Search
Filters
total: 104
filtered: 95
Search results for: CONCRETE BEAMS
-
Partially prestressed concrete beams with bonded and unbonded strands
PublicationThis article relate the tests of partially prestressed concrete beams. There is presented the research programme - geometry of elements, method of loading, the materials and variables. There have been shown preliminary test results of prestressed concrete elements with bonded and unbonded strands, and compared to the test results of R.C. beam.
-
Experimental investigations on concrete beams reinforced with CFRP lamellas
PublicationPaper presents experimental investigation made on two concrete beams reinforced with internal Carbon Fibre Reinforced Polymer (CFRP) lamellas (i.e. strips, bands). The reinforcement geometrical arrangement was similar as in normal concrete beams reinforced with steel bars and stirrups. The beams were destroyed by the shear forces, as intended. Obtained load-carrying capacities were lower as expected: below 40% of a calculated value....
-
3D DEM simulations of fracture in reinforced concrete beams
PublicationArtykuł dotyczy zachowania się belki żelbetowej bez zbrojenia pionowego przy trzypunktowym zginaniu. Belka uległa zniszczeniu wskutek ścinania z powodu obecności nadmiernego zbrojenia podłużnego. Eksperymenty przeprowadzono w skali laboratoryjnej z wykorzystaniem systemu mikro-CT, a następnie odtworzono je w analizach numerycznych stosując metodą elementów dyskretnych 3D (DEM). Zastosowano 4-fazowy model betonu z mezostrukturą,...
-
Debonding Detection in Reinforced Concrete Beams with the Use of Guided Wave Propagation
PublicationOne of the most frequent damage of the reinforced concrete structures is debonding between steel bar and concrete cover. In the case of debonding occurrence not only the strength of the structure decreases, but also it is more vulnerable to corrosion damages. For this reason fast and effective methods of debonding detection in an early stage of its development need a significant boost. The paper presents analytical and experimental...
-
Structural Assessment of Reinforced Concrete Beams Incorporating Waste Plastic Straws
PublicationThe behavior of reinforced concrete beams containing fibers made of waste plastic straws (WPSs) under the three point bending test is examined. The effect of WPS fiber addition on the compressive and split tensile strength is reported. Four concrete mixes were prepared. The control mix PS-0 had a proportion of 1 cement: 1 sand: 2 coarse aggregate and a water cement ratio of 0.4. In the other three mixes PS-0.5, PS-1.5 and PS-3,...
-
RMS-based damage detection in reinforced concrete beams: numerical simulations
PublicationImage-based damage detection methods using guided waves are well known and widely applied approaches in structural diagnostics. They are usually utilized in detection of surface damages or defects of plate-like structures. The article presents results of the study of applicability of imaging wave-based methods in detection in miniscule internal damage in the form of debonding. The investigations were carried out on numerical models...
-
BEHAVIOR OF REINFORCED CONCRETE BEAMS CONTAINING LIGHTWEIGHT AGGREGATE IN THE TENSILE ZONE
Publication.
-
Multi-scale modelling of concrete beams subjected to three-point bending
PublicationW artykule przedstawiono wyniki numeryczne MES dwuskalowego modelowania belek betonowych z nacięciem na poziomie skali makro i mezo. Obliczenia wykonano przy wykorzystaniu modelu degradacji sztywności z nielokalnym osłabieniem. Beton został opisany na poziomie skali mezo jako stochastyczny materiał 3-składnikowy złożony z kruszywa, zaczynu cementowego oraz stref kontaktu. Natomiast na poziomie skali makro został opisany jako materiał...
-
Experimental investigations of size effect in reinforced concrete beams failing by shear
PublicationW artykule omówiono wyniki doświadczalne efektu skali w zbrojonych betonowych belkach niszczących się przez ścinanie. Doświadczenia wykonano dla belek o różnych wymiarach ze zbrojeniem stalowym i bazaltowym. Podczas doświadczeń pomierzono siłę oraz szerokości lokalizacji i rys. Wyniki porównano z modelem skali wg Bazanta.
-
Evaluation of the resistance of steel–concrete adhesive connection in reinforced concrete beams using guided wave propagation
PublicationThe development of the nondestructive diagnostic methods is of significant importance in the last decades. A special attention is paid to diagnostics of reinforced concrete structures, which are very popular in the civil engineering field. A possible use of the guided waves in the estimation of the resistance of steel–concrete adhesive connection is studied in the following paper. The relationships relating adhesive connection...
-
The method of analysis of damage reinforced concrete beams using terrestial laser scanning
PublicationThe authors present an analysis of the possibility to assess deformations and mechanisms of destructing bent reinforced concrete beams using the terrestrial laser scanning. As part of the experiments carried out at the Regional Laboratory of Construction of the Concrete Structures Division of the Civil and Environmental Engineering Faculty at Gdansk University of Technology, the reinforced concrete beams were subjected to destruction...
-
SIMULATIONS OF FRACTURE IN CONCRETE BEAMS UNDER BENDING USING A CONTINUUM AND DISCRETE APPROACH
PublicationThe paper describes two-dimensional meso-scale results of fracture in notched concrete beams under bending. Concrete was modelled as a random heterogeneous 4-phase material composed of aggregate particles, cement matrix, interfacial transitional zones and air voids. Within continuum mechanics, the simulations were carried out with the finite element method based on a isotropic damage constitutive model enhanced by a characteristic...
-
THE METHOD OF ANALYSIS OF DAMAGE REINFORCED CONCRETE BEAMS USING TERRESTRIAL LASER SCANNING
PublicationThe authors present an analysis of the possibility to assess deformations and mode of failure of R-C beams using terrestrial laser scanning. As part of experiments carried out at the Regional Laboratory of Construction (at Gdansk University of Technology), reinforced concrete beams were subjected to destruction by bending and by shear. The process of press impact on the reinforced concrete beam was recorded using terrestrial laser...
-
Measurements and calculations of the width of the fracture process zones on the surface of notched concrete beams
PublicationArtykuł omawia wyniki pomiaru i analizy numerycznej szerokości strefy pękania w belkach betonowych z nacięciem. Do pomiarów zastosowano metodę DIC. Do symulacji zastosowano model sprężysto - plastyczny i model z degradacją sztywności. Oba modele zostały rozszerzone o nielokalne osłabienie. Wyniki symulacji porównano z doświadczeniami.
-
Application of twin-plane ECT sensor for identification of the internal imperfections inside concrete beams
PublicationThe main purpose of this paper is to investigate application of special construction of Electrical Capacitance Tomography (ECT) sensor to concrete beams internal homogeneity tests. Identification of internal imperfection inside the concrete beams is one of the main problems related to analysis of the construction structure bearing capacity. Therefore, this paper shows attempts to study the measurement prospects for this non-invasive,...
-
Debonding Size Estimation in Reinforced Concrete Beams Using Guided Wave-Based Method
PublicationThe following paper presents the results of the theoretical and experimental analysis of the influence of debonding size on guided wave propagation in reinforced concrete beams. The main aim of the paper is a development of a novel, baseline-free method for determining the total area of debonding between steel rebar embedded in a concrete cover on the basis of the average wave velocity or the time of flight. The correctness of...
-
Verification of Selected Calculation Methods Regarding Shear Strength in Reinforced and Prestressed Concrete Beams
PublicationThe purpose of this article was an attempt to compare selected calculation methods regarding shear strength in reinforced and prestressed concrete beams. Several calculation methods were tested. This included codes: PN-EN 1992-1-1:2008 [1], ACI 318- 14 [2] and fib Model Code for Concrete Structures 2010 [3]. The analysis also consists of methods published in technical literature. Calculations of shear strengths were made based...
-
Coda wave interferometry in monitoring the fracture process of concrete beams under bending test
PublicationEarly detection of damage is necessary for the safe and reliable use of civil engineering structures made of concrete. Recently, the identification of micro-cracks in concrete has become an area of growing interest, especially using wave-based techniques. In this paper, a non-destructive testing approach for the characterization of the fracture process was presented. Experimental tests were made on concrete beams subjected to mechanical...
-
Fatigue Performance of Double-Layered Asphalt Concrete Beams Reinforced with New Type of Geocomposites
PublicationThe reinforcement of asphalt layers with geosynthetics has been used for several decades, but proper evaluation of the influence of these materials on pavement fatigue life is still a challenging task. The presented study investigates a novel approach to the reinforcement of asphalt layers using a new type of geogrid composite, in which square or hexagonal polypropylene stiff monolithic paving grid with integral junctions is bonded...
-
Laboratory fatigue assessment of large geocomposite-reinforced double-layered asphalt concrete beams
PublicationGeosynthetic reinforcement of asphalt layers has been used for several decades. Evaluation of the influence of these materials on pavement fatigue life is still ongoing, especially for new types of geocomposites. This paper presents the evaluation of fatigue performance of large asphalt concrete beams reinforced with a new type of composite in which square or hexagonal polypropylene stiff monolithic paving grid with integral junctions...
-
Laboratory fatigue assessment of large geocomposite-reinforced double-layered asphalt concrete beams
PublicationGeosynthetic reinforcement of asphalt layers has been used for several decades. Evaluation of the influence of these materials on pavement fatigue life is still ongoing, especially for new types of geocomposites. This paper presents the evaluation of fatigue performance of large asphalt concrete beams reinforced with a new type of composite in which square or hexagonal polypropylene stiff monolithic paving grid with integral junctions...
-
Numerical studies on size effects in concrete beams. Architecture Civil Engineering Environment ACEE
PublicationW artykule przedstawiony wyniki obliczeń efektów skali w belkach betonowych podczas zginania. Zastosowano model sprężysto-plastyczny z nielokalnym osłabieniem. Rozkład wytrzymałości na rozciąganie był stochastyczny - przestrzennie skorelowany. Belki były geometrycznie podobne. Wyniki porównano z modelem efektu skali Bazanta.
-
Numerical investigations of size effects in notched and un-notched concrete beams under bending
PublicationW artykule przedstawiono wyniki numerycznej analizy efektów skali (efektu deterministycznego i stochastycznego) w belkach betonowych z nacięciem i bez nacięcia poddanych zginaniu z uwzględnieniem lokalizacji odkształceń. Obliczenia wykonano przy zastosowaniu metody elementów skończonych i sprężysto-plastycznego modelu z nielokalnym osłabieniem. Pokazano wpływ wielkości belek betonowych na ich nośność oraz rozkład lokalizacji odkształceń.
-
Experimental and numerical investigations of size effects in reinforced concrete beams with steel or basalt bars.
PublicationW artykule przedstawiono wyniki obliczeń efektów skali w belkach betonowych zbrojonych prętami stalowymi i bazaltowymi podczas zginania. Zastosowano model sprężysto-plastyczny z nielokalnym osłabieniem. Rozkład wytrzymałości na rozciąganie był stochastyczny – przestrzennie skorelowany. Belki były geometrycznie podobne. Wyniki porównano z modelem efektu skali Bazanta
-
Experimental tests of reinforced concrete deep-beams
PublicationThe paper presents results of experimental research of the reinforced concrete deep beam with a spatial arrangement. Tested structural elements consist of the cantilever deep beam loaded on the height and transverse deep beam with hanging on it another one. The analysis includes crack morphology, effort of steel and load distribution. The article verified effectiveness of two different kind of reinforcement in both tested deep...
-
Reference-free determination of debonding length in reinforced concrete beams using guided wave propagation
PublicationThis paper presents theoretical and experimental investigations of guided wave propagation in reinforced concrete beams, with pre-existing debonding between steel rebars and concrete blocks, for the purpose of damage detection. The primary aim of these investigations was a detailed analysis of the possible applications of wave propagation in single and multiple debonding detection in reinforced concrete structures and reference-free...
-
Size effect in concrete beams under bending – influence of the boundary layer and the numerical description of cracks
PublicationIn the paper the size effect phenomenon in concrete is analysed. The results of numerical simulations of using FEM on geometrically similar un-notched and notched concrete beams under bending are presented. Concrete beams of four different sizes and five different notch heights under three-point bending test were simulated. In total 18 beams were analysed. Two approaches were used to describe cracks in concrete. First, eXtended...
-
Experimental Investigations of Fracture Process Using DIC in Plain and Reinforced Concrete Beams under Bending
PublicationThe fracture behaviour of concrete and reinforced concrete beams under quasi-static three-point bending was comprehensively investigated with experiments at laboratory scale. The eight various concrete mixes were tested. The influence of the shape, volume and size of aggregate particles and reinforcement on concrete fracture under bending was studied. Displacements on the surface of concrete beams were measured by means of the...
-
The vibration-based assessment of the influence of elevated temperature on the condition of concrete beams with pultruded GFRP reinforcement
PublicationConcrete beams reinforced with glass fiber reinforced polymer (GFRP) bars subjected to elevated temperature have been experimentally studied. The influence of high temperatures on GFRP-reinforced concrete beams condition has been check both, destructively and nondestructively. The nondestructive tests foresaw vibration-based tests to obtain the natural frequency values after exposure to varying temperatures. The vibration-based...
-
Two - scale model for concrete beams subjected to three point bending - numerical analyses and experiments
PublicationArtykuł omawia dwu-skalowe podejście do betonu przy wykorzystaniu połączonych modeli. Metodę elementów skończonych zastosowano na poziomie makro. Na poziomie mikro zastosowano metodę elementów dyskretnych. Macierz sztywności wyznaczono na podstawie tensora naprężeń wyznaczonego w skali mikro. Wyniki numeryczne dw-skalowe porównano z wynikami dyskretnymi dla całego obszaru.
-
Experimental and numerical assessment of size effect in geometrically similar slender concrete beams with basalt reinforcement
PublicationW artykule przedstawiono doświadczalne i numeryczne wyniki badań efektu skali w geometrycznie podobnych smukłych belkach betonowych ze zbrojeniem bazaltowym. Doświadczenia zostały symulowane stosując metodę elementów skończonych w oparciu o model sprężysto-plastyczny z degradacją sztywności i nielokalnym osłabieniem. Otrzymano dobrą zgodność wyników doświadczalnych z numerycznymi.
-
FE-investigations on crack spacing in reinforced concrete beams within non-local continuum mechanics.
PublicationW artykule przedstawiono wyniki numerycznej analizy rozstawu rys w belkach żelbetowych przy zastosowaniu dwóch ciągłych modeli nielokalnych. Zbadano wpływ wielu różnych parametrów na rozstaw rys.
-
Investigations on fracture in reinforced concrete beams in 3-point bending using continuous micro-CT scanning
PublicationThis study explores a fracture process in rectangular reinforced concrete (RC) beams subjected to quasi-static three-point bending. RC beams were short and long with included longitudinal reinforcement in the form of a steel or basalt bar. The ratio of the shear span to the effective depth was 1.5 and 0.75. The focus was on the load–deflection diagram and crack formation. Three-dimensional (3D) analyses of the size and distribution...
-
Detection of debonding in reinforced concrete beams using ultrasonic transmission tomography and hybrid ray tracing technique
PublicationThis paper concerns inspection of reinforced concrete elements, with particular emphasis on assessing the quality of the adhesive connection between steel and concrete. A novel theoretical model was developed to determine the paths of transmitted, refracted and reflected elastic waves as well as a creeping wave propagated along the inclusion surface. Imaging the internal structure of tested beams was based on wave propagation measurements...
-
Chained machine learning model for predicting load capacity and ductility of steel fiber–reinforced concrete beams
PublicationOne of the main issues associated with steel fiber–reinforced concrete (SFRC) beams is the ability to anticipate their flexural response. With a comprehensive grid search, several stacked models (i.e., chained, parallel) consisting of various machine learning (ML) algorithms and artificial neural networks (ANNs) were developed to predict the flexural response of SFRC beams. The flexural performance of SFRC beams under bending was...
-
Non-Destructive Diagnostics of Concrete Beams Strengthened with Steel Plates Using Modal Analysis and Wavelet Transform
PublicationExternally bonded reinforcements are commonly and widely used in civil engineering objects made of concrete to increase the structure load capacity or to minimize the negative effects of long-term operation and possible defects. The quality of adhesive bonding between a strengthened structure and steel or composite elements is essential for effective reinforcement; therefore, there is a need for non-destructive diagnostics of adhesive...
-
Modelling reinforced concrete beams under mixed shear-tension failure with different continuous FE approaches
PublicationThe paper presents quasi-static numerical simulations of the behaviour of short reinforced concrete beams without shear reinforcement under mixed shear-tension failure using the FEM and four various constitutive continuum models for concrete. First, an isotropic elasto-plastic model with a Drucker-Prager criterion defined in compression and with a Rankine criterion defined in tension was used. Next, an anisotropic smeared crack...
-
FE analysis of a coupled energetic-statistical size effect in plain concrete beams with varying material properties.
PublicationThe numerical FE investigations of a coupled energetic-statistical size effect in unnotched concrete beams of similar geometry under quasi-static three point bending were performed within elasto-plasticity with non-local softening. The stochastic FE analyses were carried out with three different beam sizes. Deterministic calculations were performed with the uniform distribution of a uniaxial tensile strength. In statistical calculations...
-
Parametric FE studies on a coupled energetic-statistical size effect in plain concrete beams under bending
PublicationW artykule omówiono wyniki połączonego deterministyczno-statystycznego efektu skali w betonowych belkach podczas zginania. Obliczenia wykonano stosując MES w zakresie sprężysto-plastyczności z nielokalnym osłabieniem. Obliczenia wykonano dla różnych długości korelacji i współczynnika zmienności.
-
Calculations of fracture process zones on meso-scale in notched concrete beams subjected to three-point bending.
PublicationW artykule przedstawiono wyniki numeryczne MES modelowanie belek betonowych z nacięciem na poziomie skali mezo. Beton został opisany na poziomie skali mezo jako stochastyczny materiał 3-składnikowy złożony z kruszywa, zaczynu cementowego oraz stref kontaktu. Obliczenia wykonano przy wykorzystaniu modelu degradacji sztywności z nielokalnym osłabieniem. Zbadano wpływ stochastycznego rozkładu kruszywa, średnicy, kształtu oraz zagęszczenia...
-
Modelling of reinforced concrete beams under mixed shear-tension failure with different continuous FE approaches
PublicationW artykule omówiono wyniki modelowania numerycznego MES zachowania się wysokich belek żelbetowych podczas zniszczenia mieszanego ścinanie-rozciąganie. Obliczenia wykonano stosując różne modele dla betonu rozszerzone o długość charakterystyczną mikrostruktury w oparciu o teorie nielokalna. Otrzymano dobrą zgodność z wynikami doświadczalnymi.
-
FE investigations of the effect of fluctuating local tensile strength on coupled energetic-statistical size effect in concrete beams
PublicationThe effect of fluctuating local tensile strength on a coupled energetic-statistical size effect in plain concrete beams under bending was numerically investigated. First, the influence of varying autocorrelation length of the random field describing a spatial variation of local tensile strength was studied. Next, the influence of the coefficient of variation of local tensile strength was analyzed. The numerical FE investigations...
-
Concrete beams under bending - calculations of size effects within stochastic elasto-plasticity with non-local softening
PublicationW artykule przedstawiono wyniki numerycznej analizy efektów skali (efektu deterministycznego i stochastycznego) w belkach betonowych nacięciem poddanych zginaniu z uwzględnieniem lokalizacji odkształceń. Obliczenia wykonano przy zastosowaniu metody elementów skończonych i sprężysto-plastycznego modelu z nielokalnym osłabieniem. Pokazano wpływ wielkości belek betonowych na nośność.
-
Ultrasonic diagnostics of concrete T-beams used in bridge structures
PublicationThis paper describes a method of ultrasonic diagnostics used for prefabricated concrete elements. The studies are focused on the applicability of nondestructive techniques based on impulse and wave packet induced elastic waves for the condition assessment of T-shaped bridge beams. Experimental tests were performed for the prestressed beam used for the superstructure of the viaduct on A1 highway near Toruń. In addition numerical...
-
Simulations of spacing of localized zones in reinforced concrete beams using elasto-plasticity and damage mechanics with non-local softening
Publication -
Notched concrete beams under bending - calculations of size effects within stochastic elasto-plasticity with non-local softening
PublicationW artykule przedstawiono wyniki numerycznej analizy efektów skali (efektu deterministycznego i stochastycznego) w belkach betonowych nacięciem poddanych zginaniu z uwzględnieniem lokalizacji odkształceń. Obliczenia wykonano przy zastosowaniu metody elementów skończonych i sprężysto-plastycznego modelu z nielokalnym osłabieniem. Pokazano wpływ wielkości belek na nośność z uwzględnieniem stochastycznego rozkładu wytrzymałości na...
-
Simulations of spacing of localized zones in reinforced concrete beams using elastic-plasticity and damage mechanics with non-local softening
PublicationArtykuł omawia obliczanie belek żelbetowych z uwzględnieniem lokalizacji odkształceń. Obliczenia wykonano przy zastosowaniu MES na bazie sprężysto-plastycznego prawa konstytutywnego i modelu zniszczeniowego uwzględniającego degradację sztywności rozszerzonego o długość charakterystyczną mikrostruktury za pomocą teorii nielokalnej.
-
Experimental Verification of Natural Vibration Models of Steel-concrete Composite Beams
Publication -
Vibration of Steel–Concrete Composite Beams Using the Timoshenko Beam Model
Publication -
Detection and Imaging of Debonding in Adhesive Joints of Concrete Beams Strengthened with Steel Plates Using Guided Waves and Weighted Root Mean Square
PublicationStrengthening of engineering structures is an important issue, especially for elements subjected to variable loads. In the case of concrete beams or slabs, one of the most popular approaches assumes mounting an external reinforcement in the form of steel or composite elements by structural adhesives. A significant disadvantage of adhesive joints is the lack of access to the adhesive film for visual condition assessment, thus, there...