Search
Search results for: cantilever
-
Crack identification in cantilever beam using wavelets
PublicationPrzedstawiono metodę identyfikacji zniszczeń przy użyciu transformacji falkowej. Rozpatrzono przykład belki wspornikowej. Pokazano, że transformacja falkowa wykrywa miejsce zniszczenia.
-
Process zone in the Single Cantilever Beam under transverse loading. - Part II: Experimental
PublicationThis paper describes an experimental arrangement to evaluate stress/strain fields in the process zone of asymmetric adhesively bonded joints. A transparent polycarbonate flexible beam was bonded to an aluminium alloy rigid block with an epoxy adhesive in a Single Cantilever Beam (SCB) configuration. The flexible adherend was loaded in the direction parallel to the initial crack front at constant rate. To monitor strains induced...
-
Free Vibration of Cantilever Bars Having a Shape of Solid and Hollow Curvilinear Truncated Cone
Publication -
Design and simulation of a new prototype of piezoelectric cantilever sensor/actuator for analysis of the soft tissues properties
PublicationThis paper is devoted to a new prototype of piezoelectric cantilever transducer dedicated for the characterization of the mechanical properties of soft tissues. General description of the actuator’s structure is presented including the basic principles of the measurement. The chosen geometry of the prototype is discussed and compared with the existing one. Constitutive equations are presented for the active and passive layer of...
-
Process zone in the Single Cantilever Beam under transverse loading. - Part I: Theoretical analysis
PublicationSingle Cantilever Beam (SCB) specimen loaded with a transverse force parallel to the crack front is proposed for the analysis of crack propagation phenomena under mixed mode conditions. The stress redistribution in the adhesive layer in the vicinity of the crack front so as the beam deformation are estimated using a Timoshenko beam on elastic foundation model. This model emphasizes the Mode II contribution due to flexural beam...
-
Analysis of free vibrations of cantilever bars with parabolically variable cross-sections using the Rayleigh’s method
Publication -
Force transfer and stress distribution in short cantilever deep beams loaded throughout the depth with a various reinforcement
PublicationDeep beams used as the main reinforced concrete structural elements which taking over the load and stiffening construction are often found in high-rise buildings. The architecture of these buildings is sometimes sophisticated and varied, arouse the admiration of the majority of recipients, and thus causing an engineering challenge to correctly design the structural system and force transfer. In such structures is important to shape...
-
Cable-stayed cantilever structures as an expat of unique application in the construction of a building located in seismic area – an author’s project of multifunctional building in Lisbon, Portugal
PublicationThe article presents numerical simulations for the modelling of seismic impact on the structure of unique cantilever cablestayed structure with application of two methods. The Response Spectrum method, in which a spectrum of the structure's responses to an earthquake's impact is generated and the Accelerogram method, in which we generate dynamic load in the form of a diagram of the connection between acceleration and time for...
-
Non-destructive diagnostics of concrete cantilever beam and slab by impact echo method = Nieniszcząca diagnostyka konstrukcji betonowych belek wspornikowych i płyty stropowej za pomocą metody impact echo
PublicationPraca poświęcona jest zastosowaniu fal sprężystych na przykładzie w metody impact-echo. Metoda ta wykorzystuje zjawisko propagacji fal wzbudzanych przez mechaniczne uderzenie i ich pomiar za pomocą jednego lub dwóch akcelerometrów. Przeprowadzone testy eksperymentalne dla betonowych wsporników oraz stropu potwierdziły skuteczność metody w wykrywaniu uszkodzeń.
-
Experimental and numerical analysis of an aluminum cantilevered beam with polymer adhesive
PublicationIn this paper, experimental and numerical investigation on a composite cantilevered aluminum beam has been conducted. The subject of the study consists of two plain aluminum elements bonded with polymer adhesive of different thickness. It has been proven in the previous study that this kind of material has high damping properties. During an experimental investigation, value of damping ratios have been obtained. The aim of a numerical...
-
Alternative way of the main reinforcement anchorage in reinforced short cantilevers
PublicationThe results of the experimental investigation of the reinforced corbels and dapped end beams with steel studs were introduced in the work. The efficiency of this type of the reinforcement was compared with the typical reinforcenet applied in reinforced conctrete construcions.
-
Integration of Fluorescent, NV-Rich Nanodiamond Particles with AFM Cantilevers by Focused Ion Beam for Hybrid Optical and Micromechanical Devices
PublicationIn this paper, a novel fabrication technology of atomic force microscopy (AFM) probes integrating cantilever tips with an NV-rich diamond particle is presented. Nanomanipulation techniques combined with the focused electron beam-induced deposition (FEBID) procedure were applied to position the NV-rich diamond particle on an AFM cantilever tip. Ultrasonic treatment of nanodiamond suspension was applied to reduce the size of diamond...
-
Focused ion beam-based microfabrication of boron-doped diamond single-crystal tip cantilevers for electrical and mechanical scanning probe microscopy
PublicationIn this paper, the fabrication process and electromechanical properties of novel atomic force microscopy probes utilising single-crystal boron-doped diamond are presented. The developed probes integrate scanning tips made of chemical vapour deposition-grown, freestanding diamond foil. The fabrication procedure was performed using nanomanipulation techniques combined with scanning electron microscopy and focused ion beam technologies....
-
EXPERIMENTAL AND THEORETICAL FLOW OF THE FORCES IN DEEP BEAMS WITH CANTILEVAR
PublicationThis article presents the results of experimental research carried out on deep beams with cantilever which was loaded throughout the depth. The main deep beam was directly simply supported on the one side. On the other side the deep beam was suspended in another deep member situated at right angles. All deep beams created a spatial arrangement. The paper is focused on the analysis of the cracks morphology and flow of the internal...
-
The influence of reinforcement on load carrying capacity and cracking of the reinforced concrete deep beam joint
PublicationThe paper presents the results of experimental research of the spatial reinforced concrete deep beam systems orthogonally reinforced and with additional inclined bars. Joint of the deep beams in this research was composed of the longitudinal deep beam with a cantilever suspended at the transversal deep beam. The cantilever deep beam was loaded throughout the depth and the transversal deep beam was loaded at the mid-span by longitudinal...
-
Wpływ ukształtowania zbrojenia na zarysowanie i nośność żelbetowego węzła tarczowego ze wspornikiem
PublicationPraca ma charakter eksperymentalno-teoretyczny i dotyczy zagadnień związanych z żelbetowymi tarczami pracującymi w przestrzennym układzie konstrukcji budynków. Celem niniejszej dysertacji było określenie wpływu głównych parametrów jakimi są sposób ukształtowania zbrojenia i smukłość ścinania na zarysowanie i nośność żelbetowego przestrzennego węzła tarczowego ze wspornikiem. Na podstawie aktualnego stanu wiedzy, opracowano program...
-
Adhesive Monitoring with Instrumented Wedge Test
PublicationThe wedge test (sometimes called the Boeing wedge test) is amongst the most readily exploitable techniques for assessment of the rate-dependent fracture energy of adhesive materials when used to bond relatively rigid substrates. With its siblings: the double cantilever beam (DCB), and the tapered double cantilever beam (TDCB), a force is applied, essentially in cleavage, to provoke substrate separation perpendicularly to the bondline...
-
Detection of Closing Crack in Beam Based on Responses Induced by Harmonic Excitation
PublicationThe non-linear contact model was chosen to simulate the closed crack in the cantilever beam. The study examines the shape and characteristics of the phase diagram of a cantilever beam with closed cracks. It investigates how various crack properties influence the geometry of the phase diagram and proposes a method for identifying cracks based on their features. The area of each closed curve in the phase diagram is determined using...
-
Non-Linear Analysis of Structures Utilizing Load-Discretization of Stiffness Matrix Method with Coordinate Update
PublicationThis paper proposes a stiffness method based structural analysis algorithm for geometrically non-linear structures. In this study, the applied load on the joints has been discretized to a sequence of a few loadings applied. Each loading step produces incremental external nodal displacements, which are added to the corresponding coordinates to get a new geometrical shape of the structure. This process is iteratively repeated until...
-
Experimental tests of reinforced concrete deep-beams
PublicationThe paper presents results of experimental research of the reinforced concrete deep beam with a spatial arrangement. Tested structural elements consist of the cantilever deep beam loaded on the height and transverse deep beam with hanging on it another one. The analysis includes crack morphology, effort of steel and load distribution. The article verified effectiveness of two different kind of reinforcement in both tested deep...
-
A new prototype of piezoelectric bending resonant transducer for analysis of soft tissues properties
PublicationThis paper is devoted to a new piezoelectric bending resonant transducer prototype dedicated to the characterization of the mechanical properties of soft tissue. A general description of the actuator’s structure is presented including the basic principles of the measurement. The chosen geometry of the prototype is discussed and compared with the existing version. Constitutive equations are presented for the active and passive layer...
-
Corrosion process monitoring by AFM higher harmonic imaging
PublicationThe atomic force microscope (AFM) was invented in 1986 as an alternative to the scanning tunnelling microscope, which cannot be used in studies of non-conductive materials. Today the AFM is a powerful, versatile and fundamental tool for visualizing and studying the morphology of material surfaces. Moreover, additional information for some materials can be recovered by analysing the AFM's higher cantilever modes when the cantilever...
-
OPTICAL STRAIN MEASUREMENT OF CONCRETE VERSUS MANUAL EXTENSOMETER MEASUREMENT BASED ON THE TEST RC DEEP BEAM IN A COMPLEX STATE OF STRESS
PublicationThe purpose of this study is to compare the strain measurement techniques of concrete in R-C element subjected to the monotonic load up to the failure. In the analysis manual extensometer methods of measurements and the optical system ARAMIS for non-contact three-dimensional measurements of deformation was used. The test sample was a cantilever deep beam loaded throughout the depth which was a part of the reinforced concrete deep...
-
Antagonist adhesion effects due to variable substrate surface
PublicationThe effects of variability of intrinsic adhesion within a joint have been studied using a single cantilever beam (SCB) test. Fracture energy was found not to be a simple function of relative areas of 2 surface pre-treatments: a 'weak' zone decreased strength more than expected from simple, additive considerations. By severing the adhesive along the strong-weak transition, fracture energy increased.The prior antagonist effect appears...
-
Enhancing capabilities of Atomic Force Microscopy by tip motion harmonics analysis
PublicationMotion of a tip used in an atomic force microscope can be described by the Lennard-Jones potential, approximated by the van der Waals force in a long-range interaction. Here we present a general framework of approximation of the tip motion by adding three terms of Taylor series what results in non-zero harmonics in an output signal. We have worked out a measurement system which allows recording of an excitation tip signal and its...
-
Piezo 2011, Electroceramics for End-Users VI
PublicationThis work extends a power harvesting with using piezoelectric materials. Experimental presents the development of a piezoelectric MEMS generator which has the ability to scavenge mechanical energy of ambient vibrations from their surroundings and transform it into electrical energy that can be used in energy storage applications. Recent literature shows that piezoelectric transduction has received the most attention for vibration-to-electricity...
-
High-quality Experiment Dedicated to microGravity Exploration, Heat Flow and Oscillation Measurement from Gdańsk
PublicationIn this paper we propose HEDGEHOG (High-quality Experiment Dedicated to microGravity Exploration, Heat flow and Oscillation measurement from Gdańsk) REXUS experiment to investigate vibrational and heat flow phenomena during the whole (ascent, microgravity phase, descent and recovery) flight of a sounding rocket. First, a proposed system of cantilever beams is discussed to study dynamic behaviour of dummy payload. Dimensioning has...
-
Force-deformation spectroscopy in contact mode
Open Research DataThe deformation-distance spectroscopic curve is obtained by registering the value of the probe cantilever deflection as a function of the elongation of the piezoelectric scanner. It assumes a simple relationship in the form of Hooke’s law, linking the deformation of the lever with the amount of its deflection caused by the proximity of the probe and...
-
Accurate and continuous adhesive fracture energy determination using an instrumented wedge test
PublicationThe wedge test and the related double cantilever beam test are practical methods of assessing structural adhesive fracture energy. In the former, and to a lesser extent the latter, a recognised problem is the difficulty of following the length of the growing crack, required to calculate fracture energy with any accuracy. We present a novel method of measurement of crack length that has the advantages of being accurate and allowing...
-
Imaging of ferroelectric properties of sinter by means of Piezoresponse Force Microscopy
Open Research DataFerroelectricity is a property of certain materials [1], characterized by a spontaneous electrical polarization that can be reversed by applying an external electric field. Ferroelectric properties can be used to make capacitors with adjustable capacity. The permeability of ferroelectrics is not only regulated, but usually also very high, especially...
-
Effect of adhesive compliance in the assessment of soft adhesives with the wedge test
PublicationWedge tests are usually analysed assuming that the free, unbonded members may be treated as encastré cantilever beams. However, if the adhesive layer is sufficiently flexible (e.g., due to low elastic modulus), then significant strain in the bonded region may occur and lead to modification of the behaviour outside this region. Using in conjunction a sensitive strain gauge method on asymmetric wedge tests and a mathematical analysis...
-
Diagnostics and monitoring of the longest span extradosed bridge in Europe
PublicationThe article presents complex diagnostic procedures applied for the purpose of behavior analysis of the extradosed bridge with the longest span in Europe that was built in 2018 in Poland. The system of health monitoring was used to: register internal forces in temporary supports, monitor concrete bonding, perform in situ diagnostics and operation tests. The bridge is a continuous four-span structure with spans theoretical lengths...
-
Investigating lubricants behaviour in microgravity for vibration damping purposes
PublicationVibration is one of the harshest environments an object is exposed to during and after launch into space on a launch vehicle. Such vibrations should be damped to avoid destruction of the spacecraft or its elements. Currently, active and material damping is used. A possibility of using lubrication as the damping factor is suggested by some research. MoS2 is a typical solid lubricant used in space applications. Its properties vary...
-
A new hyperbolic-polynomial higher-order elasticity theory for mechanics of thick FGM beams with imperfection in the material composition
PublicationA drawback to the material composition of thick functionally graded materials (FGM) beams is checked out in this research in conjunction with a novel hyperbolic‐polynomial higher‐order elasticity beam theory (HPET). The proposed beam model consists of a novel shape function for the distribution of shear stress deformation in the transverse coordinate. The beam theory also incorporates the stretching effect to present an indirect...
-
Experimental Study on the Effectiveness of Polyurethane Flexible Adhesive in Reduction of Structural Vibrations
PublicationThe aim of the present study is to consider the idea of using polyurethane flexible adhesive in to reduce the vibrations in structures exposed to dynamic loads and evaluate their damping properties in relation to large deformations. Firstly, two aluminium cantilever beams, simulating structural elements (without and with polyurethane layer in the form of tape), were analysed, in order to check the damping of the unconstrained polymer...
-
Hyperelastic Microcantilever AFM: Efficient Detection Mechanism Based on Principal Parametric Resonance
PublicationThe impetus of writing this paper is to propose an efficient detection mechanism to scan the surface profile of a micro-sample using cantilever-based atomic force microscopy (AFM), operating in non-contact mode. In order to implement this scheme, the principal parametric resonance characteristics of the resonator are employed, benefiting from the bifurcation-based sensing mechanism. It is assumed that the microcantilever is made...
-
Fabrication and characterization of boron-doped nanocrystalline diamond-coated MEMS probes
PublicationFabrication processes of thin boron-doped nanocrystalline diamond (B-NCD) films on silicon-based micro- and nano-electromechanical structures have been investigated. Nanocrystalline boron doped -diamond (B-NCD) films were deposited using Microwave Plasma Assisted Chemical Vapour Deposition (MW PA CVD) method. The variation of B-NCD morphology, structure and optical parameters were particularly investigated. The use of truncated...
-
Karol Grębowski dr inż.
PeopleKarol Grębowski (M.Sc.) works as an assistant at the Department of Technical Fundamentals of Architecture Design of the Faculty of Architecture at Gdansk University of Technology. His scientific research deals with dynamic phenomena occurring during the vibration of structures, bridges, and studies the design methodology of the elements forming passive protection system of the vehicles degraded by struck or explosion in the context...