Filters
total: 2102
filtered: 1626
-
Catalog
- Publications 1626 available results
- Journals 85 available results
- Conferences 2 available results
- People 47 available results
- Inventions 1 available results
- Projects 4 available results
- Laboratories 2 available results
- Research Teams 1 available results
- e-Learning Courses 64 available results
- Events 7 available results
- Open Research Data 263 available results
Chosen catalog filters
displaying 1000 best results Help
Search results for: SPACE TRIBOLOGY
-
Analiza przepływu oleju przez rowek smarowy wzdłużnego łożyska ślizgowego = Analysis of the lubricant flow through the hydrodynamic thrust bearings groove
PublicationSmarowanie zanurzeniowe jest tradycyjnym sposobem smarowania wzdłużnych łożysk ślizgowych. Jednak rozwiązanie to wykazuje umiarkowaną skuteczność w zapewnieniu optymalnie niskich temperatur w filmie smarowym a ponadto jest przyczyną strat mocy związanych z mieszaniem oleju w obudowie łożyska, co jest szczególnie widoczne w łożyskach szybkoobrotowych. Wymagania stawiane nowym konstrukcjom łożysk ślizgowych to zwiększanie nośności...
-
Analiza przepływu oleju przez rowek smarowy wzdłużnego łożyska ślizgowego z wykorzystaniem komputerowej dynamiki płynów (CFD) = Analysis of the lubricant flow through the hydrodynamic thrust bearings groove with the use of computational fluid dynamic
PublicationSmarowanie zanurzeniowe jest tradycyjnym sposobem smarowania wzdłużnych łożysk ślizgowych. Jednak rozwiązanie to wykazuje umiarkowaną skuteczność w zapewnieniu optymalnie niskich temperatur w filmie smarowym a ponadto jest przyczyną strat mocy związanych z mieszaniem oleju w obudowie łożyska, co jest szczególnie widoczne w łożyskach szybkoobrotowych. Obecnie wymagania stawiane nowym konstrukcjom łożysk ślizgowych to zwiększanie...
-
Klocki samopompujące w łożyskach hydrodynamicznych = Self-pumping pads in the hydrodynamic bearings
PublicationWe współpracy z firmą ALSTOM HYDRO (Szwajcaria), zespół Katedry Konstrukcji i Eksploatacji Maszyn Politechniki Gdańskiej przeprowadził symulacje przepływowe kilku rozwiązań konstrukcyjnych mających na celu zwiększenie niezawodności turbin wodnych. W artykule opisano jedno z takich rozwiązań - tak zwane łożysko z klockami samopompującymi. Głównym celem jest uzyskanie przepływu oleju w układzie smarowania łożyska hydrodynamicznego...
-
Powłoki fluoropolimerowe oraz przeciwzatarciowe w łożyskach foliowych smarowanych wodą = Fluoropolymer and anti-friction coatings for water-lubricated foil bearings
PublicationW artykule przedstawiono krótką charakterystykę oraz wyniki badań tribologicznych wybranych powłok fluoropolimerowych oraz przeciwzatarciowych. Badania zużycia powłok przeprowadzono pod kątem zastosowania w oryginalnym łożysku foliowym smarowanym wodą. Na podstawie analizy wyników wyłoniono trzy powłoki do potencjalnego zastosowania w łożyskach foliowych smarowanych wodą.
-
Analiza możliwości wpływania na pracę promieniowego uszczelnienia ślizgowego poprzez deformowanie jego panwi = Analysis of possibility of influence on the radial sliding seals operating by deformation of the bearing sleeve
PublicationW referacie przedstawiono zasadę działania promieniowych uszczelnień ślizgowych oraz ukazano istotny wpływ podstawowych parametrów konstrukcyjnych na skuteczność i jakość ich pracy. Uszczelnienia te stosowane są w instalacjach okrętowych śrub nastawnych, w turbinach wodnych typu Kaplana i maszynach górniczych do drążenia tuneli. Umożliwiają one wprowadzenie oleju pod ciśnieniem do wnętrza obracającego się wału. Zapewnienie stabilnej...
-
Ekologiczne łożysko foliowe smarowane wodą - budowa i analiza wpływu wybranych parametrów konstrukcyjnych na sztywność podparcia łożyska = Environmentaly friendly water lubricated foil braing-design and influence analysis of selected design parameters bearing support stiffness
PublicationW artykule opisano budowę prototypowego łożyska foliowego smarowanego wodą ze szczególnym uwzględnieniem wpływu geometrii elementów podatnych łożyska na jego sztywność. Opisano technologię jego wykonania oraz model obliczeniowy łożyska opracowany z wykorzystaniem MES, przedstawiono wyniki wybranych analiz obliczeniowych.
-
Micro- and nano-level of bio-joint lubrication = Smarowanie biołożysk na poziomie mikro i nano
PublicationSmarowanie stawów człowieka koncentruje się w głównej mierze na tarciu granicznym oraz na tarciu mieszanym w cienkiej warstwie cieczy synowialnej zalegającej pomiędzy łatwo odkształcalnymi powierzchniami miękkiej chrząstki stawowej, na której wysokości chropowatości zmieniają się z czasem trwania procesu smarowania.Wartości sił tarcia granicznego ulegają zmianie w przypadku zmian wysokości nierówności dochodzących do dziesiątych...
-
The influence of roughness and geometrical structure of tissue surface on friction forces during the tissue cultivation in bioreactor = Wpływ chropowatości i geometrycznej struktury powierzchni tkanki na siły tarcia podczas hodowli tkanek w bioreaktorze
PublicationNajnowsze trendy naukowe w Unii Europejskiej i w USA w zakresie biotribologii idą w kierunku uwzględnienia zmian chropowatości zewnętrznej powierzchni tkanki w trakcie procesu hodowli w bioreaktorze.W mikrokontenerach bioreaktora hodowana tkanka jest permanentnie zraszana i polewana mediami o odżywczych oraz terapeutycznych właściwościach nienewtonowskich, gdzie często są to ciecze z odpowiednimi dodatkami lepko-sprężystymi wywołującymi...
-
Method of determining to the solving of friction forces on the tissue surface in bioreactor = Numeryczny wkład do wyznaczania sił tarcia na powierzchni tkanki w bioreaktorze
PublicationNiniejsza praca przedstawia metodę całkowania równań ruchu lepko-sprężystej cieczy odżywczej w cienkiej warstwie granicznej na powierzchni komórek chrząstki (chondrocytów), podczas nieustalonego procesu ich hodowli w bioreaktorze. Układ równań podstawowych w trójwymiarowej przestrzeni składa się z trzech równań zachowania pędu oraz z równania ciągłości. Proces hodowli komórek w bioreaktorach zależy od własności cieczy odżywczych.Ponieważ...
-
Equations of tribological parameters for liquid flow in boundary layer on the tissue surface in bioreactor = Wyznaczanie parametrów tribologicznych dla przepływu cieczy w warstwie granicznej na powierzchni tkanki w bioreaktorze
PublicationW niniejszej pracy przedstawiony został problem tribologiczny wynikający z przepływu nieustalonego odżywczej cieczy lepkiej w cienkiej warstwie przyściennej w bezpośrednim kontakcie z zewnętrzną powierzchnią warstwy wierzchniej wzrastających komórek (chondrocytów) w trakcie procesu ich hodowli w bioreaktorze. Efektem rozważań będą wartości sił tarcia powstające na powierzchni wzrastającej tkanki. Najnowsze badania wykazały lepszą...
-
Materiały ceramiczne w łożyskach ślizgowych
PublicationOpisano obszary zastosowań ceramiki maszynowej w węzłach ślizgowych maszyn. Przedstawiono rodzaje ceramiki stosowane w łożyskowaniu ślizgowym. Przedstawiono produkowane fabrycznie ceramiczne łożyska ślizgowe.
-
Problem wyboru bezsmarowego materiału ślizgowego dla łożysk pracujących w warunkach małych oscylacji
PublicationOmówiono przyczyny przyspieszonego zużywania się elementów węzłów łożyskowych, w których zastosowano ekologiczne materiały bezsmarowe. Wykazano szczególny wpływ oscylacji o małej amplitudzie - najczęściej występujących w sposób niezamierzony w pracy łożyska - na zużywanie się materiałów.
-
Badania doświadczalne układu indywidualnego zasilania poprzecznego łożyska ślizgowego
PublicationPrzedstawiono wyniki testów doświadczalnych nowego układu indywidualnego zasilania poprzecznego łożyska ślizgowego, którego działanie oparte jest na współpracy stałego pierścienia smarującego i prowadnicy hydrodynamicznej. Przedstawiono budowę stanowiska badawczego i metodykę badań. Wyznaczono charakterystyki objętościowego natężenia przepływu, ciśnienia i temperatury oleju w funkcji prędkości obrotowej i parametrów geometrycznych...
-
THE COMPARATIVE ANALYSIS OF PREPARED MIXTURES OF CRAMBE ABYSSINICA SEED OIL WITH MINERAL AND SYNTHETIC OIL
Publication -
METHODS OF THE MODIFICATION OF VEGETABLE OILS IN ORDER TO OBTAIN BASE OILS
Publication -
ANALYSIS OF TRIBOLOGICAL PROPERTIES OF VEGETABLE GREASES FOR APPLICATIONS IN AGRI-FOOD INDUSTRIES
Publication -
THE TRIBOLOGICAL PROPERTIES OF LUBRICATING GREASES BASED ON RENEWABLE OILS
Publication -
THE INFLUENCE OF DIFFERENT VEGETABLE DISPERSION PHASES ON THE ROLLING CONTACT FATIGUE OF BIODEGRADABLE LUBRICATING GREASES
Publication -
A new concept of measuring the friction forces for cartilage and polymers with viscoelastic properties
PublicationReferat przedstawia nową koncepcję dotyczącą pomiaru niskich sił tarcia oraz właściwości materiałów lepkosprężystych. Zaprezentowano: ogólny zarys metody pomiaru, wskazania dotyczące projektowania i budowy urządzenia pomiarowego, model matematyczny oraz sposób identyfikacji parametrów modelu. Metoda ta jest szczególnie przydatna w przypadku analizy właściwości materiałowej polimerów oraz tkanki chrząstki stawowej człowieka, zarówno...
-
EXPERIMENTAL STUDY OF SURFACE ROUGHNESS EFFECT ONTHE RHEOLOGICAL BEHAVIOR OF MR FLUID
PublicationPaper presents the results of shear stress measurements of a commercial magnetorheological fluid using a plate-plate type geometry with a modified working surface. The purpose of the study was to determine the effect of changing the roughness of the measuring plate on the obtained shear stress results. Controlled shear rate tests and Magneto Sweep measurements were carried out for three MR fluid layer heights. The tests were...
-
THE COMPARATIVE ANALYSIS OF ECOLOGICAL LUBRICANTS
Publication -
EFFECT OF THE BIO-LUBRICANT ON THE LUBRICATINGPROPERTIES AND SURFACE OF THE FRICTION ZONE
Publication -
THE EVALUATION OF THE ABRASIVE WEAR OF THE TI13Nb13ZR ALLOY IMPLANTED BY NITROGEN IONS FOR FRICTION COMPONENTS OF THE HIP JOINT ENDOPROSTHESES
PublicationZ uwagi na potrzeby społeczne, a zwłaszcza rosnące zapotrzebowanie na endoprotezy stawów biodrowego i kolanowego oraz uwzględniając fakt, że procesy tribologiczne odgrywają wiodącą rolę w procesie utraty stabilności endoprotez ortopedycznych i decydują o ich trwałości, uznano za celowe przeprowadzenie oceny wpływu implantacji jonowej na zużycie ścierne biostopu Ti13Nb13Zr. Do badań wykorzystano pary trące: nieimplantowany stop...
-
COMPARISON OF THE ABRASION RESISTANCE OF THE SELECTED BIOMATERIALS FOR FRICTION COMPONENTS IN ORTHOPEDIC ENDOPROSTHESES
PublicationRosnące z każdym rokiem zapotrzebowanie na endoprotezy stawów ortopedycznych przy jednoczesnym dążeniu do zwiększenia ich trwałości i wyeliminowania negatywnych skutków ubocznych produktów zużycia, które mogą wywoływać proces zapalny w tkankach determinuje potrzebę poszukiwania nowych biomateriałów, bądź metody modyfikacji ich powierzchni. Nadrzędnym celem prowadzonych przez nas badań było oszacowanie intensywności zużycia ściernego...
-
BEARING SYSTEMS OF WIND TURBINES – MAINTENANCE PROBLEMS
PublicationW praktyce eksploatacyjnej turbin wiatrowych o tradycyjnej konstrukcji (przekładniowych) obserwowana jest duża awaryjność przekładni, a zwłaszcza łożysk tocznych szybkoobrotowych wałów przekładni. W Polsce na zlecenie właściciela dużej farmy wiatrowej, firmy Energa Wytwarzanie S.A., Politechnika Gdańska we współpracy z Politechniką Poznańską i Akademią Górniczo Hutniczą podjęły badania mające na celu diagnozowanie przyczyn uszkodzeń...
-
THE EFFECT OF THE FRICTION OF THE REFUSE INSIDE THE REFUSE COLLECTION VEHICLE BODY ON THE WORKING PARAMETERS OF THE COMPACTION MECHANISM
PublicationMechanizm prasujący pojazdu do usuwania odpadów z pojemników (w skrócie PUOP) spełnia dwie funkcje. W pierwszym etapie zagęszcza zebrane z pojemników odpady, a następnie przemieszcza je w głąb skrzyni zbiorczej. Znajo-mość właściwości mechanicznych odpadów znajdujących się wewnątrz skrzyni może w znaczący sposób wpłynąć na poprawę wydajności pojazdu. Celem ba-dań było zwiększenie wydajności PUOP poprzez opracowanie w oparciu...
-
WEAR OF Si OR B DOPED AMORPHOUS CARBON COATINGS
PublicationThe paper describes a complex wear research on DLC (amorphous carbon) moped with boron (B) and silicone (Si). The tests were carried out in two different sliping systems: flat–on–flat (ring contact, unidirectional sliding) and ball–on–flat (reciprocating sliding). Water and medical saline solutions were used as lubricants. A comparative analysis of the results revealed differences in the initiation and progress of wear and the...
-
The effect of the exposure-in-oil on the contact of the polymers forming sliding layers in hydrodynamic bearings. Wpływ ekspozycji w oleju na kąt zwilżania polimerów stosowanych na warstwy ślizgowe w łożyskach hydrodynamicznych.
PublicationPolimery stosowane jako warstwy ślizgowe w hydrodynamicznych łożyskach wzdłużnych to zazwyczaj tworzywa termoplastyczne charakteryzujące się relatywnie wysokimi wartościami kątów zwilżania w porównaniu z metalami. Metale, w tym również Babbitt czy inne stopy łożyskowe, cechują niskie wartości kątów zwilżania. Im niższy kąt, tym powierzchnia lepiej się zwilża. Tworzywa sztuczne wykorzystywane w węzłach tribologicznych mających zapewnić...
-
OPERATING CONDITIONS OF SLIDE BEARINGS OF MILLS USED IN KGHM POLSKA MIEDŹ S.A.
PublicationThe paper contains the results from a tec hnical analysis of the conditions of the operation of hydrodynamic bearings supporting the drums of ore processing mills at KGHM Polska Mied ź S.A. A theoretical analysis was performed on the grounds of onsite examination and measurem ents of principal dimensions of the bearings of interest. The computer simulation covered the characteristics of the oil film in the bearings...
-
HYDRODYNAMIC THRUST BEARINGS WITH POLYMER LINING
PublicationPolymeric linings of sliding surfaces of the hydrodynamic bearings have been used successfully for over 50 years. Despite of their long history of operation and research, they have not become wide spread in industrial applications. This fact may be surprising, considering th e conclusions that have been published concerning bearing operation and design. This paper summarizes the current...
-
Impact analysis of surface roughness of the plate-plate measuring system on resistance torque in interaction with MR fluid
PublicationMagnetorheological (MR) fluids are complex suspensions of magnetic particles in a non-magnetic carrier fluid. They exhibit ‘smart’ properties that enable them to change their rheological parameters in response to a change in the external magnetic field applied. This behavior is used in some engineering solutions, e.g. MR clutches or brakes. For such systems to work correctly, the resistance torque achieved by contact with the...
-
ANALYSIS OF UNCONTROLLED WEAR IN THE AREA OFA BELLEVILLE SPRING OF A FRICTION TORSIONAL VIBRATIONDAMPER IN A MOTOR VEHICLE CLUTCH
Publication -
Analiza naprężeń w ceramicznych elementach tocznych
PublicationW pracy przeprowadzono metodą elementów skończonych (MES) analizę stanu naprężenia w strefie pęknięcia kolistego kulki ceramicznej wykonanej z azotku krzemu poddanej naciskom hertzowskim. Naprężenia analizowano dla pęknięć, które najczęściej są spotykane na powierzchni kulek ceramicznych. Obliczenia numeryczne prowadzono za pomocą programu ANSYS. Rozwiązania numeryczne porównywano z wynikami badań doświadczalnych propagacji tego...
-
ANALYSIS OF THE POSSIBILITIES OF HIGH SPEED SHAFT BEARING SYSTEM DURABILITY INCREASE
PublicationDuring the operation of wind turbines with a gearbox of traditional configuration, a high failure rate of high-speed shaft bearings is observed. Such a high failures frequency is not reflected in standard bearing durability calculation methods, which can be attributed to atypical failure mechanism. To avoid observed problems in the 1.5 MW wind turbine, the modification of the existing bearing system is proposed. Multiple options,...
-
AN ATTEMPT AT IDENTIFYING THE INFLUENCE OF TEST HEAD ASSEMBLY STIFFNESS ON THE RESULTS OF A TRIBOLOGICAL EXPERIMENT CONDUCTED UNDER MICRO-OSCILLATION CONDITIONS
PublicationThe outcome of experimental research on a group of dry bearing materials carried out under small oscillation conditi ons and using a test rig designed and made at Gdansk University of Technology inspired the decision to find out if the stiffness of test head elements in fluenced the generated results. Therefore, a computer model utilising finite elements was devised and used to simulate the workings of the test head. The mode l...
-
ATTEMPT AT EVALUATING THE INFLUENCE OF BENDING STRESS ON SHAFT WEAR PROCESSES IN WATER LUBRICATED SLIDING BEARING WITH A RUBBER BUSHING
PublicationWater lubricated bearings find increasingly wide application in shipbuilding or hydro–power industry, the popularity stemming from their numerous advantages. Unfortunately, as it turns out, water lubricated bearings do not always meet expectations, as on occasion they become subject to intense, premature wear which requires costly repair. One of the still unexplained phenomena is the process of excessive bearing wear, in particular...
-
Prospects of Decreasing Power Losses in a Hydrostatic Thrust Bearing
PublicationIn numerous machines, axial load is carried by tilting pad thrust bearings known since the beginning of 20th century. These bearings are commonly bath lubricated, which is simple, does not require any additional pumps, and, due to this, such systems are highly reliable. In a contemporary technology, however, minimization of friction losses became an important goal of machinery improvement. Calculations based on elementary rules...
-
Search for the most useful geometry of an acoustic journal bearing
PublicationComputer simulations of a number of journal bearing’s geometries utilising acoustic levitation were carried out. The choice of the best geometry depended on the ability of a deformed shape, created by piezo-electric elements, to facilitate squeeze film ultrasonic levitation, and also to create three evenly distributed diverging aerodynamic gaps. Deformations of analysed variants of the bearing’s shape were generated by numerical...
-
ANALYSIS OF THE LOAD-CARRYING CAPACITY OF A HYDRODYNAMIC WATER-LUBRICATED BEARING IN A HYDROELECTRIC POwER PLANT
PublicationThe paper presents an analysis of the load-carrying capacity of a historic hydrodynamic water-lubricated radial bearing of an unconventional segment design installed in the Braniewo Hydroelectric Power Plant. The aim of the calculations was to determine whether the bearing operates in the conditions of hydrodynamic or mixed lubrication, as well as to establish the optimal geometry of the axial grooves allowing for the highest load-carrying...
-
ANALYSIS OF BEARING CLEARANCE AND WIDTH OF OIL GROOVE ON CHARACTERISTIC OF FLUID FILM IN HYDRODYNAMIC MAIN CRANKSHAFT BEARINGS
PublicationAbstract Paper represents analysis of influence of oil groove width and bearing clearance on characteristics of oil film in hydrodynamic journal main crankshaft bearing. Analysis was performed in purpose to define influence of bearing clearance and dimensions of oil groove on static characteristics and manufacturability of half shelf bearings in industrial high-volume production. Computer simulations was made using ARTbear program...
-
DESIGN AND THEORETICAL ANALYSIS OF A PROTOTYPE TILTING-PAD RADIAL BEARING WITH ADJUSTABLE CLEARANCE
PublicationThe article introduces a design and analysis results of a prototype ORC (organic Rankine cycle) turbo generator rotor assembly of 300kW power, supported by tilting-pad bearings of original design. The calculations were performed for a prototype turbo generator rotor. The shaft of this machine is supported with two radial bearings, lubricated with an unusual lubricant – a low-boiling-point agent. The main objective of the presented...
-
Analysis of ring cracks in ceramic rolling elements using the boundary element method
PublicationCeramic materials have been increasingly used in bearing technology for over a dozen years. This is due to the characteristic properties of ceramic materials such as: high hardness, corrosion resistance, the possibility of use in aggressive chemical environments, as well as due to the lower specific weight compared to steel materials. However, the use of ceramic materials is connected with many limitations. The main disadvantages...
-
A SEARCH OF AN INDUCER GEOMETRY THAT IS BENEFICIAL FOR LIFTING PARAMETERS OF A LIFTED OBJECT OF A SELECTED SHAPE
PublicationThe literature describes acoustic levitation phenomena with the utilization of air squeeze film between the vibrating inducer and the lifted object. The objective of the study is to determine the shape of the inducer with vibration characteristics that would allow the levitation of an object of the assumed geometry. In this paper, the influence of the dimension ratio of the inducer on the frequency of the first mode of vibration...
-
The Impact Of The Selected Parameters Of Fdm Manufacturing Technology On Tribological Performance Of Abs–Steel Pair Under Dry Friction
PublicationThe paper presents the result of tribological test of ABS and steel samples sliding under dry friction. Polymeric samples were manufactured of ABS material using FDM technology. Testing was carried out in unidirectional sliding in a ring-on-flat contact in a PT-3 tribometer. The scope of tested parameters included volumetric and mass wear, the friction coefficient, and polymeric specimen temperature. Polymeric specimens used in...
-
THEORETICAL AND EXPERIMENTAL INVESTIGATION OF THIN-WALLED BEARING SHELL’S DESIGN PARAMETERS AND ASSEMBLY CONDITIONS ON THE HOLDING TORQUE INSIDE A HOUSING BORE OF A CONNECTING ROD
PublicationThe aim of the work was the experimental and theoretical evaluation of the influence of the most important parameters determining the holding torque of a thin-walled bearing shell inside a housing bore of a connecting rod. The main investigated parameters were defned by authors experience in this feld. In the frst stage of research, a special test stand was designed in order to allow measuring the real values of the friction torque...
-
HYDROSTATIC THRUST BEARING WITH REDUCED POWER LOSSES
PublicationIn many cases in rotating machinery, axial load is carried by tilting pad thrust bearings which have been developed since the beginning of 20th century. For high reliability and simplicity, most commonly the bearings are bath lubricated. In the times of sustainable development, however, minimization of friction losses becomes an important criterion for machinery assessment, and a strategic goal of their development. Performed calculations,...
-
The use of plate springs for preloading of a system of tapered roller bearings of a wind turbine gearbox
PublicationThe use of preloaded tapered roller bearings in wind turbine drive systems allows a transfer of load in the case of high variations of axial forces. The examined bearing system, a modification of a current design, consists of a pair of different sized bearings. Previous study showed the high sensitivity of tapered roller bearings on the existing radial interference. Dimensional tolerances used in the original design do not allow...
-
A COMPARISON OF WEAR PROPERTIES OF WATER LUBRICATED NBR AND PTFE SLIDING BEARINGS
PublicationThe excessive wear of a journal shaft can be caused by many factors, for example, working conditions (e.g., temperaturę, slip speed, the type of lubricant), pressure, the type of material used on the bearings and shafts and their roughness, as well as contamination remaining in the system. This paper presents the roughness profiles co-operating with a rubber (NBR) and polytetrafluoroethylene (PTFE) bushes. The conditions of cooperation...
-
EXPERIMENTAL EVALUATION OF DLC/STEEL SLIDING CONTACTS’ OPERATIONAL ENVELOPE
PublicationIn an industrial project concerning sliding bearings, a sliding pair was selected of high alloy steel vs. industrial grade DLC coated high alloy steel as a basis for an innovative design of high performance sliding bearings lubricated with a synthetic oil for use in geared transmission units. The development process required credible data on the ultimate resistance of the sliding pair to very high contact stress. An experimental...
-
THE ANALYSIS OF THE INFLUENCE OF STRESS DISTRIBUTION ON WEAR PROFILE IN LUBRICATED SLIDING CONTACT OF UHMW-PE VS TITANIUM Ti-13Nb-13Zr ALLOY
PublicationMetal – polymer sliding contacts are a typical combination in industry and medicine. For decades such a set of materials has been the primary choice in human joints endoprosthetic technology. In this paper tribological issues of are presented from a research on the potential for practical use of Ti-13Nb-13Zr/UHMW-PE couple for orthopedic endoprosthesis. In tests on simplified models it is critically important to carefully...