Search
Search results for: MICROWAVE BAND- PASS FILTERS
-
Development of HFB with the Use of 2nd Order Pass-Band Filters
Publication -
Frequency-dependent coupling model for microwave band-pass filter
PublicationThe goal of this work was to create a circuit model which represents frequency-dependent coupling between microwave resonators. Our models are designed for in-line filters. The frequency-dependent coupling enables one to realize a transmission zero which is not possible in classical approach with frequency independent inverters. In addition, the proposed model allows us to observe out-of-band behavior, e.g. spurious resonance....
-
Interpolator wykorzystujący filtr z maskowaniem charakterystyki częstotliwościowej
PublicationInterpolator o dużej krotności wymaga stosowania dolnoprzepustowych filtrów cyfrowych o bardzo wąskim paśmie przejściowym. Przekłada się to na dużą złożoność obliczeniową i problemy z projektowaniem filtrów interpolacyjnych. W pracy zaproponowano użycie metody FRM rozbijającej filtr o wąskim paśmie przejściowym na grupę filtrów o obniżonych wymaganiach, co zmniejsza liczbę niezerowych współczynników. W rezultacie użycie tego rozwiązania...
-
Sample Rate Conversion Based on Frequency Response Masking Filter
PublicationThe sample rate conversion with high resampling ratios requires low-pass digital filters with very narrow transition band which results in high computational complexity and makes filter design problematic. Therefore in this work we propose to use the FRM method, which breaks the filter with a narrow transition band into a group of filters with reduced design requirements. These decreases the number of non-zero coefficients and...
-
Planar Microwave Bragg Reflector Resonant Dielectric Sensor
PublicationIn this paper, a periodic structure is used to design a microwave Bragg reflector with the help of hexagonal lattice, which provides a 5 GHz wide stopband between the low-pass band with cut-off frequency 2.6 GHz and the bandpass response with start and stop frequency 7.8 GHz and 10.5 GHz, respectively. A defect in lattice allows passing a narrowband signal at 6 GHz which is found, from the dispersion relation, to be in the region...
-
Design of a Patch Power Divider with Simple Structure and Ultra-Broadband Harmonics Suppression
PublicationThis paper introduces a simple H-shaped patch Wilkinson power divider (WPD), which provides ultra wide harmonics suppression band. The presented WPD designed at 1.8 GHz, and exhibits good performance at the operating bandwidth. In the proposed divider structure, two simple patch low-pass filters (LPFs) are employed at each branch, and three open ended stubs are added at each port. The proposed divider, implemented using the aforementioned...
-
Computationally-Efficient Statistical Design and Yield Optimization of Resonator-Based Notch Filters Using Feature-Based Surrogates
PublicationModern microwave devices are designed to fulfill stringent requirements pertaining to electrical performance, which requires, among others, a meticulous tuning of their geometry parameters. When moving up in frequency, physical dimensions of passive microwave circuits become smaller, making the system performance increasingly susceptible to manufacturing tolerances. In particular, inherent inaccuracy of fabrication processes affect...
-
Fast Design Optimization of Waveguide Filters Applying Shape Deformation Techniques
PublicationThis paper presents an efficient design of microwave filters by means of geometry optimization using shape deformation techniques. This design procedure allows for modelling complex 3D geometries which can be fabricated by additive manufacturing (AM). Shape deforming operations are based on radial basis function (RBF) interpolation and are integrated into an electromagnetic field simulator based on the 3D finiteelement method (FEM)....
-
Low-Voltage Low-Power Filters with Independent ω0 and Q Tuning for Electronic Cochlea Applications
PublicationAn acoustic second-order low-pass filter is proposed for filter banks emulating the operation of a human cochlea. By using a special filter structure and an innovative quality (Q)-factor tuning technique, an independent change of the cutoff frequency (ω0) and the Q-factor with unchanged gain at low frequencies is achieved in this filter. The techniques applied result in a simple filter design with low Q-factor sensitivity to component...
-
Kriging Models for Microwave Filters
PublicationSurrogate modeling of microwave filters’ response is discussed. In particular, kriging is used to model either the scattering parameters of the filter or the rational representation of the filter’s characteristics. Surrogate models for these two variants of kriging are validated in solving a microwave filter optimization problem. A clear advantage of surrogate models based on the rational representation over the models based on scattering...
-
Low-Cost Surrogate Models for Microwave Filters
PublicationA novel low-cost kriging-based multivariable parametric macromodeling technique for microwave filters is presented. Kriging is used to model both the residues and poles of a microwave filter's reflection coefficient, and the zeros of the transmission coefficient. The proposed residue-pole-zero (RPZ) technique is demonstrated to efficiently model a high dimensional (8D) microwave filter with pseudoelliptic characteristics.
-
Novel microstrip low-pass filters with fractal defected ground structures
PublicationIn this study, three microstrip low-pass filters (LPFs) containing fractal-shaped defected ground structures have been designed and manufactured. To improve the performance of microstrip LPF, cascades of inductively coupled fractal resonators have been applied. Simultaneously, to achieve relatively constant microstrip impedance resulting in essentially low reflection losses, a modification of the strip geometry has been introduced....
-
Low cost microwave X-band generator
PublicationA low cost microwave X-band generator for educational purposes was designed and built. Its simple construction and user's interface makes it suitable for a student laboratory.The generator is based on a single frequency conversion concept. It uses a digitally tunable PLL chip for intermediate frequency generation and an active frequency multiplier for frequency conversion. The generator covers 9,7 - 11 GHz part of the X frequency...
-
The time-varying low-frequency magnetic-field emitted from the ship’s inverter-fed induction motor
Open Research DataThe dataset contains the magnetic field measurement results that are part of a comprehensive study on the assessment of the magnetic field emissions onboard of the research-training vessel. The measurements were carried out, nearby the bow thruster motor fed from the inverter, during maneuvering and the sea voyage. The bow thruster is assembled in the...
-
Automatic Correction of Non-Anechoic Antenna Measurements using Low-Pass Filters
PublicationPrototype measurements belong to key steps in the development of antenna structures. They are normally performed in expensive facilities, such as anechoic chambers (ACs). Alternatively, antenna performance can be extracted (at a low cost) in non-anechoic conditions upon appropriate post-processing. Unfortunately, existing correction algorithms are difficult to set up and prone to failure, which limits their practical usefulness....
-
The Design of Cavity Resonators and Microwave Filters Applying Shape Deformation Techniques
PublicationThis article introduces shape deformation as a new approach to the computer-aided design (CAD) of high-frequency components. We show that geometry deformation opens up new design possibilities and offers additional degrees of freedom in the 3-D modeling of microwave structures. Such design flexibility is highly desirable if the full potential of additive manufacturing (AM) is to be exploited in the fabrication of RF and microwave...
-
Miniaturized Dual-Band SIW-Based Bandpass Filters Using Open-Loop Ring Resonators
PublicationThis article presents two novel architectures of dual-band substrate integrated waveguide (SIW) bandpass filters (BPFs). Initially, two identical open-loop ring resonators (OLRRs) are coupled face-to-face on the top of the SIW cavity to realize a dual-band single-pole BPF. To obtain two-pole dual-band characteristics, two OLRRs resonant units are assembled horizontally within the top metal layer of the SIW, which is a technique...
-
A Novel Synthesis Technique for Microwave Bandpass Filters with Frequency-Dependent Couplings
PublicationThis paper presents a novel synthesis technique for microwave bandpass filters with frequency-dependent couplings. The proposed method is based on the systematic extraction of a dispersive coupling coefficient using an optimization technique based on the zeros and poles of scattering parameters representing two coupled resonators.The application of this method of synthesis is illustrated using two examples involving four and five-pole...
-
The method of measuring the energy pass-band of a communication receiver
PublicationPrzedstawiono metodę wyznaczania energetycznego pasma odbiornika radiokomunikacyjnego na podstawie charakterystyki gęstości widmowej mocy szumów własnych na wyjściu odbiornika. Podano numeryczny estymator tego pasma. Wyprowadzono zależności na złożoną niepewność standardową wyznaczania szerokości pasma energetycznego odbiornika.
-
Fast Full-Wave Multilevel Zero-Pole Optimization of Microwave Filters
PublicationA new concept is proposed for the full-wave computer-aided design of microwave filters. The method consists of two stages and operates on the zeros and poles of the transfer function and their derivatives. These quantities are evaluated from the response computed by a full-wave electromagnetic solver with two levels of accuracy. The two stages make use of different models that are optimized using a low-accuracy electromagnetic...
-
Efficient Multi-Fidelity Design Optimization of Microwave Filters Using Adjoint Sensitivity
PublicationA simple and robust algorithm for computationally efficient design optimiza-tion of microwave filters is presented. Our approach exploits a trust-region (TR)-based algorithm that utilizes linear approximation of the filter response obtained using adjoint sensitivity. The algorithm is sequentially executed on a family of electromagnetic (EM)-simulated models of different fidelities, starting from a coarse-discretization one, and...
-
Sensitivity performance of all pole canonical low pass GmC filters.
PublicationW pracy badano własności częstotliwościowe kanonicznych filtrów dolnoprzepustowych GmC bez zer transmisyjnych. Przedstawiono ogólną strukturę kanonicznego filtru dolnoprzepustowego i jej opis macierzowy. Wyprowadzono ogólne wzory określające funkcje wrażliwościowe filtru. Dokonano porównania struktur do 10-go rzędu włącznie dla aproksymacji Butterwortha, Czebyshewa i Bessela.
-
Frequency-Variant Double-Zero Single-Pole Reactive Coupling Networks for Coupled-Resonator Microwave Bandpass Filters
PublicationIn this work, a family of frequency-variant reactive coupling (FVRC) networks is introduced and discussed as new building blocks for the synthesis of coupled-resonator bandpass filters with real or complex transmission zeros (TZs). The FVRC is a type of nonideal frequency-dependent inverter that has nonzero elements on the diagonal of the impedance matrix, along with a nonlinear frequency-variation profile of its transimpedance...
-
Dimensional Synthesis of Coupled-Resonator Pseudoelliptic Microwave Bandpass Filters with Constant and Dispersive Couplings
PublicationIn this paper, we propose a novel technique for the dimensional synthesis of coupled-resonator pseudoelliptic microwave filters with constant and dispersive couplings. The proposed technique is based on numerical simulations of small structures, involving up to two adjacent resonators, and it accounts for a loading effect from other resonators by replacing them with terminations coupled through appropriately scaled inverters. The...
-
General Gm-C filters with finite band transconductors.
PublicationW pracy przedstawiono wyniki badań dotyczących wpływu skończonego pasma przenoszonych częstotliwości elementów transkonduktancyjnych na właściwości filtrów Gm-C czasu ciągłego. Opracowano miary dewiacji charakterystyk częstotliwościowych filtrów Gm-C spowodowanych skończonymi wartościami elementów pojemnościowych i rezystancyjnych na wyjściu transkonduktorów. Proponowana procedura analizy może znaleźć szerokie zastosowanie...
-
Rapid simulation-driven design of miniaturised dual-band microwave couplers by means of adaptive response scaling
PublicationOne of the major challenges in the design of compact microwave structures is the necessity of simultaneous handling of several objectives and the fact that expensive electromagnetic (EM) analysis is required for their reliable evaluation. Design of multi-band circuits where performance requirements are to be satisfied for several frequencies at the same time is even more difficult. In this work, a computationally efficient design...
-
Inline Microwave Filters With N+1 Transmission Zeros Generated by Frequency-Variant Couplings: Coupling-Matrix-Based Synthesis and Design
PublicationA general coupling-matrix-based synthesis methodology for inline Nth-order microwave bandpass filters (BPFs) with frequency-variant reactive-type couplings that generate N+1 transmission zeros (TZs) is presented in this brief. The proposed approach exploits the formulation of the synthesis problem as three inverse nonlinear eigenvalue problems (INEVPs) so that the coupling matrix is built from their sets of eigenvalues. For this...
-
Design of mm-wave MIC frequency multiplayers and mixers using simple microstrip high-pass filters
PublicationPrzedyskutowano podstawowe wymagania dotyczące impedancji elementów półprzewodnikowych wykorzystywanych w mieszaczach i powielaczach częstotliwości projektowanych dla zakresu fal milimetrowych. Określono typy układów filtrujących niezbędnych w różnych częściach układów, podkreślając znaczenie filtrów górnoprzepustowych. Mikropaskowy filtr ze zwartym brzegiem został wykonany i zaimplementowany w mieszaczu pracującym w zakresie 20-40GHz.
-
Low order autoregressive (AR) models for FDTD analysis of microwave filters.
PublicationArtykuł opisuje zastosowanie modeli AR w celu poprawy efektywności analizy struktur filtrujących metodą różnic skończonych w dziedzinie czasu (FD-TD). Opisanych jest szereg kryteriów pozwalających na automatyczne tworzenie modeli AR sygnałów czasowych, w tym wybór fragmentu odpowiedzi układu stanowiący podstawę ekstrakcji współczynników modelu, współczynnika decymacji oraz rzędu modelu. Skuteczność wprowadzonych kryteriów...
-
Expedited Re-Design of Multi-Band Passive Microwave Circuits Using Orthogonal Scaling Directions and Gradient-Based Tuning
PublicationGeometry scaling of microwave circuits is an essential but challenging task. In particular, the employment of a given passive structure in a different application area often requires re-adjustment of the operating frequencies/bands while maintaining top performance. Achieving this necessitates utilization of numerical optimization methods. Nonetheless, if the intended frequencies are distant from the ones at the starting point,...
-
Bandwidth-Controllable Third-Order Band Pass Filter Using Substrate Integrated Full- and Semi-Circular Cavities
PublicationThe article presents a novel circular substrate integrated waveguide (SIW) bandpass filter (BPF) with controllable bandwidth. The proposed BPF is configured using two microstrip feedlines, semi- circular SIW cavities, capacitive slots, and inductive vias. The circular cavity is bisected into two halves, with the two copies thereof being cascaded. Two bisected and cascaded structures obtained this way are subsequently connected...
-
A Microwave Sensor with Operating Band Selection to Detect Rotation and Proximity in the Rapid Prototyping Industry
PublicationThis paper presents a novel sensor for detecting and measuring angular rotation and proximity, intended for rapid prototyping machines. The sensor is based on a complementary split-ring resonator (CSRR) driven by a conductor-backed coplanar waveguide. The sensor has a planar topology, which makes it simple and cost-effective to produce and accurate in measuring both physical quantities. The sensor has two components, a rotor, and...
-
A Novel Coupling Matrix Synthesis Technique for Generalized Chebyshev Filters With Resonant Source–Load Connection
PublicationThis paper reports a novel synthesis method for microwave bandpass filters with resonant source–load connection. In effect, a network realizing N+1 transmission zeros (where N is the number of reflection zeros) is obtained. The method is based on a prototype transversal coupling matrix (N+2, N+2) with source and load connected by a resonant circuit formed by a capacitor in parallel with a frequency-invariant susceptance. To complement...
-
Synthesis of coupled lossy resonator filters.
PublicationA technique for fast synthesis of coupling matrix low-pass prototypes of generalized. Chebyshev bandpass filters with lossy resonators is presented in this letter. The coupling matrix is found by solving a nonlinear least squares problem based on zeros and poles of filter's transfer functions.
-
On the synthesis of coupled-lossy resonator filters with unloaded quality factor control
PublicationA technique for fast synthesis of coupling matrix low-pass prototypes of generalized Chebyshev bandpass filters with lossy resonators is presented in this paper. The coupling matrix is found by solving a nonlinear least squares problem based on zeros and poles of filter's transfer functions. Additional constraints are introduced that allow one to control the level of unloaded quality factor of resonators.
-
Two-Rate Based Low-Complexity Variable Fractional-Delay FIR Filter Structures
PublicationThis paper considers two-rate based structures for variable fractional-delay (VFD) finite-length impulse response (FIR) filters. They are single-rate structures but derived through a two-rate approach. The basic structure considered hitherto utilizes a regular half-band (HB) linear-phase filter and the Farrow structure with linear-phase subfilters. Especially for wide-band specifications, this structure is computationally efficient...
-
Anomalous anisotropy of deuterium-grown boron-doped diamond and the role of boron-tetramers in the Mott-Insulator transition
Open Research DataWe show anisotropy in the superconductivity for boron-doped diamond thin films prepared with Microwave Plasma Assisted Chemical Vapor Deposition using deuterium-rich plasma. This anomalous phase transition is linked with the emergence of boson quantum entanglement states behaving as a bosonic insulating state. Here, we show that the superconducting...
-
Results and models for Novel high frequency components with non-conventional shape employing smooth geometry deformation of 3D solid with FFD
Open Research DataThe project aims to investigate the possibility of developing and manufacturing novel high frequency devices having non-standard geometries, allowing for improved electromagnetic performance over what is achievable with currently available design tools. The non-conventional geometry will be obtained by employing the free-form shape deformation technique...
-
FIR Filter Design Using Distributed Maximal Flatness Method
PublicationIn the paper a novel method for filter design based on the distributed maximal flatness method is presented. The proposed approach is based on the method used to design the most common FIR fractional delay filter - the maximally flat filter. The MF filter demonstrates excellent performance but only in a relatively narrow frequency range around zero frequency but its magnitude response is no greater than one. This ,,passiveness”...
-
Sidrish Zahra
PeopleSidrish Zahra received her B.Sc. degree in Electrical (Telecommunication) Engineering from school of Electrical Engineering, Government College University Faisalabad (GCUF), Pakistan in 2016.Then, she received the M.S. degree in School of Information and Communication Engineering, University of Electronic Science & Technology of China (UESTC) in 2019. Now, She is pursuing her Ph.D. degree in Control, Electrical and Electronics...
-
Depth Images Filtering In Distributed Streaming
PublicationIn this paper, we propose a distributed system for point cloud processing and transferring them via computer network regarding to effectiveness-related requirements. We discuss the comparison of point cloud filters focusing on their usage for streaming optimization. For the filtering step of the stream pipeline processing we evaluate four filters: Voxel Grid, Radial Outliner Remover, Statistical Outlier Removal and Pass Through....
-
Automated Design of Linear Phase Filters
PublicationThis paper presents a fast technique for an automated design of microwave filters with linear phase. The proposed method exploits the cost function defined using the location of complex zeros and poles of the filter’s transfer and reflection function. The effectiveness of the proposed technique is presented with two illustrative examples.
-
Ladder-Based Synthesis and Design of Low-Frequency Buffer-Based CMOS Filters
PublicationBuffer-based CMOS filters are maximally simplified circuits containing as few transistors as possible. Their applications, among others, include nano to micro watt biomedical sensors that process physiological signals of frequencies from 0.01 Hz to about 3 kHz. The order of a buffer-based filter is not greater than two. Hence, to obtain higher-order filters, a cascade of second-order filters is constructed. In this paper, a more...
-
Technique to improve CMRR at high frequencies in CMOS OTA-C filters
PublicationIn this paper a technique to improve the common-mode rejection ratio (CMRR) at high frequencies in the OTA-C filters is proposed. The technique is applicable to most OTA-C filters using CMOS operational transconductance amplifiers (OTA) based on differential pairs. The presented analysis shows that a significant broadening of CMRR bandwidth can be achieved by using a differential pair with the bodies of transistors connected to...
-
DEPTH IMAGES FILTERING IN DISTRIBUTED STREAMING
PublicationIn this paper we discuss the comparison of point cloud filters focusing on their applicability for streaming optimization. For the filtering stage within a stream pipeline processing we evaluate three filters: Voxel Grid, Pass Through and Statistical Outlier Removal. For the filters we perform series of the tests aiming at evaluation of changes of point cloud size and transmitting frequency (various fps ratio). We propose a distributed...
-
Substrate-integrated waveguide (SIW) filter design using space mapping
PublicationIn this paper, we present a fast technique for an automated design of microwave filters in substrate integrated wave (SIW) technology. The proposed methodology combines the space mapping technique with a cost function defined using the location of complex zeros and poles of filter’s transfer and reflection function and uses a rectangular waveguide as a surrogate model. The effectiveness of the proposed technique is presented with...
-
Miniaturized bandpass substrate integrated waveguide filter with frequency-dependent coupling realized using asymmetric GCPW discontinuity
PublicationAn asymmetric GCPW discontinuity is proposed to provide frequency-dependent coupling in microwave bandpass filters. Wider and narrow sections introduce, respectively, the capacitive and inductive component to the equivalent circuit representing coupling. By selecting the dimensions of the discontinuity and width of the inductive window in substrate integrated waveguide, an additional transmission zero can be introduced at prescribed...
-
A Subspace-Splitting Moment-Matching Model-Order Reduction Technique for Fast Wideband FEM Simulations of Microwave Structures
PublicationThis article describes a novel model-order reduction (MOR) approach for efficient wide frequency band finite-element method (FEM) simulations of microwave components. It relies on the splitting of the system transfer function into two components: a singular one that accounts for the in-band system poles and a regular part that has no in-band poles. In order to perform this splitting during the reduction process, the projection...
-
Novel topology of compact coplanar waveguide resonant cell low-pass filter
PublicationIn this study, a novel pseudoelliptic function low-pass filter (LPF) constituted by a compact coplanar waveguide resonant cell has been designed and manufactured. The lumped-element seven-pole prototype has been adequately realized by using complementary perturbations located both in signal line and ground plane metallization. The fabricated uniplanar LPF offers a compact size of 5.6 x 9.8 mm2, return loss better than 26 dB over...
-
Automated microwave planar filter design with generalized Chebyshev characteristics.
PublicationIn this paper a technique of automatization of design of microwave filters with generalized Chebyshev characteristics is presented. A full wave electromagnetic simulator linked with the Matlab computing environment is used to ensure a rigorous numerical analysis while at the same time allowing automatization. To decrease time of optimization and overall design process, the Cauchy interpolation technique was used. An automated design...