- Publication year:
- 2023
- Bibliographic description:
- Ekhlasiosgouei O., Ebrahimi R., Hasheminiasari M., Molin S.: An investigation of microstructural basis for corrosion behavior of Al-CNT composites fabricated by SPS// DIAMOND AND RELATED MATERIALS -Vol. 140,iss. Part B (2023), s.110422-
- DOI:
- Digital Object Identifier (open in new tab) 10.1016/j.diamond.2023.110422
- Sources of funding:
-
- Statutory activity/subsidy
- Verified by:
- Gdańsk University of Technology
seen 88 times
Recommended for you
A Quantitative Investigation of Dislocation Density in an Al Matrix Composite Produced by a Combination of Micro-/Macro-Rolling
- B. Sadeghi,
- A. Shabani,
- A. Heidarinejad
- + 3 authors
Optimization of biocorrosion resistance and mechanical properties of PM Ti–XAl–2Fe–3Cu alloys by response surface methodology
- M. Najafizadeh,
- M. Ghasempour-Mouziraji,
- M. Hosseinzadeh
- + 6 authors
Influence of CeO2 and TiO2 Particles on Physicochemical Properties of Composite Nickel Coatings Electrodeposited at Ambient Temperature
- I. Makarava,
- M. Esmaeili,
- D. Kharitonov
- + 5 authors
Effect of TiO2 Concentration on Microstructure and Properties of Composite Cu–Sn–TiO2 Coatings Obtained by Electrodeposition
- A. Kasach,
- D. Kharitonov,
- A. Paspelau
- + 4 authors