Search
Search results for: rolling resistance
-
PRZYCZEPY DO BADANIA OPORU TOCZENIA OPON DO SAMOCHODÓW OSOBOWYCH
PublicationPrzedstawiono doświadczenia Zespołu Pojazdów Katedry Konstrukcji Maszyn i Pojazdów Wydziału Mechanicznego Politechniki Gdańskiej dotyczące urządzeń badawczych (przyczep) do pomiaru oporu toczenia opon do samochodów osobowych i nawierzchni drogowych. Opisano przyczepy pomiarowe tego typu. Pomiary oporu toczenia opon samochodowych wymuszane są koniecznością osiągania przez pojazd jak największej swojej sprawności...
-
HOW EFFICIENT IS NOISE LABELING OF TIRES?
PublicationSince 2012 all new tires in Europe must be labeled. The label contains general information about tire performance concerning rolling resistance (that corresponds to fuel economy), noise emission and wet grip (only for passenger car tires). Measurements of noise performance of tires must be performed according to the Annex 3 of the Regulation No 117 of the Economic Commission for Europe of the United Nations. The regulation specifies...
-
Scientific research in the Department of Machine Design and Automotive Engineering
PublicationShort descriptions of various research subjects taken up at the Department of Machine Design and Automotive Engineering are included in the paper. The subjects cover a wide range of bearing systems and tribology research and the research on tires and road surfaces. A third field of activity is biomedical engineering – with the attempts to improve methods of modelling biological materials in FEM calculations. The Department has...
-
Układ kompensacji wpływu wzniesienia oraz przyspieszenia w przyczepie do badania oporu toczenia
PublicationW artykule przedstawiono metodę pomiaru współczynnika oporu toczenia przy wykorzystaniu przyczepy opracowanej w Zakładzie Pojazdów na Politechnice Gdańskiej. Następnie omówiono opatentowany układ bezwładnościowy do korekcji wpływu wzniesienia oraz metodę korekcji wpływu przyspieszenia wzdłużnego. W dalszej części przedstawiono przykładowe wyniki obrazujące pomiar współczynnika CRR na wzniesieniu przy zmiennej prędkości.
-
Degradation of reference tyres used for CPX measurements
PublicationMeasurements of tyre/road noise using the Close Proximity Method are based on reference tyres that are described in ISO/TS 11819-3. The standard specifies two tyres, namely "P1" and "H1" that should be used during measurements. To be used for measurements each tyre must fulfill certain conditions that are listed in the standard. The conditions are related to the tread pattern depth and rubber hardness. During experiments performed...
-
API 5L X65 steel - CMOD-force record in -10°C, along rolling direction
Open Research DataSteel designated as API 5L X65 is often used for oil and gas transportation pipelines. It is caused due to its high ductility, weldability and good corrosion resistance. API 5L X65 is a low alloy steel with carbon content less than 0.3% (depends on delivery condition). Once installed, a pipeline remains in place for many years. Throughout its life,...
-
API 5L X65 steel - CMOD-force record in -10°C, across rolling direction
Open Research DataSteel designated as API 5L X65 is often used for oil and gas transportation pipelines. It is caused due to its high ductility, weldability and good corrosion resistance. API 5L X65 is a low alloy steel with carbon content less than 0.3% (depends on delivery condition). Once installed, a pipeline remains in place for many years. Throughout its life,...
-
API 5L X65 steel - tensile properties in room temperature -10°C, along rolling direction
Open Research DataSteel designated as API 5L X65 is often used for oil and gas transportation pipelines. It is caused due to its high ductility, weldability and good corrosion resistance. API 5L X65 is a low alloy steel with carbon content less than 0.3% (depends on delivery condition). Once installed, a pipeline remains in place for many years. Throughout its life,...
-
API 5L X65 steel - tensile properties in room temperature +20°C, across rolling direction
Open Research DataSteel designated as API 5L X65 is often used for oil and gas transportation pipelines. It is caused due to its high ductility, weldability and good corrosion resistance. API 5L X65 is a low alloy steel with carbon content less than 0.3% (depends on delivery condition). Once installed, a pipeline remains in place for many years. Throughout its life,...
-
API 5L X65 steel - tensile properties in room temperature -10°C, across rolling direction
Open Research DataSteel designated as API 5L X65 is often used for oil and gas transportation pipelines. It is caused due to its high ductility, weldability and good corrosion resistance. API 5L X65 is a low alloy steel with carbon content less than 0.3% (depends on delivery condition). Once installed, a pipeline remains in place for many years. Throughout its life,...
-
API 5L X65 steel - tensile properties in room temperature +20°C, along rolling direction
Open Research DataSteel designated as API 5L X65 is often used for oil and gas transportation pipelines. It is caused due to its high ductility, weldability and good corrosion resistance. API 5L X65 is a low alloy steel with carbon content less than 0.3% (depends on delivery condition). Once installed, a pipeline remains in place for many years. Throughout its life,...
-
ROSANNE Project: New Procedure for Noise Characterisation of Road Surfaces in Europe
PublicationROSANNE is a collaborative project in the 7th EU Framework Programme which aims at harmonising measurement methods for skid resistance, noise emission and rolling resistance of road pavements as a preparation for standardization. The project started in November 2013 and is developing and improving standards in the field of working group CEN/TC 227/WG 5. Regarding the influence of the pavement on the road traffic noise emission,...
-
Initial Field Validation of Poroelastic Pavement Made with Crumb Rubber, Mineral Aggregate and Highly Polymer-Modified Bitumen
PublicationTire/road noise in most driving conditions dominates other sources of traffic noise. One of the most efficient ways of reducing tire/road noise is to use the so-called “low noise pavement”. According to numerous studies, at present, poroelastic road pavement that is composed of rubber and mineral aggregate and polyurethane or bituminous binder gives the best noise reduction up to 12 dB. Unfortunately, there are many problems with...
-
Bitumen-Based Poroelastic Pavements: Successful Improvements and Remaining Issues
PublicationThis article presents the development process of designing and testing poroelastic pavement based on highly polymer-modified bitumen. Poroelastic wearing course was composed of mineral and rubber aggregate mixed with highly polymer-modified bitumen, in contrast to previous trials, during which polyurethane resins were mainly used as binder, which led to several serious technological problems concerning difficult production, insufficient...
-
Poroelastic Road Surfaces - State of The Art
PublicationPoroelastic Road Surfaces (PERS) constitute a specific group of pavements containing a great amount of crumbled rubber. In most cases rubber aggregate constitutes about 20% of the mixture (by weight) and a polyurethane resin is used as a binder. As a result, PERS is characterized by a much higher elasticity than asphalt and a high porosity typical for drainage pavements. Due to this, tire/road noise is greatly reduced and on top...
-
Reduction of road traffic noise by source measures — present and future strategies
PublicationThe current trend worldwide is less focused on reducing road traffic noise. This is in strong contrast to the severe impact of traffic noise to the general health and quality of life. A more holistic and combined strategy is needed. Current international rules and regulations regarding vehicles and tyres are not sufficient to reduce traffic noise levels in an effective way. Calculations show that these regulations will only yield...
-
The effect of tire aging on acoustic performance of CPX reference tires
PublicationReduction of tire/road noise is one of the biggest environmental challenges of road traffic. To reduce that noise it is necessary to perform acoustic measurements on the base of wellproven standard procedures. One method of measurements that is in common use, namely the Close Proximity Method (CPX), is described in standard ISO-DIS 11819-2. As this method is used to classify road surfaces regarding their influence on vehicle noise,...
-
Straightening of ship hull structure made of 316L stainless steel - tensile test of water cooled materia
Open Research DataThe AISI 316L type steel belongs to the group of chromium-nickel stainless steels. They are determined according to European standards as X2CrNiMo17-12-2 and belong to the group of austenitic stainless steels. Steels of this group are used for elements working in seawater environments, for installations in the chemical, paper, and food, industries,...
-
Straightening of ship hull structure made of 316L stainless steel - tensile test of reference material materia (transverse direction)
Open Research DataThe AISI 316L type steel belongs to the group of chromium-nickel stainless steels. They are determined according to European standards as X2CrNiMo17-12-2 and belong to the group of austenitic stainless steels. Steels of this group are used for elements working in seawater environments, for installations in the chemical, paper, and food, industries,...
-
Straightening of ship hull structure made of 316L stainless steel - tensile test of reference material materia (longitudinal direction)
Open Research DataThe AISI 316L type steel belongs to the group of chromium-nickel stainless steels. They are determined according to European standards as X2CrNiMo17-12-2 and belong to the group of austenitic stainless steels. Steels of this group are used for elements working in seawater environments, for installations in the chemical, paper, and food, industries,...
-
Straightening of ship hull structure made of 316L stainless steel - microstructure of naturally colled material
Open Research DataThe AISI 316L type steel belongs to the group of chromium-nickel stainless steels. They are determined according to European standards as X2CrNiMo17-12-2 and belong to the group of austenitic stainless steels. Steels of this group are used for elements working in seawater environments, for installations in the chemical, paper, and food, industries,...
-
Straightening of ship hull structure made of 316L stainless steel - microstructure of water cooled material
Open Research DataThe AISI 316L type steel belongs to the group of chromium-nickel stainless steels. They are determined according to European standards as X2CrNiMo17-12-2 and belong to the group of austenitic stainless steels. Steels of this group are used for elements working in seawater environments, for installations in the chemical, paper, and food, industries,...
-
Straightening of ship hull structure made of 316L stainless steel - microstructure of reference material
Open Research DataThe AISI 316L type steel belongs to the group of chromium-nickel stainless steels. They are determined according to European standards as X2CrNiMo17-12-2 and belong to the group of austenitic stainless steels. Steels of this group are used for elements working in seawater environments, for installations in the chemical, paper, and food, industries,...
-
Straightening of ship hull structure made of 316L stainless steel - tensile test of naturally cooled material
Open Research DataThe AISI 316L type steel belongs to the group of chromium-nickel stainless steels. They are determined according to European standards as X2CrNiMo17-12-2 and belong to the group of austenitic stainless steels. Steels of this group are used for elements working in seawater environments, for installations in the chemical, paper, and food, industries,...
-
Tyre/road noise measurements on ISO tracks according to the UNECE Regulation 117
PublicationWithin the Polish-Norwegian research project ELANORE, a limited Round Robin Test has been performed on 3 ISO tracks in Northern Europe. The basic objective of the project is to improve the EU directive on labelling of tyres for noise and rolling resistance, and this directive is based on the measurement procedures defined in the UN ECE Reg.117. The same test car, test tyres and measurement equipment as well as personnel were used...
-
Representativity of ISO test track surface based on controlled pass-by measurements
PublicationWithin the Polish-Norwegian research project ELANORE, a limited Round Robin Test has been performed on four ISO tracks in Northern Europe. The basic objective of the project is to improve the EU directive on labelling of tyres for noise and rolling resistance. This directive is based on the measurement procedures proscribed in the UNECE Reg.117. Measurements on 3 ISO tracks were performed in 2021 and presented at InterNoise 2022....
-
Noise Generated by Tyres Designet for Electric Vehicles - Results of Laboratory Experiments
PublicationA few years ago, electric and hybrid vehicles were rarely seen on public roads and were considered more as exotic curiosities or even as a sign of extravagance than a practical means of transport. Nowadays the situation has changes significantly. This was caused both by the technical development and legislative actions, as well as the organizational nature promoting the purchace and use of low emission vehicles. Electric vehicles...
-
Tyre/road noise reduction by a poroelastic road surface
PublicationLow noise road surfaces of existing types may in favourable cases and in new conditions provide up to 7 dB of noise reduction. For higher noise reductions, innovative solutions must be sought. Poroelastic road surfaces (PERS) may be such a solution, which currently is studied in the EU project PERSUADE. This paper presents results of trials with a PERS version prefabricated by one of the project partners. Tests were made in a laboratory...
-
Comparative 3D DEM simulations of sand–structure interfaces with similarly shaped clumps versus spheres with contact moments.
PublicationThree-dimensional simulations of a monotonic quasi-static interface behaviour between initially dense cohesionless sand and a rigid wall of different roughness during tests in a parallelly guided direct shear test under constant normal stress are presented. Numerical modelling was carried out by the discrete element method (DEM) using clumps in the form of convex non-symmetric irregularly shaped grains. The clumps had an aspect...
-
On ship roll resonance frequency
PublicationThe paper deals with the problem of modeling of rolling motion under a variety of excitation parameters. Special emphasis is put on the analysis and prediction of the frequency of the resonant mode of rolling, since it is often an essential issue in terms of motion of a ship related to her safety against capsizing or excessive amplitudes of roll. The research is performed for both free rolling and excited rolling and it is based...
-
METHOD FOR SHIP'S ROLLING PERIOD PREDICTION WITH REGARD TO NON-LINEARITY OF GZ CURVE
PublicationThe paper deals with the problem of prediction of the rolling period. A special emphasis is put on the practical application of the new method for rolling period prediction with regard to non-linearity of the GZ curve. The one degree-of-freedom rolling equation is applied with using the non-linear stiffness moment and linear damping moment formulas. A number of ships are considered to research the discrepancies between the pending...
-
Voltage fluctuations on the main switchgear of the industrial power system supplying the rolling mill motors
Open Research DataThe dataset presents the voltage waveforms on the bus bars of the main switchgear of the industrial power network for the supply of rolling mills. The data was recorded during an experiment whose purpose was to determine a level of short-term and long-term flicker caused by voltage fluctuations. In the virtual application of flickermeter, a hardware...
-
Voltage fluctuations on the main switchgear of the industrial power system supplying the rolling mill motors_part_2
Open Research DataThe dataset presents the voltage waveforms on the bus bars of the main switchgear of the industrial power network for the supply of rolling mills. The data was recorded during an experiment whose purpose was to determine a level of short-term and long-term flicker caused by voltage fluctuations. In the virtual application of flickermeter, a hardware...
-
A shear stress micromodel of urinary tract infection by the Escherichia coli producing Dr adhesin
PublicationIn this study, we established a dynamic micromodel of urinary tract infection to analyze the impact of UT-segment-specific urinary outflow on the persistence of E. coli colonization. We found that the adherence of Dr+ E. coli to bladder T24 transitional cells and type IV collagen is maximal at lowest shear stress and is reduced by any increase in flow velocity. The analyzed adherence was effective in the whole spectrum of physiological...
-
A Quantitative Investigation of Dislocation Density in an Al Matrix Composite Produced by a Combination of Micro-/Macro-Rolling
PublicationAn aluminum matrix composite with dispersed carbon nanotubes (CNTs) was produced via flake powder metallurgy using a micro-rolling process and vacuum hot pressing (VHP), followed by conventional rolling using a macro-rolling process. The microstructure and mechanical properties of the produced composites were studied. In addition, a new quantitative model was introduced to study the dislocation density based on the microstructural...
-
Hertzian Crack Propagation in Ceramic Rolling Elements
PublicationThe properties of ceramics are of most interest to rolling element manufacturers. The influence of ring crack size on rolling contact fatigue failure has been studied using numerical fracture analysis. Such crack are very often found on ceramic bearing balls and decrease fatigue life rapidly. The numerical calculations are based on a three dimensional model for the ring crack propagation. The stress intensity factors along crack...
-
Experimental research of the effect of face milling strategy on the flatness deviations
PublicationIn this paper the dependencies between face milling strategy of EN AW6082-T6 aluminum alloy samples, with difference thicknesses (6, 8, and 12 mm) and two cold rolling directions, and flatness deviations were presented. Three strategies of milling included different proportions of material removed from both sides of the plates. This approach allowed to control the proportions of residual surface stresses on both sides of the specimens,...
-
Tribological performance of PTFE-metal binary coatings in rolling/sliding contact
PublicationTribological performance of surface coatings with embedded PTFE reservoirs in rolling/sliding contact is reported. Using two different coating materials and two shapes and patterns of PTFE reservoirs test samples in the form of discs were prepared and tested in a four-ball contact configuration under loads corresponding to nominal contact pressure of 0.5 and 1.0 GPa. It was found that one coating, namely aluminium-bronze with embedded...
-
The instantaneous flicker sensation level measured in the industrial power system supplying the rolling mill motors
Open Research DataThe dataset presents the instantaneous flicker sensation level measured on the bus bars of the main switchgear of the industrial power network for the supply of rolling mills. The data were obtained during an experiment whose purpose was to determine a level of short-term and long-term flicker caused by voltage fluctuations. In the virtual application...
-
DYNAMIC ANALYSIS OF HISTORIC RAILWAY BRIDGES IN POLAND IN THE CONTEXT OF ADJUSTING THEM TO PENDOLINO TRAINS
PublicationThe article presents the dynamic analysis of the historic railway bridge in Tczew as an example of the usefulness of such type of bridge for high-speed trains. The model of the bridge and the simulation of rolling stock passage was performed in SOFISTIK program. The scope of work includes experimental studies, the solution of the problem concerning the correct solution features dynamic model takes into account the dependencies...
-
Analysis of Ceramic Elements with Ring-Crack Defects in Lubricated Rolling Contact
PublicationThe properties of ceramics, specifically low density, high hardness, high temperature capability and low coefficient of thermal expansion are of most interest to rolling element manufacturers. Surface ring cracks on lubricating rolling contact fatigue failure has been studied using numerical fracture analysis. Such cracks are very often found on ceramic bearing balls and decrease fatigue life rapidly. The numerical calculations...
-
Numerical analysis of crack propagation in silicone nitride
PublicationThe properties of ceramics, specifically low density, high hardness, high temperature capability and low coefficient of thermal expansion are of most interest to rolling element manufacturers. The influence of ring crack size on rolling contact fatigue failure has been studied using numerical fracture analysis. Such cracks are very often found on ceramic bearing balls and decrease fatigue life rapidly. The numerical calculation...
-
The dynamic performance analysis of the Micro-turbine's rotor supparted on slide and roling element bearings
PublicationThis article presents the results of investigations of dynamic characteristics of a small-dimension rotor with slide and rolling element bearings. The object of investigations was the rotor-bearing system designed for the ORC based low-power steam micro-turbine. The investigations were performed using MESWIR series programs, as well as commercial FEA software ABAQUS and MADYN 2000. The results of modal analysis of the micro-rotor...
-
Elastic waves in the railroad track substructures and its surroundings analyzed with non-classical operational methods
PublicationWe analyze the propagation of the waves generated by the rolling stock and the interaction of those waves on the medium and its surroundings. We use non-classical operational methods for monitoring construction of the railway infrastructure and for noise damping.
-
Surface Roughness Evaluation in Thin EN AW-6086-T6 Alloy Plates after Face Milling Process with Different Strategies
PublicationLightweight alloys made from aluminium are used to manufacture cars, trains and planes. The main parts most often manufactured from thin sheets requiring the use of milling in the manufacturing process are front panels for control systems, housing parts for electrical and electronic components. As a result of the final phase of the manufacturing process, cold rolling, residual stresses remain in the surface layers, which can influence...
-
The effect of depth of surface layers constituted by vacuum technologies on pitting
PublicationThe paper presents the results of a study of the effect of vacuum technologies of formation of surface layers on pitting of associated elements in a lubricated, heavy-load rolling contact. The study has shown that increase in a PVD coat depth is accompanied by decrease in the fatigue friction pair.
-
Przegląd układów hydraulicznych do otwierania i zamykania pokryw lukowych. Część II
PublicationOpisano konstrukcję i budowę pokryw lukowych przesuwnych typu rolling, piggy-back (''na barana''). Zamieszczono schematy hydrauliczne oraz opisano działanie mechanizmów do ryglowania, do niskiego i wysokiego podnoszenia oraz przesuwania pokryw.
-
Evaluation of electrical parameters of traction supply system for complex railway traffic conditions, using simulation methods
PublicationDevelopment of electrified transport systems, railways modernization, expansion of urban transport networks, purchases of modern rolling stock causes that updating of electric traction supply system is necessary. This chapter presents an effective method for electrical parameters of traction supply system evaluation, using simulation methods.
-
Novel Fault Identification for Electromechanical Systems via Spectral Technique and Electrical Data Processing
PublicationIt is proposed, developed, investigated, and validated by experiments and modelling for the first time in worldwide terms new data processing technologies, higher order spectral multiple correlation technologies for fault identification for electromechanical systems via electrical data processing. Investigation of the higher order spectral triple correlation technology via modelling has shown that the proposed data processing technology...
-
Crack propoagation in MgO-PSZ ceramic materials
PublicationThe properties of ceramic materials such as elevated hardness, high temperature capability, low coefficient of thermal expansion are of interest for rolling element materials. Widely used ceramic materials in engineering applications are silicon nitride, zirconia and alumina. The paper presents an experimental study of the fatigue life of MgO-PSZ ceramic material in lubricated contact with defined types of cracks. A ceramic angular...