Search
Search results for: GROUND%20TIRE%20RUBBER
-
THE IMPACT OF GROUND TIRE RUBBER TREATMENT ON THE THERMAL CONDUCTIVITY OF FLEXIBLE POLYURETHANE/GROUND TIRE RUBBER COMPOSITES
PublicationWaste car tires are burdensome waste, and their utilization is crucial for the natural environment. In many countries, the primary method of their recycling is energy recovery, performed by simple combustion. However, material recycling is much more effective and significantly more beneficial for the natural environment. It results in the generation of ground tire rubber, which can be used to produce polymerrubber composites. It...
-
Influence of the shoe type on the ground reaction forces
PublicationThe aim of this work was to estimate a relationship between the type of the footwear and ground reactions. Differences in medio-lateral, anterior-posterior and vertical reactions are compared for different shoe-types for male and female volunteers. Each of the participants gait was recorded in case of different shoes and without them, also stabilograms were analyzed. Results revealed differences in ground reaction forces for different...
-
Wave propagation in damage assessment of ground anchors
PublicationThe inspection possibilities of ground anchors are limited to destructive test such as pull-out test. Guided wave propagation gives an opportunity to develop an inspection system dedicated to determine the condition of inspected element without violation of their integrity. In this paper the experimental study on wave propagation in laboratory models of ground anchors are presented. Experiments were conducted for different bonding...
-
The Optimal Location of Ground-Based GNSS Augmentation Transceivers
PublicationModern Global Navigation Satellite Systems (GNSS) allow for positioning with accuracies ranging from tens of meters to single millimeters depending on user requirements and available equipment. A major disadvantage of these systems is their unavailability or limited availability when the sky is obstructed. One solution is to use additional range measurements from ground-based nodes located in the vicinity of the receiver. The highest...
-
Experimental and numerical analysis of wave propagation in ground anchors
PublicationThe article focuses on wave propagation phenomenon in ground anchors. The main aim of the investigation is the non-destructive diagnostics and the assessment of the state of ground anchors, using the guided wave propagation method. Laboratory models of anchors with different lengths of the anchor body were tested and voltage signals of propagating waves were registered at several locations. For all tested specimens corresponding...
-
OIL-ASSISTED THERMO-MECHANICAL RECLAMATION OF GROUND TIRE RUBBER
PublicationNowadays, it is crucial to seek for the methods of by-products and waste utilization, considering both environmental and economic factors. The example of waste material generated in the massive amounts, which requires the attention is ground tire rubber generated during recycling of post-consumer car tires. It can be applied as a filler into different polymer matrices, but to enhance its effectivity proper modifications should...
-
Detection and time/frequency analysis of electric fields in the ground
PublicationThis paper sets out to detect and characterize electric fields in the ground (such as stray current fields) using a tandem time/frequency method of signal analysis. Results were obtained from investigations performed in the presence of a generated electric field with controlled variable characteristics, and in the presence of an electric field generated by a tramline. The analysis of measurement registers was performed using Short‐Time...
-
Reactive Processing and Functionalization of Ground Tire Rubber
PublicationThe dynamic development of the automotive industry resulted in a sig- nificant increase in rubber wastes, especially end-of-life tires, which are a serious threat to the natural environment and human health. This situation has enforced the industry and academic research groups to search new and cost-effective methods for recycling waste tires. In this field of research, reactive processing and functionaliza- tion seem to be a...
-
The Impact of Ground Tire Rubber Oxidation with H2O2 and KMnO4 on the Structure and Performance of Flexible Polyurethane/Ground Tire Rubber Composite Foams
PublicationThe use of waste tires is a very critical issue, considering their environmental and economic implications. One of the simplest and the least harmful methods is conversion of tires into ground tire rubber (GTR), which can be introduced into different polymer matrices as a filler. However, these applications often require proper modifications to provide compatibility with the polymer matrix. In this study, we examined the impact...
-
Compatibilization of polymeric composition filled with ground tire rubber – short review
PublicationWaste rubber is recognized as valuable materials resource and searching for new recycling methods is the main activity of many research institutions and companies. At the turn of the last years only few scientific papers about foamed polymer compositions filled with ground tire rubber were published. In paper review about progress in compatibilization and foaming of polymeric compositions filled with ground tire rubber.
-
GROUND WATER MONITORING AND REMEDIATION
Journals -
Autonomous, Ground Based, Self-Organizing Radiolocation Systems - AEGIR
PublicationThis article describes the construction and operation of autonomous ground-based radiolocation system that was developed as a technology demonstrator at the Technical University of Gdansk. Preliminary results and conclusions will be presented as well as analysis of its effectiveness. There will be also described the basic blocks of the system.
-
GROUND WATER
Journals -
Non-destructive inspection of ground anchors using guided wave propagation
PublicationThis paper deals with numerical and experimental investigations of specific problems of guided wave propagation in ground anchors. The research focuses on recognizing the phenomenon of the energy transfer between anchor components. Particular attention is paid to characteristic features of guided waves propagating in free and embedded parts of the tendon, at the interface between the tendon and the surrounding anchor body as well...
-
A novel heterogeneous model of concrete for numerical modelling of ground penetrating radar
PublicationThe ground penetrating radar (GPR) method has increasingly been applied in the non-destructive testing of reinforced concrete structures. The most common approach to the modelling of radar waves is to consider concrete as a homogeneous material. This paper proposes a novel, heterogeneous, numerical model of concrete for exhaustive interpretation of GPR data. An algorithm for determining the substitute values of the material constants...
-
Ground anchors diagnostic process based on elastic wave propagation method
PublicationThe paper is focused on analysis of elastic wave propagation in the context of diagnostics of ground anchors. Numerical simulations were performed to assess the possibility of evaluation of the anchorage quality. It was assumed that the quality and the load capacity of the anchor system directly depend on the length, on which mortar and steel cooperate.
-
The effect of different accelerators on the reclaiming efficiency of ground tire rubber
Open Research DataThe presented results concern the influence of different accelerators on the reclaiming efficiency of ground tire rubber (GTR). All the specimens were prepared using a two-roll mill and each sample was prepared in the same manner. Samples were submitted to curing analysis via Rheometer Monsanto 100S after 24 hours of aging. The attached data are related...
-
Effect of ground tire rubber on structural, mechanical and thermal properties of flexible polyurethane foams
PublicationFlexible polyurethane foams were modified with two kinds of ground tire rubber, untreated and thermo-mechanically reclaimed. A reclamation process was performed in auto-thermal conditions, which reduced the cost of the process and decreased the environmental impact of devulcanization (e.g., emission of gases). The reclamation process was carried out in a continuous manner using a co-rotating twin screw extruder. The foams were...
-
Rigid polyurethane foams modified with ground tire rubber - mechanical, morphological and thermal studies
PublicationRigid polyurethane foams, prepared by a single step method, were modified with the two types of ground tire rubber particles, i.e. untreated and thermo-mechanically reclaimed by using a co-rotating twin screw extruder. The foaming process as well as the structure and the physical, mechanical and thermal properties of the resulting foams were investigated. The presence of ground tire rubber decreased the velocity of polymerization....
-
The Influence of External Additional Loading on the Muscle Activity and Ground Reaction Forces during Gait
PublicationAsymmetrical external loading acting on the usculoskeletal system is generally considered unhealthy. Despite this knowledge, carrying loads in an asymmetrical manner like carrying on one shoulder, with one hand, or on the strap across the torso is a common practice. This study is aimed at presenting the effects of the mentioned load carrying methods on muscle activity assessed by using thermal field and ground reaction forces....
-
Preliminary Investigation on Auto-Thermal Extrusion of Ground Tire Rubber
PublicationGround tire rubber (GTR) was processed using an auto-thermal extrusion as a prerequisite to green reclaiming of waste rubbers. The reclaimed GTR underwent a series of tests: thermogravimetric analysis combined with Fourier-transform infrared spectroscopy (TGA-FTIR), scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR), and static headspace and gas chromatography-mass spectrometry (SHS-GC-MS) in order...
-
Novel microstrip low-pass filters with fractal defected ground structures
PublicationIn this study, three microstrip low-pass filters (LPFs) containing fractal-shaped defected ground structures have been designed and manufactured. To improve the performance of microstrip LPF, cascades of inductively coupled fractal resonators have been applied. Simultaneously, to achieve relatively constant microstrip impedance resulting in essentially low reflection losses, a modification of the strip geometry has been introduced....
-
Impact of thermal backfill parameters on current-carrying capacity of power cables installed in the ground
PublicationProper design of power installations with the participation of power cables buried in homogeneous and thermally well-conductive ground does not constitute a major problem. The situation changes when the ground is non-homogeneous and thermally low-conductive. In such a situation, a thermal backfill near the cables is commonly used. The optimization of thermal backfill parameters to achieve the highest possible current-carrying capacity...
-
Ground-based, Hyperbolic Radiolocation System with Spread Spectrum Signal - AEGIR
PublicationThe most popular radiolocation systems in the world (at present), is the American GPS (Global Positioning System). It is managed by the Department of Defense and there is always the possibility of the occasional inaccuracies or deliberate introduction of errors that prevent its use by the special services or armies of other countries than the U.S.A. This situation has spawned the need to develop an autonomous, ground-based radiolocation...
-
Characterization and properties of LDPE/(ground tire rubber)/crosslinked butyl rubber blends
PublicationIn recent years, interest in used rubber recycling, mainly focusing on the utilization of end-of-life tires, has heightened. This interest, is owing to the activities related to environmental protection and economic factors, which both stimulate companies to reuse the high-quality rubber present in ground rubber scrap. In this study, the application of crosslinked butyl rubber in thermoplastic compositions of low-density polyethylene...
-
Polyurethane/ground tire rubber composite foams based on polyglycerol: processing, mechanical and thermal properties
PublicationDuring the synthesis of rigid polyurethane foams, petrochemical polyol was substituted with polyglycerol, the product of thermo-catalytic polycondensation of waste glycerol, resulting from biodiesel production. Two types of ground tire rubbers, untreated and thermo-mechanically reclaimed, were used to obtain ‘‘green’’ polyurethane-polyglycerol composite foams. Samples were prepared by a single-step method for the ratio of NCO/OH...
-
International Journal of Geosynthetics and Ground Engineering
Journals -
Modification of Ground Tire Rubber—Promising Approach for Development of Green Composites
PublicationGround tire rubber (GTR) was mechano-chemically modified using a road bitumen 100/150 and two types of organic peroxides: di-(2-tert-butyl-peroxyisopropyl)-benzene (BIB) and dicumyl peroxide (DCP). The impact of used additives on reactive sintering efficiency and physico-mechanical properties of modified GTR was investigated using oscillating disc rheometer measurements, followed by tensile tests and swelling behavior studies....
-
Degradation of stiffness of building columns exposed to bending and impact load during ground motions
PublicationThe safety of civil engineering structures under external loads, including ground motions, is one of the issues related to the idea of sustainable society. The earthquake-induced soft-storey failure is a typical type of damage observed in buildings due to seismic excitation. The failure of an intermediate soft storey of a structure results in large vertical impact loading acting on the lower floors due to the fall of the upper...
-
Crack Detection in Metallic Surfaces Based on Dumbbell-Shaped Defected Ground Structures in Microstrip Technology
PublicationIn this paper, a novel crack detection sensor using a microstrip loaded with a Dumbbell-Shaped Defected Ground Structure (DS-DGS) is proposed. The sensing element is etched in the ground plane of a microstrip line and it is easy to fabricate. The electromagnetic (EM) field of the microstrip couples to the DS-DGS, thus demonstrating a bandstop behavior. It is shown that in the presence of a crack in a metallic surface underneath the...
-
Efficiency of thermomechanical reclaiming of ground tire rubber conducted in counter-rotating and co-rotating twin screw extruder
PublicationIn this article the results of research on a continuous thermomechanical reclaiming process of ground tire rubber (GTR) conducted in a twin screw extruder are presented. The effects of the rotation direction (co-rotating/counter-rotating), design of co-rotating plasticizing units and the rotational speed of the screws on the extruder working parameters, sol fraction and the degree of reclaiming in the obtained products were described....
-
Ground tire rubber functionalization as a promising approach for the production of sustainable adsorbents of environmental pollutants
PublicationWaste tires management and further utilization are currently one of the biggest concerns regarding the environment and human health protection. At present, shredding, grinding, or pulverization of waste tires are the most popular options for industrial recycling. Although many solutions for ground tire rubber (GTR) applications were checked and verified so far, their further implementation at an industrial scale is still very limited....
-
Numerical Analysis of a Steel Frame Building with Soft-storey Failure under Ground Motion Excitation
PublicationThe aim of this paper is to show the results of a numerical analysis focused on the behaviour of multi-storey steel frame building that suffers from a soft-storey failure under ground motion excitation. A numerical model of the structure was created in FEM computer software and was exposed to an impact that would have been generated after a soft-storey failure due to falling of the upper floors. During the analysis, the whole structure...
-
FINITE GROUND CPW-FED UWB ANTENNA OVER THE METALLIC CYLINDRICAL SURFACES
PublicationThe investigation of finite ground coplanar fed ultra-wideband (UWB) antenna and the influence of its curvature and the proximity of circular metallic screen on the reflection coefficients and radiation characteristics is presented. The antenna is composed of two circular coplanar strips which enclose slot aperture of similar shape and is designed on a thin and flexible substrate which allows its bending. The antenna configuration...
-
Ground-based radiolocation system - AEGIR
Publication -
In search of a common ground for the space sciences
PublicationThe paper discusses the relations between various aspects of human activities performed in space, taking into consideration the past, present and future contexts. Interdisciplinarity and integrity of technological issues combined with legal and management issues were emphasized. Consequently, it was recognized that it is necessary to build a network of universities, research-and-development companies and engineering companies....
-
Ground improvement with in situ Soil Mixing
PublicationOmówiono metodę wzmacniania słabego gruntu za pomocą technologii wgłębnego mieszania na sucho i mokro. W metodzie mokrej stosuje się składniki wiążące (głownie cementy) wymieszane z wodą, podawane w formie zaczynu. W metodzie suchej materiały wiążące podawane są w postaci sproszkowanej z udziałem sprężonego powietrza. Przedstawiono główne obszary zastosowania w geotechnice oraz podano przykłady kilku realizacji.
-
The method of detection of electromagnetic fields in ground
PublicationW prezentowanej metodzie, detekcja pola polega na pomiarach i analizie zmian rozkładu potencjału. Różnice potencjałów są mierzone jako napięcie pomiędzy elektrodami umieszczonymi w różnych pozycjach na powierzchni ziemi. Analiza tych napięć przy pomocy krótkoczasowej transformaty Fouriera STFT umożliwia wyznaczenie zmian spektralnej gęstości mocy sygnału w funkcji czasu. Ten rodzaj łącznej analizy czasowo-częstotliwościowej daje...
-
Investigation of volatile low molecular weight compounds formed during continuous reclaiming of ground tire rubber
PublicationGround tire rubber was thermo-mechanically reclaimed at different temperature conditions (80, 120, 160 °C) using a co-rotating twin screw extruder. The progress of ground tire rubber reclaiming was evaluated with specific mechanical energy, sol fraction and thermogravimetric analysis. Volatile organic compounds (VOCs) including volatile sulfur compounds (VCSs) released from ground tire rubber and ground tire rubber after reclaiming...
-
Comprehensive analysis of low-temperature methods for reclaiming of ground tire rubber
PublicationManagement of waste tires has become an important topic for decades. The lack of an effective method to manage the materials as mentioned above leads to illegal landfills. This problematic waste can be divided into two main categories depending on the physical condition of the waste: (i) partially used tires; (ii) end-of-life tires. While the first group can be reused or retreaded, the second group requires special measures to...
-
Improved selectivity compact band-stop filter with gosper fractal-shaped defected ground structures
PublicationA novel band-stop filter using Gosper fractal-shaped defected ground structures has been designed and manufactured. The improvement in the filter selectivity has been achieved by introducing a multiresonance fractal-shaped defect leading to a higher filter order, simultaneously maintaining its compact size. The experimental results prove the validity of proposed solution and its utility in novel miniaturized and severe requirement...
-
Development of methods improving storage stability of bitumen modified with ground tire rubber: A review
PublicationThe following paper presents an overview of methods for improving the storage stability at high temperature of rubber modified bitumen. The storage stability of the rubber modified bitumen can be improved by using a various types of modifiers that form the bonds between the components of these binders. The increase in stability can also be achieved by using crumbrubber surface-activated by furaldehyde or ground tire rubber (GTR)...
-
DETERMINATION OF THE HYDROXYL NUMBER OF GROUND TIRE RUBBER PARTICLES VIA MODIFIED TEST METHOD FOR ISOCYANATE GROUPS
PublicationNowadays, considering the environmental trends and law regulations associated with the circular economy, it is very important to seek for the methods of by-products and waste utilization. The example of such material, which requires the attention and recycling method is ground tire rubber generated during recycling of post-consumer car tires. It can be introduced into various polymer matrices as a filler, but to enhance its effectivity...
-
Use of response surface methodology in characterization of properties of recycled high density polyethylene/ground tire rubber compositions
PublicationSearching for newways to utilize rubber and polymerwaste has been the focus of many studies conducted by research centers and companies worldwide. In this study, the influence of extrusion conditions on the properties of thermoplastic compositions containing post-production recycled high density polyethylene (PE-HD) and ground tire rubber (GTR) at 50:50 mass ratiowas examined. Response Surface Methodology (RSM) was used to determine...
-
FTIR spectroscopic and thermogravimetric characterization of ground tyre rubber devulcanized by microwave treatment
PublicationIn this work, the phenomena involved in the microwave devulcanization of ground tyre rubber (GTR) were investigated. Three types of GTR with different content of organic compounds (elastomers, plasticizers, etc.), carbon black and ash have been studied. The chemical structure of GTR before and after a microwave devulcanization process was analyzed by Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA)...
-
Styrene-Butadiene Rubber/Modified Ground Tire Rubber Blends Co-Vulcanization: Effect of Accelerator Type
PublicationGround tire rubber was thermo-mechanically modified with using a co-rotating twin screw extruder. Modification of GTR was conducted in autothermal conditions. Styrene-butadiene rubber and modified ground tire rubber blends were prepared via two-roll milling. Obtained compounds were cured with conventional system (sulfur/vulcanization accelerator ratio was 2:1). During this research three commonly vulcanization accelerators (MBT,...
-
Processing, Performance Properties, and Storage Stability of Ground Tire Rubber Modified by Dicumyl Peroxide and Ethylene-Vinyl Acetate Copolymers
PublicationIn this paper, ground tire rubber was modified with dicumyl peroxide and a variable content (in the range of 0–15 phr) of ethylene-vinyl acetate copolymers characterized by different vinyl acetate contents (in the range of 18–39 wt.%). Modification of ground tire rubber was performed via an auto-thermal extrusion process in which heat was generated during internal shearing of the material inside the extruder barrel. The processing,...
-
Curing characteristics, mechanical and thermal properties of reclaimed ground tire rubber cured with various vulcanizing systems
PublicationGround tire rubber was thermo-mechanical reclaimed at 120 °C using a co-rotating twin screw extruder. The effect of vulcanizing system type on curing characteristics, static mechanical properties (tensile strength, elongation-at-break, hardness and resilience), dynamic mechanical properties and thermal properties of reclaimed ground tire rubber was investigated. Reclaimed rubber was cured using different types of vulcanization...
-
High frequency impulse ground penetrating radar application in assessment of interlayer connections
PublicationGround Penetrating Radar (GPR) technique is commonly used in the nondestructive evaluation of pavement structures. In particular, this method is used to estimate thicknesses of pavement layers as well as it can be utilized in advanced studies of pavement structures. The device presented in this paper comprise the high frequency impulse antennas that allow for investigating the interlayer zones in terms of their electromagnetic...
-
Ground Tire Rubber Filled Flexible Polyurethane Foam—Effect of Waste Rubber Treatment on Composite Performance
PublicationThe application range of flexible polyurethane (PU) foams is comprehensive because of their versatility and flexibility in adjusting structure and performance. In addition to the investigations associated with further broadening of their potential properties, researchers are looking for new raw materials, beneficially originated from renewable resources or recycling. A great example of such a material is ground tire rubber (GTR)—the...