Search results for: condition monitoring
-
Manifestation of Intermolecular Interactions in the IR Spectra of 2- and 4-Methylmethcathinones Hydrochlorides: DFT Study and Hirshfeld Surfaces Analysis
PublicationThis paper reports a Hirshfeld surfaces analysis of crystalline 2- and 4-methylmethcathinone (2-MMC and 4-MMC) hydrochlorides to analyze NH∙Cl and CH∙∙∙Cl intermolecular interactions and approve the formation of the NН2+–Cl– salt fragment in both 2-MMC∙HCl and 4-MMC∙HCl crystals. Two isomeric dimers were separated from the corresponding crystal packing to model IR spectra of the crystalline 2-MMC∙HCl...
-
GPR investigation of the strengthening system of a historic masonry tower
PublicationIn this paper the condition assessment of the strengthening system of a masonry tower was carried out by the GPR method. The study provided unique experimental data acquired during measurements of the reinforced concrete frame embedded in masonry walls. Conducted numerical and experimental investigations were focused on the phenomenon of the diffraction-refraction scattering of the electromagnetic energy. A hyperbola resulting...
-
Reservoir Influence on Pressure Wave Propagation in Steel Pipes
PublicationThe relation between the length of steel pipe and the pressure wave period in the system, reservoir-pipe-valve, is discussed. Experiments carried out for the short steel pipes showed that in such a system, the pressure wave celerity estimated using the measured wave cycles systematically increases with the increase of the pipe length. The observed differences can exceed even 90 m=s. As the pressure wave traveling in the pipe with...
-
Impact of adverse winter weather on traffic flow
PublicationThe paper aims to analyse the impact of adverse weather in winter on traffic flow using data from a dual carriageway section of an express road located in Gdansk. For the purposes of the analysis, traffic and meteorological data were collected for a period of 15 months in 2014-2015 and aggregated to 5 minutes intervals. The impact of winter weather conditions on traffic flow was assessed by comparing aggregated traffic stream parameters...
-
Economical methods for measuring road surface roughness
PublicationTwo low-cost methods of estimating the road surface condition are presented in the paper, the first one based on the use of accelerometers and the other on the analysis of images acquired from cameras installed in a vehicle. In the first method, miniature positioning and accelerometer sensors are used for evaluation of the road surface roughness. The device designed for installation in vehicles is composed of a GPS receiver and...
-
Updating the Coupling Algorithm between HYDRUS and MODFLOW in the HYDRUS Package for MODFLOW
PublicationThe HYDRUS-based flow package for MODFLOW (the HPM or the HYDRUS package) is an existing unsaturated zone flow package for MODFLOW. In MODFLOW with the HPM, the groundwater modeling domain is discretized into regular grids that can be combined into multiple zones based on similarities in soil hydrology, topographical characteristics, and the depth to the groundwater. Each of these zones is assigned one unsaturated soil profile...
-
ANALYSIS OF THE IMPACT OF THE PLANNED SEWAGE DISCHARGE FROM THE ‘NORTH’ POWER PLANT ON THE VISTULA WATER QUALITY
PublicationThe paper presents results of analysis of the industrial sewage discharge impact from the ‘North’ Power Plant on the Vistula water quality around 45+330 of the river kilometer. For the analysis, the two-dimensional models of flow, impurities and temperature transport were used. Hydrological conditions of the analyzed section of the river, characteristic flows and bathymetry of the riverbed in the first instance were defined....
-
Noise and Rolling Resistance Properties of Various Types of Winter Tyres Compared to Normal Car Tyres
PublicationTo cope with winter weather conditions, potentially including snow and ice, it is common to use winter tyres, or ”all-seasons” tyres assumed to be safe both in summer and winter. In some northern countries, winter tyres are mandatory. Traditionally, it has been assumed that winter tyres are noisier than normal tyres (here called summer tyres) and winter tyres equipped with studs are assumed to be very noisy.This paper presents...
-
Late cultivars of cabbage can better cope with cadmium- involved stress than early one
PublicationThe usefulness of white cabbage (Brassica oleracea ssp. capitata L. f. alba) for phytoremediation of heavy metals (cadmium and zine) due to the rapid growth and a large biomass of its heads has been already described (Bączek-Kwinta et al., 2011. Kusznierewicz et al., 2012). As the photosynthetic apparatus supplies the whole plant with sugars necessary for various physiological processes and, in consequence, results in the yield,...
-
Thermo-oxidative exfoliation of carbon black from ground tire rubber as potential reinforcement in green tires
PublicationConsidering the balance between rapidly growing global tire demand and scarcity of natural resources, recycling and reclaiming techniques of tire rubber have become the state of the art. Herein, we set out to implement a self-designed thermo-oxidative reactor for the exfoliation of carbon black (CB) from ground tire rubber, which is efficiently functioned under a thermo-oxidative reclaiming condition without any additive. The exfoliation...
-
POLDER AND CITY: SUSTAINING WATER LANDSCAPES ON AN URBAN EDGE
PublicationThe question investigated in this paper is how to maintain the environmental quality of the polder landscape encompassing the city in the condition of urban pressure on this landscape. On the basis of theoretical approaches, historical surveys and introductory study models new ideas are tested on the case study of Gdansk, a city located in the Vistula River delta in northern Poland. Research shows that the city was created as a...
-
Ice Phenomena in River Mouths
PublicationRiver outlets located in tideless areas are analyzed in this paper. First, ice processes in the St Clair River mouth are presented. The river mouth, called St. Clair Flats is a typical river delta located on the shore of Lake St. Clair. Based on this example ice jam formation in river delta has been analyzed followed by a presentation of the main mechanism of ice jam formation. The Vistula River mouth is a man-made, artificial...
-
The reduction of auxiliaries power demand: The challenge for electromobility in public transportation
PublicationAn important role in the consumption of electric energy in urban transport are non-traction needs (auxiliaries), the main part of which is heating and air condition (HVAC). Auxiliaries are responsible for almost half of total energy consumption (normal weather conditions) and in the winter (or hot summer) it reaches up to 70% in daily scale. The reduction of energy used for non-traction needs is currently the main challenge related...
-
Protection and renovation of public areas in a modernist city: the case of three streets in the historic City Centre of Gdynia
PublicationThis article concerns issues related to the preservation and restoration of public space in Gdynia’s city centre, which was designed and built mainly in the 1920s and 1930s. In 2007, a major part of the city centre was entered into the register of monuments asa historic complex of urban architecture. Moreover, in 2015, the area was declared a Monument of History. Protection of a complex of urban architecture covers not only the...
-
Development of the System Assurance Reference Model for Generating Modular Assurance Cases
PublicationAssurance cases are structured arguments used to demonstrate specific system properties such as safety or security. They are used in many industrial sectors including automotive, aviation and medical devices. Larger assurance cases are usually divided into modules to manage the complexity and distribute the work. Each of the modules is developed to address specific goals allocated to the specific objects i.e. components of the...
-
Nonlinear free and forced vibrations of a dielectric elastomer-based microcantilever for atomic force microscopy
PublicationThe majority of atomic force microcode (AFM) probes work based on piezoelectric actuation. However, some undesirable phenomena such as creep and hysteresis may appear in the piezoelectric actuators that limit their applications. This paper proposes a novel AFM probe based on dielectric elastomer actuators (DEAs). The DE is modeled via the use of a hyperelastic Cosserat model. Size effects and geometric nonlinearity are included...
-
Selection of Organic Coating Systems for Corrosion Protection of Industrial Equipment
PublicationThe most important element of corrosion protection in industrial conditions is the protective coating system. However, selecting the right coating can often be a real problem due to the sheer number of coating manufacturers and their products on the market. A quantitative approach based on the data mining technique used to analyze the obtained multi-site exposure data has been proposed. This was demonstrated by the example of the...
-
Just Let Me Think: Designing Against Acquired Illiteracy.
PublicationThis article concerns the relatively new problem of illiteracy relating to persons previously being literate, which is caused by too intensive using of so-called digital media (TV, computers, tablets, smartphones, e-book readers, portable media players, etc.). The problem has been observed for several years mainly in countries with high economic and technological development. The widespread use of digital media and the ease of...
-
THREE-DIMENSIONAL numerical investigation of MHD nanofluid convective heat transfer inside a CUBIC porous container with corrugated bottom wall
PublicationSimultaneous use of porous media and nanofluid as a heat transfer improvement method has recently captivated a great deal of attention. The heat transfer and entropy production of the Cu-water nanofluid inside a cubic container with a heated bottom wavy wall and an elliptic inner cylinder were numerically analyzed in this study. The container is partitioned into two sections: the left side is filled with permeable media and...
-
Materiały do poznania ważek (Odonata) Pojezierza Litewskiego (Polska północno-wschodnia), ze szczególnym uwzględnieniem Suwalskiego Parku Krajobrazowego, zebrane przy okazji XIX Sympozjum Sekcji Odonatologicznej Polskiego Towarzystwa Entomologicznego w 2023 r.
PublicationFrom 6-9 July 2023, the participants of the 19th Symposium of the Odonatological Section of the Polish Entomological Society carried out fieldwork on the dragonflies in and around the Suwałki Landscape Park (SPK) (NE Poland). The symposium was preceded by a field reconnaissance (8-10 June). The results of this fieldwork, which yielded 45 species at 22 sites, are presented and discussed. Three species...
-
Scoreboard Architectural Pattern and Integration of Emotion Recognition Results
PublicationThis paper proposes a new design pattern, named Scoreboard , dedicated for applications solving complex, multi-stage, non-deterministic problems. The pattern provides a computational framework for the design and implementation of systems that integrate a large number of diverse specialized modules that may vary in accuracy, solution level, and modality. The Scoreboard is an extension of Blackboard design pattern and comes under...
-
Re-use of historic wooden verandas in Sopot, Poland
PublicationSopot is the best-known seaside resort in Poland. The city is unique with regard not only to its location and natural values, but also its interesting architecture, which dates back to the end of the 19th and the beginning of the 20th century. Wooden verandas are one of the characteristic features of Sopot architecture. Their origin is associated with the Swiss style, which was fashionable at the turn of the 20th century and quite...
-
A method to monitor urinary carbon dioxide in patients with septic shock
PublicationSevere sepsis and septic shock are life-threatening conditions with mortality rates exceeding 31% (Levy et al., 2012) [1]. Septicemia was the most expensive US hospital condition in 2011 (Torio and Andrews, 2006)[2]. Urinary carbon dioxide may provide rapid, clinically useful information about a patient’s status, empowering physicians to intervene earlier and improve septic shock mortality. The objective of this paper is to validate...
-
Temperature influence on tyre/road noise on poroelastic road surface based on laboratory measurements
PublicationThe temperature effect on measured tyre/road noise is very important phenomena as it may lead to significant errors in measurement results due to substantial influence of this parameter on the obtained values. It depends mainly on the particular tyre-road combination. It is different for dense and porous as well as for bituminous and cement concrete pavements. It differs also depending on tested tyre. The correction procedure for...
-
An application for a new type of pneumatic engine concept
PublicationHeavy trucks are often equipped with loading and unloading systems like dock levellers with swing lip or telescopic lip. Most of these devices require hydro-electrical energy supply systems (eg. the pump that presses the working substance to the actuators must be propelled by electric engine.) The space taken by pump with electric engine can be reduced on condition that a new type of pneumatic drive will be considered. It is possible...
-
A new type of (TiZrNbTaHf)N/MoN nanocomposite coating: Microstructure and properties depending on energy of incident ions
PublicationA novel (TiZrNbTaHf)N/MoN nanocomposite coatings, which consist of the nitride of the high-entropy alloy and the binary nitride, were synthesized by vacuum-arc deposition at various substrate biases. The elemental composition, chemical bonding state, phase structure, microstructure and mechanical properties of the coatings were studied by high-resolution experimental methods: SIMS, GDMS, XPS, XRD, HR-TEM and nano-indentation. It...
-
Modeling of lapping plate wear and conditioning in single-sided lapping
PublicationIn order to achieve higher quality on worked surfaces with lower roughness, very high accuracy of shape and dimensions it is crucial to improve conventional finishing technologies and to develop new working principles. Single-sided lapping is one of the most effective planarization technologies and it is determined by a number of factors and boundary conditions. The most significant influence over a dimensional and profile accuracy,...
-
Reinforced concrete thin wall dome after eighty years of operation in maritime climate environment
PublicationThe paper presents a description of the construction elements of the Gdynia Seaport main hall dome. Firstly, it provides information about the technical condition of the dome’s structure. Secondly, it examines the strength analysis of the thin-walled reinforced concrete dome covering. Throughout the last 80 years the building has been exposed to an unfavourable marine climate. The analysis of the state of stress and deformations...
-
Factors determining accumulation of bisphenol A and alkylphenols at a low trophic level as exemplified by mussels Mytilus trossulus
PublicationThe aim of the study was to investigate abiotic and biotic factors influencing the accumulation of endocrine disrupting compounds (EDCs) such as bisphenol A (BPA), 4-tert-octylphenol (OP) and 4- nonylphenol (NP) in mussels Mytilus trossulus from the Gulf of Gdansk (Southern Baltic). The key abiotic factor influencing BPA, OP and NP accumulation in mussels is their hydrophilicity/lipophilicity, which affects their main assimilation...
-
Technology convergence and digital divides. A country-level evidence for the period 2000–2010
PublicationThe paper, mostly empirical in nature, investigates issues on cross-national new information and communication technologies (ICTs) adoption patterns and growth directions. In the period of 2000–2010, a great number of countries underwent substantial changes on the field of ICTs implementation. Many of them made a great “jump” starting with almost “zero level” of ICTs adoption in the year 2000 and during the ten- year period were...
-
Visual measurement system for chosen parameters of current collectors
PublicationA current collector is an element in a traction vehicle, used for movable, contact con-nection between the main circuit of this vehicle and the contact line. Bad technical condi-tion of these important elements in the main circuit of the vehicle result in its incorrect cooperation with contact line. Periodic control of technical condition of current collectors ensures infallible current collection. The pantograph diagnostics consists...
-
Coupled nonlinear Schrödinger equations in optic fibers theory
PublicationIn this paper a detailed derivation and numerical solutions of CoupledNonlinear Schr¨odinger Equations for pulses of polarized electromagnetic wavesin cylindrical fibers has been reviewed. Our recent work has been compared withsome previous ones and the advantage of our new approach over other methods hasbeen assessed. The novelty of our approach lies is an attempt to proceed withoutloss of information within the frame of basic...
-
Landscape as a Potential Key Concept in Urban Environmental Planning: The Case of Poland
PublicationRapid urban development increases the consumption of materials, energy, and water, resulting in an overproduction of waste and emissions. These cause many environmental threats, such as ozone layer depletion and rain acidification, leading to climate change. Therefore, the question arises on how to improve the effectiveness of tools that strengthen environmental protection. This discursive article presents an approach stressing...
-
EVALUATION OF EFFECTIVENESS OF WATERJET PROPULSOR FOR A SMALL UNDERWATER VEHICLE
PublicationT he goal of the project described is to replace the existing propulsion system of a small underwater vehicle with a solution less prone to mechanical damage and ensuring a lower risk of the entanglement of fibrous objects suspended in the body of water. Four typical marine screws are utilised in the current design of the vehicle. One possible solution of the problem is the application of waterjet propulsors located...
-
SPECTRAL RESPONSE OF STATIONARY JACK-UP PLATFORMS LOADED BY SEA WAVES AND WIND USING PERTURBATION METHOD
PublicationThe paper addresses non-linear vibrations of offshore jack-up drilling platforms loaded by sea waves and wind in their stationary condition using the perturbation method. Non-linearity of dynamic equations of motion for fixed offshore platforms yields from two factors. The first is load excitation generating non-linear velocity coupling in a dynamic system. This coupling is inherent in the modified Morison equation, involving the...
-
Numerical analysis of vacuum drying of a porous body in the integrated domain
Publicationn the present study, the vacuum drying process of an apple slice is numerically modeled based on a control volume method. Transient two-dimensional Navier– Stokes, energy, moisture, and Luikov equations are solved by numerical coding (Fortran) to simulate the simultaneous heat and mass transfer in the ambient and apple slice, respectively. The privilege of using Luikov's model is that the capillary forces are considered, and a...
-
Thermo-Mechanical Simulation of Underwater Friction Stir Welding of Low Carbon Steel
PublicationThis article investigates the flow of materials and weld formation during underwater friction stir welding (UFSW) of low carbon steel. A thermo-mechanical model is used to understand the relation between frictional heat phenomena during the welding and weld properties. To better understand the effects of the water environment, the simulation and experimental results were compared with the sample prepared by the traditional friction...
-
Predicting the seismic collapse capacity of adjacent SMRFs retrofitted with fluid viscous dampers in pounding condition
PublicationSevere damages of adjacent structures due to structural pounding during earthquakes have emphasized the need to use some seismic retrofit strategy to enhance the structural performance. The purpose of this paper is to study the influence of using linear and nonlinear Fluid Viscous Dampers (FVDs) on the seismic collapse capacities of adjacent structures prone to pounding and proposing modification factors to modify the median...
-
Wavelet Transform Analysis of Heart Rate to Assess Recovery Time for Long Distance Runners
PublicationThe diagnostics of the condition of athletes has become a field of special scientific interest and activity. The aim of this study was to verify the effect of a long (100 km) run on a group of runners, as well as to assess the recovery time that is required for them to return to the pre-run state. The heart rate (HR) data presented were collected the day before the extreme physical effort, on the same day as, but after, the physical...
-
THE RISE OF FISCAL OPACITY IN POLAND IN THE ERA OF THE COVID-19 PANDEMIC
PublicationResearch background: The quality of information provided by the fiscal authorities and the correct flow of this information between them and the society are very important especially in times of crisis, when there is an imbalance in public finances and an increasing public debt. Ensuring fiscal transparency (transparency of public finances) reduces fiscal risk and corruption and supports public acceptance of fiscal reforms. Purpose...
-
Molecular Strategy for Survival at a Critical High Temperature in Eschierichia coli
PublicationThe molecular mechanism supporting survival at a critical high temperature (CHT) in Escherichia coli was investigated. Genome-wide screening with a single-gene knockout library provided a list of genes indispensable for growth at 47°C, called thermotolerant genes. Genes for which expression was affected by exposure to CHT were identified by DNA chip analysis. Unexpectedly, the former contents did not overlap with the latter except...
-
Assessment of Environmental Loads in the Life Cycle of a Retail and Service Building
PublicationIn order to achieve the European Union’s climate and energy goals, investments are required, mainly in the areas of energy efficiency, renewable energy sources and infrastructure. Buildings are responsible for almost half of total energy consumption, and nearly 80% of them are energy and ecologically inefficient. The policy of European countries is increasingly more focused on facilities with the highest potential in the areas...
-
Siedmiokryterialny miernik oceny niepotokowych procesów produkcyjnych
PublicationGrowing expectations of clients, who demand products adapted to their individual needs is inducing the development of batch processes. The author developed a model of batch processes rating based on the following criterions: • Economical criterion applies to evaluation of the productions’ cost levels connected with the process subjected to analysis and necessary investment funds. • Ecological criterion is about means of natural...
-
Determination of t8/5 cooling times for underwater local dry welding of steel
PublicationKnowledge of thermal history is the basic condition for studying the structure - properties of welded joints. The determinant of thermal history is the thermal cycle, whose in-situ measurements are still a big challenge. Water as the welding environment complicates this issue even more. The article presents a method to determine an equation for calculating t8/5 cooling times for underwater gas metal arc welding of unalloyed steels...
-
Potential Impact of Waterway Development on Cultural Landscape Values: The Case of the Lower Vistula
PublicationThe northern (“lower”) section of the Vistula is on the route of two international waterways—E70 and E40. However, the current condition of the riverbed prevents larger vessels from passing through. Plans for the waterway date back to the beginning of the 20th century. Following Poland’s ratification of the European Agreement on Main Inland Waterways of International Importance in 2017, the general concept has been transformed...
-
Compatibility of Crude Oil Blends─Processing Issues Related to Asphaltene Precipitation, Methods of Instability Prediction─A Review
PublicationProcessing crude oil of variable composition, especially due to the need to process crude oil blends obtained from various sources, presents a tremendous process challenge. This is mainly due to the destabilization of the colloidal system manifested mostly by the precipitation of the asphaltene fraction. The precipitation of asphaltenes from crude oil is a serious problem during extraction, transport, and processing. In the latter...
-
Novel Versatile Topologies and Design Optimization of Wide-Bandstop Frequency Selective Surfaces for X-Band, Ku-Band and Millimeter-Wave Applications
PublicationNovel designs of frequency selective surface (FSS) are presented for wideband applications in X, Ku and mmWave (millimeter Wave) bands. Two identical metallic layers of FSS are imprinted on both sides of the RO4003 substrate. The geometry parameters are optimized to maximize the bandstop at the specified in-band maximum transmission level of –10 dB; satisfaction of the latter condition is enforced through appropriate formulation...
-
Performance of Vector-valued Intensity Measures for Estimating Residual Drift of Steel MRFs with Viscous Dampers
PublicationViscous Dampers (VDs) are widely used as passive energy dissipation system for improving seismic performance levels especially in retrofitting of buildings. Residual Inter-story Drift Ratio (R-IDR) is another important factor that specifies the condition of building after earthquake. The values of R-IDR illustrates the possibility of retrofitting and repairing of a building. Therefore, this study aims to explore the vector-valued...
-
Expert System and Decision Support System for Electrocardiogram Interpretation and Diagnosis: Review, Challenges and Research Directions
PublicationElectrocardiography (ECG) is one of the most widely used recordings in clinical medicine. ECG deals with the recording of electrical activity that is generated by the heart through the surface of the body. The electrical activity generated by the heart is measured using electrodes that are attached to the body surface. The use of ECG in the diagnosis and management of cardiovascular disease (CVD) has been in existence for over...
-
Rapid Design of 3D Reflectarray Antennas by Inverse Surrogate Modeling and Regularization
PublicationReflectarrays (RAs) exhibit important advantages over conventional antenna arrays, especially in terms of realizing pencil-beam patterns without the employment of the feeding networks. Unfortunately, microstrip RA implementations feature narrow bandwidths, and are severely affected by losses. A considerably improved performance can be achieved for RAs involving grounded dielectric layers, which are also easy to manufacture using...