Filters
total: 2637
filtered: 2078
displaying 1000 best results Help
Search results for: common-mode voltage
-
Reactive deposition of TiNx layers in a DC-magnetron discharge
PublicationTiNx layers have been deposited in 'balanced mode' and 'unbalanced mode' of a reactive DC-magnetron plasma (carrier gas argon, reactive gas nitrogen) under different conditions. Discharge power and reactive gas flow have been varied. The layers have been examined by X-ray photoelectron spectroscopy (XPS), X-ray reflectometry (XR), and spectroscopic ellipsometry (SE). The results of the layer analyses were combined with plasma investigations...
-
Application of boron-doped diamond film and ZnO layer in the Fabry-Pérot interferometer
PublicationIn this article there have been presented the use of boron-doped diamond films for sensor applications. The low-finesse Fabry-Pérot interferometer working in the reflective mode has been implemented. Two kinds of reflective layers have been elaborated: boron-doped diamond thin films and zinc-oxide (ZnO) layer. Thin ZnO layers were deposited by Atomic Layer Deposition (ALD) on the face of a standard telecommunication single-mode...
-
Performance analysis and optimization of the Radio Link Control layer in UMTS.
PublicationRLC (Radio Link Control) jest jedną z podwarstw warstwy 2 stosu radiowego systemu UMTS. RLC wspiera trzy podstawowe tryby działania: przezroczysty (Transparent Mode, TM), bezpotwierdzeniowy (Unacknowledged Mode, UM) oraz potwierdzeniowy (Acknowledged Mode, AM). Wydajność RLC AM jest mocno uzależniona od konfiguracji RLC oraz jej zdolności do dynamicznej rekonfiguracji, odzwierciedlającej zmiany w przesyłanym ruchu oraz w jakości...
-
A robust 18-pulse diode rectifier with coupled reactors
PublicationThe article presents the principle of operation and selected results of simulation and laboratory tests of the 18-pulse rectifier system with coupled reactors and small series active power filter. The presented system makes it possible to reduce, especially in distribution supply networks, undesired higher current harmonics. The 18-pulse nature of operation of the rectifier is reached using a set of coupled three-phase network...
-
A method of earth fault loop impedance measurement without unwanted tripping of RCDs
PublicationIn low-voltage networks, earth fault loop impedance (EFLI) measurement is the basis for assessing the effectiveness of automatic disconnection of supply. Such a measurement is performed during initial and periodical verification, especially in a TN low-voltage network. Nowadays, due to widespread application of residual current devices (RCDs), such test is difficult in many circuits because RCDs operate during the test. In this...
-
Uncertainty estimation of loop impedance measurement determined by the vector method
PublicationThis article presents a detailed analysis of uncertainty estimation of loop impedance measurement determined by the vector method. The analysis includes the following estimates: resistance variance, voltage variance and time measurement variance. This paper presents a methodology for estimating the combined standard uncertainty of loop impedance by the vector method. The vector method allows to determine loop impedance based on...
-
Ancillary services to grids provided with distributed generation
PublicationThe paper introduces system for utilization of the customer-side generated energy. Additionally system can secure some ancillary services to grids. Those services include: current active filtering, load voltage stabilization and in case of grid voltage faults - uninterruptible load supplying (possible with energy storage device). Presented experimental results confirm flexibility of this arrangement in processes of power delivery...
-
Measurement methods for assessing insulation condition of underground pipelines
PublicationThe paper discusses the most frequently applied measurement methods for assessing the quality of external insulation along pipelines and detecting defect locations in the protective coating. The quality of coating along a given pipeline section under investigation is assessed by determining unitary resistance of the coating, which is calculated on the basis of measurement results obtained along a pipeline subjected to cathodic...
-
High Performance Control of AC Drives with Matlab/ Simulink
PublicationExplore this indispensable update to a popular graduate text on electric drive techniques and the latest converters used in industry. The Second Edition of High Performance Control of AC Drives with Matlab®/Simulink delivers an updated and thorough overview of topics central to the understanding of AC motor drive systems. The book includes new material on medium voltage drives, covering state-of-the-art technologies and challenges...
-
Application of infrared thermoography to non-contact testing of varistors
PublicationTesting of varistors using thermography was carried out in order to assess their protective properties against possible overvoltage phenomena in the form of high-level voltage surges. An advantage of the thermography technique is non-contact temperature measurement. It was proposed to assess the properties of varistors workingin electronic devices as protective elements, on the basis of estimating temperature increments on varist...
-
Sensorless Fault Detection of Induction Motor with Inverter Output Filter
PublicationThe paper presents the problem of monitoring and fault detection of a sensorless voltage inverter fed squirrel cage induction motor with LC filter. The detection is based on load torque estimation of the investigated torque transmission system. The load torque is calculated besides the computation of other variables that are mandatory for sensorless drive operation such as rotor flux and speed. The implemented LC filter smooths...
-
Current Source Inverter Fed Drive
PublicationThis book covers three-phase and multiphase (more than three-phase) motor drives including their control and practical problems faced in the field (e.g., adding LC filters in the output of a feeding converter), are considered. The new edition contains links to Matlab®/Simulink models and PowerPoint slides ideal for teaching and understanding the material contained within the book. Readers will also benefit from the inclusion of: A...
-
Vibrational excitation of acetylene by positron impact
PublicationVibrationally inelastic quantum calculations are carried out at low collision energies for the scattering of a beam of positrons off acetylene gaseous molecules. The normal mode analysis is assumed to be valid and the relative fluxes into the C–C and C–H symmetric vibrational modes are computed within a Body-Fixed (BF) formulation of the dynamics by solving the relevant vibrational Coupled Channels (VCC) equations. The clear dominance...
-
Extendable Safety and Security Ontology
PublicationSecurity plays an increasingly important role in our everyday life, and research and users of computer systems point out that the need arises for a common, formalised model capable of integrating different solutions. In this paper we show that an ontology can be designed and created in a way that will make it suitable for interoperability and integration. A security and safety ontology and the methodology for creating a common...
-
Electromagnetic-based derivation of fractional-order circuit theory
PublicationIn this paper, foundations of the fractional-order circuit theory are revisited. Although many papers have been devoted to fractional-order modelling of electrical circuits, there are relatively few foundations for such an approach. Therefore, we derive fractional-order lumped-element equations for capacitors, inductors and resistors, as well as Kirchhoff’s voltage and current laws using quasi-static approximations of fractional-order...
-
THE UNSUSTAINABILITY OF PUBLIC-SECTOR ORGANIZATIONAL NETWORKS: A CASE STUDY OF VOLUNTARY COURT NETWORKS
PublicationPurpose: The purpose of this study is to identify the problem of sustainability of public-sector 12 organizational networks on the example of common courts and what it implies for further 13 research. Methodology: The study used qualitative research tools in the form of structured 14 interviews. Interviews were conducted with 36 presidents and directors of common courts. 15 After conducting and transcribing each interview, their...
-
Impact of Boundary Conditions on Acoustic Excitation of EntropyPerturbations in a Bounded Volume of Newtonian Gas
PublicationExcitation of the entropy mode in the field of intense sound, that is, acoustic heating, is theoreticallyconsidered in this work. The dynamic equation for an excess density which specifies the entropy mode,has been obtained by means of the method of projections. It takes the form of the diffusion equation withan acoustic driving force which is quadratically nonlinear in the leading order. The diffusion coefficient isproportional...
-
Mathematical model of the energy consumption calculation during the pine sawn wood (Pinus sylvestris L.) drying process
PublicationThe article presents the modification of the existing mathematical model to calculate energy consumption during conventional drying process. Apart from energy consumption the model permits to estimate the time of high-temperature drying process. The drying medium is air and superheated steam mixture. The obtained calculation results were compared with conducted experimental tests of drying square-edged sawn sapwood timber (Pinus...
-
A concept of software extension of 3D low-PRF radar systems to 4D semi-medium-PRF radar systems
PublicationWe present a concept of software modification of three-dimensional (3D) radar systems, designed to work in the low pulse repetition frequency mode, that equips them with the ability to estimate the radial velocity and to properly measure the range of targets that are detected outside the radar’s instrumented range. Despite the fact that the proposed modifications are designed so as to require only minor changes in software, they...
-
MRAS-Based Switching Linear Feedback Strategy for Sensorless Speed Control of Induction Motor Drives
PublicationThis paper presents a newly designed switching linear feedback structure of sliding mode control (SLF-SMC) plugged with an model reference adaptive system (MRAS) based sensorless fieldoriented control (SFOC) for induction motor (IM). Indeed, the performance of the MRAS depends mainly on the operating point and the parametric variation of the IM. Hence, the sliding mode control (SMC) could be considered a good control alternative...
-
Analytical Modelling of the Multicell Piezoelectric Motor Based on Three Resonance Actuators
PublicationThis paper presents analytical model of the multicell piezoelectric motor. The results, obtained in the field of piezoelectric motors, have pointed out that these motors have potentially high possibilities in the future of special applications. The studied multicell piezoelectric motor have a stator using three rotating mode actuators. A theoretical analysis of operating principle of the rotating mode motor has been described....
-
Unusual streaming in chemically reacting gases
PublicationNonlinear stimulation of the vorticity mode caused by losses in the momentum of sound in the chemically reacting gas, is considered. The instantaneous dynamic equation which describes the nonlinear generation of the vorticity mode, is derived. It includes a quadratic nonlinear acoustic source. Both periodic and aperiodic sound may be considered as the origin of the vorticity flow. In the non-equilibrium regime of the chemical reaction,...
-
Standing Waves in One-Dimensional Resonator Contaning an Ideal Isothermal Gas Affected by the Constant Mass Force
PublicationThe study is devoted to standing acoustic waves in one-dimensional planar resonator which containing an ideal gas. A gas is affected by the constant mass force. Two types of physically justified boundary conditions are considered: zero velocity or zero excess pressure at both boundaries. The variety of nodal and antinodal points is determined. The conclusion is that the nodes of pressure and antinodes of velocity do not longer...
-
Application of Analytic Signal and Smooth Interpolation in Pulse Width Modulation for Conventional Matrix Converters
PublicationThe paper proposes an alternative and novel approach to the PWM duty cycles computation for Conventional Matrix Converters (CMC) fed by balanced, unbalanced or non–sinusoidal AC voltage sources. The presented solution simplifies the prototyping of direct modulation algorithms. PWM duty cycles are calculated faster by the smooth interpolation technique, using only vector coordinates, without trigonometric functions and angles. Both...
-
Low cost set-up for supercapacitors parameters evaluation
PublicationSupercapacitors are capable to store relatively high amount of energy comparing to its mass. Growing number of these devices applications requires development of new testing methods. Standard methods of evaluation of supercapacitor parameters, as cycling voltammetry, CV, galvanostatic cycling with potential limitation, GCPL, impedance measurements, require equipment of high cost...
-
Impact of configuration of earth continuity conductor on induced sheath voltages in power cables
PublicationIn high voltage power cable systems a problem of induced sheath voltages exist. Due to these voltages electric shock and damage of non-metallic outer sheath of the cables may occur. Exposure to voltage of the outer sheath may be very high in case of earth fault with high value of earth current. In order to reduce induced sheath voltages an earth continuity conductor (conductors) along power cables is applied. Configuration of this...
-
Tensile strength of a weave tendon suture using tendons of different sizes
PublicationThis study compared the maximum load, stress, elongation at failure and the mode of failure of three kinds of tendons most frequently used for tendon grafting and tendon transfers, using the Pulvertaftweave suture.
-
Regulacja napięcia w sieci nN z rozproszonymi źródłami energii
PublicationPodłączanie rozproszonych źródeł energii do sieci energetycznych niskiego napięcia powoduje powstawanie problemów zmienności i niesymetrii napięcia, zwłaszcza w przypadku dużych odległości od transformatora zasilającego. W skrajnych przypadkach zachodzi konieczność redukcji mocy generowanej przez źródło podczas oddawaniu energii do sieci. Rozwiązaniem tego problemu jest zastosowanie energoelektronicznego regulatora napięcia składającego...
-
Process zone in the Single Cantilever Beam under transverse loading. - Part I: Theoretical analysis
PublicationSingle Cantilever Beam (SCB) specimen loaded with a transverse force parallel to the crack front is proposed for the analysis of crack propagation phenomena under mixed mode conditions. The stress redistribution in the adhesive layer in the vicinity of the crack front so as the beam deformation are estimated using a Timoshenko beam on elastic foundation model. This model emphasizes the Mode II contribution due to flexural beam...
-
Quality assessment of ZnO-based varistors by 1/f noise
PublicationNoise has been used as a diagnostic tool of surge arrester varistor structures comprising of ZnO grains of various type and size. The physical and electrical properties of the measured samples have been described. In the experimental study, the applied measurement system and the results of noise measurements for the selected structures of varistors designed for the continuous working voltage 280 V, 440 V and 660 V have been presented....
-
Sinusoidal Alternating-Current Voltammetry and Metrological Properties of a Flat Voltammetric Electrode in the Time Domain
PublicationIn this paper there were analyzed metrological properties of a flat electrode used to mark ions with the method of sinusoidal alternating-current voltammetry in the situation where on its surface an electrochemical reversible reaction of oxidizing / reduction takes place. The result of the analysis conducted is that such a voltammetric electrode functions like a converter type I. Metrological properties of such an electrode in...
-
Analysis of dynamics of a map-based neuron model via Lorenz maps
PublicationModeling nerve cells can facilitate formulating hypotheses about their real behavior and improve understanding of their functioning. In this paper, we study a discrete neuron model introduced by Courbage et al. [Chaos 17, 043109 (2007)], where the originally piecewise linear function defining voltage dynamics is replaced by a cubic polynomial, with an additional parameter responsible for varying the slope. Showing that on a large...
-
Assessment of Fuel Cells’ State of Health by Low-Frequency Noise Measurements
PublicationWe proposed applying low-frequency (flicker) noise in proton-exchange membrane fuel cells under selected loads to assess their state of health. The measurement set-up comprised a precise data acquisition board and was able to record the DC voltage and its random component at the output. The set-up estimated the voltage noise power spectral density at frequencies up to a few hundred mHz. We observed the evolution of the electrical...
-
The equations for interactions of polarization modes in optical fibres including the kerr effect
PublicationWe have derived coupled nonlinear Schro¨ dinger equations (CNLSE) for arbitrary polarized light propagation in a single-mode fibre employing electromagnetic field complete description. We used a basis of transverse eigenmodes with appropriate projecting; hence, the nonlinear constants depend on the waveguide geometry. Accounting for a weak nonlinearity, which is connected to the Kerr effect, we have given explicit expressions for...
-
Interaction of Acoustic and Thermal Modes in the Vibrationally Relaxing Gases. Acoustic Cooling
PublicationThe dynamic equation which governs an excess temperature associated with the thermal mode in vibrationally relaxing gas is derived. The nonlinear transfer of acoustic energy to the energy of the thermal mode in a relaxing gas causes slow variation of temperature with time. The nal dynamic equation is instantaneous. All types of sound, including aperiodic, may be considered as an acoustic source of corresponding heating or cooling....
-
Comment on "On accurate capacitance characterization of organic photovoltaic cells"
PublicationIn the 100th volume of Applied Physics Letters Carr and Chaudhary have presented a work on capacitance characterization of organic photovoltaic cells. The work concerns small signal measurements of various organic photovoltaic structures. The authors however limit their considerations to one part of small signal response, namely to capacitance measured either in parallel mode or in series mode. This attitude generally does not...
-
How to adapt Lean Six Sigma to improve performance of SMEs of manufacturing sector
PublicationThe main objective of the paper is to present the utilitarian effect of the adaptation of the Lean Six Sigma concept and its implementation in the small and medium-sized enterprises of the manufacturing sector. The original methodology was developed on the basis of research carried out in the Polish and French enterprises from 2009 to 2011. In the case of SMEs, the use of the concept of Lean Six Sigma is much less common, as...
-
A study on diagnosing both isotropic and orthotropic, intentionally damaged laminates
PublicationBeing the most detrimental mode in laminated structures, delamination initially degrades local structural strength, and lastly causes global structural failure, thus necessitating delamination identification at its incipient stages. For identification purposes, a comprehensive numerical and experimental study on delamination within both the laminated isotropic acrylic-glass and orthotropic epoxyglass plates is presented. As the...
-
Instrumented end notched flexure - Crack propagation and process zonemonitoring Part II: Data reduction and experimental
PublicationA mode II instrumented end notched flexure three point bending (ENF) adhesion test is described. The adhesive joint consists of two aluminium alloy (AW7075-T6) plates bonded with a structural epoxy adhesive (Hysol EA 9395™). Strain gauges are attached to the outer surface (backface) of the substrates in the lengthwise direction to measure local surface strain during crack propagation. Simultaneously, load/displacement measurements...
-
Prediction of fracture toughness in fibre-reinforced concrete, mortar, and rocks using various Machine learning techniques
PublicationMachine Learning (ML) method is widely used in engineering applications such as fracture mechanics. In this study, twenty different ML algorithms were employed and compared for the prediction of the fracture toughness and fracture load in modes I, II, and mixed-mode (I-II) of various materials, including fibre-reinforced concrete, cement mortar, sandstone, white travertine, marble, and granite. A set of 401 specimens of “Brazilian...
-
A current-controlled FET
PublicationA novel semiconductor device, viz., Horizontally-Split-Drain Current-Controlled Field-Effect Transistor (HSDCCFET) with two control electrodes is proposed in this works. For the sake of brevity, the device can be called a CCFET. Operating principle of the proposed transistor is based on one of the galvanomagnetic phenomena, the Biot-Savart-Laplace law and a Gradual Channel Detachment Effect (GCDE). The transistor is dedicated...
-
Three electrode configuration measurements of electrolyte-diffusion barrier-cathode interface
PublicationMeasurements of a system consisting of cathode/doped ceria diffusion barrier/doped zirconia electrolyte were made using two- and three-electrode configuration. Results obtained on a three-electrode measurement configuration were compared with and reflect the results obtained in two-electrode configuration. Three-electrode measurements allowed separating the impact of the symmetrical interface in the investigated system. They also...
-
Bulk linearized CMOS differential pair transconductor for continuous-time OTA-C filter design
PublicationIn this paper, the MOS differential pair driven simultaneously from gates and bulk terminals is described. An approximated analytical solution of the voltage to current transfer function has been found for the proposed circuit. Four possible combinations of gate and bulk connections of the input signal are presented. Basing on the configuration giving the best linearity, the operational transconductance amplifier (OTA) has been designed...
-
Activity coordination of capacitor banks and power transformer controllers in order to reduce power losses in the MV grid
PublicationOne of the main issues related to the optimization of the MV (middle voltage) network is to reduce losses of active and reactive power. Lower losses of active and reactive power give not only economic advantage, but also improvement of energy quality. The object of regulation that can be used for these purposes are transformer with On-Load Tap Changer and capacitor's banks. This paper presents results of analysis of the possibility...
-
On analog comparators for CMOS digital pixel applications. A comparative study
PublicationVoltage comparator is the only – apart from the light-to-voltage converter – analog component in the digital CMOS pixel. In this work, the influence of the analog comparator nonidealities on the performance of the digital pixel has been investigated. In particular, two versions of the digital pixel have been designed in 0.35 μm CMOS technology, each using a different type of analog comparator. The properties of both versions have...
-
Unity-Gain Zero-Offset CMOS Buffer with Improved Feedforward Path
PublicationA voltage unity-gain zero-offset CMOS amplifier with reduced gain error and increased PSRR (power supply rejection ratio) is proposed. The amplifier uses two feed mechanisms, negative feedback and supporting positive feedforward, to achieve low deviation from unit gain over the entire input range. The circuit, designed in a standard 180-nanometer 1.8-voltage CMOS process, is compared with two known buffers of similar topology,...
-
Chitosan/poly(4-vinylpyridine) coatings formed on AgNPs-decorated titanium
PublicationElectrophoretic deposition (EPD) of chitosan/poly(4-vinylpyridine) (chit/P4VP) coatings on titanium substrates previously decorated with silver nanoparticles (AgNPs) was performed at different content of P4VP in the suspension and different voltage values. The results revealed that the composite coatings were formed, well-adjacent to the titanium substrate, of suitable roughness, hydrophilicity, and corrosion resistance. The voltage...
-
The adaptive backstepping control of PMSM supplied by current source inverter for the field weakening region
PublicationThe sensorless control system of permanent magnet synchronous motor PMSM supplied by current source inverter for field weakening operation is presented in this paper. The adaptive backstepping control system and the backstepping speed observer are presented. The control system is based on multi-scalar variables. The control variables are: dc-link voltage and the output current vector pulsation. The control system was named voltage...
-
Motor Cable Influence on the Conducted EMI Emission of the Converter Fed AC Motor Drive. - Vol. 1
PublicationInvestigation of conducted electromagnetic interference in AC motor drives fed by pulse width modulated voltage converters requires considering parasitic capacitances in converters, motor windings and feeding cables to be taken into account. Motor voltage transients and related conducted electromagnetic emission are significantly correlated with resonance effects occurring in load circuits. The levels of intensity of these phenomena...
-
Installation of Compensators in the Power System Transmission Grid
PublicationThe article discusses issues of reactive power compensation in transmission grids, with particular focus on the selection of compensator locations and basic parameters. Attention was focused on modern power electronics systems that ensure full automatic compensator adjustment to voltage or power criteria.