Search
Filters
total: 1180
filtered: 952
Search results for: STATIONARY FLOATING OBJECT
-
Numerical Simulations of Hydrodynamic Open-Water Characteristics of a Ship Propeller
PublicationThe paper presents the results of numerical simulations of ship propeller operation bearing the name of Propeller Open Water (POW) Tests. The object of tests was a sample ship propeller (PPTC1), the geometrical and kinematic data of which are available, along with the results of model tests, on the official page of the research centre involved in the measurements. The research aimed at verifying the correctness of results of numerical...
-
Erroneous GNSS Strain Rate Patterns and their Application to Investigate the Tectonic Credibility of GNSS Velocities
PublicationThe paper concerns investigation of the credibility of tectonic interpretation of GNSS strain rates. The analysis was focused on stable regions, where the crustal deformations are small and the reliability of GNSS velocities is questionable. We are showing how the unreliable motion of stations affects calculated strains around them. We expressed distribution of local principal strains by a sinusoidal function and used them to investigate...
-
Hydraulic resistance analyses of selected elements of the prototype Stirling engine
PublicationThe paper presents the results of simulation tests of hydraulic resistance and temperature distribution of the prototype Stirling alpha engine supplied with waste heat. The following elements were analyzed: heater, regenerator and cooler. The engine uses compressed air as a working gas. Analyses were carried out for three working pressure values and different engine speeds. The work was carried out in order to optimize the configuration...
-
FEM and experimental investigations of concrete temperature field in the massive stemwall of the bridge abutment
PublicationThe paper deals with the prediction of early-age concrete temperature of cast-in-place stemwall of the bridge abutment. The considered object is an arch bridge located in Gda´nsk. In the case of massive structures, it is particularly important to not exceed the temperature difference between the core and the concrete surface. Too high temperature gradient generates an increase in thermal stresses, what could be the reason of exceeding...
-
Determination of vertical displacements by using the hydrostatic levelling systems with the variable location of the reference sensor,
PublicationAbstract: In this paper, the author proposed a new method for determination of vertical displacements with the use of hydrostatic levelling systems. The traditional method of hydrostatic levelling uses a rule in which a position of reference sensor is stable. This assumption was not adapted in the proposed method. Regarding the issue mentioned above, the reference sensor is treated in the same way as the others sensors that measure...
-
MULTI-CRITERIA MODEL IN MULTIFUNCTIONAL BUILDING SYSTEM DESIGN PROCESS
PublicationThe paper presents a multi-criteria approach in multifunctional building system design process. The aim is to develop a theory relative to the engineering system of multifunctional with a mathematical representation defined by a holistic network for the lifecycle of the designed object. The idea of work was to define the structure of a complex system. Background for the presented field is to develop a design strategy for multifunctional...
-
Evidence of mutations conferring resistance to clarithromycin in wastewater and activated sludge
PublicationThe occurrence of clarithromycin in wastewater samples and of the activated sludge bacteria possibly resistant to this pharmaceutical was the object of the study. Samples of wastewater or activated sludge were taken from a municipal wastewater treatment plant in summer and winter and characterised regarding their clarithromycin concentrations and the presence of nucleic acid fragments (Cla-sequences) known to be responsible for...
-
Recovering Evaluation of Narrow-Kerf Teeth of Mini Sash Gang Saws
PublicationSash gang saws with narrow-kerf saw blades are used in the production of glued laminate flooring elements in plants where dry technology is applied. This means that boards or friezes are sawn into top layer lamellae in dry conditions (moisture content of about 10–12%) from expensive wood species, often exotic. The object of this research was stellite-tipped teeth of narrow kerf saw blades sharpened under industrial conditions....
-
Determination of magnetisation conditions in a Double-Core Barkhausen Noise measurement set-up
PublicationThe magnetic Barkhausen effect is useful forassessing 1D and 2D stress states of ferromagnetic steelobjects. However, its extension to technically importantmaterials, such as duplex anisotropic steels, remains challenging. The determination of magnetisation inside the studied object and the electromagnet for various geometries, materials and magnetisation angles is a key issue.Three-dimensional, dynamic finite element analysis...
-
Methods for quality improvement of multibeam and LiDAR point cloud data in the context of 3D surface reconstruction
PublicationPoint cloud dataset is the transitional data model used in several marine and land remote-sensing applications. During further steps of processing, the transformation of point cloud spatial data to more complex models containing higher order geometric structures like edges and facets may be possible, if an appropriate quality level of input data is provided. Point cloud datasets usually contain a considerable amount of undesirable...
-
Multiclass AdaBoost Classifier Parameter Adaptation for Pattern Recognition
PublicationThe article presents the problem of parameter value selection of the multiclass ``one against all'' approach of an AdaBoost algorithm in tasks of object recognition based on two-dimensional graphical images. AdaBoost classifier with Haar features is still used in mobile devices due to the processing speed in contrast to other methods like deep learning or SVM but its main drawback is the need to assembly the results of binary...
-
Properties of Thermally Dewetted Thin Au Films on ITO-Coated Glass for Biosensing Applications
PublicationNoble metal nanostructures are object of great interest due to their unique optical and electronic properties exploited in nanotechnology, medicine, biochemistry, and surface-enhanced spectroscopies. In this work, the Au nanoparticle (NP) structures for application in biosensing obtained by dewetting are investigated in dependence on their preparation conditions. Structures are produced from thin Au films (5–30 nm) sputtered onto...
-
Point cloud based surface analysis of prestressed concrete element in exceeded state of serviceability
PublicationBy definition, serviceability state is characterized by the fact that despite meeting the requirements associated with carrying capacity, the object is not suitable for use. Serviceability limit state refers to factors, such as durability, overall stability, fire resistance, cracking, excessive vibration. Perfect examples of exceeded serviceability state are the improper vibration of a skyscraper, which inhabitants may suffer from...
-
Suppression of distortions in signals received from Doppler sensor for vehicle speed measurement
PublicationDoppler sensors are commonly used for movement detection and speed measurement. However, electromagnetic interference and imperfections in sensor construction result in degradation of the signal to noise ratio. As a result, detection of signals reflected from moving objects becomes problematic. The paper proposes an algorithm for reduction of distortions and noise in the signal received from a simple, dual-channel type of a Doppler...
-
Application of Rapid Prototyping technology in the manufacturing of turbine blade with small diameter holes
PublicationThe article presents the possibilities of using Rapid Prototyping (RP) technology in the manufacturing of turbine blades with small diameter holes. The object under investigation was gas turbine blade with small diameter cooling holes and holes for generating longitudinal vortices. A turbine blade model was produced by means of Direct Metal Laser Sintering (DMLS) technology and subsequently validated in terms of detection and accuracy...
-
Woda jako element przyrodniczy w przestrzeni zamieszkiwania. Ideowe formy architektoniczne
PublicationMożna obecnie zaobserwować nasilające się zjawisko pozamiejskich migracji. Sprzyja im dogodność warunków zamieszkiwania poza miastem. Pojezierze Kaszubskie to obszar, gdzie powstaje wiele pozamiejskich, czasowo zamieszkiwanych domów. Często lokowane są one pobliżu jezior i rzek. Wydaje się, że woda stanowi szczególny walor tych miejsc. Nawiązywane poprzez nią relacje i poczucie współuczestnictwa skłoniły do poszukiwania szczególnych...
-
Recent developments and future trends in solid phase microextraction techniques towards green analytical chemistry
PublicationSolid phase microextraction find increasing applications in the sample preparation step before chromatographic determination of analytes in samples with a complex composition. These techniques allow for integrating several operations, such as sample collection, extraction, analyte enrichment above the detection limit of a given measuring instrument and the isolation of analytes from sample matrix. In this work the information about...
-
Three modes of electrochemical impedance spectroscopy measurements performed on vanadium redox flow battery
PublicationThis article presents an innovative approach to monitor working redox flow batteries using dynamic electrochemical impedance spectroscopy, diverging from the commonly sequential impedance methods carried out under potentiostatic or galvanostatic conditions close to the open circle voltage. The authors introduce a fresh variation of dynamic impedance measurement that leverages an amplitude-modulated multi-frequency alternating current...
-
Evaluation of the yield, chemical composition and biological properties of essential oil from bioreactor-grown cultures of Salvia apiana microshoots
PublicationMicroshoot cultures of the North American endemic Salvia apiana were established for the first time and evaluated for essential oil production. Stationary cultures, grown on Schenk-Hildebrandt (SH) medium, supplemented with 0.22 mg/L thidiazuron (TDZ), 2.0 mg/L 6-benzylaminopurine and 3.0% (w/v) sucrose, accumulated 1.27% (v/m dry weight) essential oil, consisting mostly of 1,8-cineole, β-pinene, α-pinene, β-myrcene and camphor....
-
Detection and time/frequency analysis of electric fields in the ground
PublicationThis paper sets out to detect and characterize electric fields in the ground (such as stray current fields) using a tandem time/frequency method of signal analysis. Results were obtained from investigations performed in the presence of a generated electric field with controlled variable characteristics, and in the presence of an electric field generated by a tramline. The analysis of measurement registers was performed using Short‐Time...
-
Controlling the size and morphology of precipitated calcite particles by the selection of solvent composition
PublicationCalcium carbonate particles were obtained in the reaction of calcium hydroxide with carbon dioxide at 65°C. Initial Ca(OH)2 suspensions were prepared in pure water and aqueous solutions of ethylene glycol or glycerol of the concentration range up to 20% (vol.). The course of reaction was monitored by conductivity measurements. Precipitated solids were analyzed by FTIR, XRD, SEM and the particles size distribution was determined...
-
Biocomposites from recycled resources as candidates for laboratory reference material to validate analytical tools used in organic compounds emissions investigation
PublicationA suitably chosen reference material should meet specific criteria like representing one of the compound classes most commonly occurring in indoor materials as well as having optimal long-term stability during storage and transport to its destination point and having a compact size. The described interdisciplinary pilot research was aimed to develop and characterize a polymer-based candidate for the laboratory reference material...
-
Adaptive Positioning Systems Based on Multiple Wireless Interfaces for Industrial IoT in Harsh Manufacturing Environments
PublicationAs the industrial sector is becoming ever more flexible in order to improve productivity, legacy interfaces for industrial applications must evolve to enhance efficiency and must adapt to achieve higher elasticity and reliability in harsh manufacturing environments. The localization of machines, sensors and workers inside the industrial premises is one of such interfaces used by many applications. Current localization-based systems...
-
Capillary gas chromatography using a -cyclodextrin forenantiomeric separation of methylamphetamine, its precursors andchloro intermediates after optimization of the derivatization reaction
PublicationtThe enantiomeric ratio of methylamphetamine (MAMP) is closely related to the optical activity of precur-sors and reagents used for the synthesis and this knowledge can provide useful information concerningthe origins and synthetic methods used for illicit manufacture. The information can be utilized for reg-ulation of the precursors and investigation of the manufacturing sources but this requires analyticalprocedures to determine...
-
INFLUENCE OF MEASURING CONDITIONS ON TYRE/ROAD NOISE
PublicationA decisive factor for the development of tyres and road surfaces is the ability to conduct representative and reproducible measurements of selected characteristics related to the interaction of tyres and road surfaces. In terms of tyre/road noise measurements in Europe two methods described in ISO/FDIS 11819-2 and ECE Regulation No.117 are used. The latter is compulsory for assigning the tyre noise labels. The methodologies differ...
-
Development Of Dynamic Method For Evaluation Of Corrosion Rate On The Example Of Organic Corrosion İnhibitor
PublicationMeasurements of the corrosion rate belong to the most important aspects of materials science. In order to reduce material loss corrosion inhibitors are used. However selection of proper inhibitor should be based on evaluation of its mechanism and effective concentrations. Mechanism of inhibition usually has dynamic character so physicochemical parameters are changing in time. Most of actually used methods...
-
Solventless and solvent-minimized sample preparation techniques for determining currently used pesticides in water samples: A review
PublicationThe intensification of agriculture means that increasing amounts of toxic organic and inorganic compounds are entering the environment. The pesticides generally applied nowadays are regarded as some of the most dangerous contaminants of the environment. Their presence in the environment, especially in water, is hazardous because they cause human beings to become more susceptible to disease. For these reasons, it is essential to...
-
Shore Construction Detection by Automotive Radar for the Needs of Autonomous Surface Vehicle Navigation
PublicationAutonomous surface vehicles (ASVs) are becoming more and more popular for performing hydrographic and navigational tasks. One of the key aspects of autonomous navigation is the need to avoid collisions with other objects, including shore structures. During a mission, an ASV should be able to automatically detect obstacles and perform suitable maneuvers. This situation also arises in near-coastal areas, where shore structures like...
-
Ocena warunków nasłonecznienia i projektowanie elektrowni słonecznych z wykorzystaniem dedykowanego oprogramowania oraz baz danych
PublicationPrzytoczono typowe dla obszaru Polski wartości nasłonecznienia. Zaprezentowano sposoby dokładniejszego określenia wartości nasłonecznienia w oparciu o bazy danych o nasłonecznieniu i aplikacje komputerowe. Narzędzia te pozwalają w pełniejszy sposób uwzględnić kąt nachylenia i azymut modułów fotowoltaicznych, linię horyzontu i zacienienie oraz zmienność nasłonecznienia w ciągu roku na podstawie statystycznych wartości nasłonecznia...
-
METODOLOGICZNE PROBLEMY REALIZACJI BADAŃ EMPIRYCZNYCH URZĄDZEŃ ENERGETYCZNYCH OKRĘTOWYCH SIŁOWNI SPALINOWYCH
PublicationW referacie scharakteryzowano w ujęciu ogólnym wymagania obowiązujące a badaniach naukowych, zwłaszcza empirycznych, w zakresie metodologicznym i na przykładzie badań urządzeń energetycznych siłowni okrętowych, ze szczególnym uwzględnieniem okrętowych silników spalinowych o zapłonie samoczynnym. Scharakteryzowano problemy pojawiające się przy formułowaniu i weryfikacji hipotez naukowych oraz przedstawianiu tez i ich udowadnianiu....
-
Prowadzenie ruchu małego źródła kogeneracji gazowej według kryterium efektu ekonomicznego
PublicationCechą charakterystyczną źródeł gazowych jest ich duża elastyczność ruchowa, w porównaniu do większości źródeł konwencjonalnych i odnawialnych. Cecha ta może i powinna być wykorzystywana do poprawy wskaźników ekonomicznych obiektu. W tym celu należy przeanalizować możliwości jakie daje prowadzenie ruchu źródeł nie w standardzie pracy z wymuszeniem zapotrzebowania na ciepło, ale właśnie maksymalnie wykorzystując elastyczność ruchową...
-
Prowadzenie ruchu małej elektrociepłowni gazowej według kryterium efektu ekonomicznego
PublicationCechą charakterystyczną źródeł gazowych jest ich duża elastyczność ruchowa, w porównaniu do większości źródeł konwencjonalnych i odnawialnych. Cecha ta może i powinna być wykorzystywana do poprawy wskaźników ekonomicznych obiektu. W tym celu należy przeanalizować możliwości jakie daje prowadzenie ruchu źródeł nie w standardzie pracy z wymuszeniem zapotrzebowania na ciepło, ale właśnie maksymalnie wykorzystując elastyczność ruchową...
-
A la recherche d’une coherence perdue – Possible Arguments for the Non-application of EU Law in Member States
PublicationThe European Union (EU) is an international organization which has a broad scope of competences that have been transferred to it by its Member States in the founding Treaties. The object of the article is to identify arguments raised, or that potentially might be raised, by national Constitutional Courts (and in the future possibly by other actors as well) to exclude in certain instances the application of EU law or EU jurisprudence...
-
An Efficient Framework For Fast Computer Aided Design of Microwave Circuits Based on the Higher-Order 3D Finite-Element Method
PublicationIn this paper, an efficient computational framework for the full-wave design by optimization of complex microwave passive devices, such as antennas, filters, and multiplexers, is described. The framework consists of a computational engine, a 3D object modeler, and a graphical user interface. The computational engine, which is based on a finite element method with curvilinear higher-order tetrahedral elements, is coupled with built-in...
-
Influence of Bingham fluid viscosity on energy performances of a vortex chamber pump
PublicationOne of the problems in the development of coal-water technologies is the use of reliable and long-lasting pumps. To date, classic pumps, due to the use of mechanical moving parts and seals, are subject to rapid abrasive wear. The solution to this problem can lie in the creation of new vortex chamber pumps developed by the authors. They are highly reliable, simple in design and have no moving parts. The object of this paper consists...
-
Comparison of 3D Point Cloud Completion Networks for High Altitude Lidar Scans of Buildings
PublicationHigh altitude lidar scans allow for rapid acquisition of big spatial data representing entire city blocks. Unfortunately, the raw point clouds acquired by this method are largely incomplete due to object occlusions and restrictions in scanning angles and sensor resolution, which can negatively affect the obtained results. In recent years, many new solutions for 3D point cloud completion have been created and tested on various objects;...
-
Incomplete Cross-Bonding in the MV Line. Experience from the Operation of MV Single Cable Lines
PublicationCable lines are one of the basic components of power systems. Medium and high voltage cables mainly comprise a metallic sheath, which is concentric to the main core conductor. There are several operating schemes of such cable lines, which differ in the place of earthing of sheaths and the possible use of the sheaths and/or conductors crossing. The sheaths cross-bonding is typically done in two places of one cable line section,...
-
Material Identification of the Human Abdominal Wall Based On the Isogeometric Shell Model
PublicationThe human abdominal wall is an object of interest to the research community in the context of ventral hernia repair. Computer models require a priori knowledge of constitutive parameters in order to establish its mechanical response. In this work, the Finite Element Model Updating (FEMU) method is used to identify an heterogeneous shear modulus distribution for a human abdominal wall model, which is based on nonlinear isogeometric...
-
Gold nanoparticles evaluation using functional optical coherence tomography
PublicationThe main object of this research was to assess the ability to characterize the gold nanoparticles using optical modalities like optical coherence tomography. Since the nanoparticles, especially gold one, have been very attractive for medical diagnosis and treatment the amount of research activities have been growing rapidly. The nanoparticles designed for different applications like contrast agents or drugs delivery change the...
-
Knowledge-Based Virtual Modeling and Simulation of Manufacturing Processes for Industry 4.0
PublicationABSTRACT Industry 4.0 aims at providing a digital representation of a production landscape, but the challenges in building, maintaining, optimizing, and evolving digital models in inter-organizational production chains have not been identified yet in a systematic manner. In this paper, various Industry 4.0 research and technical challenges are addressed, and their present scenario is discussed. Moreover, in this article, the novel...
-
Toward Robust Pedestrian Detection With Data Augmentation
PublicationIn this article, the problem of creating a safe pedestrian detection model that can operate in the real world is tackled. While recent advances have led to significantly improved detection accuracy on various benchmarks, existing deep learning models are vulnerable to invisible to the human eye changes in the input image which raises concerns about its safety. A popular and simple technique for improving robustness is using data...
-
Combined analysis of whole human blood parameters by Raman spectroscopy and spectral-domain low-coherence interferometry
PublicationIn this article the simultaneous investigation of blood parameters by complementary optical methods, Raman spectroscopy and spectral-domain low-coherence interferometry, is presented. Thus, the mutual relationship between chemical and physical properties may be investigated, because low-coherence interferometry measures optical properties of the investigated object, while Raman spectroscopy gives information about its molecular...
-
Highly porous nanoberyllium for X-ray beam speckle suppression
PublicationThe speckle suppressor device containing highly porous nanoberyllium is proposed for manipulating with the spatial coherence length and removing undesirable speckle structure during the imaging experiments. We report a special device called the speckle suppressor, which contains the highly porous nanoberyllium plate, compacted from both sides by two beryllium windows. By insertion the speckle suppressor in the X-ray beam it allows...
-
THE APPLICATION OF KALMAN FILTERING TO PREDICT VERTICAL RAIL AXIS DISPLACEMENTS OF THE OVERHEAD CRANE BEING A COMPONENT OF SEAPORT TRANSPORT STRUCTURE
PublicationAs the devices designed to transport materials, the overhead cranes should meet certain geometric requirements for their operation to be safe. The presently available geodetic equipment, in particular total stations, provides opportunities for precise 3D measurements of coordinates of the controlled points. These coordinates make a basis for correcting the height of crane runway axes. The paper presents a method to calculate position...
-
Standard deviation as the optimization criterion in the OptD method and its influence on the generated DTM
PublicationReduction of the measurement dataset is one of the current issues related to constantly developing technologies that provide large datasets, eg. laser scanning. It could seems that presence and evolution of processors computer, increase of hard drive capacity etc. is the solution for development of such large datasets. And in fact it is, however, the “lighter” datasets are easier to work with. Additionally, reduced datasets can...
-
A HISTORICAL BUILDING'S RESTORATION IN THE CONSTRUCTIONAL ASPECT ON THE EXAMPLE OF A BUILDING LOCATED IN POLAND
PublicationObjects of cultural heritage are an extremely important element in the proper functioning of the social life. They provide information on our ancestors' actions, as well as shape our culture and social awareness. It is important for the historical objects to provide those information accurately, that is without any unnecessary human intervention over the years of the monument's existence. However, it is not always possible due...
-
Experimental tests of lintel hybrid beams
PublicationThe results of experimental tests of lintel hybrid beams made of air concrete and prestressed concrete were presented in paper. Blocks of air concrete was a protective element for the construction one. The length of hybrid beams was 3.0 m, while total height 27 cm. It was assumed that hybrid beams will work in the simply-supported scheme (with a 10 cm support) loaded uniformly over the entire length. The object of the tests were...
-
Experience-Based Decisional DNA (DDNA) to Support Product Development
PublicationKnowledge and experience are important requirements for product development. The aim of this paper is to propose a systematic approach for industrial product development. This approach uses smart knowledge management system comprising of Set of Experience Knowledge Structure and Decisional DNA (DDNA) along with Virtual Engineering Tools (Virtual engineering object, Virtual engineering process, and Virtual engineering factory)....
-
Programmatic Simulation of Laser Scanning Products
PublicationThe technology of laser scanning is widely used for producing three-dimensional digital representations of geographic features. The measurement results are usually available in the form of 3D point clouds, which are often used as a transitional data model in various remote sensing applications. Unfortunately, while the costs of Light Detection And Ranging scanners have dropped significantly in recent years, they are still considered...
-
The Eastern Battery in Świnoujście, Poland - history and architecture of a Prussian coastal fort from the 19th century
PublicationThe article describes the history, architecture and development of the Eastern Battery (also known as the Gerhard Fort) – one of three remaining coastal forts in Świnoujście (former Swinemünde) located in northern Poland, by the Baltic Sea. The research is mostly based on historical cartographic material and architectural plans verified during field studies. This data served to create a digital model – one of the results of the...