Search results for: INFILL ANGLE
-
The influence of the fuel spray nozzle geometry on the exhaust gas composition from the marine 4-stroke diesel engine
PublicationThe paper presents experimental research on a 4-stroke, 3-cylinder, turbocharged AL25/30 Diesel engine. Research consisted in investigating the effect of the geometry of the fuel injectors on the exhaust gas composition from the engine. During measurements, the engine was operated with a regulator characteristic of a load range from 40 kW to 280 kW, made by electric water resistance. The engine was mechanically coupled to the electric...
-
Application of Analytic Signal and Smooth Interpolation in Pulse Width Modulation for Conventional Matrix Converters
PublicationThe paper proposes an alternative and novel approach to the PWM duty cycles computation for Conventional Matrix Converters (CMC) fed by balanced, unbalanced or non–sinusoidal AC voltage sources. The presented solution simplifies the prototyping of direct modulation algorithms. PWM duty cycles are calculated faster by the smooth interpolation technique, using only vector coordinates, without trigonometric functions and angles. Both...
-
Laser-assisted modification of titanium dioxide nanotubes in a tilted mode as surface modification and patterning strategy
PublicationElectrochemical anodization is regarded as a facile and easily scalable fabrication method of titania nanotubes (TiO2NTs). However, due to the extended duration of calcination and further modifications, much faster alternatives are highly required. As a response to growing interest in laser modification of nanotube arrays, a comprehensive investigation of pulsed-laser irradiation and its effect onto TiO2NT properties has been carried out....
-
Postquarter-Point Case of Ship’s Side-Berthing and Its Influence on Marine Fender Pitch
PublicationThis paper presents a critical analysis of some selected codes and practical recommendations used as basic rules in the design procedures of modern marine fender systems. The first part of the discussion pertains to the existing equations used in calculating the eccentricity coefficient in the ship’s kinetic energy equation and the maximum allowable fender pitch (spacing) in a set of fenders installed along a quay wall. A new approach...
-
Proposal of New Tracer Concentration Model in Lung PCT Study Comparison with Commonly Used Gamma-variate Model
PublicationPerfusion computed tomography (pCT) is one of the methods that enable non-invasive imaging of the hemodynamics of organs and tissues. On the basis of pCT measurements, perfusion parameters such as blood flow (BF), blood volume (BV), mean transit time (MTT) and permeability surface (PS) are calculated and then used for quantitative evaluation of the tissue condition. To calculate perfusion parameters it is necessary to approximate...
-
Principles and Practices of Corporate Governance in the Global Economy
PublicationThe book places ownership at the centre of all relevant choices that the company makes. In particular, it addresses the issue of governance from the perspective of ownership, and in a broader and more articulated sense than most Anglo-Saxon studies do. The authors analyse the relationship between ownership, governance, and corporate strategy, with a dual objective. On the one hand, the aim is to identify the consistency relationships...
-
A new approach to determination of the two-mass model parameters of railway current collector
PublicationThe paper presents two mathematical models of railway current collectors both with two degrees of freedom. The first one, hereinafter Pantograph Articulated Model (PAM), has one degree of freedom in rotational motion and the second degree of freedom in translational motion. The second model, called henceforth as Pantograph Reference Model (PRM), has both degrees of freedom in translational motion. Differential equations of the...
-
Magnetic field maps of an astable multivibrator in frequency range from 30 MHz to 3 GHz – selective detection
Open Research DataThe data presents a result of near field measurements of electromagnetic emissions radiated from the PCB of a small electronic device. An efficient method of modelling the magnetic and electric field emissions is the measurements in the near field using electric and magnetic probes. The attached files contain magnetic field maps created on based measurements...
-
Utilizing online collaborative games to facilitate Agile Software Development
PublicationEffective collaboration and interaction among the development team and between the team and the customer as well as proactive attitude in initiating and implementing improvements play vital roles in the success of agile projects. The challenge is how to address these social aspects since neither the Agile Manifesto nor the Scrum Guide specify techniques that aid the human side of software development. To fill this gap, we developed...
-
Effect of pH on optical sensing with poly-L-lysine-modified nanodiamonds
PublicationNitrogen-vacancy (NV) centers are crystallographic defects which provide diamonds with unique physical properties. The centers are known for their intensive, time-stable fluorescence, and an electron spin, which exhibits long coherence time and may be manipulated using external stimuli. Nanodiamonds containing the NV centers are promising tools in biolabeling, biosensing, and drug delivery due to the aforementioned properties of...
-
Voltammetric and biological studies of folate-targeted non-lamellar lipid mesophases
PublicationFolate-targeted lipid nanostructures are promising strategies for the development of biocompatible drug delivery systems. The objective of this study was to evaluate the efficacy of drug delivery to cancer cells by folate-targeted lipid mesophases, cubosomes (CUB) and hexosomes (HEX), loaded with doxorubicin (DOX). Three cancer-derived cell lines (KB, HeLa, T98G) exhibiting different expressional levels of folate receptor protein...
-
Expedited constrained multi-objective aerodynamic shape optimization by means of physics-based surrogates
PublicationIn the paper, computationally efficient constrained multi-objective design optimization of transonic airfoil profiles is considered. Our methodology focuses on fixed-lift design aimed at finding the best possible trade-offs between the two objectives: minimization of the drag coefficient and maximization of the pitching moment. The algorithm presented here exploits the surrogate-based optimization principle, variable-fidelity computational...
-
Mechanism of Binding of Antifungal Antibiotic Amphotericin B to Lipid Membranes: An Insight from Combined Single-Membrane Imaging, Microspectroscopy, and Molecular Dynamics
PublicationAmphotericin B is a lifesaving polyene antibiotic used in the treatment of systemic mycoses. Unfortunately, the pharmacological applicability of this drug is limited because of its severe toxic side effects. At the same time, the lack of a well-defined mechanism of selectivity hampers the efforts to rationally design safer derivatives. As the drug primarily targets the biomembranes of both fungi and humans, new insights into the...
-
A comprehensive evaluation of flexible FDM/FFF 3D printing filament as a potential material in medical application
PublicationThe use of FDM/FFF in 3D printing for medical sciences is becoming common. This is due to the high availability and decent price of both 3D printers and filaments useful for FDM/FFF. Currently, researchers' attention is focused mainly on the study of medical filaments based on PLA, PCL or their modifications. This contributes to insufficient diversity of medical-grade filaments on the market. Moreover, due to the lack of specified...
-
Synthesis, spectroscopy and computational studies of some biologically important hydroxyhaloquinolines and their novel derivatives
PublicationA series crystalline compounds of methyl and phosphinyl derivatives of 2-methylquinolin-8-ol (1a) and related 5,7-dichloro-2-methylquinolin-8-ol (1b) were quantitatively prepared and characterized by microanalysis, IR, UV-vis and multinuclear NMR spectroscopy. Five of them have been characterized by single crystal X-ray diffraction method. The known compounds, 8-methoxy-2-methylquinoline (2a) and 8-methoxyquinoline (2d), were synthesised...
-
Impact of rotor geometry optimization on the off-design ORC turbine performance
PublicationThe paper describes the method of CFD based Nelder-Mead optimization of a 10 kW single-stage axial turbine operating in an ORC system working on R7100. The total-to-static isentropic efficiency is defined as an objective function. Multi-point linear regression is carried out to determine the significance of the objective function arguments and to pick up the set of particular variables and characteristic quantities (e.g. flow angles)...
-
Simple Millimeter Wave Identification System Based on 60 GHz Van Atta Arrays
PublicationThe paper presents a proof-of-concept of a millimeter-wave identification system based on Van Atta array tags in the 60 GHz band. For interrogation of the tags, a vector network analyzer and a measurement transceiver were employed in alternative test configurations. The design, fabrication and measurements of co- and cross-polarized Van Atta arrays are presented in the paper. They can be treated as simple chipless RFID tags with...
-
The Optical Coherence Tomography and Raman Spectroscopy for Sensing of the Bone Demineralization Process
PublicationThe presented research was intended to seek new optical methods to investigate the demineralization process of bones. Optical examination of the bone condition could facilitate clinical trials and improve the safety of patients. The authors used a set of complementary methods: polarization-sensitive optical coherence tomography (PS-OCT) and Raman spectroscopy. Chicken bone samples were used in this research. To stimulate in laboratory...
-
Assessment of dynamic characteristics of thin cylindrical sandwich panels with magnetorheological core
PublicationBased on the equivalent single-layer linear theory for laminated shells, free and forced vibrations of thin cylindrical sandwich panels with magnetorheological core are studied. Five variants of available magnetorheological elastomers differing in their composition and physical properties are considered for smart viscoelastic core. Coupled differential equations in terms of displacements based on the generalized kinematic hypotheses...
-
A Method of Fast and Simultaneous Calibration of Many Mobile FMCW Radars Operating in a Network Anti-Drone System
PublicationA market for small drones is developing very fast. They are used for leisure activities and exploited in commercial applications. However, there is a growing concern for accidental or even criminal misuses of these platforms. Dangerous incidents with drones are appearing more often, and have caused many institutions to start thinking about anti-drone solutions. There are many cases when building stationary systems seems to be aimless...
-
Effects of the Origin and Deacetylation Degree of Chitosan on Properties of Its Coatings on Titanium
PublicationThe properties of chitosan coatings on titanium surfaces may be influenced by a variety of factors, including their chemical characteristics and the deposition method. The aim of this research was to determine the influence of a chitosan’s origin (a type of shrimp) and deacetylation degree (DD), when deposited on a very smooth titanium surface, on adhesion and biological behavior. The tests were performed using chitosan of a degree...
-
Low energy elastic scattering of electrons from hexafluoropropene (C3F6)
PublicationWe present cross sections from a joint experimental and theoretical study on elastic electron scattering from hexafluoropropene (C3F6) in the gas phase. The experimental results, using low energy electron spectroscopy, were obtained at incident electron energies of 0.5, 1, 1.5, 2, 3, 4, 5, 6, 10, 12, 15 and 20 eV, for scattering angles ranging from 10°to 130°. The theoretical method used in the computation of the integral, momentum...
-
Tuning of the Electrochemical Properties of Transparent Fluorine-doped Tin Oxide Electrodes by Microwave Pulsed-plasma Polymerized Allylamine
PublicationWe report here the dry, one-step, and low-temperature modification of FTO surfaces using pulsed plasma polymerization of allylamine (PPAAm). PPAAm/FTO surfaces were characterized by X-ray photoelectron spectroscopy, spectroscopic ellipsometry, and contact angles to understand the morphological, structural, and optical properties. FTO were coated with a very thin layer of adherent cross-linked, pinhole-, and additive-free allylamine...
-
Systematics of intelligent transport systems services
PublicationRecent years have seen a more intensified deployment of Intelligent Transport Systems (ITS) in Polish cities. Work is also underway on the implementation of ITS on the national roads within the National Traffic Management System (KSZR). The research project RID-4D (part of Road Innovations), is designed to fill the gap, which is the lack of systematics of ITS services in Poland. The paper presents a proposal of ITS services systematics,...
-
Influence of excitons interaction with charge carriers on photovoltaic parameters in organic solar cells
PublicationWe report on theoretical analysis of excitons annihilation on charge carriers in organic solar cells. Numerical calculations based on transient one-dimensional drift-diffusion model have been carried out. An impact of three quantities (an annihilation rate constant, an exciton mobility and a recombination reduction factor) on current density and concentrations of charge carriers and excitons is investigated. Finally, we discuss...
-
Experimental Study of the Influence of Noise Level on the Uncertainty Value in a Measurement System Containing an Analog-to-Digital Converter
Open Research DataFor newly developed measuring systems it is easy to estimate type B uncertainties based on the technical data of the measuring modules applied. However, it is difficult to estimate A type un-certainties due to the unknown type and level of interferences infiltrating into the measuring sys-tem. This is a particularly important problem for measurements...
-
The dataset of coupling coefficients for rotating receiver of multicoil dynamic wireless power transfer system
Open Research DataThe provided dataset is part of the simulation results shown in related journal paper "Optimal Rotating Receiver Angles Estimation for Multicoil Dynamic Wireless Power Transfer".
-
Tensile modulus of human orbital wall bones cut in sagittal and coronal planes
PublicationIn the current research, 68 specimens of orbital superior and/or medial walls taken from 33 human cadavers (12 females, 21 males) were subjected to uniaxial tension untill fracture. The samples were cut in the coronal (38 specimens) and sagittal (30 specimens) planes of the orbital wall. Apparent density (ρapp), tensile Young’s modulus (E-modulus) and ultimate tensile strength (UTS) were identified. Innovative test protocols were...
-
Long Distance Geographically Distributed InfiniBand Based Computing
PublicationCollaboration between multiple computing centres, referred as federated computing is becom- ing important pillar of High Performance Computing (HPC) and will be one of its key components in the future. To test technical possibilities of future collaboration using 100 Gb optic fiber link (Connection was 900 km in length with 9 ms RTT time) we prepared two scenarios of operation. In the first one, Interdisciplinary Centre for Mathematical...
-
The experimental results of diesel fuel spray with marine engine injector
Open Research DataThe data set presents the measurement of the diesel fuel spray from with marine engine injector. The main target presents results is a study of the time course of macro parameters (spray tip penetration, spray cone angle) of fuel spray in the cylinder of marine diesel engine. The impact of ambient conditions and the geometrical parameters of the injector...
-
Effect of package type on selected parameters of nutritional quality of chill-stored white sauerkraut
PublicationBrassica vegetables, including white cabbage, both fresh and sour (Brassica oleracea L. var. capitata L.), contain a lot of valuable metabolites which are effective in chemoprevention of cancer as documented by numerous studies. This work investigates the effect of different packaging types; low density polyethylene (PE-LD) and metalized polyethylene terephthalate (PET met/PE) with polyethylene bags on selected quality parameters in...
-
The performance of H2O, R134a, SES36, ethanol, and HFE7100 two-phase closed thermosyphons for varying operating parameters and geometry
PublicationIn this study, the influences of different parameters at performance two-phase closed thermosiphon (TPCT) was presented. It has been confirmed that the working fluid, as well as operating parameters and fill ratio, are very important factors in the performance of TPCT. The article shows characteristics of gravitational tube geometr ies, as well as the technical characteristic of the most important system components, i.e., the evaporator/condenser....
-
Thermo-Chemical Decomposition Study of Polyurethane Elastomer Through Glycerolysis Route with Using Crude and Refined Glycerine as a Transesterification Agent
PublicationDue to the increasing amount of polyurethane waste, chemical recycling of these materials is a topic of growing interest for many researchers. The primary pur- pose of polyurethane feedstock recycling is to recover the starting polyol. In this study glycerolysis using glycerine from two sources and two purity grades is proposed as a method of chemical recycling. The main effort of this paper focuses on the employment of commercial...
-
Vibrational Sum-Frequency Generation Activity of a 2,4-Dinitrophenyl Phospholipid Hybrid Bilayer: Retrieving Orientational Parameters from a DFT Analysis of Experimental Data
PublicationThe vibrational nonlinear activity of films of 2,4-dinitrophenyl phospholipid (DNP) at the solid interface is measured by sum-frequency generation spectroscopy (SFG). Hybrid bilayers are formed by a LangmuirSchaefer approach in which the lipid layer is physisorbed on top of a self-assembled monolayer of dodecanethiol on Pt with the polar heads pointing out from the surface. The SFG response is investigated in two vibrational frequency...
-
Identyfikacja ryzyka zakłóceń logistycznych podczas planowania procesu inwestycyjnego na wybranym przykładzie
PublicationDziałania logistyczne w budownictwie obejmują przede wszystkim przepływ informacji, lokalizację zakładów produkcyjnych i magazynów na placu budowy, transport i składowanie materiałów budowlanych, realizowanie zamówień, procesy zaopatrzeniowe, kontrolę zapasów, czynności reparacyjne i zaopatrywanie w części maszyn budowlanych. Zdarzenia losowe, które mogą zaistnieć i przerwać bądź przedłużyć wyżej wymienione prace nie są łatwe do...
-
Compact Electromagnetic Lens Antennas Using Cascaded Metasurfaces for Gain Enhancement and Beam Steering Applications
PublicationElectromagnetic (EM) lens antenna designs using cascaded metasurfaces for gain enhancement and beam steering applications are proposed. Two different lens aperture designs are proposed and populated with aperiodic unit cells of size 0.2λo × 0.2λo. In lens Design 1, the unit cells of different phases are distributed in concentric circular zones, whereas in lens Design 2, the unit cells of different phases are distributed in vertical...
-
Overview of Metamaterials-Integrated Antennas for Beam Manipulation Applications: The Two Decades of Progress
PublicationMetamaterials (MMs) are synthetic composite structures with superior properties not found in naturally occurring materials. MMs have gained massive attention over the last two decades because of their extraordinary properties, such as negative permittivity and permeability. These materials enable many applications in communication subsystems, especially in the field of antenna design, to enhance gain, bandwidth, and efficiency,...
-
Financial Markets and Bankruptcy Systems: Is there a Relationship?
PublicationPurpose: Filling the cognitive gap in the theory of ex-post transaction costs, i.e., at the stage of enforcing market transactions by examining the relationship between friendliness/severity of the bankruptcy and restructuring law towards debtors, the level of development of financial markets, the effectiveness of the judicial system and the rate of debt recovery. Design/Methodology/Approach: In the research, the following methods...
-
Corporate Entrepreneurship: A Literature Review and Future Research Perspectives
PublicationBackground. Nowadays, corporate entrepreneurship (CE) is perceived as an essential approach to boost the innovation and creativity within existing organizations for achieving higher opportunities in the market. This paper examines this concept, which has been largely discussed in the Anglo-Saxon world over the last thirty years. Like for many other phenomena, also in case of CE, this discussion has provided numerous conceptualizations,...
-
Exploring novel Cd(ii) complexes with 5-methyl-4-imidazolecarboxaldehyde: synthesis, structure, computational insights, and affinity to DNA through switchSense methodology
PublicationA series of four Cd(II) complexes with 5-methyl-4-imidazolecarboxaldehyde (L) with different inorganic anions within or outside the coordination sphere of general formula: [CdCl2 L2 ] (1), [CdBr2 L 2] (2), [CdI2L 2] (3), and [CdL4 ](PF6 )2 ·3H2 O (4) was synthesized through one-step and two-step reactions, respectively. All complexes were obtained as colorless crystals without the need for recrystallization and exhibited solubi- lity...
-
Wieczór pamięci prof. Jacka Namieśnika
EventsPolitechnika Gdańska i Stowarzyszenie Absolwentów PG zapraszają 19.05.2019 r. do Akademickiego Klubu PG „KWADRATOWA” na wieczór poświęcony pamięci prof. Jacka Namieśnika, śp. rektora Politechniki Gdańskiej.
-
E-experiments in physics. Proper business process management, collaborative development process and project management guidance – remedy for avoiding the main IT project’s failure
PublicationOnly a few of learning aids and simulations of physical phenomena allow for building interactive experiments; experiments similar to those that should be conducted in physics laboratories at schools. Group of staff from Gdansk University of Technology decided to fill this market niche by designing and constructing a set of virtual experiments – so called e-experiments. To avoid common problems that a lot of IT products brought...
-
Bridge Ergonomic Design: A Review
PublicationHuman error remains the most common cause of marine incidents and it is worth emphasizing that navigator’s performance is directly affected by ergonomic factors on the bridge. Studies regarding influence of bridge design and work environment on the operator are rare, thus the main purpose of this paper is to fill in this gap. Documents issued by recognized organizations, research publications and additional sources were reviewed...
-
Side Effects of National Immunization Program: E-Governance Support Toward Elders' Digital Inclusion
PublicationIn response to the coronavirus pandemic, the European Union (EU) governments develop policies to regulate exclusive health protection actions that consider societal needs with the emphasis on elders. Given that the EU vaccination strategy uses a centralized ICT-based approach, there is little guidance on how seniors are included in national immunization programs (NIP). In this paper, we addressed a knowledge gap of the side effects...
-
Good practices in requirements, project and risk managment in educational IT projects
PublicationOne can find many learning aids and simulations of physical phenomena on the market - provided as a standalone application or as part of an educational package. However, only a few of them allow for the building of interactive experiments: experiments similar to those that should be conducted in physics laboratories at schools. Gdańsk University of Technology decided to fill this market niche by designing and constructing a set...
-
2-Coloring number revisited
Publication2-Coloring number is a parameter, which is often used in the literature to bound the game chromatic number and other related parameters. However, this parameter has not been precisely studied before. In this paper we aim to fill this gap. In particular we show that the approximation of the game chromatic number by the 2-coloring number can be very poor for many graphs. Additionally we prove that the 2-coloring number may grow...
-
Application Of Generative Adversarial Network for Data Augmentation and Multiplication to Automated Cell Segmentation of the Corneal Endothelium
PublicationConsidering the automatic segmentation of the endothelial layer, the available data of the corneal endothelium is still limited to a few datasets, typically containing an average of only about 30 images. To fill this gap, this paper introduces the use of Generative Adversarial Networks (GANs) to augment and multiply data. By using the ``Alizarine'' dataset, we train a model to generate a new synthetic dataset with over 513k images....
-
Laboratory assessment of permeability of sand and biopolymer mixtures
PublicationLaboratory assessment of permeability of sand and biopolymer mixtures. This research presents a method of creating seepage barriers in a sandy soil using biopolymer additives (biosubstance), which consist of polysaccharides and water. Polysaccharides strongly interact with water to produce a viscous suspension. The paper aims to investigate the infl uence of a biosubstance employed in a highly permeable sandy soil. Amount of the...
-
Seafloor characterisation using multibeam data: sonar image properties, seabed surface properties and echo properties
PublicationIn the paper, the approach to seafloor characterisation is presented. The multibeam sonars, besides their well verified and widely used applications like high resolution bathymetry and underwater object detection and imaging, are also the promising tool in seafloor characterization and classification, having several advantages over conventional single beam echosounders. The proposed approach relies on the combined, concurrent use...
-
Synthesis and characterization of cycloaliphatic hydrophilic polyurethanes, modified with l-ascorbic acid, as materials for soft tissue regeneration
PublicationIn this paper we described synthesis and characteristic of obtained hydrophilic polyurethanes (PURs) modified with ascorbic acid (commonly known as vitamin C). Such materials may find an application in the biomedical field, for example in the regenerative medicine of soft tissues, according to ascorbic acid wide influence on tissue regeneration Flora (2009), Szymańska-Pasternak et al. (2011), Taikarimi and Ibrahim (2011), Myrvik...