Search results for: DISPLACEMENT AND FIRING MAP
-
Wave propagation signals in concrete beams under 3-point bending
Open Research DataThe DataSet contains the results of the mechanical behaviour of a concrete beams with dimensions 40 x 40 x 160 cm3under the 3-point bending. The beams were made of concrete with the following ingredients: CEM I 42.5R (450 kg/m3), water (177 kg/m3), sand 0-2 (675 kg/m3) and gravel 2-8 (675 kg/m3). The bending test was performed using a Zwick/Roell Z10...
-
Numerical FDM modelling of wave propagation in concrete structure
PublicationThe article presents application of finite difference method to damage detection and its size evaluation in concrete structure by elastic wave propagation method. The simulations of wave propagation in concrete structure were performed for six different damage scenarios. Damages were modelled as areas with changed material properties. Investigation focused on the influence of damage size on the energy of wave reflection. Presented...
-
Reduction of Derivative pipeline effort in water turbine
PublicationThe paper presents an approach to evaluate and reduce the effort of the derivative pipeline in a water turbine of a hydrostatic power station in its vulnerable spots. Potential places of the biggest effort of the structure, as well as the coefficient of displacement and safety factor related to them were identified using FEM numerical method. Pipeline reinforcement was designed and made based on FEM analysis. Original technology...
-
In-plane shear nonlinearity in failure behavior of angle-ply laminated shells
PublicationThe paper concerns the progressive failure analysis of laminates with the in-plane shear nonlinearity accounted for.The nonlinear shear response of the layer is described by the constitutive relation treating the stresses as a function of strains. Thus it can be easily incorporated into the displacement-based FEM codes. The brittle failure mechanisms of the fibers and the matrix of the layer are recognized with the use of the Hashin...
-
Small rov to detection and identification of dangerous underwater objects
PublicationA small unmanned underwater vehicle (UUV) to inspection of an undersea space is presented in the paper. Its behavior is controlled by a trained pilot. Correct detection and identification of targets depends on vehicle'sprecise displacement along a predefined route. Nowadays, the UUVs are equipped with an automatic control system to execute some basic maneuvers without constant human interventions. Hence, in the paper, an autopilot...
-
Interictal high-frequency oscillations in focal human epilepsy
PublicationPURPOSE OF REVIEW: Localization of focal epileptic brain is critical for successful epilepsy surgery and focal brain stimulation. Despite significant progress, roughly half of all patients undergoing focal surgical resection, and most patients receiving focal electrical stimulation, are not seizure free. There is intense interest in high-frequency oscillations (HFOs) recorded with intracranial electroencephalography as potential...
-
Data on bicycle traffic in Lodz (Poland) paired with weather and air quality data
Open Research DataThe file contains data on bicycle traffic registered by counting stations loacted in Lodz in the years 2016-2019. The data are paired with weather and air quality data from Lodz collected for the same period. The data is described below:
-
Data on bicycle traffic in Gdansk paired with weather and air quality data
Open Research DataThe file contains data on bicycle traffic registered by counting stations loacted in Gdańsk in the years 2013-2020. The data are paired with weather and air quality data from Gdansk collected for the same period. The data is described below:
-
Praktyczne zastosowania analizy wrażliwości na przykładzie projektowania tarczy
PublicationW pracy przedstawiono przykłady zastosowania analizy wrażliwości przy projektowaniu tar-czy. Badano wpływ zmian grubości obszarów tarczy – zmiennej projektowej – na przemiesz-czenie wybranego punktu tarczy – zmiennej stanu. Zaproponowano metodę projektowania polegającą na zwiększeniu grubości obszarów tarczy, których wpływ na wariację zmiennej stanu (wrażliwość) jest największa. Do obliczeń numerycznych korzystano z metody elemen-tów...
-
Spatial and seasonal patterns of benzene, toluene, ethylbenzene, and xylenes in the Gdańsk, Poland and surrounding areas determined using Radiello passive samplers
PublicationCelem badań było uzyskanie informacji o poziomie zanieczyszczeń powietrza atmosferycznego przez związki z grupy BTEX na terenie aglomeracji Trójmiejskiej z wykorzystaniem techniki dozymetrii pasywnej na etapie pobierania próbek analitów. Próbniki pasywne Radiello były poddawane ekspozycji na stacjach pomiarowych zarządzanych przez fundację ARMAAG, zlokalizowanych na terenie aglomeracji Trójmiejskiej.Otrzymane informacje analityczne...
-
Cartographic Representation of Route Reconstruction Results in Video Surveillance System
PublicationThe video streams available in a surveillance system distributed on the wide area may be accompanied by metadata are obtained as a result of video processing. Many algorithms applied to surveillance systems, e.g. event detection or object tracking, are strictly connected with localization of the object and reconstruction of its route. Drawing related information on a plan of a building or on a map of the city can facilitate the...
-
Analiza numeryczna propagacji fali elektromagnetycznej w konstrukcji podłogi posadowionej na gruncie
PublicationPopularną techniką wspomagającą interpretację map georadarowych jest modelowanie numeryczne propagacji pola elektromagnetycznego z użyciem metody różnic skończonych w dziedzinie czasu (FDTD). W pracy przedstawiono analizy numeryczne przeprowadzone dla konstrukcji podłogi posadowionej na gruncie, która wcześniej została poddana badaniom metodą georadarową. Przeanalizowano modele numeryczne dla konstrukcji idealnej oraz uszkodzonej....
-
Influence of an Interview Location on Opinions about the Ecosystem Services Provided by Trees
PublicationCollecting opinions regarding environmental management is essential, particularly in urban areas where space is limited, and interests often collide. However, the impact of the conditions in which the research is conducted on opinions and preferences elicited via surveys and interviews about the environment is usually taken for granted. The recent development of computer-aided survey methods allows a simulation of an environment,...
-
Pedestrian detection in low-resolution thermal images
PublicationOver one million people die in car accidents worldwide each year. A solution that will be able to reduce situations in which pedestrian safety is at risk has been sought for a long time. One of the techniques for detecting pedestrians on the road is the use of artificial intelligence in connection with thermal imaging. The purpose of this work was to design a system to assist the safety of people and car intelligence with the use...
-
Green strength (buildability performance) of concretes containing magnetite aggregate (M0-M100) mixes
Open Research DataRaw data for determination of buildability (green strength) properties of concrete mixes determined by squeezing test using QuantumX MX840B with CATMAN-EASY software, determined after 15, 30, 45 and 60 minutes. Values present force and two displacement measurements by LVDT.Additionally, an Origin (*.opju) file with processed data presenting stress-strain...
-
COMMENTS ON EXISTING ANALYTICAL SOLUTIONS TO THE WAVE-INDUCED CYCLIC RESPONSE OF A POROUS SEABED OF INFINITE THICKNESS
PublicationThis paper deals with the wave-induced cyclic response of a porous seabed (by means of oscillating parameters: pore-fluid pressure, soil displacement components, effective normal stress and shear stress components) due to a surface sinusoidal water-wave propagating over a seabed of infinite thickness. The main existing analytical solutions to the governing problem are critically discussed, pointing out their meaningful errors and...
-
Analysis of spatial changes in the town of Puck with its surroundings in the years 1926, 1940, 1974, 1985, 2000, 2020 on the basis of topographic maps using the BDOT10K database
Open Research DataSpatial changes over time are extremely valuable due to the possibility of modeling forecasts. This dataset shows how Puck has evolved over a specific period of time. Thanks to this presentation of the data set, it is possible to easily recreate the appearance of the city in particular years.
-
Drilling couples and refined constitutive equations in the resultant geometrically non-linear theory of elastic shells
PublicationIt is well known that distribution of displacements through the shell thickness is non-linear, in general. We introduce a modified polar decomposition of shell deformation gradient and a vector of deviation from the linear displacement distribution. When strains are assumed to be small, this allows one to propose an explicit definition of the drilling couples which is proportional to tangential components of the deviation vector....
-
Optimum number of actuators to minimize the cross-sectional area of prestressable cable and truss structures
PublicationThis paper describes a new computational method for determining the optimum number of actuators to design the optimal and economic cross-sectional area of pin-jointed assemblies based on the conventional force method. The most active members are selected to be prestressed to redistribute stress in the whole structure, resulting in regulating the internal force of bars that face high stress. Reducing stress in critical members allows...
-
Optimum shapes and dimensions of rubber bumpers in order to reduce structural pounding during seismic excitations
PublicationLarge displacement of structures observed during seismic excitations may lead to collisions between two adjacent, insufficiently-separated buildings and may result in major damages of both of them. In many building codes, appropriate equations or approximately recommended distances between structures in order to avoid pounding hazard have been introduced. Unfortunately, further, more detailed considerations show that safety situation...
-
Partycypacja społeczeństwa informacyjnego w kształtowaniu przestrzeni współczesnego miasta/ Participation of the information society in the modern city creation
PublicationNiesłabnąca popularność narzędzi służących do kreowania map świadczy o zainteresowaniu społeczeństwa informacyjnego przestrzenią współczesnego miasta i zmianami w niej zachodzącymi. W artykule zostaną omówione nowe możliwości jakie daje ten rodzaj partycypacji. Podkreślony zostanie fakt, iż oddolne inicjatywy digitalizowania przestrzeni nie powinny być ignorowane przez profesjonalistów, gdyż tworzy się nowa przestrzeń dyskusji...
-
Minimal number of periodic points of smooth boundary-preserving self-maps of simply-connected manifolds
PublicationLet M be a smooth compact and simply-connected manifold with simply-connected boundary ∂M, r be a fixed odd natural number. We consider f, a C1 self-map of M, preserving ∂M . Under the assumption that the dimension of M is at least 4, we define an invariant Dr(f;M,∂M) that is equal to the minimal number of r-periodic points for all maps preserving ∂M and C1-homotopic to f. As an application, we give necessary and sufficient...
-
Intelligent Autonomous Vehicles
PublicationAdvanced mobile vehicles and robots have long been one of the main issues in engineering. They have various applications in emergency, lifeguarding and entertainment as well as in various industrial, civil and military systems. Among them, you can distinguish robots that can move in an open environment or operate only in predetermined confined spaces. Open world robots are very demanding because they have...
-
Bending test results of first metatarsophalangeal joint after arthrodesis with medially or dorsally positioned locking plate and lag screw.
Open Research DataThe Dataset contains the results of the bending test of first metatarsophalangeal (MTP1) joint specimens after arthrodesis.
-
Jakub Jabłoński inż.
PeopleEducation In 2016 Jakub Jabłoński finished Zbigniew Herbert XX High School in Gdańsk (math-physics-IT profile). In 2017 he started an undergraduate course in Civil Engineering at the Faculty of Civil and Environmental Engineering of the Gdańsk University of Technology, which he graduated in 2021 with the title of Bachelor of Science in Engineering. During his studies he took active part in the scientific association "Hevelius". Employment About...
-
Results of nanoindentation test to calculate residual stress in an eyelet of undercarriage drag strut after laser treatment
Open Research DataIn order to determine the residual stress in the laser-processed an eyelet of undercarriage drag strut, a nanoindentation test was performed before and after stress relief annealing. For this purpose, after the hardness test, the sample was subjected to stress relief annealing at 270 °C for 2 hours. Annealing was performed in a vacuum furnace. Hardness...
-
Direct design of Controlled Modulus Columns (CMC) based on in-situ testing
PublicationIn this paper, the serviceability limit state and bearing capacity of tension screw displacement piles were analyzed using the results of static pile load tests, carried out on the test plot near the Elbląg city, and field, and laboratory tests. The paper presents the methodology of determining the pile load-settlement curve using different types of t-z transfer functions. The new method of constructing the pile load-settlement...
-
Numerical modelling and experimental verification of compressible squeeze film pressure
PublicationThe validity of using the Reynolds equation for compressible squeeze film pressure was tested with computational fluid dynamics (CFD). A squeeze film air bearing was instrumented with pressure sensors and non-contacting displacement probes to provide transient measurements of film thickness and pressure. The film thickness measurements also provided input parameters to the numerical prediction. However, numerical results showed...
-
FEM simulation of laminate failure in the three point bending
PublicationThe paper presents a FEM simulation of failure of laminate subjected to the three point bending. The numeri-cal model is based on the equivalent single layer approach with 6-paramater non-linear shell theory kinematics. It is implemented in the non-commercial FEM code. The failure initiation is detected with the use of Tsai-Wu criterion. After the failure onset the progressive failure process is modelled through the appropriate...
-
Monitorowanie i mapowanie zanieczyszczeń powietrza atmosferycznego aglomeracji trójmiejskiej związka z grupy BTEX
PublicationJedną z technik analitycznych wykorzystywanych na etapie pobierania próbek analitów w monitoringu zanieczyszczeń powietrza jest dozymetria pasywna. Współpracując z fundacją ARMAAG podjęto próbę uzupełnienia informacji na temat zawartości analitów z grupy BTEX na terenie Trójmiasta i Tczewa. Celem badań jest uzyskanie informacji o poziomie zanieczyszczeń z grupy BTEX z wykorzystaniem techniki dozymetrii pasywnej na etapie pobierania...
-
Evolutionary optimization of combinational digital circuits with current-mode gates with respect to transistor count
PublicationW artykule przedstawiono metodę ewolucyjnej minimalizacji liczby tranzystorów w cyfrowym układzie kombinacyjnym, zrealizownaym z wykorzystaniem bramek pracujących w trybie prądowym. W zastosowanym algorytmie ewolucyjnym zastosowano chromosomy o budowie wielowarstwowej, przez co zwiększono wydajność optymalizacji. Wyniki otrzymane z wykorzystaniem proponowanej metody zostały porównane z rezultatami osiągniętymi za pomocą map Karnough...
-
RF Indoor Positioning System Supported by Wireless Computer Vision Sensors
PublicationIn this paper the possibility of increase the accuracy of RF fingerprinting indoor tracking system by the use of additional information from simple vision system is examined. As the distances in signal space differs from ones in real environment the ambiguity in decision process of fingerprinting algorithm can occur when set of closest distances between tag and map points in signal space corresponds to big distances differences...
-
Minimization of the number of periodic points for smooth self-maps of simply-connected manifolds with periodic sequence of Lefschetz numbers
PublicationLet f be a smooth self-map of m-dimensional, m ≥ 4, smooth closed connected and simply-connected manifold, r a fixed natural number. For the class of maps with periodic sequence of Lefschetz numbers of iterations the authors introduced in [Graff G., Kaczkowska A., Reducing the number of periodic points in smooth homotopy class of self-maps of simply-connected manifolds with periodic sequence of Lefschetz numbers, Ann. Polon. Math....
-
Accuracy analysis of the RSSI BLE SensorTag signal for indoor localization purposes
PublicationIn this paper we describe possibility of use the RSSI signal (Radio Signal Strength Indication) from Texas Instruments SensorTag CC2650 for indoor positioning purposes. This idea is not a new but in our opinion it is possible to use SensorTags with Bluetooth LE wireless interface for positioning inside buildings in such applications as people findings in hospitals, senior come care, etc. RSSI is mostly selected as the sensor localization...
-
An algorithmic approach to estimating the minimal number of periodic points for smooth self-maps of simply-connected manifolds
PublicationFor a given self-map f of M, a closed smooth connected and simply-connected manifold of dimension m 4, we provide an algorithm for estimating the values of the topological invariant D^m_r [f], which equals the minimal number of r-periodic points in the smooth homotopy class of f. Our results are based on the combinatorial scheme for computing D^m_r [f] introduced by G. Graff and J. Jezierski [J. Fixed Point Theory Appl. 13 (2013),...
-
Zastosowanie georadaru do badań muru ceglanego
PublicationPostęp technologiczny w dziedzinie diagnostyki konstrukcji badaniami nieniszczącymi NDT (z ang. nondestructive testing) pozwala na coraz dokładniejsze określenie stanu technicznego danej konstrukcji. Jedną z tego rodzaju technik jest metoda georadarowa należąca do grupy metod elektromagnetycznych. Wykorzystuje ona zjawisko odbicia fali elektromagnetycznej na granicy ośrodków o różnych właściwościach elektrycznych. Metoda znalazła...
-
Dynamic impedance spectra of programmable dynamically changing RC model based on digital potentiometers
Open Research DataThe dataset presents non-stationary impedance spectra of the RC model presented in the figure below. This model contains two digital potentiometers controlled digitally by the microcontroller. This solution allows to programmably control the value of the model impedance. Thanks to this, the model can be used as a test engine for evaluation of the dynamic...
-
The generalization by simplification operator with Sester’s method of objects representing groups of buildings in Gdańsk district - scale 1:10000. Data from OSM
Open Research DataThe process of automatic generalization is one of the elements of spatial data preparation for the purpose of creating digital cartographic studies. The presented data include a part of the process of generalization of building groups obtained from the Open Street Map databases (OSM) [1].
-
On the modelling of aerodynamic force coefficients for over-shroud seals of turbine stages
PublicationThis paper presents experimental investigations which made it possible to determine dynamic coefficients of labyrinth over-shroud seal of a model air turbine. The coefficients associate pressure forces with turbine rotor displacement, velocity and acceleration respective to turbine casing (linear model) and play important role in analyzing turbine-set dynamics. The obtained results indicated that involving serious errors can be...
-
Usage of concentrated spectrogram for analysis of acoustical signals
PublicationA novel precise method of signal analysis in the time-frequency domain is presented. A signal energy distribution is estimated by discard and displacement of energy parts of the classical spectrogram. A channelized instantaneous frequency and a local group delay are used in order to energy replacement. Additionally, newly introduced representations such as: a channelized instantaneous bandwidth and a local group duration are used...
-
Calculation of an ultimate load value of a silo with geometric imperfections in the shape of eigenforms
PublicationThe ultimate load value of a silo with initial geometric imperfections was measured. The structure was loaded with wind. Imperfections were assumed as translations of the shell nodes from perfect geometry taken from eigenforms and their combinations. Two variants of the maximum deflection placement with respect to the direction of wind pressure were proposed. The first consists in applying the maximum wind pressure to the element...
-
A novel method of time-frequency analysis: an essential spectrogram
PublicationA novel precise method of time-frequency analysis is presented. In the algorithm, a new energy distribution is estimated by simultaneously discard or displacement of the classical spec- trogram energy. A channelized instantaneous frequency and a local group delay are used in order to replacement in the same manner as formulated by Kodera et al. [1, 2]. Additionally, new representations: a channelized instantaneous bandwidth and...
-
Shielded coupled strip and slot guides with a thin omega pseudochiral medium layer
PublicationA method of moments combined with mode matching technique is applied to analyze the shielded coupled strip and slot line structures containing a thin plate of Omega pseudochiral medium. The boundary problems are simplified by introducing for omega medium the approximate continuity conditions. Such mathematical model allows to examine the field displacement effect appearing in the considered guide resulting from the coupling between...
-
Influence of an applied bearing system on behaviour of multi-span footbridge
PublicationThe cycle overpass in Gdynia is a box structure over 300 metres long, 10-span. It was opened for bicycle traffic in the second half of 2013. At the end of its construction, there was failure due to excessive horizontal displacement of the system. A number of bearings exceeded the range of permissible transverse shifts thus it was necessary to temporarily protect the spans from slipping. The FEM analysis of the original solution...
-
Buckling analysis of a non-concentric double-walled carbon nanotube
PublicationOn the basis of a theoretical study, this research incorporates an eccentricity into a system of compressed double-walled carbon nanotubes (DWCNTs). In order to formulate the stability equations, a kinematic displacement with reference to the classical beam hypothesis is utilized. Furthermore, the influence of nanoscale size is taken into account with regard to the nonlocal approach of strain gradient and the van der Waals interaction...
-
Ultrasonic wave propagation and digital image correlation measurements of polyolefin fibre-reinforced concrete beams under 3-point bending (beam B-002)
Open Research DataThe DataSet contains the results of the mechanical behaviour of a concrete beam under a 3-point bending test. The beams had dimensions 15 x 15 x 70 cm3. The beam B-Con was made of concrete without fibres (as the reference beam), while beams B-002, B-004, and B-006 were manufactured from the concrete mix containing 2 kg/m3, 4 kg/m3 and 6 kg/m3 of fibres,...
-
Ultrasonic wave propagation and digital image correlation measurements of polyolefin fibre-reinforced concrete beams under 3-point bending (beam B-Con)
Open Research DataThe DataSet contains the results of the mechanical behaviour of a concrete beam under a 3-point bending test. The beams had dimensions 15 x 15 x 70 cm3. The beam B-Con was made of concrete without fibres (as the reference beam), while beams B-002, B-004, and B-006 were manufactured from the concrete mix containing 2 kg/m3, 4 kg/m3 and 6 kg/m3 of fibres,...
-
Ultrasonic wave propagation and digital image correlation measurements of polyolefin fibre-reinforced concrete beams under 3-point bending (beam B-004)
Open Research DataThe DataSet contains the results of the mechanical behaviour of a concrete beam under a 3-point bending test. The beams had dimensions 15 x 15 x 70 cm3. The beam B-Con was made of concrete without fibres (as the reference beam), while beams B-002, B-004, and B-006 were manufactured from the concrete mix containing 2 kg/m3, 4 kg/m3 and 6 kg/m3 of fibres,...
-
Ultrasonic wave propagation and digital image correlation measurements of polyolefin fibre-reinforced concrete beams under 3-point bending (beam B-006)
Open Research DataThe DataSet contains the results of the mechanical behaviour of a concrete beam under a 3-point bending test. The beams had dimensions 15 x 15 x 70 cm3. The beam B-Con was made of concrete without fibres (as the reference beam), while beams B-002, B-004, and B-006 were manufactured from the concrete mix containing 2 kg/m3, 4 kg/m3 and 6 kg/m3 of fibres,...
-
Medially positioned plate in first metatarsophalangeal joint arthrodesis
PublicationObjective The purpose of this study was to biomechanically compare the stability of first metatarsophalangeal (MTP1) joint arthrodesis with dorsally and medially positioned plates. Methods A physical model of the MTP1 joint consists of printed synthetic bones, a titanium locking plate and screws. In the experiments, samples with dorsally and medially positioned plates were subjected to loading of ground load character in a universal...