Search
Filters
total: 229
Search results for: compression tests
-
Concrete-filled FRP tubular members in marine and bridge structures
PublicationConcrete core of the concrete-filled tubes (CFTs) with circular cross-section is in the case of an axial compression subjected to a spatial state of compressive stresses. This state leads to enhancement in the concrete strength. The enhancement is utilized in Eurocode 4 design procedures for CFSTs (i.e. CFTs with tube made of steel). The structural design of CFFTs (i.e. CFTs with tube made of Fibre Reinforced Polymer - FRP) is...
-
Quality Control for the BPG Lossy Compression of Three-Channel Remote Sensing Images
PublicationThis paper deals with providing the desired quality in the Better Portable Graphics (BPG)-based lossy compression of color and three-channel remote sensing (RS) images. Quality is described by the Mean Deviation Similarity Index (MDSI), which is proven to be one of the best metrics for characterizing compressed image quality due to its high conventional and rank-order correlation with the Mean Opinion Score (MOS) values. The...
-
Wpływ strat mechanicznych w siłowniku teleskopowym zespołu zagęszczającego w pojeździe do usuwania odpadów z pojemników na skuteczność prasowania odpadów
PublicationHydraulic telescopic cylinders are used to power the moving wall of rear loader garbage trucks equipped with the traditional "sweep and slide" system. As the garbage compression force is directly dependent on the resistance force of the moving wall, losses in the hydraulic telescopic cylinder influence the compaction process. Taking them into account in the control system may improve the operation of the compaction...
-
Analysis and assessment of the acoustic emission suitability for determination of the energy states of a tribological system in the form of a four-ball tester friction node
PublicationThe present operating safety and cost reduction requirements of the compression ignition engines make it necessary to search for new methods of detecting their defects, e.g. by the analysis of acoustic emission signals coming from the slide bearings. The paper presents non-destructive measurements of acoustic emission (AE) in order to obtain information on the processes taking place in a tribological system under the continuously...
-
On the application of magnetoelastic properties measureme nts for plastic level determination in martensitic steels
PublicationThe change in the dislocation density, induced by plastic deformation, influences strongly the magnetic domain structure inside the material. Being so, classic parameters, like the coercivity or magnetic permeability, can be a good measure of the deformation level, yet their reliable determination in a non-destructive way in industrial environment is problematic. The magnetoacoustic emission (MAE) which results from the non-180...
-
Influence of rhamnolipids and ionic cross-linking conditions on the mechanical properties of alginate hydrogels as a model bacterial biofilm
PublicationThe literature indicates the existence of a relationship between rhamnolipids and bacterial biofilm, as well as the ability of selected bacteria to produce rhamnolipids and alginate. However, the influence of biosurfactant molecules on the mechanical properties of biofilms are still not fully understood. The aim of this research is to determine the effect of rhamnolipids concentration, CaCl2 concentration, and ionic cross-linking...
-
The evaluation of the vibration measurement usability of electronic indicator lemag "premet C"
PublicationThe measuring possibilities of modern compression and combustion pressure analyzers are extended with additional functions. One of them is parallel to the pressure measurement, the measurement of vibrations in the region of the cylinder head. The paper presents a general assessment of the vibration measurement function of the electronic indicator LEMAG "PREMET C". This feature is very rarely offered by manufacturers of these devices....
-
Possibility to use engine compression ignition engines in floating power plants marine
PublicationCompression-ignition engines used in ship technology as main propulsion engines are large units reaching even to 50-60 MW. The engines can be used in power industry for electricity generation in a simple or combined steam turbine system in combined heat and power plants. The leading engine in such an arrangement is an internal-combustion piston engine. The main propulsion engines are used in large piston internal-combustion engines...
-
Feasibility of combined diesel engine - steam turbine in power station operating in the maritime
PublicationCompression-ignition engines used in ship technology as main propulsion engines are large units reaching even to 50-60 MW. Currently, the efficiency of such engines amounts to 45-50%. With such a large power unit, exhaust gases leaving the engine contain very large quantities of heat available for further treatment. Exhaust gases from the piston engine contain about 25% of the heat supplied to the engine in the fuel. Using the...
-
Towards More Realistic Probabilistic Models for Data Structures: The External Path Length in Tries under the Markov Model
PublicationTries are among the most versatile and widely used data structures on words. They are pertinent to the (internal) structure of (stored) words and several splitting procedures used in diverse contexts ranging from document taxonomy to IP addresses lookup, from data compression (i.e., Lempel- Ziv'77 scheme) to dynamic hashing, from partial-match queries to speech recognition, from leader election algorithms to distributed hashing...
-
An algorithm for enhancing macromodeling in finite element analysis of waveguide components
PublicationAn algorithm for enhancing the finite element method with local model order reduction is presented. The proposed technique can be used in fast frequency domain simulation of waveguide components and resonators. The local reduction process applied to cylindrical subregions is preceded by compression of the number of variables on its boundary. As a result,the finite element large system is converted into a very compact set of linear...
-
Numerical simulation of screw displacement pile interaction with non-cohesive soil
PublicationA trial numerical simulation of screw displacement pile interaction with non-cohesive subsoil during the transfer of compression load. The simulation was carried out in an axisymmetric system. The technological phases of pile installation in the ground were numerically modelled using equivalent processes which provided similar effects to real technical actions. The results of the numerical calculations were verified by comparing...
-
Numerical Modelling of Shear Localization in Granular Bodies using MPM and Non-local Hypoplasticity
PublicationThe paper deals with modelling of shear localization in granular bodies by means of an enhanced hypoplastic constitutive model and material point method (MPM). The calculations were carried out for plane strain compression of non-cohesive sand. In order to properly capture the width and inclination of shear zones, the constitutive model was enriched by a characteristic length of micro-structure by means of a non-local theory....
-
The Concept of a Measurement Data Acquisition Platform Based on Compressive Sensing
PublicationThe paper introduces the concept of a modern software-hardware platform for data acquisition and analysis, capable of efficiently handling vast amounts of measurement data in real time with minimal energy consumption. The current methodologies for information acquisition are predicated upon traditional sampling techniques, which frequently yield redundant data necessitating subsequent compression. The novel approach is based on...
-
Analyses of Shear Angle in Orthogonal Cutting of Pine Wood
PublicationThe determination of energy effects for wood machining processes, such as cutting power and cutting forces, is very useful in designing of manufacture process of wooden products. A more accurate prediction of cutting forces requires a correct determination of the shear angle value, which can be determined using various models. In this article, shear angle values for an orthogonal linear cutting process of pine wood are determined. The...
-
Combined cold supply system for ship application based on low GWP refrigerants - Thermo-economic and ecological analyses
PublicationThe withdrawal of popular high-GWP refrigerants will significantly affect maritime industry. Refrigeration and air conditioning systems currently used on ships are not ready to fulfil future limitations. Therefore, there is a need for system, which will operate with low-GWP refrigerants and at the same time will be efficient and reliable in difficult environmental conditions. This paper explains the concept of a cold supply system,...
-
Local dynamics of fluids and dielectrics as the foundation of signal-carrying wave properties
PublicationThis paper develops an original approach to fundamental problems of classical linear acoustics and electromagnetics, proving a crucial role of doubly-dynamic local properties of a propagation medium in supporting wave-like fields able to carry information signals. The proof is composed of two steps concerning, subsequently, fluid acoustics and dielectric electromagnetics. The first step consists in complementing a common, practically...
-
Evaluation of compression realization in diesel engine based on performance indicator changes
PublicationIn the article a method of evaluation of a diesel engine during the realization of processes of working cycle on the example of compression is described. The method is based on the use of the quantity called performance indicator in the description of the engine's work, which contains the information on the energy values, which may be disposed using the engine and the time at which it can be delivered. Theoretical information has...
-
Computations of critical load value of composite shell with random geometric imperfections
PublicationThe work presents the numerical analysis of composite shell with geometric imperfections subjected to compression along its generatrix. The imperfections are described as single indentations and random fields with random parameters of shape and correlation. The fields are generated with the use of the authors made program. Using the authors’ FEM software as well as commercial package Femap with NX Nastran, the critical load values...
-
LEGAL ASPECTS OF ELECTRIC ENERGY GENERATION IN A FLOATING POWER PLANT
PublicationThis paper discusses the characteristics of pollution and legal regulations governing investment projects affecting the environment. It describes a combined system of a compression ignition engine and a steam turbine, whose aim, when placed on a floating platform, is to produce electric energy in a so-called distributed generation system. Such a system involves a reciprocating internal combustion engine and a connected steam turbine...
-
The forming and emission of high power electromagnetic pulses
PublicationAn impulse energy source, a power conditioning system and an electromagnetic field emitter are essential to generate an electromagnetic field pulse (EMFP) with a specific frequency bandwidth. Selected simulation results for a power conditioning system consisting of a fuse opening switch and a paraboloidal electromagnetic emitter have been presented in this article. The synthetic system examined in the simulation is powered by an...
-
The Dominant Influence of Plastic Deformation Induced Residual Stress on the Barkhausen Effect Signal in Martensitic Steels
PublicationThe paper presents the results of investigation of the influence of plastic deformation on the magnetic properties of martensitic steel (P91 grade). The properties of the hysteresis loops as well as of the Barkhausen effect (BE) signal are analysed for both tensile and compressive loading up to ε = 10% of plastic deformation. The choice of the steel and of the deformation range is unique, since for such combination one can expect...
-
The forming and emission of high power electromagnetic pulses
PublicationAn impulse energy source, a power conditioning system and an electromagnetic field emitter are essential to generate an electromagnetic field pulse (EMFP) with a specific frequency bandwidth. Selected simulation results for a power conditioning system consisting of a fuse opening switch and a paraboloidal electromagnetic emitter have been presented in this article. The synthetic system examined in the simulation is powered by...
-
Wireless intelligent audio-video surveillance prototyping system
PublicationThe presented system is based on the Virtex6 FPGA and several supporting devices like a fast DDR3 memory, small HD camera, microphone with A/D converter, WiFi radio communication module, etc. The system is controlled by the Linux operating system. The Linux drivers for devices implemented in the system have been prepared. The system has been successfully verified in a H.264 compression accelerator prototype in which the most demanding...
-
Rigid polyurethane foams modified with selected flame retardants
PublicationThe flame retardants: expandable graphite, triethylphosphatehas been used in rigid polyurethane foams (PUFs). The influence of fillers amounts on processing parameters, physical-mechanical properties (compression strength, density, water absorption, brittleness)and thermal properties (thermal stability) of such foams has been analyzed.The gel, cram and rise time for PUFs modified with flame retardant has been observed during synthesis...
-
Preparation, morphology and properties of natural rubber composites filled with untreated short jute fibres
PublicationGreen composites were obtained by incorporation of short jute fibres in natural rubber matrix using a laboratory two-roll mill. The influence of untreated fibre content (1, 2.5, 5, 7.5 and 10 phr) on the mechanical properties, dynamic mechanical properties, swelling properties was examined. The behaviour of prepared green composites under cyclic compression was also investigated. Fibre dispersion in rubber matrix was studied by...
-
Solvation phenomena in ternary system tetramethylurea-methylacetamide-water: Insights from volumetric, compressibility and FTIR analysis
PublicationThe properties of the ternary systems N,N,N’,N’-tetramethylurea - N-methylacetamide - water were investigated using Fourier-transform infrared spectroscopy (FTIR), volumetric and compression measurements. Densities and sound velocities were determined in order to obtain the apparent molar volumes (VΦ) and apparent molar isentropic compressions (ΚS,Φ). These values were then extrapolated to infinite dilution. Additionally, interaction parameters...
-
Smaller Representation of Finite State Automata
PublicationThis paper is a follow-up to Jan Daciuk's experiments on space-effcient finite state automata representation that can be used directly for traversals in main memory. We investigate several techniques of reducing memory footprint of minimal automata, mainly exploiting the fact that transition labels and transition pointer offset values are not evenly distributed and so are suitable for compression. We achieve a gain of around 20-30%...
-
Force-deformation spectroscopy in contact mode
Open Research DataThe deformation-distance spectroscopic curve is obtained by registering the value of the probe cantilever deflection as a function of the elongation of the piezoelectric scanner. It assumes a simple relationship in the form of Hooke’s law, linking the deformation of the lever with the amount of its deflection caused by the proximity of the probe and...
-
A procedure for elastoplastic hardening function identification.
PublicationThe inverse analysis method for identifying a nonlinear hardening function,which governs a plastic yielding of soil and rock materials in the framework of elastoplastic theory is presented. A concept of two stage finite element based on spatial discretization of computational space and hardening function space is introduced. The proposed inverse analysis can be classified as the output least squares method. The Levenberg Marquard...
-
Robust and Efficient Machine Learning Algorithms for Visual Recognition
PublicationIn visual recognition, the task is to identify and localize all objects of interest in the input image. With the ubiquitous presence of visual data in modern days, the role of object recognition algorithms is becoming more significant than ever and ranges from autonomous driving to computer-aided diagnosis in medicine. Current models for visual recognition are dominated by models based on Convolutional Neural Networks (CNNs), which...
-
Smaller representation of finite state automata
PublicationThis paper is a follow-up to Jan Daciuk's experiments on space-efficient finite state automata representation that can be used directly for traversals in main memory (Daciuk, 2000)[4]. We investigate several techniques for reducing memory footprint of minimal automata, mainly exploiting the fact that transition labels and transition pointer offset values are not evenly distributed and so are suitable for compression. We achieve...
-
Thermodynamic analysis of the Compressed Air Energy Storage system coupled with the Underground Thermal Energy Storage
PublicationImprovement of flexibility is one of the key challenges for the transformation of the Polish Power System aiming at a high share of renewable energy in electricity generation. Flexible and dispatchable power plants will contribute to this ongoing transformation process as they compensate for fluctuations in electricity generation from renewable energy sources such as wind and photovoltaics. In this context, CAES storage tanks are...
-
Validation of lumbar spine finite element model
Open Research DataThe functional biomechanics of the lumbar spine have been better understood by finite element method (FEM) simulations. However, there are still areas where the behavior of soft tissues can be better modeled or described in a different way. The purpose of this research is to develop and validate a lumbar spine section intended for biomechanical research....
-
Analysis of impact of audio modifications on the robustness of watermark for non-blind architecture
PublicationThe aim of this paper is to assess the robustness of the non-blind audio content watermarking scheme proposed by the authors. The authors present the architecture of the designed system along with the employed workflows for embedding and extracting the watermark followed by the implementation phase description and the analysis of the experimental results. Some possible attack simulations on the embedded watermarks are reviewed,...
-
Average Size of a Suffix Tree for Markov Sources
PublicationWe study a suffix tree built from a sequence generated by a Markovian source. Such sources are more realistic probabilistic models for text generation, data compression, molecular applications, and so forth. We prove that the average size of such a suffix tree is asymptotically equivalent to the average size of a trie built over n independentsequences from the same Markovian source. This equivalenceis only known for memoryless...
-
Te use of acoustic emission for assessment of the oil lubricity in a four-ball tester
Publicationin view of the increased dynamic and temperature load in the compression-ignition engine tribological systems, particular attention is drawn to the problem of such lubrication of the friction nodes that after breaking the boundary layer it could be restored without any wear occurring. therefore, an idea has been devised of introducing to friction nodes, with the lubrication oils, of new substances (operational preparations) modifying...
-
rigid polyurethane foams modified with selected nanofillers
PublicationThe nanofillers: natural montmoryllonite (MMT) - Bentonite, natural MMT modified with a quaternary ammonium salt - Cloisite30B, has been used in rigid polyurethane foams (PUFs). The influence of fillers amounts on processing parameters, physical-mechanical properties (density, water absorption, brittleness and compression strength) and thermal properties (thermal stability, fire behaviours) of such foams has been analysed. The...
-
Stability and limit load analysis of a cold-formed channel section column
PublicationThe paper presents stability and limit load analysis of a steel column 1440 mm high of a cold-formed channel section, subjected to a combination of compression and bending. Experimental results were compared to the resistance of a code procedure and to the outcome of numerical non-linear analysis. Comparison was made of numerical solutions by means of static (Riks) and dynamic (Explicit and Implicit) methods. Perfectly elastic...
-
Continuum models for pantographic blocks with second gradient energies which are incomplete
PublicationWe postulate a deformation energy for describing the mechanical behavior of so called pantographic blocks, that is bodies constituted by stacking of layers of pantographic sheets. We remark that the pantographic effect is limited in the plane of pantographic sheets and therefore only the second derivatives of transverse displacements along the pantographic fibers appear in the chosen deformation energy. We use this novel energy...
-
Time variable gain for long range sonar with chirp sounding signal
PublicationThe main purpose of applaying Time Variable Gain (TVG) in active sonars with digital signal processing is to reduce dynamic range of echo signal and adapt it to the dynamic range of the analogue to digital conversion. With high transmission losses level, the dynamic range of the input signal in long range sonars can be very high and even exceed 200dB. When chirp sounding signals with matched filtration are used, sonars can raech...
-
Analysis of impact of lossy audio compression on the robustness of watermark embedded in the DWT domain for non-blind copyright protection
PublicationA methodology of non-blind watermarking of the audio content is proposed. The outline of audio copyright problem and motivation for practical applications are discussed. The algorithmic theory pertaining watermarking techniques is briefly introduced. The system architecture together with employed workflows for embedding and extracting the watermarks are described. The implemented approach is described and obtained results are reported....
-
Microstructure, mechanical properties, and flame retardancy of nanoclay-incorporated polyurethane flexible foam composites
PublicationThe present work seeks to investigate microstructure, mechanical properties, and flame retardancy of polyurethane/nanoclay flexible foam composites. In this regard, we prepared various nanocomposites with and without nanoclay and observed the resulting morphologies to correlate them with the other corresponding characteristics. The results provided support for the fact that tensile strength and compression set will increase with...
-
Processing of Polyester-Urethane Filament and Characterization of FFF 3D Printed Elastic Porous Structures with Potential in Cancellous Bone Tissue Engineering
PublicationThis paper addresses the potential of self-made polyester-urethane filament as a candidate for Fused Filament Fabrication (FFF)-based 3D printing (3DP) in medical applications. Since the industry does not provide many ready-made solutions of medical-grade polyurethane filaments, we undertook research aimed at presenting the process of thermoplastic polyurethane (TPU) filament formation, detailed characteristics, and 3DP of specially...
-
Local buckling of compressed flange of cold-formed channel members made of aluminum alloy
PublicationThe paper deals with local buckling of a compressed single flange of thin-walled channel cold- formed columns and beams made of aluminum alloy. Material is described by means of the Ramberg-Osgood constitutive equation. Axial compression of the columns and beams undergoing bending is taken into consid- eration. A simple model of the member flange in the form a long beam elastically connected to the web is used to find the critical...
-
Orientation effects on the fracture behaviour of additively manufactured stainless steel 316L subjected to high cyclic fatigue
PublicationIn this paper, stainless steel 316L (SS316L) bars were additively manufactured (AM) in three orientations (Z – vertical, XY – horizontal, ZX45 – midway between vertical and horizontal) by using the Laser Powder Bed Fusion Melting (LPBF-M) method. The AM specimens were subjected to load control fatigue testing under full tension and compression (R = -1) at stress amplitudes ±350, ±400 and ±450 MPa. The XY and ZX45 printing orientations...
-
High-Speed Serial Embedded Deterministic Test for System-on-Chip Designs
PublicationThe paper presents a high-speed serial interface between external tester and Embedded Deterministic Test (EDT) compression logic hosted by SoC designs. With only a single bidirectional link, the system is capable of feeding distributed heterogeneous cores with hundreds of test channels. Moreover, it synergistically supports EDT bandwidth management to improve the overall test performance. A detailed study indicates a high potential...
-
The hydration of the protein stabilizing agents: trimethylamine-N-oxide, glycine and its N-methylderivatives - the volumetric and compressibility studies
PublicationThe densities at T = (288.15, 293.15, 298.15, 303.15, and 308.15) K and sound velocities at T = 298.15 K have been measured for aqueous solutions of trimethylamine-N-oxide, glycine, N-methylglycine (sarcosine), N,N-dimethylglycine, N,N,N-trimethylglycine (betaine). From these data the apparent molar volumes, VΦ, the apparent molar isentropic compressions, KS,Φ, and the solvation numbers of solutes have been determined. The concentration...
-
Buckling Analysis of a Micro Composite Plate with Nano Coating Based on the Modified Couple Stress Theory
PublicationThe present study investigates the buckling of a thick sandwich plate under the biaxial non-uniform compression using the modified couple stress theory with various boundary conditions. For this purpose, the top and bottom faces are orthotropic graphene sheets and for the central core the isotropic soft materials are investigated. The simplified first order shear deformation theory (S-FSDT) is employed and the governing differential...
-
Application of the near-infrared spectroscopy in the pharmaceutical technology
PublicationNear-infrared (NIR) spectroscopy is currently the fastest-growing and the most versatile analytical method not only in the pharmaceutical sciences but also in the industry. This review focuses on recent NIR applications in the pharmaceutical technology. This article covers monitoring, by NIR, of many manufacturing processes, such as granulation, mixing or drying, in order to determine the end-point of these processes. In this...