Filters
total: 4982
filtered: 4207
-
Catalog
- Publications 4207 available results
- Journals 66 available results
- Conferences 4 available results
- Publishing Houses 3 available results
- People 116 available results
- Inventions 8 available results
- Projects 18 available results
- Laboratories 1 available results
- Research Teams 3 available results
- e-Learning Courses 76 available results
- Events 19 available results
- Open Research Data 461 available results
Chosen catalog filters
displaying 1000 best results Help
Search results for: STAŁE ELEKTROLITY
-
Nonlinear and linear impedance of bismuth vanadate ceramics and its relation to structural properties
PublicationThe nonlinear and linear electrical properties, topography, and microstructure of bismuth-vanadate ceramics, were studied. The structurewas observed with the use of X-ray diffraction (XRD), scanning electronmicroscopy (SEM), atomic force microscopy (AFM) and confocal microscopy methods. The obtained results showed that ceramic is porous. Two phase transitionswere determinedwith the use of DSC measurements. The linear and nonlinear ac...
-
Fabrication and properties of electrode material composed of ordered titania nanotubes and pEDOT:PSS
PublicationWe report on the two-stage preparation method of electrode material composed of titania nanotubes and poly(3,4-ethylenedioxythiopene):poly(2-styrenesulphonate) conductive polymer (pEDOT:PSS). Initially, titania nanotube arrays were produced by the anodization process of Ti substrate. Next, the polymer was potentiostatically deposited onto the thermally annealed nanotube arrays from the electrolyte containing monomer and counter...
-
Electronic and ionic relaxations in strontium-borate glass and glass-ceramics containing bismuth and vanadium oxides
PublicationThe topography, microstructure and electrical properties of strontium-borate glass and SBO glass containing bismuth and vanadium oxides, were studied. The structure was measured using X-ray diffraction (XRD), Energy Dispersive X-ray Spectrometer (EDS) and Scanning electron microscope (SEM) methods. The A.C. complex conductivity was investigated as a function of temperature and frequency. The influence of the quantity of bismuth...
-
Investigations on the influence CuO doping on elastic properties of Li2SO4–MgO–P2O5 glass system by means of acoustic wave propagation
Publication -
Phase investigations of copper based CuZn38Al2MnFe alloy
PublicationW pracy przedstawiono analizę fazową mosiądzu CuZn38Al2MnFe. Wykazano, że obecność fazy Fe4Mn77Si19 powoduje kruchość stopu w teście zginania próbek.
-
Electrical properties of A-site Ca-doped LaNb1-xAsxO4-δ ceramics
PublicationThe electrical properties of A-site Ca-doped LaNbO4 with the addition of As in the B-site, have been investigated. Total, grain- and specific grain boundary electric conductivities in different oxygen partial pressure, and water vapour partial pressure were determined. Additional conductivity measurements were performed in nitrogen, to suppress the possible p-type conductivity, focusing on protonic conductivity. The maximum measured...
-
Synthesis and structural properties of (Y, Sr)(Ti, Fe, Nb)O3−δ perovskite nanoparticles fabricated by modified polymer precursor method
PublicationThe yttrium, iron and niobium doped-SrTiO3 powders have been successfully fabricated by a modified low–temperature synthesis method from a polymer complex. The usage of strontium hydroxide precursor instead of conventional strontium nitrate or strontium carbonate provides to the possibility of significant decrease of annealing temperature. It allows to prepare a material with sphere-shape grains of nanometric size (15–70 nm). The...
-
Identification of Kinematic Excitation Function by the Modal Coordinates Estimation of the System's Dynamics
PublicationThe paper presents a method of the kinematic excitation courses’ identification in excitation points, based on the car road test acceleration at different measurement points. For the purpose of the laboratory fatigue life investigation of contemporary complex structures (e.g. cars bodies) and components of these structures (i.e. cars roofs), only a few first vibration modes are usually taken into account. During real life tests...
-
SmallAngle Neutron Scattering Study of the Structure of Mixed Micellar Solutions Based on Nonionic and Two Cationic Surfactants
PublicationThe aggregation in mixed water systems based on nonionic surfactant, i.e., heptaethylene glycol monotetradecyl ether (C14E7), and cationic surfactants, i.e., cetyltrimethylammonium bromide (CTAB), and cetyltrimethylammonium chloride (CTAC) has been investigated using the smallangle neutron scattering method. The preliminary results of the study of the behavior of C14E7 aqueous solutions (for a concentration of 0.17%) when adding...
-
Influence of pyrolysis atmosphere on the lithium storage properties of carbon-rich polymer derived SiOC ceramic anodes
PublicationPolymer derived carbon-rich SiOC ceramics are prepared from polysiloxane precursors through a pyrolysis process at 1000 °C using pure argon and argon/hydrogen mixture as pyrolysis atmosphere. The precursor is synthesized from a linear (Si–H)-containing polysiloxane cross-linked with divinylbenzene using hydrosilylation reaction in the presence of a platinum catalyst. Pyrolysis in Ar/H2 mixtures, compared to the treatment under...
-
A simplified model of 3-D pipe system conveying flowing liquid
PublicationThe paper presents a model reduction technique of a 3-D pipe system with flowing liquid. In the analysis and design of control (mechatronic) systems it is useful to work with simple, low order models. A hybrid reduced order model is proposed. The system model consists of two parts, the modal model and the finite element model.
-
Donor-substituted SrTi1+xO3−δ anodes for SOFC
PublicationNonstoichiometric Nb-substituted SrTiO3 compounds were investigated in order to discuss the influence of nonstoichiometry at the sample properties in the light of recent results reported in the literature. Structural and electrical properties of samples were characterized. Investigated compounds were also applied as anodes for Solid Oxide Fuel Cells and their reactivity with YSZ electrolyte was examined. The defect chemistry explaining...
-
Solid Oxide Fuel Cells with Ni infiltrated perovskite anode
PublicationNiobium-doped strontium titanate was used as the anode for a solid oxide fuel cell. Electrolyte-supported cells were prepared with pure perovskite and composite perovskite–yttria–stabilized-zirconia (YSZ) anodes. Fuel cell tests demonstrated significant improvement in power density after infiltration with a small amount of Ni. The obtained values of power densities are comparable with conventional Ni/YSZ cermet anode. In addition,...
-
Modelling of Geared Multi-Rotor System
PublicationIn the paper the method of modelling a speed-varying geared rotor system is presented. The proposed approach enables us to obtain an accurate low-order lumped parameter representation of the investigated system. The final model consists of reduced modal models of an undamped beam/torsional shaft system as well as a spatially lumped model of other linear and nonlinear phenomena including gear mesh interaction.
-
HILS for the Design of Three-Wheeled Mobile Platform Motion Surveillance System with a Use of Energy Performance Index
PublicationCurrent tendency in mechatronic design requires the use of comprehensive development of an environment, which gives the possibility to prototype, design, simulate and integrate with dedicated hardware. The paper discusses the Hardware-In-the-Loop Simulations (HILS) mechatronic technique, used during the design of the surveillance system based on energy performance index. The presented test configuration (physical controller – emulated...
-
New ceramic materials derived from pyrolyzed poly(1,2-dimethylsilazane) and starch as a potential anode for Li-ion batteries
PublicationNewmaterialswere obtained by pyrolysis of starch (S) and poly(1,2-dimethylsilazane) (PSN) (weight ratio: PSN/S 30/70) at temperature a) 500 °C, b) 700 °C and c) 900 °C. Ceramic materials were characterized by infrared spectroscopy, TGA, Raman spectroscopy and SEM. New Si\O and shifted Si\C stretching vibration modes emerged confirming direct interaction between silicon originating fromsilazane and oxygen coming fromstarch. The...
-
Electronic conductivity in the SiO2-PbO-Fe2O3 glass containing magnetic nanostructures
PublicationThe linear impedance spectra of iron–silicate–lead glass samples were measured in the frequency range from 1 MHz to 1 MHz and in the temperature range from 153 K to 423 K. The structure was investigated by means of XRD and atomic force microscopy. Local electrical and magnetic properties of the samples were tested with the aid of electrostatic force microscopy (EFM) and magnetic force microscopy (MFM). The obtained results show...
-
Electrical properties and structure of lead-borate glass containing iron ions.
PublicationThe ac and dc conductivity in iron–lead-borate glass samples was investigated in the frequency range from 1 mHz to 1 MHz and in the temperature range from 153 K to 423 K. The structure was investigated by the means of atomic force microscopy (AFM) and the crystalline phases (if present) were identified by the means of X-ray diffractometry. Two types of ac electrical behaviour were observed. The first group of glass samples which...
-
Tailoring of SiOC composition as a way to better performing anodes for Li-ion batteries
PublicationPolymer derived silicon oxycarbide (SiOC) ceramics are investigated as potential anodes for lithiumion batteries. Different SiOC ceramics are prepared by pyrolysis (1000 °C and 1400 °C under controlled argon atmosphere) of polysiloxanes ceramic precursors. Preceramic polymers are synthesized using the sol–gel method. Phenyltriethoxysilane (PhTES) and methyltriethoxysilane (MTES) have been used as starting precursors and mixed with...
-
The effect of pre-hydrogen charging on corrosion behaviour of superduplex stainless steel welded joints
PublicationThe paper presents results of research undertaken to determine the influence of hydrogen on passivity and corrosion resistance of 2507 super duplex stainless steel welded joints. Butt welded joints were made with low heat input using flux corded arc welding (FCAW) method. Coupons of 5.0 x 5.0 mm were cut from the welded joints containing weld metal (WM), heat affected zone (HAZ) and parent metal (PM). Hydrogen was introduced...
-
Deformation of the Structural Details of the Components Created by the Rapid Prototyping Method
PublicationThe paper present the results of preliminary research and describes the deformation of construction details within the process of producing small element employing a stereography system. The article discuses a scheme for changes in data conversion. Variation in construction details have been described on the basis of analysing photographs.
-
Hardened Steel Surface Waviness Created by Rolling Burnishing Process
PublicationThe surface of the finishing machined parts is defined mainly by roughness parameters. Growing demands on the part, especially mating sliding or rolling, require the specification of additional parameters, such as waviness parameters, particularly when there is significant resistance to seizing or noise reduction. This paper presents surface waviness characteristics of hardened burnished steel.
-
The Roughness of the Hardened Steel Surface Created by the Rolling-Burnishing Process
PublicationBurnishing hard materials can be used as an alternative finishing process. this paper presents the results of burnishing hardened steel. The article discusses surface deformation that occurs during this process and depends on the selected parameters of the geometric structure of the force applied for surface burnishing.
-
Evaluation of Wear Resistance of Ti alloys used for elements friction of knee endoprosthesis
PublicationThe paper presents research results of resistance to abrasive wear of titanium alloys: Ti6Al4V (commonly used) and Til3Nb13Zr (alloy of new generation) in association with polyethylene (UHMW-PE) predisposed for elements on pair of the knee endoprosthesis. The results were analysed from the point of possibility of an use of new generation titanium alloys as components of such implants. The tests of resistance to abrasive wear of...
-
Photoelectrochemical properties of BIMEVOX (ME=Cu, Zn, Mn) electrodes in contact with aqueous electrolyte
PublicationLayered oxide Bi4O2O11 and mixed oxides of bismuth, vanadium and a third metal (ME = Cu, Zn, Mn) were synthesized and characterized using XRD, Raman and SEM. The energy band gap (Eg) of samples determined using UV–VIS reflectance spectra equals to 2.46, 2.34, 2.27 and 2.18 eV for Bi4V2O11, BICUVOX (Bi2V1 − xCuxO5.5 − 3x/2), BIZNVOX (Bi2V1 − xZnxO5.5 − 3x/2) and BIMNVOX (Bi2V1 − xMnxO5.5 − x/2) (x = 0.1), respectively. Open circuit...
-
Multi Parameter Sliding Test Result Evaluation for The Selection of Material Pair for Wear Resistant Components of a Hydraulic motor Dedicated for Use With Environmentally Friendly Working Fluids
PublicationIn the paper the method and results are presented of the testing of tribological performance of a number of hard materials available commercially. The tests consisted in unidirectional sliding with liquid lubrication. The load and velocity regime chosen were similar to a standard four-ball lubricity test with constant velocity and load increasing over time. The regime was modified in such a way that over the initial part of the...
-
Investigation of catalytic layers on anode for solid oxide fuel cells operating with synthetic biogas
PublicationIn this paper solid oxide fuel cells operating with dry synthetic biogas have been examined. In order to increase their stability the layers of CuO-CeO2, Cu1.3Mn1.7O4 and Y0.08Sr0.92Ti0.8Fe0.2O3 -δ have been deposited on the Ni-YSZ anode site. These layers should catalyze the internal biogas reforming and prevent the carbon deposition on the anode site. It has been found that CuO-CeO2 and Cu1.3Mn1.7O4 catalysts led to an increase...
-
The Influence of Modelling Material Zones on Strains and Stresses at Weld Toe Notch
PublicationThe latest development in the field of welding technology enabled prefabrication of thin-walled sandwich structures in an industrial scale. Sandwich structures fabricated of steel, or aluminium alloy plates and stiffeners are welded with the use of hi-power CO2 lasers. Strength analysis of such structures with the use of finite element method needs proper material modelling.In this paper the material model of steel sandwich panel...
-
Influence of Spatial Structures of 316L Stainless Steel on Its Cavitation Erosion Resistance
PublicationCavitation erosion performance of modified macroscopic internal structure 316L stainless steel was investigated. The samples processed by means of SLM method were subjected to cavitation erosion test. The scanning electron microscope Philips 30/ESEM was used to examine morphology of eroded surface.
-
Effect of Some Sulphur Additives on The Degradation of 9Cr-1Mo Steel After Its 10 Years Service in The CCR Platforming Unit
PublicationThe work shows the results of the tests of 9Cr-1Mo steel, which was for 10 years operated in the CCR platforming unit in Group Lotos SA in Gdańsk, and then in the laboratory was sulphidised during 166 h at a temperature of 600 °C. Sulphidation was performed in a mixture of H2-H2S gases at the vapour pressure of sulphur 4.1·10-14 atm, so the order of magnitude of vapour pressure was less than that of the dissociation pressure of...
-
Redundantly Actuated 3RRR Parallel Planar Manipulator - Numerical Analyses of its Dynamics Sensitivity on Modifications of its Platform’s Inertia Parameters
PublicationIn the paper, numerical analyses, as well as dynamics of a complex mechanism, are presented. Two objectives are crucial for the paper: inverse dynamic model is needed (dedicated to be use in the model predictive controller); an identification method is searched (some trajectory parameters are controlled, when specific trajectory is tracked under an open-loop model-based control), as selected parameters must be identified for the...
-
Wear of Electroplated Tools Used for Flat Grinding of Ceramics
PublicationTwo methods for the abrasive properties evaluation, based on the image processing, are presented in the paper. Image processing analysis was developed to evaluate quickly the abrasive properties as the tool wears down. The coefficient based on the image brightness was calculated and additional analysis was based on the number of grains located on the active surface of the tool before and after machining. The active surfaces of...
-
Surface Structure of Components Created by Stereolitography
PublicationStereolithography is an additive rapid prototyping method. This method is based on the principle of solidifying a liquid photopolymer (resin) by laser radiation. Models obtained with this method are characterized by a specific surface structure called “stairstep effect”. It causes that, the surface should be processed by additional finishing (postprocessing). To minimize the additional machining process, the model should be set...
-
Research on Tool Temperature Dependence on Lapping Grains Size
PublicationCommonly used as a finishing operation, lapping has been used for achieving ultra-high finishes and close tolerances between mating pieces. Its carried out by applying loose abrasive grains between work and lap surfaces, and causing a relative motion between them resulting in a finish of multi-directional lay. The grains activity (sliding and rolling) in the working gap causes not only the material removal but also the temperature...
-
The Influence of Workpiece Hardness on Plate Temperature during One Side Lapping
PublicationLapping leads to a surface with low roughness and high precision. Because of required parts accuracy tool flatness is the key to the successful machining. To avoid its excessive thermal expansion, plate temperature research was taken. The goal was to determine the correlation between the basic lapping conditions and wheel temperature. In work Bulsara et al. authors developed model to estimate the maximum and average temperature...
-
Comparison of Single and Multi-Population Evolutionary Algorithm for Path Planning in Navigation Situation
PublicationIn this paper a comparison of single and multi-population evolutionary algorithm is presented. Tested algorithms are used to determine close to optimal ship paths in collision avoidance situation. For this purpose a path planning problem is defined. A specific structure of the individual path and fitness function is presented. Principle of operation of single-population and multi-population evolutionary algorithm is described....
-
Influence of Flat Lapping Kinematics on Machinability of Ceramics
PublicationNew tools for flat grinding of ceramics are presented in the paper. Electroplated CBN tools (B64 and B107) were used in a modified single-disc lapping machine configuration. The results from experiments, such as the material removal rate and surface roughness parameters are presented and analyzed. Numerical simulations, based on the model for the shape error and tool wear estimation in machining with flat lapping kinematics, are...
-
Technological Problems in Lapping on Flat Surfaces of Ceramic Parts
PublicationThis paper will present the results of research on single-disc lapping of flat surfaces of small ceramic elements. Machining with the use of different tools such as metallic, two-metallic and abrasive-metallic will be analyzed. The basics and techniques of reinforcement of laps will be discussed. The results of the influence of parameters on the surface quality of ceramic conponents (sealing) for three treatments on lapping machines...
-
Chemical instability of the cobalt oxyhydrate superconductor under ambient conditions
Publication -
Superconductivity in three-layer Na0.3CoO2·1.3H2O
Publication -
Generation of Optimal Process Plan Alternatives for Manufacturing Mechanical Components
Publication -
Application of Syntactic Pattern Recognition Approach in Design and Optimisation of Group Machining Systems
Publication -
The effect of Fe and Ru substitution on the superconductivity in MgCNi3
Publication -
Composite (La, Sr)MnO3-YSZ cathode for SOFC
PublicationW pracy przedstawiono właściwości elektryczne kompozytów (La,Sr)MnO3-YSZ. Materiały te dzieki swoim włąściwościom mogą staniwć dobry materiał na katody ogniw paliwowych. Przedstawiono też wyniki badań ogniwa paliwowego pracującego z paliwem wodorowym zbudowanego na bazie katody z kompozytu LSM-YSZ i anody Ni-YSZ. Uzyskano gęstośc mocy 0.26 W cm−2 przy temperaturze 850°C.
-
Electrical properties of nanocrystalline Sm-doped ceria ceramics
PublicationWłaściwości ceramiki z cerii zależa zwykle silnie od struktury ziaren. W pracy przedstawiono właściwości elektryczne ceramiki z cerii domieszkowanej samarem wykonanje w technologii 'net shape' posiadającej strukturę nanokrystaliczną.
-
Optimum Control of Gyroscopic Systems
PublicationThe problem of optimum control of transverse rotor vibrations with gyroscopic interactions has been described and solved in the paper. An integral performance index has been defined for such system in order to minimize vibration level of a chosen rotor point. For this reason, an efficient way of finding the weight coefficients of integral performance index for multi-degrees-of-freedom system with gyroscopic interactions has been...
-
CGO as a barrier layer between LSCF electrodes and YSZ electrolyte fabricated by spray pyrolysis for solid oxide fuel cells
PublicationPerovskite La0.6Sr0.4Co0.2Fe0.8O3 − δ (LSCF) is often used as a cathode material for solid oxide fuel cells (SOFC) due to high mixed ionic and electronic conductivity and good catalytic activity. Unfortunately, sintering of the LSCF cathode together with the yttria stabilized zirconia (YSZ) electrolyte, leads to formation of the La2Zr2O7 and SrZrO3 phases in the interface. These phases increase the resistance of the cell. To avoid...
-
Analysis of Ceramic Elements with Ring-Crack Defects in Lubricated Rolling Contact
PublicationThe properties of ceramics, specifically low density, high hardness, high temperature capability and low coefficient of thermal expansion are of most interest to rolling element manufacturers. Surface ring cracks on lubricating rolling contact fatigue failure has been studied using numerical fracture analysis. Such cracks are very often found on ceramic bearing balls and decrease fatigue life rapidly. The numerical calculations...
-
Electrodes consisting of PEDOT modified by Prussian Blue analogues deposited onto titania nanotubes – Their highly improved capacitance
PublicationIn this work we present the outstanding energy storage of prepared inorganic-organic heterojunction where hydrogenated ordered titania nanotubes (H-TiO2NT) were modified by the hybrid made of poly(3,4-ethylenedioxythiophene) (pEDOT) and iron hexacyanoferrate centres (Fehcf, Prussian Blue). The material TiO2NT/pEDOT:Fechf was obtained electrochemically by means of: anodization, hydrogenation and finally, electropolymerization of...
-
Indoor atmospheric degradation of historical metal objects studied by spectroscopic techniques
Publication