Search
displaying 1000 best results Help
Search results for: POROELASTIC ROAD SURFACE
-
Tyre/road noise reduction by a poroelastic road surface
PublicationLow noise road surfaces of existing types may in favourable cases and in new conditions provide up to 7 dB of noise reduction. For higher noise reductions, innovative solutions must be sought. Poroelastic road surfaces (PERS) may be such a solution, which currently is studied in the EU project PERSUADE. This paper presents results of trials with a PERS version prefabricated by one of the project partners. Tests were made in a laboratory...
-
Poroelastic Road Surface – a Promising Road Traffic Noise Abatement Solution
PublicationRoad surfaces have a direct impact on the generation of noise by rolling tyres, the main and dominant source of noise of moving vehicles, as well as may affect propagation of noise emitted by all noise sources of a vehicle. Thus there is no doubt that pavement should be considered as one of the major potential road traffic noise abatement measure. Low noise pavements of existing types may in new conditions provide up to 8 dB of...
-
Tyre/road noise reduction of poroelastic road surface tested in a laboratory
PublicationA so-called poroelastic road surface (PERS) is being developed in Europe. This contains a large percentage of rubber particles mixed with hard aggregate (stone and sand) and bound with polyurethane. This gives high air void content (around 30 %), high elasticity and smooth texture, all of which should give low noise properties. Inthis experiment anominally 30 mm thick sample of PERS was mounted on a steel drum. Various car tyres...
-
Poroelastic Road Surfaces - State of The Art
PublicationPoroelastic Road Surfaces (PERS) constitute a specific group of pavements containing a great amount of crumbled rubber. In most cases rubber aggregate constitutes about 20% of the mixture (by weight) and a polyurethane resin is used as a binder. As a result, PERS is characterized by a much higher elasticity than asphalt and a high porosity typical for drainage pavements. Due to this, tire/road noise is greatly reduced and on top...
-
Temperature influence on tyre/road noise on poroelastic road surface based on laboratory measurements
PublicationThe temperature effect on measured tyre/road noise is very important phenomena as it may lead to significant errors in measurement results due to substantial influence of this parameter on the obtained values. It depends mainly on the particular tyre-road combination. It is different for dense and porous as well as for bituminous and cement concrete pavements. It differs also depending on tested tyre. The correction procedure for...
-
Further development of the poroelastic road surface within the new Polish project SEPOR
PublicationRoad surfaces have a direct impact on noise generated by rolling tyres, the main and dominant source of noise of moving vehicles. Road surface texture, porosity and stiffness/elasticity govern the pavement contribution to tyre/road noise the most. An experimental PoroElastic Road Surface (PERS) is a wearing course with a high content of interconnected voids (pores) and with an elastic behavior due to the use of small particles...
-
Ultra Low Noise Poroelastic Road Surfaces
PublicationNoise is one of the most important environmental problems related to road traffic. During the last decades, the noise emitted by the engines and powertrains of vehicles was greatly reduced and tires became a clearly dominant noise source. The article describes the concept of low noise poroelastic road surfaces that are composed of mineral and rubber aggregate bound by polyurethane resin. Those surfaces have a porous structure and...
-
Biological hazards in low noise, poroelastic road surfaces
PublicationDrainage pavements as well as poroelastic pavements ("PERS") are a very efficient way to decrease traffic noise by reducing tire/road noise at the source as well as noise propagation over the road surface. Many noise generating mechanisms at the tire/road interface are very much reduced by road porosity (pipe resonance, "air pumping", Helmholtz resonance and the horn effect). A well-designed porous or poroelastic road surface may...
-
Tire/Road Noise On Poroelastic Road Surfaces - Results Of Laboratory Measurements
PublicationTire/road noise is the most important part of traffic noise for medium and high speed driving both in the case of passenger cars and trucks. The potential to make modification of tires that significantly reduce tire/road noise in nearly over, at least for conventional tires so the only promising action is to improve road pavements. One of the innovative solutions is poroelastic road pavement (PERS) that reduces airflow related...
-
Risks related to car fire on innovative Poroelastic Road Surfaces-PERS
PublicationTo reduce tyre/road noise, the concept of poroelastic road surfaces (PERS) was invented. PERS is a road surface material that is porous, and at the same time, it is flexible because of the substantial amount of rubber granulate content (from 20% to 85%). The rubber and stone particles are bound by polyurethane resin instead of bitumen. It was feared that in case of fire, because of the high content of rubber and polyurethane, there...
-
Poroelastic Low Noise Road Surfaces
PublicationNoise is one of the most important problems related to road traffic. During the last decades, noise emitted by engine and powertrain of vehicles was greatly reduced and tyres became a clearly dominant noise source. The paper describes the concept of low noise poroelastic road surfaces that are composed with mineral and rubber aggregate bound by polyurethane resin. Those surfaces have a porous structure and are much more flexible...
-
Low Noise Poroelastic Road Pavements Based On Bituminous Binder
PublicationTire/road noise is the dominant source of traffic noise. It depends both on the tire design and on the characteristics of road pavements as well as on the vehicles’ operating conditions. Due to the fact that conventional (pneumatic) car tires have almost reached the limits of their ability to further reduce their noisiness, it is widely believed that the additional reduction of tire noise will be possible mainly through modifications...
-
Low noise poroelastic road pavements based on modified asphalt binder
PublicationTire/road noise is one of the most important environmental problems related to road traffic. As the most effective way to fight noise is reduction of sound emission from the source, a lot of work is being done to improve tire and road surfaces construction. This paper describes the first “road” results obtained within the SEPOR project, which is focused on developing a low noise poroelastic road surface based on bituminous binder....
-
Assessing the Effects of the Road Surface and Weather Conditions on Road Safety
PublicationWhen transport is analysed for its safe delivery the focus is mainly on assessing the safety of roads and the risk of undesired events. These include road accidents, an occurrence which is relatively rare and random. Randomness means that accidents depend on several factors which are partly deterministic (can be controlled) and partly stochastic (random and unpredictable). The set of crash contributing factors can be classified...
-
PERS - QUIET ROAD SURFACE FOR URBAN AREAS
PublicationTraffic noise is one of the most important environmental problems in densely populated urban areas. At low speeds the tyre/road interaction dominates all other sources. It is anticipated that when electric and hybrid vehicles gain dominance in city traffic, the importance of tyre/road noise will still increase as electric engines are much less noisy than combustion engines. On the other hand, electric and hybrid urban vehicles...
-
Economical methods for measuring road surface roughness
PublicationTwo low-cost methods of estimating the road surface condition are presented in the paper, the first one based on the use of accelerometers and the other on the analysis of images acquired from cameras installed in a vehicle. In the first method, miniature positioning and accelerometer sensors are used for evaluation of the road surface roughness. The device designed for installation in vehicles is composed of a GPS receiver and...
-
The influence of road surface unevenness on tyre rolling resistance
PublicationThe geometric characteristics of road surface substantially affect the interaction between tyre and road. Depending on pavement texture wavelength, the texture chiefly affects tyre/road friction, rolling resistance, interior and exterior noise, tyre wear, and ride comfort. The article presents results of investigations on the influence of road surface unevenness on the rolling resistance of passenger car and truck tyres. The tests...
-
Detection of Water on Road Surface with Acoustic Vector Sensor
PublicationThis paper presents a new approach to detecting the presence of water on a road surface, employing an acoustic vector sensor. The proposed method is based on sound intensity analysis in the frequency domain. Acoustic events, representing road vehicles, are detected in the sound intensity signals. The direction of the incoming sound is calculated for the individual spectral components of the intensity signal, and the components...
-
TIRE/ROAD NOISE AND TIRE ROLLING RESISTANCE ON PROTOTYPE PERS SURFACE
PublicationPoroelastic road surfaces are characterized by low noise of tires running on them.Road pavements of this type are promising solution to problems related to traffic noise in cities and on rural roads. Some technical problems still have to be solved, in particular regarding durability and skid resistance on wet surface. Ongoing and planned works are to contribute to create a quiet, durable and safe road surface, which will become...
-
Impact of the surface evenness and texture on tire/road rolling resistance
PublicationThis paper deals with the issue of a surface's roughness and texture impact on tire/road rolling resistance. It includes a brief description of research aims, measurements and an analysis of results. It also presents observations and conclusions regarding drum facility modernisation which allows studies concerning surface's roughness and texture impact on tire/road rolling resistance.
-
Road surface roughness estimation employing integrated position and acceleration sensor
PublicationAssessment of a surface quality being an essential task for the authorities supervising the roads provides the subject of the paper. Information about riding quality of a pavement, important for drivers, both in terms of their comfort and safety is collected during experiments employing mobile sensors. The paper describes the use of a miniature position and acceleration sensor for evaluation of the roughness of the road surface....
-
The impact of the Tri-City Ring Road on surface water of small endorheic wetlands
PublicationThe paper presents the results of the impact of the Tri-City Ring Road on small endorheic catchment basins. Particular attention was paid to pollution discharged from the road to the surface water, as well as changes in hydrological conditions in the vicinity of the road. In the study, surface water samples were analysed in terms of their electrolytic conductivity, pH and content of major minerals. GIS was also used to study transformation...
-
Network design for surface water quality monitoring in a road construction project using Gamma Test theory
PublicationRoad construction has a negative environmental impact on the surrounding aquatic environment, requiring the continuous monitoring of surface water quality. Here, optimization of the water quality monitoring network (WQMN) is an essential step in supporting the sustainable development of road construction projects. This study introduces Gamma Test theory (GTT) as a practical method for optimizing the WQMN of surface waters during...
-
Exploring the Relationship between Particulate Matter Emission and the Construction Material of Road Surface: Case Study of Highways and Motorways in Poland
Publication -
Wpływ obwodnicy Trójmiasta na chemizm wód powierzchniowych niewielkich zagłębień bezodpływowych = The impact of the Gdańsk's ring road on the chemical composition of the surface waters in small outflowless pools
PublicationPrzedstawiono wyniki badań wpływu Obwodnicy Trójmiasta na chemizm wód niewielkich zbiorników bezodpływowych. Próbki poddano analizie na zawartość wybranych kationów i anionów oraz zbadano takie parametry jak pH oraz przewodnictwo. Uzyskane wyniki bardzo jasno wskazują na wysoki wpływ obwodnicy na skład i rodzaj zanieczyszczeń obecnych w badanych próbkach. Zaobserwowano m.in. alkalizację badanych wód oraz wysoki poziom stężeń takich...
-
Tyre/road noise of passenger car tyres, including tyres for electric vehicles - road measurements
PublicationThe paper presents the results from CPX measurements of tyre/road noise performed for selected passenger car tyres, including the tyres especially designed for electric vehicles. The tyres have been measured when rolling on several typical road surfaces in Norway and in Poland. In addition, the tyres have been measured on some very low noise road surfaces, such as a the poroelastic road surface (PERS). The measurement results...
-
Comparison of road and laboratory measurements of tyre/road noise
PublicationTyre/road noise is one of the major environmental problems related to road traffic. There are several measuring methods of tyre/road noise that may be carried out on the road (for example Coast-down and Close Proximity Method) or in the laboratory (Drum Method). Road measurements are preferred for evaluations of pavement properties while laboratory methods are mostly used to evaluate tyres. One of the biggest problems associated...
-
Initial Field Validation of Poroelastic Pavement Made with Crumb Rubber, Mineral Aggregate and Highly Polymer-Modified Bitumen
PublicationTire/road noise in most driving conditions dominates other sources of traffic noise. One of the most efficient ways of reducing tire/road noise is to use the so-called “low noise pavement”. According to numerous studies, at present, poroelastic road pavement that is composed of rubber and mineral aggregate and polyurethane or bituminous binder gives the best noise reduction up to 12 dB. Unfortunately, there are many problems with...
-
Dawid Ryś dr hab. inż.
PeopleCourses PRINCE2® Foundation Certificate in Project Management Tire-Pavement Interaction course Micromechanical Analysis of Asphalt Concrete
-
The Use of Direct Shear Test for Optimization of Interlayer Bonding Under a Poroelastic Layer
PublicationPoroelastic Road Surfaces (PERS) are characterised by porous structure with air void content of 20% or higher and stiffness almost 10 times lower than that of a standard asphalt course. Such properties enable noise reduction by up to 12 dB in comparison to SMA 11 mixture. However, the disadvantage of a poroelastic pavement is its low durability, which partially results from delamination from the lower layer. The paper aims to investigate...
-
Potential reduction of traffic noise by the means of increased fleet of electric vehicles using a combination of low-noise tyres and low-noise road surfaces
PublicationIn the future, the number of zero-emission vehicles like electric and plug-in hybrid vehicles (in electric mode) is expected to be a substantial part of the vehicle fleet. In Norway, such vehicles already account for approximately 20 % of all new cars sold. Since these vehicles emit negligible noise related to the power-train, the tyre/road noise is the dominating noise source. In the LEO project, tyres designed for such cars have...
-
Design of poroelastic wearing course with the use of direct shear test
PublicationPoroelastic Road Surfaces (PERS) are characterized by porous structure with at least 20% of air void content and stiffness almost 10 times lower than typical asphalt course. Such properties enable noise reduction up to 12 dB in comparison to SMA 11 mixture. However, the main disadvantage of previously used poroelastic mixtures, based on resin type binders, was their low durability, which resulted in raveling and delamination from...
-
The innovative approach for using pavement as a fire prevention measure in tunnels
PublicationThe paper consists of two main parts: first presents study regarding the typically used pavement structures in tunnels and the second part: the first fire trials of the poroelastic SEPOR (Safe, Eco-friendly POroelastic Road Surface) mixture which was designed to be used among other uses in tunnels. In the first part of the paper different pavement materials, such as cement concrete, asphalt concrete, stone mastic asphalt and porous...
-
Investigation of Acoustic Properties of Poroelastic Asphalt Mixtures in Laboratory and Field Conditions
PublicationMeasures for the improvement of acoustic conditions in the vicinity of roads include the construction of pavement structures with low-noise surfaces with optimal macrotexture and the highest possible sound absorption coefficient. Laboratory evaluation of acoustic properties of a designed asphalt mixture before its placement in the pavement is a good solution. Currently, the most popular method for the determination of the sound...
-
Analiza stanu nawierzchni i klas pojazdów na podstawie parametrów ekstrahowanych z sygnału fonicznego
PublicationCelem badań jest poszukiwanie parametrów wektora cech ekstrahowanego z sygnału fonicznego w kontekście automatycznego rozpoznawania stanu nawierzchni jezdni oraz typu pojazdów. W pierwszej kolejności przedstawiono wpływ warunków pogodowych na charakterystykę widmową sygnału fonicznego rejestrowanego przy przejeżdżających pojazdach. Następnie, dokonano parametryzacji sygnału fonicznego oraz przeprowadzano analizę korelacyjną w celu...
-
Badanie stanu nawierzchni drogowej z wykorzystaniem uczenia maszynowego
PublicationW artykule opisano budowę systemu informowania o stanie nawierzchni drogowej z wykorzystaniem metod cyfrowego przetwarzania obrazów oraz uczenia maszynowego. Efektem wykonanych prac badawczych jest eksperymentalna platforma, pozwalająca na rejestrację uszkodzeń na drogach, system do analizy, przetwarzania i klasyfikacji danych oraz webowa aplikacja użytkownika do przeglądu stanu nawierzchni w wybranej lokalizacji.
-
Analiza ruchu drogowego z wykorzystaniem analizy akustycznej
PublicationTematyka pracy porusza zagadnienia dotyczące pozyskiwania informacji o ruchu drogowym z wykorzystaniem monitoringu akustycznego. Przybliżono podstawowe techniki nadzoru nad ruchem drogowym. Przedstawiono założenia akustycznego detektora ruchu i zbadano jego skuteczność na trzech płaszczyznach działania – zliczania pojazdów, klasyfikacji rodzajowej i klasyfikacji warunków pogodowych panujących na nawierzchni
-
Akustyczna analiza natężenia ruchu drogowego dla systemów zarządzania ruchem
PublicationW pracy przybliżono wybrane zagadnienia z dziedziny zarządzania transportem drogowym w Polsce i na świecie. W tym kontekście pzredstawiono potrzeby rynkowe, wymagania jak i możliwości w zakresie pozyskiwania informacji o aktualnym stanie sieci drogowych. Zaproponowano akustyczną metodę nadzorowania ruchu drogowego i jej możliwości w kontekście systemów zarządzania ruchem. Przedstawiono schemat akwizycji sygnału wraz z danymi odniesienia....
-
APPLIED SURFACE SCIENCE
Journals -
Marek Pszczoła dr hab. inż.
PeopleI am a Faculty member (Department of Highway and Transportation Engineering) at the Faculty of Civil and Environmental Engineering, Gdansk University of Technology, Poland). My main research interests include: low-temperature properties of asphalt mixtures, low temperature cracking assessment of pavement structures, road materials properties, thermal stress analysis, design of pavement structures, airfield design and analysis....
-
Optimisation and field assessment of poroelastic wearing course bond quality
PublicationCompared to typical asphalt mixtures, poroelastic mixtures are characterised by high porosity and high flexibility, which are desirable for traffic noise reduction. However, the same properties increase the risk of debonding from the lower layer, which is a significant source of premature damage. The study investigates which of the factors – tack coat agent, type and texture of the lower layer – have the greatest impact on interlayer...
-
Bitumen-Based Poroelastic Pavements: Successful Improvements and Remaining Issues
PublicationThis article presents the development process of designing and testing poroelastic pavement based on highly polymer-modified bitumen. Poroelastic wearing course was composed of mineral and rubber aggregate mixed with highly polymer-modified bitumen, in contrast to previous trials, during which polyurethane resins were mainly used as binder, which led to several serious technological problems concerning difficult production, insufficient...
-
Road Materials and Pavement Design
Journals -
Surface Science - 2021/2022
e-Learning CoursesThe goal of the subject is the presentation of basic problems resulting from he existence of interfacebetween material objects and its surroundings. Discussion of the consequences arising from the existenceof surface energy. Analysis of possible applications of surface phenomena in technology. Understanding ofproblems and benefits resulting from decreasing dimensions of objects with the special emphasis on thesemiconductor band...
-
Surface Science - 2023/2024
e-Learning CoursesThe course is not a full time lecture but on the consultation/handouts. The consulations are held every two weeks. The course is based on the Springer textbook: Surface Science An Introduction Downloadable at: https://link.springer.com/book/10.1007/978-3-662-05179-5 (PG network or vpn access) The goal of the subject is the presentation of basic problems resulting from he existence of interfacebetween material objects...
-
Road texture influence on tyre rolling resistance
PublicationTyre performance, one of the critical factors for vehicle users, is strongly related to theroad surface characteristics, most notably to the pavement texture. Phenomena that occur at the tyre/road interface affect tyre friction (skid resistance), rolling resistance, tyre wear and tyre/road noise. This article deals with relationship between surface texture and rolling resistance of light and heavy vehicle tyres. Mean profile depth...
-
Poroelastic Material for Urban Roads Wearing Courses
PublicationConventional road materials used for producing wearing courses of roads are based on mineral aggregate and bituminous or Portland cement binders. The road materials must be optimized for different properties, including skid resistance, durability, rolling resistance and tire/road noise. Unfortunately, it seems that within classic technologies it is very difficult to achieve further reduction of tire/road noise. Innovative porous...
-
Poroelastic Material for Urban Roads Wearing Courses
PublicationConventional road materials used for producing wearing courses of roads are based on mineral aggregate and bituminous or Portland cement binders. The road materials must be optimized for different properties, including skid resistance, durability, rolling resistance and tire/road noise. Unfortunately, it seems that within classic technologies it is very difficult to achieve further reduction of tire/road noise. Innovative porous...
-
Długie pociągi
PublicationWskazano, że przy wprowadzaniu długich pociągów pojawiają się możliwości, ale i ograniczenia różnej natury oraz problemy do rozwiązania. Inne w przypadku długich pociągów i inne w przypadku ciężkich pociągów. Pokazano długie pociągi, jako szansę na polepszenie bezpieczeństwa na drogach, poprzez ograniczenie na nich ruchu samochodów ciężarowych. Łatwiej będzie w praktyce realizować pomysł „Tiry na tory” Długie pociągi są szansą...
-
Urban and Road Engineering - Smolnicki
e-Learning CoursesLectures about "Urban and Road Engineering", dedicated to sixth semester of the English-speaking group, will be conducted in a way that activates students. Lectures on Road Engineering cover a wide range of important issues related to the subject, starting from a discussion of the historical circumstances of the creation, development and domination of the contemporary conventional model, through identifying new approaches and...
-
Effect of the Road Environment on Road Safety in Poland
PublicationRun-off-road accidents tend to be very severe because when a vehicle leaves the road, it will often crash into a solid obstacle (tree, pole, supports, front wall of a culvert, barrier). A statistical analysis of the data shows that Poland's main roadside hazard is trees and the severity of vehicles striking a tree in a run-off-road crash. The risks are particularly high in north-west Poland with many of the roads lined up with...
-
Road texture influence on tire rolling resistance
PublicationTire rolling resistance is one of the most important resistive forces acting on road vehicles. It depends on tire and surface characteristics as well as vehicle operating parameters. This paper deals with the influence of road surface texture on rolling resistance of passenger car tires. Results of road measurements performed on variety of road surfaces are presented.
-
SURFACE & COATINGS TECHNOLOGY
Journals -
MONITORING SYSTEM OF THE ROAD EMBANKMENT
PublicationThe paper presents the analysis of the monitoring system of the embankment supported on concrete columns and overlaid by a load transfer platform with the embedded steel grid. This field investigation was to study the complex interaction among the columns, the load transfer platform layer, and steel grid via in situ measurements during erection and live loading of the embankment. The study was focused on the behaviour of steel...
-
Road safety inspection as a tool for road safety management – the polish experience
PublicationIn Poland, road inspections were implemented in June 2014 on all national roads. Previously conducted traffic surveys mainly related to the technical condition of roads, signs and markings; other safety issues were overlooked. The main problem that occurs during inspection is an inspector’s subjective qualitative assessment which affects the classification of the sources of hazard on the road.. The paper presents an analysis of...
-
The effect of road restraint systems on the level of road safety - Polish experience
PublicationRoadside accidents happen when a vehicle runs off the road. The majority of these accidents are very severe because leaving the road is usually followed by hitting a solid obstacle (tree, pole, support, culvert front wall, barrier). Roadsides are some of the most important issues of road safety. They have been studied for years to identify roadside hazards and the effectiveness of road safety measures such as restraint systems....
-
Baltic Journal of Road and Bridge Engineering
Journals -
Reduction of Tire Rolling Resistance by Optimization of Road Surfaces and Tires
PublicationDuring interaction between tire and road surface three very important phenomena are always in effect. One of them (very desirable) is friction that is important for traction, braking and cornering. Two other phenomena are not desirable at all, that is rolling resistance and noise. This paper discusses relations between road surface and tire parameters versus tire rolling resistance. Road surface texture, porosity, impedance, strength...
-
Temperature influence on tire/road noise evaluated by the drum method
PublicationAmbient air and road surface temperatures substantially affect the road vehicle noise emission. The temperature influence on tire/road noise depends mainly on tire-road combination. It is different for dense and porous pavements, for bituminous and cement ones. It differs also depending on tires. The correction procedures for temperature effect are still under consideration and preparation. Laboratory experiment was prepared to...
-
Pavement ageing influence on tyre/road noise
PublicationRoad surface should be constructed in a way that ensures safe and comfortable traffic conditions, not only when it is newly paved but also during its entire lifetime. An important factor in the asphalt mixture design process is also the expected pavement durability and stability of pavement properties over time. In many countries, road surface starts to play a significant role in traffic noise reduction actions. Selecting a particular...
-
Rolling resistance and tyre/road noise on rubberised asphalt pavement in Poland
PublicationThe paper presents results of tyre/road noise and rolling resistance measurements performed on stone mastics asphalt (SMA) that contains rubberised asphalt, developed and produced by a refinery in Poland. Bituminous binder was modified with polymer and addition of crumb rubber. The first observations of asphalt mixture with the new kind of modified bitumen used on the field section are presented. Rolling resistance of passenger...
-
UN DECADE OF ACTION FOR ROAD SAFETY IN THE NATIONAL ROAD SAFETY STRATEGY UNTIL 2020 – POLISH APPROACH
PublicationPoland continues to have the highest number of road deaths per one million population in the European Union, according to a 2012 European Commission report – in 2011 the rate in Poland was 109 fatalities compared to the EU average of 61 killed. Adopted by the government in 2005 Poland’s National Road Safety Programme GAMBIT 2005 was the response to the EU’s 3rd Road Safety Action Programme. Despite extensive road safety efforts,...
-
Road Infrastructure Safety Management in Poland
PublicationThe objective of road safety infrastructure management is to ensure that when roads are planned, designed, built and used road risks can be identified, assessed and mitigated. Road transport safety is significantly less developed than that of rail, water and air transport. The average individual risk of being a fatality in relation to the distance covered is thirty times higher in road transport that in the other modes. This is...
-
Temperature influence on tyre/road noise of selected tyres
PublicationAir and road temperatures substantially affect road vehicle noise emission. The temperature influence on tyre/road noise depends mainly on tyre-road combination. It is different for dense and porous pavements, for bituminous and cement ones. It differs also depending on tyres. The correction procedures for temperature effect are still under consideration and preparation. Tyre/road noise measurements using CPX method were performed...
-
Modelling fatalities on regional road networks
PublicationDuring the last decade Poland’s road fatalities went down by 44%. The trend differs from region to region. Effective road safetymanagement in regions requires tools for forecasting road safety measures and identifying factors influencing road fatality numbers. Mathematical models can provide such tools. They take into account local characteristics such as: demography, economy, infrastructure and motorization. Such models could...
-
Identifying the Effects of Selected Road and Roadside Parameters on Road Safety Using Geodetic Techniques
PublicationThe paper will present techniques that can be used to obtain data on road alignment and profile including the roadside. In-the-field and simulation studies have helped to develop mathematical models that integrate vehicle position data. The experiments were conducted in a virtual environment using the software ArcGIS that reflects the actual roadside conditions. The site tests were made using a purpose-built device which integrates...
-
The searchlight problem for road networks
PublicationWe consider the problem of searching for a mobile intruder hiding in a road network given as the union of two or more lines, or two or more line segments, in the plane. Some of the intersections of the road network are occupied by stationary guards equipped with a number of searchlights, each of which can emit a single ray of light in any direction along the lines (or line segments) it is on. The goal is to detect the intruder,...
-
Innovative Research Into Road Restraint Systems
PublicationKey to understanding the needs and building road infrastructure management tools to prevent and mitigate run-off-road accidents is to identify hazards and their sources which are a result of wrong design, construction, installation and maintenance of road restraint systems [1]. Building such tools requires advanced studies with field tests, simulations and models to demonstrate the effects of selected parameters on road user safety...
-
Risks to Older People in Road Traffic
Publicationhe article looks at road traffic risks and main trends from the perspective of older road users (drivers, cyclists, pedestrians). With a longer time to react, poor eyesight and hearing, impaired mobility, ill health and medication, older road users are put at risk. A comprehensive and pro-active strategy is needed to deal with these risk factors and meet the safety and mobility needs...
-
Influence of Road Wetness on Tire-Pavement Rolling Resistance
PublicationRolling resistance of tires is one of the most important factors influencing energy consumption of road vehicles, especially on rural roads. For practical reasons, most of rolling resistance measurements are usually performed for dry road conditions. Based on the fact that roads are wet during a considerable time over the year and as part of the projects MIRIAM, ROLRES and ROSANNE, the TUG (Technical University of Gdańsk) in Poland...
-
The effects of vehicle restraint systems on road safety
PublicationKey to understanding the needs and tools of road infrastructure management for preventing run-off-road crashes or minimising their consequences, is to identify the hazads and sources of hazards caused by wrong or improper use of road safety devices and identify errors in the desifn, structure, construction and operation of road safety devices. Studying such an extended scope of the problem required fieldwork and surveys with road...
-
The Effects of Roadside Hazards on Road Accident Severity
PublicationThe risk of becoming involved in an accident emerges when elements of the transport system do not operate properly (man – vehicle – road – roadside). The road, its traffic layout andsafety equipment have a critical impact on road user safety. This gives infrastructural work a priority in road safety strategies and programmes. Run-off-road accidents continue to be one of the biggest problems of road safety with consequences including...
-
Solid road environment and its hazards
PublicationAccidents that involve vehicles departing the road tend to have very high severity, as they often result in the vehicle hitting a permanent obstacle (which can be a ree, a pole, facility pillar, front wall of a culvert or a barrier). In recent years, this type of accident caused approx. 19% of all road deaths in Poland. A particularly high risk can be observed on roads located in northern and western...
-
Road & Transport Research
Journals -
Regional implementation of a road safety observatory in Poland
PublicationThe paper outlines the background and goals of the Road Safety Observatory in the Polish region of Warmia and Mazury. While created it was Poland’s first road safety Observatory, both at the regional and central level. Established in line with the methodology proposed in the European project SafetyNet, together with the planned National Road Safety Observatory it will form part of a Europe-wide network of observatories linked with...
-
Tools for road infrastructure safety management in Poland
PublicationThe objective of road safety infrastructure management is to ensure that when roads are planned, designed, built and used road risks can be systematically identified, assessed, removed and mitigated. There are a number of approaches to road safety management. European Union Directive 2008/96/EC requires EU member states to use four basic tools of road safety infrastructure management. An overview of the methods in these countries...
-
System for monitoring road slippery based on CCTV cameras and convolutional neural networks
PublicationThe slipperiness of the surface is essential for road safety. The growing number of CCTV cameras opens the possibility of using them to automatically detect the slippery surface and inform road users about it. This paper presents a system of developed intelligent road signs, including a detector based on convolutional neural networks (CNNs) and the transferlearning method employed to the processing of images acquired with video...
-
Machine learning applied to acoustic-based road traffic monitoring
PublicationThe motivation behind this study lies in adapting acoustic noise monitoring systems for road traffic monitoring for driver’s safety. Such a system should recognize a vehicle type and weather-related pavement conditions based on the audio level measurement. The study presents the effectiveness of the selected machine learning algorithms in acoustic-based road traffic monitoring. Bases of the operation of the acoustic road traffic...
-
Machine learning applied to acoustic-based road traffic monitoring
PublicationThe motivation behind this study lies in adapting acoustic noise monitoring systems for road traffic monitoring for driver’s safety. Such a system should recognize a vehicle type and weather-related pavement conditions based on the audio level measurement. The study presents the effectiveness of the selected machine learning algorithms in acoustic-based road traffic monitoring. Bases of the operation of the acoustic road traffic...
-
Wojciech Kustra dr inż.
PeopleI am a Faculty member (Assistant Professor, Highway and Transportation Engineering Department) at the Faculty of Civil and Environmental Engineering, Gdansk University of Technology, Poland). My main research interests include: road safety, accident analysis, traffic modeling, transportation planning, traffic engineering, transport management, gis analysis.
-
Surface Chemistry & Experimental Techniques
e-Learning Courseswykłady prowadzone przez prof. G. Jerkiewicza
-
Assessment of Road Restraint Systems in Polish Conditions
PublicationKey to understanding the needs and tools of road infrastructure management is identifying the hazards and their sources involved in having no or faulty road restraint systems. Clarity is also needed on why the systems are wrongly designed, constructed, built and operated. To ensure that the problem is adequately understood, research and site observations were conducted and...
-
INFLUENCE OF MEASURING CONDITIONS ON TYRE/ROAD NOISE
PublicationA decisive factor for the development of tyres and road surfaces is the ability to conduct representative and reproducible measurements of selected characteristics related to the interaction of tyres and road surfaces. In terms of tyre/road noise measurements in Europe two methods described in ISO/FDIS 11819-2 and ECE Regulation No.117 are used. The latter is compulsory for assigning the tyre noise labels. The methodologies differ...
-
ROAD SAFETY FOR CYCLISTS BASED ON THE CALORIES NEEDED
PublicationCyclists are a vulnerable group of road users, especially when no separate infrastructure for cyclists is provided. Then, road factors such as distance and altitude differences can indirectly affect cyclists' safety. Therefore, the authors proposed a procedure based on the geometric characteristics of the road that can determine riding difficulties for cyclists. The proposed procedure can be used both by the public authorities who...
-
Examining the Impact of Distance Between VSL Road Signs on Vehicle Speed Variance
PublicationVariable speed limit (VSL) is an intelligent transportation system (ITS) solution for traffic management. The speed limits can be changed dynamically to adapt to traffic conditions such as visibility and traffic volume, curvature, and grip coefficient of the road surface. The VSL traffic sign location problem and attempts to solve it using computer simulation are presented in this paper. Experiments on a selected road segment,...
-
Hierarchical random models in road transport safety
PublicationIn this paper multilevel approach to the issue of road safety level on the road network of European regions, classified as NUTS 2 in statistical databases of the EU, has been presented. The risk calculated as the number of death casualties in road accidents per 100,000 inhabitants of a given region has Poisson distribution. Therefore, generalized Poisson model has been assumed in the modelling process. Multilevel stochastic analysis...
-
ROAD SAFETY MANAGEMENT TOOLS FOR COUNTRY STRATEGIC LEVEL
PublicationStrategic road safety programmes setting out long-term visions and road infrastructure development plans must be based on road safety forecasts and an understanding of the long-term impact of different measures on road safety. The objective of this paper is to discuss a concept of road safety management for an area of a selected country because there are no simple tools of road safety management for the development and implementation...
-
Acoustic evaluation of road surfaces using different Close Proximity testing devices
PublicationAccording to the valid standard, Close Proximity (CPX) method intends to evaluate the influence of road surfaces on traffic noise. Measurements may be carried out with the use of a self-powered vehicle or a special test trailer equipped with testing tyre towed by another vehicle. Two different testing devices took part in the research organized in Poland in order to determine the ranking of road surfaces in terms of acoustic parameters....
-
Road Restraint Systems as a Basis for Roadside Safety Improvement
PublicationRoadside-related crashes occur when vehicles run off the road. The majority of the crashes have severe outcomes, especially when an object is hit (tree, pole, supports, front wall of a culvert, barrier). These accidents represent app. 19% of all of Poland's road deaths. Roadside crashes involve: hitting a tree, hitting a barrier, hitting a sign or utility pole, vehicle roll-over on the roadside, vehicle roll-over on a slope and...
-
Functionality of road safety devices - identification and analysis of factors
PublicationRoad safety devices are designed to protect road users from the risk of injury or death. The principal type of restraint is the safety barrier. Deployed on sites with the highest risk of run-off-road accidents, safety barriers are mostly found on bridges, flyovers, central reservations, and on road edges which have fixed obstacles next to them. If properly designed and installed, safety barriers just as other road safety devices,...
-
Tools for road infrastructure safety management – Polish experiences
PublicationThe objective of road safety infrastructure management is to ensure that when roads are planned, designed, built and used road risks can be systematically identified, assessed, removed and mitigated. There are a number of approaches to road safety management. European Union Directive 2008/96/EC requires EU member states to use four basic tools of road safety infrastructure management. An overview of the methods in these countries...
-
Low-Temperature Requirements for Bitumen in Central East European Road Construction
PublicationThe paper presents the proposition of special assessment of lowtemperature requirements for bitumens in the region of Central and Eastern Europe where there is a moderate transitional area from sea to the continental type of climate. The results of the research program conducted on the road neat bitumens, Styrene-Butadiene-Styrene polymer and polymer-rubber modified bitumen, and multigrade bitumen types were presented and discussed....
-
Regional Observatory as a Part of Road Safety Information System
PublicationEU experience clearly indicates that it is necessary to inform and motivate the public on road unsafety to undertake specific preventive efforts, as well as making road users feel responsible for the state of road safety and seek to improve this state gradually to protect their health and life. The implementation of the Warmia-Mazury Road Safety Observatory project will not only be an excellent addition to the activities carried...
-
Regional observatory as a part of road safety information system
PublicationEU experience clearly indicates that it is necessary to inform and motivate the public on road unsafety to undertake specific preventive efforts, as well as making road users feel responsible for the state of road safety and seek to improve this state gradually to protect their health and life. The implementation of the Warmia-Mazury Road Safety Observatory project will not only be an excellent addition to the activities carried...
-
Injury Prediction Models for Onshore Road Network Development
PublicationIntegrating different modes of transport (road, rail, air and water) is important for port cities. To accommodate this need, new transport hubs must be built such as airports or sea ports. If ports are to grow, they must be accessible, a feature which is best achieved by building new roads, including fast roads. Poland must develop a network of fast roads that will provide good access to ports. What is equally important is to upgrade...
-
The use of GIS tools for road infrastructure safety management
PublicationThere are many factors that influence accidents and their severity. They can be grouped within the system of man, vehicle and environment. The article focuses on how GIS tools can be used to manage road infrastructure safety. To ensure a better understanding and identification of road factors, GIS tools help with the acquisition of road parameter data. Their other role is helping with a clear and effective presentation of risk...
-
Pedestrian Safety in Road Traffic in Poland
PublicationEvery third road accident in Poland involves a pedestrian as a participant or, most of the time, a casualty. Pedestrian accidents are usually the result of complex situations and the outcome of a number of factors related to driver and pedestrian behaviour and road infrastructure. Safety depends largely on how well the traffic condition is perceived and on visibility in traffic. The paper presents the results of analyses of methodologies...
-
Modernization of the Trailer for Tyre/Road Rolling Resistance Measurements
PublicationIn the article the ways of defining tyre rolling resistance are presented. The advantages of the laboratory tests of tyre/road rolling resistance and the advantages and disadvantages of on the road tyre/road rolling resistance tests are described. The description of the special trailer used for tyre/road rolling resistance measurements designed and constructed in the Faculty of Mechanical Engineering at Gdansk University of Technology,...
-
INFLUENCE OF TEST CONDITIONS ON TYRE/ROAD NOISE MEASURED BY THE DRUM METHOD
PublicationTyre/road noise is one of the most important environmental problems related to road traffic. Nowadays a few standard procedures of tyre/road noise measurements are in use. Unfortunately, measurement conditions specified within relevant standards are very different. For example, procedure described in ISO 11819-2 used for pavement investigations requires tyre load of 3200 N and capped inflation pressure of 200 kPa. At the same time...
-
The two ring road complexes of Gdansk
PublicationThe urban structure of Gdańsk city centre is determined by two ring road complexes. The first of them, the Gdańsk Ring, has been designed by Hermann Josef Stübben as a result of a defortification at the turn of the 19th and 20th centuries. This new modern zone of the city centre was destroyed like the rest of Gdańsk in the end of World War Two and had not been reconstructed as a result of de-Germanization of the Recovered Territories....