Search
Catalog Publications
Filters
total: 46755
displaying 1000 best results Help
Catalog Publications
2021
-
A 95-Year-Old Concrete Arch Bridge: From Materials Characterization to Structural Analysis
PublicationThe structural analysis of a 95-year-old concrete arch bridge located in Jagodnik (Poland) is performed in this paper, in order to check its behavior under today’s traffic loads. The mechanical properties of both the concrete and the reinforcement are investigated by testing cores and bar stubs extracted from the bridge. Structural analysis confirms that the bridge meets today’s load requirements in terms of bearing capacity, serviceability...
-
A comparison of muscle activity of the dominant and non-dominant side of the body during low versus high loaded bench press exercise performed to muscular failure
Publication -
A dynamic vehicle-bridge model based on the modal identification results of an existing EN57 train and bridge spans with non-ballasted tracks
PublicationThis paper addresses the methodology of the bridge-vehicle dynamic model definition based on the free response measurements of an existing train and existing bridge spans. In the case of the railway vehicle, the methodology uses the impulse excitations of a single car by means of the wedge method. In the case of the bridge spans, free responses are collected after the passages of trains. The global modal parameters (frequencies...
-
A general approach to study molecular fragmentation and energy redistribution after an ionizing event
PublicationWe propose to combine quantum chemical calculations, statistical mechanical methods, and photoionization and particle collision experiments to unravel the redistribution of internal energy of the furan cation and its dissociation pathways. This approach successfully reproduces the relative intensity of the different fragments as a function of the internal energy of the system in photoelectron–photoion coincidence experiments and...
-
A High-Arctic flow-through lake system hydrochemical changes: Revvatnet, southwestern Svalbard (years 2010–2018)
PublicationLake ecosystems are strongly coupled to features of their surrounding landscapes such as geomorphology, lithology, vegetation and hydrological characteristics. In the 2010–2018 summer seasons, we investigated an Arctic flow-through lake system Revvatnet, located in the vicinity of the coastal zone of Hornsund fjord in Svalbard, characterising its hydrological properties and the chemical composition of its waters. The lake system...
-
A hyperelastic model for soils with stress-induced and inherent anisotropy
PublicationIn this paper, modelling of the superposition of stress-induced and inherent anisotropy of soil small strain stiffness is8presented in the framework of hyperelasticity. A simple hyperelastic model, capable of reproducing variable stress-induced9anisotropy of stiffness, is extended by replacement of the stress invariant with mixed stress–microstructure invariant to10introduce constant inherent cross-anisotropic component. A convenient...
-
A measurement method for lossy capacitive relative humidity sensors based on a direct sensor-to-microcontroller interface circuit
PublicationA new time-domain measurement method for determining the capacitance and resistance values of lossy relative humidity capacitive sensors is presented. The method is based on a direct sensor-to-microcontroller interface for microcontrollers with internal analog comparators and timers. The interface circuit consists only of four reference resistors (two reference resistors if a microcontroller includes a voltage reference source),...
-
A Microwave Sensor with Operating Band Selection to Detect Rotation and Proximity in the Rapid Prototyping Industry
PublicationThis paper presents a novel sensor for detecting and measuring angular rotation and proximity, intended for rapid prototyping machines. The sensor is based on a complementary split-ring resonator (CSRR) driven by a conductor-backed coplanar waveguide. The sensor has a planar topology, which makes it simple and cost-effective to produce and accurate in measuring both physical quantities. The sensor has two components, a rotor, and...
-
A Model-Order Reduction Approach for Electromagnetic Problems With Nonaffine Frequency Dependence
PublicationThe aim of this paper is to present a novel model-order reduction (MOR) technique for the efcient frequency-domain nite-element method (FEM) simulation of microwave components. It is based on the standard reduced-basis method, but the subsequent expansion frequency points are selected following the so-called sparsied greedy strategy. This feature makes it especially useful to perform a fast-frequency sweep of problems that lead...
-
A new 1-nitro-9-aminoacridine derivative targeting yeast topoisomerase II able to overcome fluconazole-resistance
PublicationFungal resistance remains a significant threat and a leading cause of death worldwide. Thus, overcoming microbial infections have again become a serious clinical problem. Although acridine derivatives are widely analyzed as anticancer agents, only a few reports have demonstrated their antifungal activity. In an effort to develop biologically active antifungals, twelve novel C-857 (9-(2′ -hydroxyethylamino)-1-nitroacridine) and...
-
A New Approach to the PWM Modulation for the Multiphase Matrix Converters Supplying Loads with Open-End Winding.
PublicationThis article presents three variants of the Pulse Width Modulation (PWM) for the Double Square Multiphase type Conventional Matrix Converters (DSM-CMC) supplying loads with the open-end winding. The first variant of PWM offers the ability to obtain zero value of the common-mode voltage at the load's terminals and applies only six switches within the modulation period. The second proposal archives for less Total Harmonic Distortion...
-
A new multi-process collaborative architecture for time series classification
PublicationTime series classification (TSC) is the problem of categorizing time series data by using machine learning techniques. Its applications vary from cybersecurity and health care to remote sensing and human activity recognition. In this paper, we propose a novel multi-process collaborative architecture for TSC. The propositioned method amalgamates multi-head convolutional neural networks and capsule mechanism. In addition to the discovery...
-
A novel approach exploiting properties of convolutional neural networks for vessel movement anomaly detection and classification
PublicationThe article concerns the automation of vessel movement anomaly detection for maritime and coastal traffic safety services. Deep Learning techniques, specifically Convolutional Neural Networks (CNNs), were used to solve this problem. Three variants of the datasets, containing samples of vessel traffic routes in relation to the prohibited area in the form of a grayscale image, were generated. 1458 convolutional neural networks with...
-
A Novel Versatile Decoupling Structure and Expedited Inverse-Model-Based Re-Design Procedure for Compact Single-and Dual-Band MIMO Antennas
PublicationMultiple-input multiple-output (MIMO) antennas are considered to be the key components of fifth generation (5G) mobile communications. One of the challenges pertinent to the design of highly integrated MIMO structures is to minimize the mutual coupling among the antenna elements. The latter arises from two sources, the coupling in the free space and the coupling currents propagating on a ground plane. In this paper, an array of...
-
A Qualitative Study on Non-functional Requirements in Agile Software Development
PublicationWidespread use of agile software development (ASD) methods can be observed nowadays. Non-functional requirements (NFRs) are often reported to be a problematic issue for agile projects, since ASD methods tend to neglect NFRs while focusing on incremental delivery of functional features. Despite that, only very few studies have explored the requirements engineering practices used in ASD and dedicated particularly to NFRs. Objective:...
-
A sense of security and freedom in a residential environment
PublicationThe article is based on the results of a survey carried out among students of architecture faculties in several countries, which examined the students’ knowledge of shaping the housing environment in such a way as to enable them to fulfil two basic and, at the same time, seemingly mutually exclusive psychological needs of a person: a sense of security and a sense of freedom. In examining these issues, particular emphasis was placed...
-
A Series-Inclined-Slot-Fed Circularly Polarized Antenna for 5G 28-GHz Applications
PublicationThis letter presents the design of a single-point-fed, geometrically simple circularly polarized (CP) antenna for 28 GHz Ka-band applications. The proposed antenna is based on a straight microstrip line printed on one side and coupled with the nearly square patches through a 45-degree inclined V-shape slot aperture on the other side. In order to generate circular polarization, the fundamental radiating mode is degenerated at a...
-
A Systematic Literature Review on Implementing Non-functional Requirements in Agile Software Development: Issues and Facilitating Practices
PublicationAgile Software Development methods have become a widespread approach used by the software industry. Non-functional requirements (NFRs) are often reported to be a problematic issue for such methods. We aimed to identify (within the context of Agile projects): (1) the issues (challenges and problems) reported as affecting the implementation of NFRs; and (2) practices that facilitate the successful implementation of NFRs. We conducted...
-
A technique of experiment aided virtual prototyping to obtain the best spindle speed during face milling of large-size structures
PublicationThe paper presents an original method concerning vibration suppression problem during milling of large-size and geometrically complicated workpieces with the use of novel way of selecting the spindle speed. This consists in repetitive simulations of the cutting process for subsequent values of the spindle speed, until the best vibration state of the workpiece is reached. An appropriate method of obtaining a computational model,...
-
A tight-binding model of a carbon nanotube interacting with TiO2 rutile (110) surface
Publication -
A variational approach of homogenization of piezoelectric composites towards piezoelectric and flexoelectric effective media
PublicationThe effective piezoelectric properties of heterogeneous materials are evaluated in the context of periodic homogenization, whereby a variational formulation is developed, articulated with the extended Hill macrohomogeneity condition. The entire set of homogenized piezoelectric moduli is obtained as the volumetric averages of the microscopic properties of the individual constituents weighted by the displacement and polarization...
-
Accumulation of volatile constituents in agar and bioreactor shoot cultures of Verbena officinalis L.
PublicationIn vitro shoot cultures of common vervain (Verbena officinalis L., Verbenaceae) were established and evaluated for essential oil content. The shoots were maintained as stationary microshoot culture, grown on Schenk–Hildebrandt medium supplemented with 9.84 µM of 2-isopentenyladenine and 1.0 µM of thidiazuron. The shoots were further adapted to grow in two temporary immersion bioreactors (RITA and Plantform), using Schenk–Hildebrandt...
-
Accurate Modeling of Frequency Selective Surfaces Using Fully-Connected Regression Model with Automated Architecture Determination and Parameter Selection Based on Bayesian Optimization
PublicationSurrogate modeling has become an important tool in the design of high-frequency structures. Although full-wave electromagnetic (EM) simulation tools provide an accurate account for the circuit characteristics and performance, they entail considerable computational expenditures. Replacing EM analysis by fast surrogates provides a way to accelerate the design procedures. Unfortunately, modeling of microwave passives is a challenging...
-
Advanced super-hydrophobic polymer-based porous absorbents for the treatment of oil-polluted water
PublicationThe threat of environmental pollution caused by spilled oil is rapidly increasing along with the expansion of oil exploration, the development of maritime activities and industrial growth. Oil spill incidents usually affect seriously the ecosystem and human life. Therefore, the treatment and recovery of the oil spill have been considered as an ultra-important issue to protect the environment and to minimize its negative impacts...
-
Aiming at methods’ wider adoption: Applicability determinants and metrics
PublicationNumerous computer science methods and techniques have been proposed by the scientific community. However, depending on the domain, only their minor fraction has met wider adoption. This paper brings attention to the concept of applicability - the notion that is well acknowledged in the scientific field but have not been analysed with respect to determinants, metrics and systematisation. The primary objective of the study was to...
-
Aktualne trendy i rekomendacje w zakresie usuwania mikrozanieczyszczeń należących do farmaceutyków i pestycydów ze ścieków komunalnych
PublicationMikrozanieczyszczenia, przede wszystkim pestycydy oraz farmaceutyki, zyskują coraz większe zainteresowanie zarówno ze strony środowiska naukowego, administracji publicznej, jak również międzynarodowych organizacji rządowych i pozarządowych. W ostatnich latach jest obserwowany stały wzrost stężeń mikrozanieczyszczeń zarówno w glebie, jak i środowisku wodnym. Szczególne zagrożenie płynące ze strony pestycydów i farmaceutyków wynika...
-
Aktywna Termografia Dynamiczna - przetwarzanie serii obrazów w diagnostyce medycznej
PublicationAktywna termografia dynamiczna (ATD) jest metodą obrazowania zmian temperatury na powierzchni badanego obiektu w czasie jako odpowiedź na zastosowane pobudzenie zewnętrzne (ogrzewanie lub chłodzenie). Celem badania jest określenie właściwości obiektu w czasie trwania termicznych procesów przejściowych, takich jak grzanie lub chłodzenie. Obiekt badany jest pobudzany sygnałem cieplnym (zewnętrznie) lub farmakologicznie (wewnętrznie)....
-
AMO perspectives on the well-being of neurodivergent human capital
PublicationExisting management research and management practices frequently overlook the relationship between the above-average human capital of highly functioning neurodivergent employees, their subjective well-being in the workplace and performance outcomes. This paper calls for greater attention to the hidden human capital associated with neurodiversity by mainstreaming implementation of neurodiversity-friendly policies and practices. Drawing...
-
An analysis of wind conditions at pedestrian level in the selected types of multi-family housing developments
PublicationThe following article addresses the issue of wind conditions around urban building development at pedestrian level. Factors that depend on those issues include wind comfort and air quality within urbanized spaces. The conditions specific of cities located in a temperate climate zone have been taken into account. The article is intended to identify aerodynamic phenomena characteristic of the three basic types of multi-family building...
-
An efficient and robust method for predicting asphalt concrete dynamic modulus
Publication -
Analiza bibliometryczna w badaniach dotyczących prognozowania upadłości przedsiębiorstw w Polsce
PublicationCelem opracowania jest ukazanie obrazu piśmiennictwa poświęconego zagadnieniom prognozowania upadłości przedsiębiorstw w Polsce. Jako metodę badawczą zastosowano analizę bibliometryczną. Do analizy wykorzystano bazę Google Scholar oraz narzędzie Publish or Perish 7. Okresem badań objęto lata 1995– 2019. Jako frazy do wyszukiwania publikacji zastosowano: „prognozowanie upadłości”, „prognozowanie zagrożenia finansowego”, „systemy...
-
Analiza danych pomiarowych na potrzeby obrazowania optyczną tomografią koherentną
PublicationW rozdziale omówiono wybrane aspekty związane z analizą danych pomiarowych na potrzeby obrazowania metodą optycznej tomografii koherentnej. Przedstawiono podstawowe zależności umożliwiające obrazowanie tkanek na podstawie analizy promieniowania wstecznie rozproszonego, mierzonego przez systemy OCT pracujące w dziedzinie czasu (TD-OCT) lub w dziedzinie częstotliwości (FD-OCT). Pokazano, że wykorzystując zaawansowane przetwarzanie...
-
Analysis
PublicationNew food products and diverse formulations containing the regulated steviol glycoside(s) as well as Stevia extracts or Stevia leaves have been brought on the global market. The upcoming multitude of such food products, but also their falsification and adulteration, does have impact on food analysis. Robust high-throughput methods that cope with different food matrices are required for food control to ensure food safety. The analysis...
-
Analysis of 5-Hydroxymethyluracil Levels Using Flow Cytometry
Publication -
Anticancer Properties of Amino Acid and Peptide Derivatives of Mycophenolic Acid
PublicationBackground: Although Mycophenolic Acid (MPA) is applied as prodrugs in clinic as an immunosuppressant, it also possesses anticancer activity. MPA acts as Inosine-5’-Monophosphate Dehydrogenase (IMPDH) inhibitor, where the carboxylic group at the end of the side chain interacts with Ser 276 of the enzyme via hydrogen bonds. Therefore, MPA derivatives with other polar groups indicated high inhibition too. On the other hand, potent...
-
Antifungal Activity of Capridine β as a Consequence of Its Biotransformation into Metabolite Affecting Yeast Topoisomerase II Activity
PublicationIn the last few years,increasing importance is attached to problems caused by fungal pathogens. Current methods of preventing fungal infections remain unsatisfactory. There are several antifungal compounds whichare highly effective in some cases, however, they have limitations in usage: Nephrotoxicity and other adverse effects. In addition, the frequent use of available fungistatic drugs promotes drug resistance....
-
Application analysis of a hybrid solid oxide fuel cell-gas turbine system for marine power plants
PublicationThe results of theoretical studies of the possibilities of using hybrid solid oxide fuel cell–gas turbine (SOFC-GT) systems for marine power plants are presented. A 500 kW auxiliary marine power plant scheme using stacks of SOFCs in combination with a regenerative gas turbine operating with over-expansion based on our recent patent application is proposed. The results of mathematical modelling showed the opportunity to obtain a...
-
Application of cold atmospheric pressure plasmas for high-throughput production of safe-to-consume beetroot juice with improved nutritional quality
Publication -
Application of discrete wavelet transform in seismic nonlinear analysis of soil–structure interaction problems
PublicationSimulation of soil-structure interaction (SSI) effects is a time-consuming and costly process. However, ignoring the influence of SSI on structural response may lead to inaccurate results, especially in the case of seismic nonlinear analysis. In this paper, wavelet transform methodology has been utilized for investigation of the seismic response of soil-structure systems. For this purpose, different storey outrigger braced buildings...
-
Applications of Additively Manufactured Tools in Abrasive Machining—A Literature Review
PublicationHigh requirements imposed by the competitive industrial environment determine the development directions of applied manufacturing methods. 3D printing technology, also known as additive manufacturing (AM), currently being one of the most dynamically developing production methods, is increasingly used in many different areas of industry. Nowadays, apart from the possibility of making prototypes of future products, AM is also used...
-
Are deep eutectic solvents useful in chromatography? A short review
PublicationA literature update has been done concerning Deep Eutectic Solvents (DES) use in chromatography applications. The literature survey was based on the period from 2010 till 2020 and manuscripts reported in the data bases Web of Science and Scopus. The use of DES as mobile phase and mobile phase additives, stationary phases and solid phase modifiers and the use of DES as reaction solvents for chromatography use, were evaluated. Emphasis...
-
Arithmetic Loophole in Bell's Theorem: Overlooked Threat to Entangled-State Quantum Cryptography
PublicationBell’s theorem is supposed to exclude all local hidden-variable models of quantum correlations. However,an explicit counterexample shows that a new class of local realistic models, based on generalized arith-metic and calculus, can exactly reconstruct rotationally symmetric quantum probabilities typical oftwo-electron singlet states. Observable probabilities are consistent with the usual arithmetic employedby macroscopic observers...
-
Assessment and design of greener deep eutectic solvents – A multicriteria decision analysis
PublicationDeep eutectic solvents (DES) are often considered as green solvents because of their properties, such as negligible vapor pressure, biodegradability, low toxicity or natural origin of their components. Due to the fact that DES are cheaper than ionic liquids, they have gained many applications in a short period of time. However, claims about their greenness sometimes seem to be exaggerated. Especially, bearing in mind lots of data...
-
Assessment of diversity and composition of bacterial community in Sludge Treatment Reed Bed systems
PublicationDue to their low emission of odours and lack of the need to apply additional chemical agents, sludge treatment reed beds (STRBs) constitute an economically feasible and eco-friendly approach to sewage sludge management. Correctly designed and operated STRBs ensure effective reduction of the dry matter content coupled with the mineralisation of organic compounds. Successful operation of STRBs relies on complex interactions between...
-
Assessment of the devulcanization process of EPDM waste from roofing systems by combined thermomechanical/microwave procedures
PublicationEthylene-propylene-diene rubber (EPDM) is a elastomer widely used in common industrial applications. EPDM can be shaped into sheets and employed as isolating material for roofing systems. In this study, scraps of EPDM from commercial, industrial and residential roofing systems were treated by combined thermo-mechanical and microwave devulcanization processes including peroxide of benzoyl (BPO). The devulcanized EPDM (Dev-EPDM)...
-
Assessment of the devulcanization process of EPDM waste from roofing systems by combined thermomechanical/microwave procedures
PublicationEthylene-propylene-diene rubber (EPDM) is a elastomer widely used in common industrial applications. EPDM can be shaped into sheets and employed as isolating material for roofing systems. In this study, scraps of EPDM from commercial, industrial and residential roofing systems were treated by combined thermo-mechanical and microwave devulcanization processes including peroxide of benzoyl (BPO). The devulcanized EPDM (Dev-EPDM)...
-
ASSESSMENT OF VOLATILE ORGANIC COMPOUNDS EMISSIONS FROM RECYCLED LOW-DENSITY POLYETHYLENE STREAMS
PublicationThe recycling of plastics is currently one of the most significant industrial challenges. Due to the enormous amounts of plastic wastes generated by various industry branches, it is essential to look for the potential methods of their utilization. Nevertheless, it should not be forgotten that recycled plastics are not pure materials, and they still may show an unfavorable environmental impact. They may contain different contaminants...
-
Atmospheric deposition of microplastics in the coastal zone: Characteristics and relationship with meteorological factors
PublicationThe quantitative and qualitative compositions of microplastics (MPs) deposited from the atmosphere in the coastal zone were analysed. Moreover, links between MP deposition and meteorological factors (air humidity, wind speed, precipitation height, and air mass trajectories) were investigated
-
Autonomous Ship Utility Model Parameter Estimation Utilising Extended Kalman Filter
PublicationIn this paper, a problem of autonomous ship utility model identification for control purposes is considered. In particular, the problem is formulated in terms of model parameter estimation (one-step-ahead prediction). This is a complex task due to lack of measurements of the parameter values, their time-variability and structural uncertainty introduced by the available models. In this work, authors consider and compare two utility...
-
Bariery rozwoju bioekonomii w Polsce
PublicationW Polsce sytuacja ponownego wykorzystania odpadu celem produkcji nowych produktów nie jest obecnie do końca uregulowana prawnie. Nie obserwuje się wielu dobrych praktyk w przedsiębiorstwach. Wartościowe odpady poprodukcyjne są wykorzystywane na cele energetyczne bądź jako nawóz dla roślin lub pasza dla zwierząt. W celu zlokalizowania barier w rozwoju bioekonomii przeprowadzono wywiady z osobami bezpośrednio związanymi z kwestiami...
-
Barokowy romantyzm Słowackiego
Publication -
Baseline-free debonding detection in reinforced concrete structures by elastic wave propagation
PublicationThe article presents the results of the numerical and experimental analysis concerning wave propagation in reinforced concrete (RC) beams with various extent of debonding between the steel rod and concrete cover. The main aim of the paper was to consider the unsolved research gaps, which considerably limit the application of wave-based methods in practice. The propagation of the flexural wave modes excited and registered on the...
-
Bee Bread Exhibits Higher Antimicrobial Potential Compared to Bee Pollen
PublicationThis study aimed at investigation of the antimicrobial potential of ethanolic extracts of bee bread (BB) and bee pollen (BP) and suspensions of these products in MHB (Mueller Hinton Broth). We covered 30 samples of BP and 19 samples of BB harvested in Polish apiaries. Slightly lower activity was observed against Gram-negative bacteria compared to Gram-positive staphylococci. BB extracts exhibited higher inhibitory potential with...
-
Behavior of residual current devices at frequencies up to 50 kHz
PublicationThe use of residual current devices (RCDs) is obligatory in many types of low-voltage circuits. They are devices that ensure protection against electric shock in the case of indirect contact and may ensure additional protection in the case of direct contact. For the latter purpose of protection, only RCDs of a rated residual operating current not exceeding 30 mA are suitable. Unfortunately, modem current-using equipment supplied...
-
Bending analysis of functionally graded nanoplates based on a higher-order shear deformation theory using dynamic relaxation method
PublicationIn this paper, bending analysis of rectangular functionally graded (FG) nanoplates under a uniform transverse load has been considered based on the modified couple stress theory. Using Hamilton’s principle, governing equations are derived based on a higher-order shear deformation theory (HSDT). The set of coupled equations are solved using the dynamic relaxation (DR) method combined with finite difference (FD) discretization technique...
-
Bennet
Publication.
-
Bifractal receiver operating characteristic curves: a formula for generating receiver operating characteristic curves in credit-scoring contexts
PublicationThis paper formulates a mathematical model for generating receiver operating characteristic (ROC) curves without underlying data. Credit scoring practitioners know that the Gini coefficient usually drops if it is only calculated on cases above the cutoff. This fact is not a mathematical necessity, however, as it is theoretically possible to get an ROC curve that keeps the same Gini coefficient no matter how big a share of lowest...
-
Biological Effects of Cold Atmospheric Pressure Plasma on Skin Cancer
Publication -
Biomass-Derived Nitrogen Functionalized Carbon Nanodots and Their Anti-Biofouling Properties
PublicationThe prevalence of the antibiotic resistant bacteria remains a global issue. Cheap, sustainable and multifunctional antibacterial membranes are at the forefront of filtrating materials capable of treating multiple flow streams, such as water cleansing treatments. Carbon nanomaterials are particularly interesting objects shown to enhance antibacterial properties of composite materials. In this article, amino-functionalized, photoluminescent...
-
Block graphs with large paired domination multisubdivision number
PublicationThe paired domination multisubdivision number of a nonempty graph G, denoted by msdpr(G), is the smallest positive integer k such that there exists an edge which must be subdivided k times to increase the paired domination number of G. It is known that msdpr(G) ≤ 4 for all graphs G. We characterize block graphs with msdpr(G) = 4.
-
Bypass kolejowy dla wiaduktu łukowego i kratownicowego w ciągu modernizowanej linii kolejowej E59 na odcinku Wronki – Dobiegniew
PublicationW artykule przedstawiono realizacje bypassu kolejowego, zlokalizowanego nieopodal miejscowości Krzyż Wielkopolski w ciągu linii kolejowej E59 na skrzyżowaniu z linią kolejową 203. Wariantowa analiza kilku zaproponowanych rozwiązań wykazała, ze wykonstruowanie bypassu na czas prowadzenia prac modernizacyjnych pozwoli na utrzymanie ciągłości ruchu kolejowego, nie stworzy nadmiernych problemów podróżnym, a jednocześnie pozwoli na...
-
By-Products from Food Industry as a Promising Alternative for the Conventional Fillers for Wood–Polymer Composites
PublicationThe present paper describes the application of two types of food-industry by-products, brewers’ spent grain (BSG), and coffee silverskin (ŁK) as promising alternatives for the conventional beech wood flour (WF) for wood–polymer composites. The main goal was to investigate the impact of partial and complete WF substitution by BSG and ŁK on the processing, structure, physicochemical, mechanical, and thermal properties of resulting...
-
Carbon nanoarchitectures as high-performance electrodes for the electrochemical oxidation of landfill leachate
PublicationNanomaterials and assemblies of the aforementioned into complex architectures constitute an opportunity to design efficient and selective solutions to wide spread and emerging environmental issues. The limited disposal of organic matter in modern landfills generates extremely concentrated leachates characterised by high concentrations of refractory compounds. Conventional biochemical treatment methods are unsuitable, while advanced...
-
Carrefour
Publication.
-
Cascade Object Detection and Remote Sensing Object Detection Method Based on Trainable Activation Function
PublicationObject detection is an important process in surveillance system to locate objects and it is considered as major application in computer vision. The Convolution Neural Network (CNN) based models have been developed by many researchers for object detection to achieve higher performance. However, existing models have some limitations such as overfitting problem and lower efficiency in small object detection. Object detection in remote...
-
CFD Simulations and Tests of a Prototype Flow Control Valve
PublicationIn this paper a prototype of a flow control valve is described and numerically simulated. The flow control valve is used in hydraulic systems to maintain constant fluid flow despite changing loads of a receiver. The standard construction of this type of valves is modified mainly by eliminating the spring. The prototype consists the hydrostatically unloaded throttle valve and pressure ratio valve substituting pressure difference...
-
Chain Action - How Do Countries Add Value Through Digital Government?
PublicationThis study examineshow countries develop and benefit from Digital Government(DG).The literature proposes various conceptualizations of the value-adding logic of DG, but the benchmarking practice is not respondingto such proposals.For instance, the United Nations’E-Government Surveycombines the readiness and uptake indicatorsand failsto cover any impactindicators;thus,its diagnostic valueis limited. To overcome...
-
Challenges and opportunities related to the use of sewage sludge ash in cement-based building materials – A review
PublicationDue to the increasingly demanding legal regulations, regarding both sewage sludge (SS) and solid residues obtained during its thermal utilization processes, new solutions to limit their negative impact on the environment are sought. One approach that eliminates the risk of sewage sludge ash (SSA) is its use in cement building materials. The article contains a detailed literature review regarding the use of SSA in mortars and concretes,...
-
Challenges in coupling atmospheric electricity with biological systems
Publication -
Changes in Muscle Activity Imbalance of the Lower Limbs Following 3 Weeks of Supplementary Body-Weight Unilateral Training
Publication -
Characterization of aggregate interlocking in hot mix asphalt by mechanistic performance tests
Publication -
Characterization of Arctic Driftwood as Naturally Modified Material. Part 1: Machinability
PublicationArctic driftwood has reached the coast of Iceland for centuries. This material was used by the inhabitants of the island as a building material for houses, boats, churches and pasture fences. Nowadays, the driftwood is used in the furniture industry, for the finishing of internal and external walls of buildings and also by artists. The properties of driftwood differ to that of original resource due the long-term effects of exposure...
-
Characterization of fracture process in polyolefin fibre-reinforced concrete using ultrasonic waves and digital image correlation
PublicationThis study explores the monitoring of the fracture process in concrete beams and aims to characterize the evolution of damage in polyolefin fibre-reinforced concrete beams by utilizing the integrated application of two measurement techniques, digital image correlation and ultrasonic testing. The interpretation of registered wave time histories data was provided by the calculation of the magnitude-phase-composite metrics. An efficient...
-
Characterization of herbal teas containing lime flowers – Tiliae flos by HPTLC method with chemometric analysis
PublicationLinden trees are a source of food products called lime flowers (Tiliae flos), traditionally used in the form of infusion for the treatment of feverish colds and coughs. Lime flowers should include flowers of Tilia cordata Mill, T.x europaea L., and T. platyphyllos Scop. or a mixture of these. The aim of current research was to establish a fast, sensitive HPTLC (high-performance thin-layer chromatography) method that would allow...
-
Chemical, Physical, and Mechanical Properties of 95-Year-Old Concrete Built-In Arch Bridge
PublicationThis research aimed to determine the durability and strength of an old concrete built-in arch bridge based on selected mechanical, physical, and chemical properties of the concrete. The bridge was erected in 1925 and is located in Jagodnik (northern Poland). Cylindrical specimens were taken from the side ribs connected to the top plate using a concrete core borehole diamond drill machine. The properties of the old concrete were...
-
Chemical surface etching methods for ground tire rubber as sustainable approach for environmentally-friendly composites development– a review
PublicationGround tire rubber (GTR) has been used as a sustainable low-cost modifier in various composites. However, due to the hydrophobic nature of GTR, it is in compatible with most matrices and results in deterioration in both mechanical and physical properties of composites. This necessitates pre-modification of the powdered rubber to improve the interfacial bonding at the rubber-matric interface. The most common GTR modification research...
-
Coffee Silverskin as a Multifunctional Waste Filler for High-Density Polyethylene Green Composites
PublicationThis work aims to describe the coffee silverskin effect as a lignocellulosic waste filler for high-density polyethylene (HDPE) composites development. The main task was to determine various modification effects resulting from the complex chemical composition of coffee silverskin containing compounds with potential antioxidative properties, including caffeine, polyphenols, tannins, or melanoidins. The processing, thermal, physicochemical,...
-
Coffee silverskin as a potential bio-based antioxidant for polymer materials: Brief review
PublicationCoffee silverskin is one of the by-products generated by the coffee industry. Although it is not the most burdensome one, because it stands only for ~4.2 wt % of coffee, it seems like an auspicious raw material for industrial processes. Coffee silverskin is characterized by a relatively low moisture content of ~5–7%, so it often does not require quite energy-consuming drying processes. The chemical composition of coffee silverskin,...
-
Coin
Publication.
-
Combination of hydrodynamic cavitation and SR-AOPs for simultaneous degradation of BTEX in water
PublicationHydrodynamic cavitation (HC) is an emerging technology gaining interest in water treatment for use in elimination of a wide range of organic pollutants. The energy released during cavitation phenomenon has number of applications and, particularly, it can be utilized for activation of persulfate (PS) and peroxymonosulfate (PMS). In the present study, hybrid techniques: HC combined with persulfates – HC-PS and HC-PMS were tested...
-
Company versus consumer performance: does brand community identification foster brand loyalty and the consumer’s personal brand?
PublicationThis study investigates the effect of community identification in building brand loyalty (attitudinal and behavioural) and a personal brand via social networks. The proposed model explained the main community identification antecedents and how identification can lead to enhanced company and consumer performance. This study adopts the theoretical lens of uses and gratifications theory and identifies three motivational drivers of...
-
Comparative Study of the Reinforcement Type Effect on the Thermomechanical Properties and Burning of Epoxy-Based Composites
PublicationAramid (AF), glass (GF), carbon (CF), basalt (BF), and flax (FF) fibers in the form of fabrics were used to produce the composites by hand-lay up method. The use of fabrics of similar grammage for composites’ manufacturing allowed for a comprehensive comparison of the properties of the final products. The most important task was to prepare a complex setup of mechanical and thermomechanical properties, supplemented by fire behavior...
-
Comparison of Absorbed and Intercepted Fractions of PAR for Individual Trees Based on Radiative Transfer Model Simulations
PublicationThe fraction of absorbed photosynthetically active radiation (fAPAR) is a key parameter for estimating the gross primary production (GPP) of trees. For continuous, dense forest canopies, fAPAR, is often equated with the intercepted fraction, fIPAR. This assumption is not valid for individual trees in urban environments or parkland settings where the canopy is sparse and there are well-defined tree crown boundaries. Here, the distinction...
-
Comparison of nitrogen and VFA removal pathways in autotrophic and organotrophic anammox reactors
PublicationOrganotrophic anammox is a promising process for treating both nitrogen and organic containing wastewater than that of the traditional autotrophic anammox for sole nitrogen removal. However pathways of nitrogen removal particularly at metagenomic level in both processes are still unknown. Here we report, metabolic pathways of nitrogen removal in two lab-scale sequencing batch reactors (SBR), one autotrophic and another organotrophic...
-
Complexes of silanethiolate ligands: Synthesis, structure, properties and application
PublicationThe purposeful syntheses of silanethiolate complexes started approximately in the mid-eighties of the 20th century but no summary of the synthetic efforts has been reported till now. The synthetic methods and the resulting complexes have some common features, which are emphasized throughout the review. Thereby specific difficulties during synthesis are outlined and the structures, properties and possible applications of the resulting...
-
Comprehensive thermodynamic analysis of the CAES system coupled with the underground thermal energy storage taking into account global, central and local level of energy conversion
PublicationA key aspect of CAES is the optimal configuration of the thermodynamic cycle. In this paper, the situation of cooperation between the current conventional power plants and wind farms is analyzed, and then, based on thermodynamic models, the process of storing thermal and electrical energy in the CAES system coupled with a heat storage and recovery is developed. Therefore, three levels can be distinguished, namely: the global level...
-
Computational analysis of an infinite magneto-thermoelastic solid periodically dispersed with varying heat flow based on non-local Moore–Gibson–Thompson approach
PublicationIn this investigation, a computational analysis is conducted to study a magneto-thermoelastic problem for an isotropic perfectly conducting half-space medium. The medium is subjected to a periodic heat flow in the presence of a continuous longitude magnetic field. Based on Moore–Gibson–Thompson equation, a new generalized model has been investigated to address the considered problem. The introduced model can be formulated by combining...
-
Computational and experimental evaluation of view out according to European Standard EN17037.
PublicationThis paper presents an experimental evaluation of view out based on EN17037:2018 Daylight in Buildings within an educational building. The primary motivation to conduct the research was an introduction of a view out appraisal criteria by the mentioned standard. The study gives insights into the following: (i) the use of computational evaluation of an outside view according to the EN17037 criteria (ii) the use of the direct simultaneous...
-
Computational Selectivity Assessment of Protease Inhibitors against SARS-CoV-2
Publication -
Concept of managing quality in baking industry, in vector representation
PublicationThe author introduced an innovative metrisable method of describing a manufacturing process. The idea of vector structure of a manufacturing process allows to formulate quantitative relations between the activity of input streams, elements of product quality, and measurable effects of losses. The structure was basis for the formulation of the concept of the process of managing product quality in the baking industry in a vector...
-
Contact with coupled adhesion and friction: Computational framework, applications, and new insights
PublicationContact involving soft materials often combines dry adhesion, sliding friction, and large deformations. At the local level, these three aspects are rarely captured simultaneously, but included in the theoretical models by Mergel et al., (2019). We here develop a corresponding finite element framework that captures 3D finite-strain contact of two deformable bodies. This framework is suitable to investigate sliding friction even...
-
Copper and copper-manganese 1D coordination polymers: Synthesis optimization, crystal structure and preliminary studies as catalysts for Baylis–Hillman reactions
PublicationThis work reports the influence of experimental parameters (pH and counter-ion) in the synthesis of the 1D coordination polymer [Cu(IDA)(H2O)2]n (IDA = iminodiacetate), named here Cu-IDA. Copper-manganese bimetallic coordination polymers were also obtained by isomorphic replacement into Cu-IDA structure, with different molar ratio of Cu2+ and Mn2+ ions, denoted here as Cu/Mn-IDA (0.9/0.1; 0.7/0.3 and 0.5/0.5). New coordination...
-
Copper(I) halide cluster-based coordination polymers modulated by chiral ditopic dithiodianthranilide ligands: synthesis, crystal structure and photoluminescence
PublicationReaction of copper(I) halides with chiral dithiodianthranilidesmdtaandbdtaafforded polymeric complexeswhere polynuclear CuX clusters were linked together by ditopic bridging ligands into 1D chains or 2D layerstructures. In the case of racemic ligands double stranded chain polymers were formed where the Cu4X4(X = I or Br) cores are connected by enantiomeric pairs of the ditopic ligands. In contrast, a homochiralmdtaligand created...
-
Coupling between Blood Pressure and Subarachnoid Space Width Oscillations during Slow Breathing
PublicationThe precise mechanisms connecting the cardiovascular system and the cerebrospinal fluid (CSF) are not well understood in detail. This paper investigates the couplings between the cardiac and respiratory components, as extracted from blood pressure (BP) signals and oscillations of the subarachnoid space width (SAS), collected during slow ventilation and ventilation against inspiration resistance. The experiment was performed on...
-
Coupling transformation of carbon, nitrogen and sulfur in a long-term operated full-scale constructed wetland
PublicationThe coupling transformation of carbon, nitrogen and sulfur compounds has been studied in lab-scale and pilot-scale constructed wetlands (CWs), but few studies investigated full-scale CW. In this study, we used batch experiments to investigate the potentials of carbon, nitrogen and sulfur transformation in a long-term operated, full-scale horizontal subsurface flow wetland. The sediments collected from the HSFW were incubated for...
-
Creating Shared Value by the University
PublicationPurpose Works that link creating shared value (CSV) with the university are arising, and there is a hope for a great future of this combination. The main problem with these works is that they are based on the wrong assumptions of what CSV is. The aim of the paper is to properly explain the concept of CSV and match it with university social responsibility (USR) at a strategic level. Design/methodology/approach A literature review...
-
Curved Surface Minijet Impingement Phenomena Analysed with ζ-f Turbulence Model
PublicationThe jet impingement phenomenon plays an important role among the heat transfer intensification methods. Very often its application and analyses refer to simple flat surfaces, while there is a lack of information in the literature for cases addressing curved surfaces. In the present work, the single jet impingement on the non-flat (concave and convex) surface is studied for a wide range of geometries, which originate from the mini-jet...
-
Damage detection in plates based on Lamb wavefront shape reconstruction
PublicationMany of the current studies in the area of damage detection using elastic wave propagation are based on deploying sensor networks with a large number of piezoelectric transducers to detect small-size cracks. A major limitation of these studies is that cracks are usually larger and have different shapes in real cases. Moreover, using a large number of sensing nodes for damage detection is both costly and computationally intensive....
-
Data Intelligence and Cognitive Informatics
PublicationThis book discusses new cognitive informatics tools, algorithms and methods that mimic the mechanisms of the human brain which lead to an impending revolution in understating a large amount of data generated by various smart applications. The book is a collection of peer-reviewed best selected research papers presented at the International Conference on Data Intelligence and Cognitive Informatics (ICDICI 2020), organized by SCAD...
-
Deep eutectic solvents based assay for extraction and determination of zinc in fish and eel samples using FAAS
PublicationA new assay based on effective (high recovery) extraction by means of deep eutectic solvents (DESs) was developed for ppb level determination of zinc in fishes and eel samples. Choline chloride and Phenol in a 1:2 M ratio was selected as optimal DES-based extraction solvent. 8-Hydroxy quinoline was used as a chelating agent for zinc ions. The optimized conditions were found at pH value of 8, ligand concentration of 10 mg/L, THF...