Search
Search results for: hydrodynamic bearing, static characteristics, reynolds equation, calculation procedures
-
Influence of bush wear in water lubricated marine stern tube bearings with shaft misalignment
PublicationWater lubricated propeller shaft bearings are frequently employed on modern ships due to their advantages such as durability, simplicity and low price. Specific working conditions on ships cause shaft misalignment which often results in rapid wearing of bush and shaft. Shaft misalignment could be an effect of manufacturing or assembly faults but sometimes it appears due to hull or shaft deformation. The wearing process has influence...
-
Simulation of large thrust-bearing performance at transient states, warm and cold start-up
PublicationThe start-up of a large hydrodynamic thrust bearing of a vertical hydrogenerator is one of the most critical situations during the lifetime of a bearing. Hydrodynamic load capacity is low due to low speed and higher thermal deformations of the pad. A new approach to the simulation of a hydrodynamic bearing is shown in this article. A combination of finite elements method and computational fluid dynamics is used to perform the transient...
-
Study of the Influence of Heat Convection Coefficient on Predicted Performance of a Large Tilting-Pad Thrust Bearing
PublicationPart of the heat generated by the shearing of the lubricating film during operation of a hydrodynamic bearing is transferred to the bearing components. In the case of the pad, which is usually fully submerged in the lubricating oil, heat is further transferred at the pad free walls to the oil by convection. This mechanism causes a thermal gradient in a pad and, consequently, its thermal deflection. In large hydrodynamic thrust...
-
RESEARCH ON HYDRODYNAMIC PEEK JOURNAL BEARINGS LUBRICATED WITH WATER AND OIL
PublicationThe main purpose of the research was to determine the possibilities and experimentally test the benefits of replacing conventional oil lubrication with ecological water lubrication. Tests were carried out on a test rig for hydrodynamic radial bearings under conditions representative of the expected applications for the bearing in water turbines. Bearings made from the polymer material PEEK (polyether ether ketone) were tested under static...
-
Design of horizontal axis wind and water turbines
PublicationThe basic hydrodynamic principles of horizontal axis turbines are presented. Computational methods based on vortex theory for design of such turbines and for calculation of their hydro or aerodynamic characteristics are described in detail. These methods are applicable both to wind and water turbines. The influence of detailed turbine geometry on its characteristics is presented. Several practical computational examples of different...
-
The Experimental Determination of Bearings Dynamic Coefficients in a Wide Range of Rotational Speeds, Taking into Account the Resonance and Hydrodynamic Instability
PublicationMethods for the experimental determination of dynamic coefficients are commonly used for the analysis of various types of bearings, including hydrodynamic, aerodynamic and foil bearings. There are currently several algorithms that allow estimating bearing dynamic coefficients. Such algorithms usually use various excitation techniques applied to rotor–bearings systems. So far only a small number of scientific publications show how...
-
Application of the fluid–structure interaction technique for the analysis of hydrodynamic lubrication problems.
PublicationFluid–structure interaction technique seems to be one of the most promising possibilities for theoretical analysis of lubrication problems. It allows coupling of different physical fields in one computational task, taking into account the interaction between them. In this article, two sets of fluid–structure interaction analyses focusing on the bearing performance evaluation are presented. One analysis was applied to a water-lubricated...
-
Fluid Mechanics, L/L/E, DaPE, sem. 04, summer 21/22 (PG_00050282)
e-Learning CoursesLECTURES Introduction and basic definitions. Properties of fluids. Models of fluids. Fluids in equilibrium. Determination of hydrostatic forces. Archimedes" law. Methods of fluid flow description. General motion of fluid. Deformation of fluid element. Vortex motion of fluid. Principles of conservation of mass, momentum and energy. Balance of entropy. Navier-Stokes equation. Bernoulli equation. Similarity of flow phenomena. Potential...
-
Combined thrust radial bearing of a submarine main shaft – Design and analysis of failure
PublicationThis paper presents an analysis of the combined thrust radial bearing of a submarine propulsion shaft. The lubrication system of the bearing is based on a fixed ring. The efficiency of the lubrication system depends on the shaft speed and temperature, which affects oil viscosity. In turn, the thrust bearing load also depends on the rotational speed of the shaft, because as the speed increases, the drag of the ship increases simultaneously,...
-
The experimental identification of the dynamic coefficients of two hydrodynamic journal bearings operating at constant rotational speed and under nonlinear conditions.
PublicationHydrodynamic bearings are commonly used in ship propulsion systems. Typically, they are calculated using numerical or experimental methods. This paper presents an experimental study through which it has been possible to estimate 24 dynamic coefficients of two hydrodynamic slide bearings operating under nonlinear conditions. During the investigation, bearing mass coefficients are identified by means of a newly developed algorithm....
-
Selected problems of experimental investigation of dynamically loaded journal bearings
PublicationIn the paper some problems concerning relations between external bearing loadings and critical lining stresses are described for test stand with rotating load vector. According to the standard ISO 7905/1 this type of test stand, for dynamically loaded slide bearing, is recommended as a basic research unit for material testing in a complete bearing unit. The lining stress calculation results occurred being dependent on applied calculation...
-
HYDRODYNAMIC THRUST BEARINGS WITH POLYMER LINING
PublicationPolymeric linings of sliding surfaces of the hydrodynamic bearings have been used successfully for over 50 years. Despite of their long history of operation and research, they have not become wide spread in industrial applications. This fact may be surprising, considering th e conclusions that have been published concerning bearing operation and design. This paper summarizes the current...
-
Numerical analysis on axial capacity of steel built-up battened columns
PublicationThis paper deals with the numerical analysis aimed at study the bearing capacity of pinended steel built-up columns under axial compression. Finite element (FE) models were performed for the columns presented in the literature. The main problem discussed in the article is the shape and magnitude of geometric imperfections introduced into the numerical FE model, necessary to obtain the load capacity consistent with the experimental...
-
OPERATING CONDITIONS OF SLIDE BEARINGS OF MILLS USED IN KGHM POLSKA MIEDŹ S.A.
PublicationThe paper contains the results from a tec hnical analysis of the conditions of the operation of hydrodynamic bearings supporting the drums of ore processing mills at KGHM Polska Mied ź S.A. A theoretical analysis was performed on the grounds of onsite examination and measurem ents of principal dimensions of the bearings of interest. The computer simulation covered the characteristics of the oil film in the bearings...
-
Design of a test bench for determining the general characteristics of an internal combustion engine using a hydraulic power take-off system
PublicationThe paper presents a design of an engine test bench, which is used to determine the general characteristics of a truck engine using a power take-off (PTO). PTO drives a hydraulic system that generates a load on the engine at various points in its operation in the power range specified by the hydraulic system. The design allows for stationary and mobile tests with the test bench mounted on the truck, without any modification of...
-
Intelligent microbearing project with memory of stress-strain history
PublicationTaking into account the increasing need of intelligent micro-bearing with memory, this paper presents the optimization, simulation and practical application of operating parameters(load carrying capacity, friction forces, friction coefficient, wear), simulation for hydrodynamic HDD micro-bearing with curvilinear nano-grooved journal profile. One of the reason of such journal profile is that this journal profile contributes to the...
-
Database of the illustrative simulations of the nonstandard approximation of the generalized Burgers–Huxley equation
Open Research DataThe presented dataset is a result of numerical analysis of a generalized Burgers–Huxley partial differential equation. An analyzed diffusive partial differential equation consist with nonlinear advection and reaction. The reaction term is a generalized form of the reaction law of the Hodgkin–Huxley model, while the advection is a generalized form of...
-
Numerical Study of the Impinging Jets Formed by an Injector with Different Nozzle Diameters
Open Research DataThe data set contains the simulation files related to the research paper “Numerical Study of the Impinging Jets Formed by an Injector with Different Nozzle Diameters”, https://doi.org/10.4271/2022-01-1080.
-
Results of the “DPDT-Auger” Research Project on Screw Displacement Piles
PublicationThe main objective of the “DPDT-Auger” research project was to test the prototype DPDT auger for forming screw displacement piles in the ground (patented in Poland in 2020). An additional aim was to develop design methods and rules for the making of such piles. The augers and piles were first tested on a model scale, and then more extensively in the real scale on experimental field plots. The results found the overall functionality...
-
Modeling lubricant flow between thrust-bearing pads
PublicationInlet temperature is one of the main inputs in all models for the analysis of fluid film bearing performance. At the same time, inlettemperature distribution and also oil velocity distribution at the inlet are the result of flow phenomena in the gap between the bearingpads. These phenomena are complex and in many cases further affected by any special arrangements of forced oil supply to the gapbetween pads. The reason for such...
-
New concept of drilling auger for displacement pile installation
PublicationIn 2020, a new version of the screw displacement auger for pile installation in soil was developed and patented in Poland. It was named DPDT (Displacement Pile Drilling Tool). The general aim of its development was to reduce the soil resistances to the auger during screwing into the ground while maintaning a good load-bearing capacity for the screw displacement piles. The “DPDT-Auger” prototype was tested as a scaled-down model...
-
DISTRIBUTION OF FLOWS IN A CHANNEL NETWORK UNDER STEADY FLOW CONDITIONS
PublicationThe article presents an algorithm for calculating the distribution of flow in a junction of open channel network under steady flow conditions. The article presents a simplified calculation algorithm used to estimate the distribution of flow in a network of channels under steady flow conditions. The presented algorithm is based on the continuity equation and a simplified energy equation. To describe the relationship between the...
-
The mechanism of grouting action under the base of bored pile
PublicationThe grouting under the base of bored pile is carried out in order to reduce pile settlement and improve its bearing capacity. The principal aim of grouting is to introduce an initial force between the soil and the pile base. In non-cohesive soil, the grouting can also enlarge the pile base area and therefore improve the base resistance. The example of static load tests on instrumented bored piles installed with and without grouting...
-
Sławomir Milewski prof. dr hab. inż.
PeopleSławomir Milewski, born in 1955 in Puck, Poland, graduated in 1979 in Chemistry from the Faculty of Chemistry, Gdańsk University of Technology (GUT). In 1984 was employed at the Department of Pharmaceutical Technology and Biochemistry. In 1985 he got his PhD, in 1994 became a DSc (habilitation) and in 2002 got the professorship in chemical sciences. Currently he is a full professor and Head of the Department of Pharmaceutical Technology...
-
Investigation of the thermal effects in water-lubricated journal bearings with axial grooves
PublicationWater-lubricated hydrodynamic journal bearings are frequently applied as stern tube bearings due to their advantages over other bearing types. They are environmentally friendly, can operate without sealings and in conditions of low friction losses. The most popular are bearings with open axial grooves, which require, for proper operation, forced axial flow of the lubricating water. Correctly designed and operated stern tube bearings...
-
Evaluation of apparent Young׳s modulus of the composite polymer layers used as sliding surfaces in hydrodynamic thrust bearings
PublicationHydrodynamic bearings with a polymer sliding layer are able to operate in severe conditions, mainly due to favorable properties of the polymers. The goal of this research was to evaluate apparent Young׳s modulus of two types of the polymer composite layers used for sliding surfaces in hydrodynamic bearings, as a function of temperature. The Young׳s modulus was evaluated on the basis of compression tests carried out on samples obtained...
-
Prediction of Pile Shaft Capacity in Tension Based on Some Direct CPT Methods—Vistula Marshland Test Site
PublicationThis paper presents different CPT methodologies for the prediction of the pile shaft resistance in tension on the example of three reference screw piles of the Jazowa test site in Poland. The shaft capacity was estimated based on the cone resistance, sleeve friction and CPT excess pore water pressure. Three piles with diameter 0.4 m and the length varied from 8 m to 14.6 m were subjected to static load tests in tension. Their...
-
A comparative analysis of numerically simulated and experimentally measured static responses of a floating dock
PublicationTwo numerical methods, dynamic and static analyses, are proposed to calculate the static responses of a floating dock under different ballast water distributions. Model-scale experimental tests were conducted to compare with these numerical methods. The dynamic analysis includes a 6-degree-of-freedom (6-DOF) model, a hydrostatic force model and a hydrodynamic force model to simulate the dock's freely floating processes. The dock's...
-
Properties comparison of rubber and three layer PTFE-NBR-bronze water lubricated bearings with lubricating grooves along full bush circumference based on experimental tests
PublicationWater lubricated bearings have been in industrial use for well over a century. During the last decade their traditional range has been expanded with new, modern products. Despite that fact, certain solutions continue to employ the standard rubber bearing with lubricating grooves located along entire bush circumference. The work presents experimental research conducted on comparable sliding bearings with lubrication grooves along...
-
ANALYSIS OF THE POSSIBILITIES OF HIGH SPEED SHAFT BEARING SYSTEM DURABILITY INCREASE
PublicationDuring the operation of wind turbines with a gearbox of traditional configuration, a high failure rate of high-speed shaft bearings is observed. Such a high failures frequency is not reflected in standard bearing durability calculation methods, which can be attributed to atypical failure mechanism. To avoid observed problems in the 1.5 MW wind turbine, the modification of the existing bearing system is proposed. Multiple options,...
-
Water-Lubricated Sintered Bronze Journal Bearings—Theoretical and Experimental Research
PublicationWater lubricated bearings are used from many years in shipbuilding, hydro power and other industries because of their advantages such as: extensive serviceable life, low coefficient of friction, longevity of shaft sleeve, good abrasion resistance, low maintenance required, unit simplicity, no danger of pollution and low price. Various types of water lubricated sliding bearings have been tested at the Technical University of Gdansk...
-
Prediction of pile shaft capacity in tension based on some direct CPT methods – Vistula Marshland test site
PublicationThis paper presents different CPT methodologies for the prediction of the pile shaft resistance in tension on the example of three reference screw piles of the Jazowa test site in Poland. The shaft capacity was estimated based on the cone resistance, sleeve friction and CPT excess pore water pressure. Three piles with a diameter of 0.4 m and the length...
-
Prospects of Decreasing Power Losses in a Hydrostatic Thrust Bearing
PublicationIn numerous machines, axial load is carried by tilting pad thrust bearings known since the beginning of 20th century. These bearings are commonly bath lubricated, which is simple, does not require any additional pumps, and, due to this, such systems are highly reliable. In a contemporary technology, however, minimization of friction losses became an important goal of machinery improvement. Calculations based on elementary rules...
-
Monthly mean sea surface temperature (SST) of the Baltic Sea
Open Research DataMonthly mean sea surface temperature (SST) from 2001 to 2022 calculated from data from the SatBaltic System (https://satbaltyk.iopan.gda.pl/). The spatial resolution of the maps is 1 km. The calculation of monthly mean values at each pixel was based on four SST maps on each day of the month. The primary source of SST information was satellite data collected...
-
Vortex flow caused by periodic and aperiodic sound in a relaxing maxwell fluid
PublicationThis paper concerns the description of vortex flow generated by periodic and aperiodic sound in relaxing Maxwell fluid. The analysis is based on governing equation of vorticity mode, which is a result of decomposition of the hydrodynamic equations for fluid flow with relaxation and thermal conductivity into acoustical and non-acoustical parts. The equation governing vorticity mode uses only instantaneous, not averaged over sound...
-
Application of the ‘CPT 2012’model of AFNOR standard for column design in Poland–Jazowa case study
Publicationhis paper presents the ‘CPT 2012’ model incorporated into the AFNOR NF P94-262:2012-07, French standard for pile design fully compatible with Eurocode 7, to the wider Polish audience. The bearing capacity of three reference columns for Vistula Marshlands have been calculated according to ‘CPT 2012’ model and AFNOR recommendations. Then, the design resistances have been compared with ultimate column bearing capacity measured during...
-
Problems of analytical determination of journal bearing bush fatigue strength estimates
PublicationProblems connected with determination of stress distribution in sliding layer of thinwalled bearing bushes, investigated in bearing fatigue test rigs, have been presented. Using an example of plain bearings tested in the fatigue machine SMOK (built at the Gdask University of Technology) problems with obtaining a convergence of iterative procedure for determining the fatigue strength estimators of bearing alloy surface layer are...
-
Simulation of the number of storm overflows considering changes in precipitation dynamics and the urbanisation of the catchment area: a probabilistic approach
PublicationThis paper presents a probabilistic methodology that allows the study of the interactions between changes in rainfall dynamics and impervious areas in urban catchment on a long- and short-term basis. The proposed probabilistic model predict future storm overflows while taking into account the dynamics of changes in impervious areas and rainfall. In this model, a logistic regression method was used to simulate overflow resulting...
-
Vibro piles performance prediction using result of CPT
PublicationVibro piles belong to the group of full displacement piles with an expanded base, characterised by a very high load capacity, especially in non-cohesive soils. The problem is to adopt a reliable method for the determination of full load–settlement (Q–s) curve. A frequent difficulty is the determination of the load capacity limit based on the static load test because the course of the load–settlement curve is of a linear nature....
-
The generalized Suzuki model of the multipath fading channel
Open Research DataThe dataset contains the results of simulations that are part of the research on modelling the multipath fading in the communication channel. The generalized Suzuki fading envelope is generated using the Monte-Carlo simulation (MCS) in the LabVIEW programming environment.
-
Optimization of hydrodynamic vortex separator for removal of sand particles from storm water by computational fluid dynamics
PublicationStorm water treatment has been gradually acknowledged for the removal of pollutants from urban areas using the hydro cyclone separation technique. The separation efficiency of the hydrodynamic vortex separator (HDVS) is a complex phenomenon. With the aim enhance the separation potency of HDVS for storm runoff to get rid of sand particles, the HDVS with different structural configurations was studied by computational fluid dynamics....
-
Water uptake in protective organic coatings and its reflection in measured coating impedance
PublicationWater uptake in commercially available epoxy coating on mild steel using impedance spectroscopy and gravimetry was studied. The water content in the coating was determined using the Brasher-Kingsbury equation and various methods of coating capacitance calculation used in the literature. The obtained results were compared with reference gravimetric data. An overestimation of values obtained from impedance data in relation to gravimetric...
-
Experimental comparison of hydrodynamic thrust bearings with different pad surface materials
PublicationBabbitt is the material most frequently used as the pad surface material for hydrodynamic bearings operating at usual operating conditions. It shows many advantages important for safe bearing operation, as for example: low friction coefficient, corrosion resistance, fair mechanical properties and outstanding conformability. On the other hand, it is not free from disadvantages, such as limited fatigue strength or limited resistance...
-
Some problems of slide bearing material fatigue evaluation.
PublicationA slide bearing alloy resistance against fatigue failures have been investigated for three different lubricants, different heat loadings and different stress ratio κ values. The research methods and data handling procedures for determination of particular parameter effects on fatigue strength have been described and analysed for experiments that were set and performed in laboratory tester SKMR-2. Main and interaction effects of...
-
Numerical Estimation of Hull Hydrodynamic Derivatives in Ship Maneuvering Prediction
PublicationPrediction of the maneuvering characteristics of the ship at the design stage can be done by means of model tests, computational simulations or a combination of both. The model tests can be realized as direct simulation of the standard maneuvers with the free running model, which gives the most accurate results, but is also the least affordable as it requires very large tank or natural lake, as well as complex equipment of the...
-
The overview of reactors used for the production of precipitated calcium carbonate via carbonation route
PublicationCarbonation is one of the methods for the production of precipitated calcium carbonate (PCC) on the industrial scale. A gaseous CO2 is used as a reagent in this process. The hydrodynamic conditions gener-ated in the reactor affect the course of the process and the characteristics of the precipitated calcium carbonate particles. This paper discusses the construction of standard reactors and new proposed con-struction used for the...
-
Estimation of Screw Displacement Pile-Bearing Capacity Based on Drilling Resistances
PublicationThis article presents an engineering, empiricalmethod of estimating the bearing capacity and settlementcharacteristics Q-s of screw displacement piles andcolumns, based on soil resistance encountered during thedrilling to form piles/columns in the ground. The methodwas developed on the basis of correlation analyses of thetest results of 24 piles made during the “DPDT-Auger”research project (Krasiński et al., 2022a). In the proposedmethod,...
-
The effect of the exposure-in-oil on the contact of the polymers forming sliding layers in hydrodynamic bearings. Wpływ ekspozycji w oleju na kąt zwilżania polimerów stosowanych na warstwy ślizgowe w łożyskach hydrodynamicznych.
PublicationPolimery stosowane jako warstwy ślizgowe w hydrodynamicznych łożyskach wzdłużnych to zazwyczaj tworzywa termoplastyczne charakteryzujące się relatywnie wysokimi wartościami kątów zwilżania w porównaniu z metalami. Metale, w tym również Babbitt czy inne stopy łożyskowe, cechują niskie wartości kątów zwilżania. Im niższy kąt, tym powierzchnia lepiej się zwilża. Tworzywa sztuczne wykorzystywane w węzłach tribologicznych mających zapewnić...
-
A quasi-2D small-signal MOSFET model - main results
PublicationDynamic properties of the MOS transistor under small-signal excitation are determined by kinetic parameters of the carriers injected into the channel, i.e., the low-field mobility, velocity saturation, mobility at the quiescent-point (Q-point), longitudinal electric field in the channel, by dynamic properties of the channel, as well as by an electrical coupling between the perturbed carrier concentration in the channel and the...
-
Effect of presence of lifting pocket on the THD performance of a large tilting-pad thrust bearing
PublicationHydrostatic assistance is a commonly used method to improve limited load carrying ability of tiltingpad thrust bearings during transient states of operation of vertical shaft hydro-generators. Despite of special hydraulic equipment (as pumps, valves, etc.), it also requires manufacturing of special recesses/pockets at pad sliding surfaces, into which oil is injected under high pressure. It allows to lift the rotor before start-up...