Search results for: SYNOVIAL FLUID
-
MODELOWANIE TURBINY WIATROWEJ Z DWOMA PRZECIWBIEŻNIE OBRACAJĄCYMI SIĘ WIRNIKAMI
PublicationW artykule przedstawiono sposoby modelowania dwuwirnikowej turbiny wiatrowej z wykorzystaniem technik Obliczeniowej Mechaniki Płynów. Omówiono uproszczone metody modelowania Actuator Disc i Actuator Line Method oraz aspekty związane z dokładnym odwzorowaniem turbiny na siatce obliczeniowej. Zaprezentowano przykładowe wyniki obliczeń turbiny dwuwirnikowej złożonej z wirników NREL o mocy nominalnej 5 MW każdy. Do wykonania badań...
-
Multi-fidelity aerodynamic design trade-off exploration using point-by-point Pareto set identification
PublicationAerodynamic design is inherently a multi-objective optimization (MOO) problem. Determining the best possible trade-offs between conflicting aerodynamic objectives can be computationally challenging when carried out directly at the level of high-fidelity computational fluid dynamics simulations. This paper presents a computationally cheap methodology for exploration of aerodynamic design trade-offs. In particular, point-by-point...
-
Identification of Emotional States Using Phantom Miro M310 Camera
PublicationThe purpose of this paper is to present the possibilities associated with the use of remote sensing methods in identifying human emotional states, and to present the results of the research conducted by the authors in this field. The studies presented involved the use of advanced image analysis to identify areas on the human face that change their activity along with emotional expression. Most of the research carried out in laboratories...
-
Reservoir Influence on Pressure Wave Propagation in Steel Pipes
PublicationThe relation between the length of steel pipe and the pressure wave period in the system, reservoir-pipe-valve, is discussed. Experiments carried out for the short steel pipes showed that in such a system, the pressure wave celerity estimated using the measured wave cycles systematically increases with the increase of the pipe length. The observed differences can exceed even 90 m=s. As the pressure wave traveling in the pipe with...
-
Variable-fidelity CFD models and co-Kriging for expedited multi-objective aerodynamic design optimization
PublicationPurpose – Strategies for accelerated multi-objective optimization of aerodynamic surfaces are investigated, including the possibility of exploiting surrogate modeling techniques for computational fluid dynamic (CFD)-driven design speedup of such surfaces. The purpose of this paper is to reduce the overall optimization time. Design/methodology/approach – An algorithmic framework is described that is composed of: a search space reduction,...
-
Extended micropolar approach within the framework of 3M theories and variations thereof
PublicationAs part of his groundbreaking work on generalized continuum mechanics, Eringen proposed what he called 3M theories, namely the concept of micromorphic, microstretch, and micropolar materials modeling. The micromorphic approach provides the most general framework for a continuum with translational and (internal) rotational degrees of freedom (DOF), whilst the rotational DOFs of micromorphic and micropolar continua are subjected...
-
Diagnostic Accuracy of Liquid Biopsy in Endometrial Cancer
PublicationBackground: Liquid biopsy is a minimally invasive collection of a patient body fluid sample. In oncology, they offer several advantages compared to traditional tissue biopsies. However, the potential of this method in endometrial cancer (EC) remains poorly explored. We studied the utility of tumor educated platelets (TEPs) and circulating tumor DNA (ctDNA) for preoperative EC diagnosis, including histology determination. Methods:...
-
Aerodynamic Shape Optimization for Delaying Dynamic Stall of Airfoils by Regression Kriging
PublicationThe phenomenon of dynamic stall produce adverse aerodynamic loading which can adversely affect the structural strength and life of aerodynamic systems. Aerodynamic shape optimization (ASO) provides an effective approach for delaying and mitigating dynamic stall characteristics without the addition of auxiliary system. ASO, however, requires multiple evaluations time-consuming computational fluid dynamics models. Metamodel-based...
-
Coupling between Blood Pressure and Subarachnoid Space Width Oscillations during Slow Breathing
PublicationThe precise mechanisms connecting the cardiovascular system and the cerebrospinal fluid (CSF) are not well understood in detail. This paper investigates the couplings between the cardiac and respiratory components, as extracted from blood pressure (BP) signals and oscillations of the subarachnoid space width (SAS), collected during slow ventilation and ventilation against inspiration resistance. The experiment was performed on...
-
Effect of annealing temperature on slurry erosion resistance of ferritic X10CrAlSi18 steel
PublicationIn the present work, the slurry erosion tests were carried out to investigate the influence of heat treatment on slurry erosion process of ferritic X10CrAlSi18 stainless steel using a slurry pot test rig. X10CrAlSi18 stainless steel was tested in as-received condition and after annealing at three different temperatures: 600°C, 800°C and 1000°C. Degradation of materials due to slurry erosion depends on many factors connected with...
-
Biomimetics in Fluid Mechanics with practical application using CFD, S-30, WIMiO, Energetyka, II st., sem. 03, stacjonarne, (PG_00060130), semestr letni 2022/2023
e-Learning CoursesWykład wprowadza do procesu biomimetycznego, systematycznej procedury mającej na celu wykorzystania w technice rozwiązań z natury. Szczególny nacisk położony jest na zastosowania w mechanice płynów.
-
Numerical Methods
e-Learning CoursesNumerical Methods: for Electronics and Telecommunications students, Master's level, semester 1 Instructor: Michał Rewieński, Piotr Sypek Course description: This course provides an introduction to computational techniques for the simulation and modeling of a broad range of engineering and physical systems. Concepts and methods discussed are widely illustrated by various applications including modeling of integrated circuits,...
-
Nowe możliwości generowania zarysów satelitowych mechanizmów roboczych
PublicationPlanetary hydraulic gear motors have been well known since 70's . first motors were constructed for maritime industry by hydroster from gdansk. the evolution of this type of motors led to an increase of nominal pressure and durability. nowadays the industry needs reliable and efficient motor able to work with alternative hydraulic fluids like water, emulsion and vegetable oil. therefore a new type of motors are being developed...
-
Determination of isoprostanes in exhaled breath condensate samples by liquid chromatography coupled with tandem mass spectrometry
PublicationOxidative stress (OS) is a state of imbalance between continuously generating reactive oxygen species (ROS) during normal cell metabolism and mechanism of detoxifying oxygen radicals through a network of antioxidative enzymes. Isoprostanes are prostaglandin -like substances that are produced in vivo primarily by free radical-induced peroxidation of arachidonic acid. The measurement of isoprostanes in biological fluids and/or tissue...
-
Computer Supported Analysis of the Human Body Surface Area
PublicationRecent scientific studies show the growing importance of the coefficients: BSA and TBSA, as an alternative to the widely used BMI. The relevant indicators are widely used in medicine, including such areas as: the treatment of burns, chemotherapy, dermatology and toxicology; as benchmarks when calculating doses of drugs and fluids. The particular problems concerning this subject are: the change of the reference parameter value which...
-
Metodyka badań rozwojowych nowego typu silników i pomp satelitowych
PublicationResearch and development of new type satellite motors and satellite pumps SM with small geometrical displacement, from 5 to 73 cm3/rev, has been conducted in cooperation with Stosowanie Maszyn company from Katowice (manufacturer of motors and pump SM). The improvement of construction of those machines, especially construction of axial compensation and construction of fluid distribution channels have been the main problem of research...
-
Numerical Study of the Impinging Jets Formed by an Injector with Different Nozzle Diameters
PublicationThe collision of two or more liquid jets may provide considerable atomisation and efficient mixing of injected substances at the same time. This phenomenon is used, among others, in rocket engines, where the fuel and oxidiser are introduced separately and almost immediately mixed through self-impingement. Depending on the injection and operating conditions, diverse configurations of impinging jets are used, such as doublets,...
-
Air trapping problem during infiltration on the large areas
PublicationThe process of flow modeling in unsaturated porous medium is often found in many fields of sciences: geology, fluid mechanics, thermodynamics, microbiology or chemistry. Problem is relatively complicated due to complexity of the system which contains three phases: water, air and soil skeleton. The flow of water in such a medium can be described using two-phase (2PH) flow formulation, which accounts the inflow of air and water phases,...
-
Porous structures in aspects of transpirating cooling of oxycombustion chamber walls
PublicationA wet oxycombustion chamber, which must be effectively cooled due to high temperature evolved during the oxy-combustion process, by using the phenomena of Reynolds thermal transpiration and Navier slip velocity. Closures needed to execute mass flow rate in a microchannel, which should be treated as a single porous structure in the walls of the combustion chamber, have been obtained by applying a local 3D approach. The Navier-Stokes...
-
Numerical Study on Mitigation of Flow Maldistribution in Parallel Microchannel Heat Sink: Channels Variable Width Versus Variable Height Approach
PublicationMicrochannel heat sink on one hand enjoys benefits of intensified several folds heat transfer performance but on the other hand has to suffer aggravated form of trifling limitations associated with imperfect hydrodynamics and heat transfer behavior. Flow maldistribution is one of such limitation that exaggerates temperature nonuniformity across parallel microchannels leading to increase in maximum base temperature. Recently, variable...
-
Fast Multi-Objective Aerodynamic Optimization Using Sequential Domain Patching and Multifidelity Models
PublicationExploration of design tradeoffs for aerodynamic surfaces requires solving of multi-objective optimization (MOO) problems. The major bottleneck here is the time-consuming evaluations of the computational fluid dynamics (CFD) model used to capture the nonlinear physics involved in designing aerodynamic surfaces. This, in conjunction with a large number of simulations necessary to yield a set of designs representing the best possible...
-
Experimental study on the feasibility of alternative materials for tilting pad thrust bearings operating in transition to mixed friction
PublicationIn hydrodynamic bearings traditional bearing alloys: Babbitts and bronzes are most frequently utilized. Polymer sliding layers are sometimes applied as a valuable alternative. Hard diamond-like carbon (DLC) coatings, which are also considered for certain applications may show some advantages, as well. Although material selection is of secondary importance in a full film lubrication regime it becomes important in mixed friction...
-
Comparative analysis of mechanical conditions in bone union following first metatarsophalangeal joint arthrodesis with varied locking plate positions: A finite element analysis
PublicationFirst metatarsophalangeal joint arthrodesis is a typical medical treatment performed in cases of arthritis or joint deformity. The gold standard for this procedure is arthrodesis stabilisation with the dorsally positioned plate. However, according to the authors’ previous studies, medially positioned plate provides greater bending stiffness. It is worth to compare the mechanical conditions for bone formation in the fracture callus...
-
Multi-fidelity robust aerodynamic design optimization under mixed uncertainty
PublicationThe objective of this paper is to present a robust optimization algorithm for computationally efficient airfoil design under mixed (inherent and epistemic) uncertainty using a multi-fidelity approach. This algorithm exploits stochastic expansions derived from the Non-Intrusive Polynomial Chaos (NIPC) technique to create surrogate models utilized in the optimization process. A combined NIPC expansion approach is used, where both...
-
Effect of oxidation and in vitro intestinal hydrolysis on phospholipid toxicity towards HT29 cell line serving as a model of human intestinal epithelium
PublicationOxidation of food-derived phospholipids (PLs) can influence nutrient digestion and induce oxidative stress in gastrointestinal epithelium. In this study, hen egg yolk PL fraction was used to evaluate the effect of lipoxygenase (LOX)-induced PL oxidation on the rate of PL hydrolysis catalyzed by pancreatic phospholipase A2 (PLA2) in the presence of bile salts (BSs). Then, PL/BS solutions containing native or oxidized PLs were used...
-
Thermal Energy Storage with PCMs in Shell-and-Tube Units: A Review
PublicationThe paper presents a survey of the experimental and numerical studies of shell-and-tube systems in which phase change material (PCM) is used. Due to the multitude of design solutions for shell-and-tube systems, the emphasis is placed on double-tube (DT), triplex-tube (TT), and multitube (MT) units. Additionally, only single-pass systems are considered. Particular attention is paid to the method of heat transfer intensification....
-
Application of the ISE Optimized Proportional Control of the Wave Maker in a Towing Tank
PublicationThis paper presents the improvement of the wave maker control system. The wave maker is a facility widely used in hydromechanics laboratories to generate waves in towing tanks. It is equipped with an electrohydraulic drive and an actuator submerged into water. The waves are generated to model the environmental conditions for physical experiments, performed on reduced-scale models of maritime objects. The physical experiments allow...
-
Multi-objective optimization of the cavitation generation unit structure of an advanced rotational hydrodynamic cavitation reactor
PublicationHydrodynamic cavitation (HC) has been widely considered a promising technique for industrial-scale process intensifications. The effectiveness of HC is determined by the performance of hydrodynamic cavitation reactors (HCRs). The advanced rotational HCRs (ARHCRs) proposed recently have shown superior performance in various applications, while the research on the structural optimization is still absent. The present study, for the...
-
A shear stress micromodel of urinary tract infection by the Escherichia coli producing Dr adhesin
PublicationIn this study, we established a dynamic micromodel of urinary tract infection to analyze the impact of UT-segment-specific urinary outflow on the persistence of E. coli colonization. We found that the adherence of Dr+ E. coli to bladder T24 transitional cells and type IV collagen is maximal at lowest shear stress and is reduced by any increase in flow velocity. The analyzed adherence was effective in the whole spectrum of physiological...
-
Investigation on polypropylene friction stir joint: effects of tool tilt angle on heat flux, material flow and defect formation
PublicationTool tilt angle (TTA) is a critical factor that can control material flow in polymeric materials' friction stir joining (FSJ). This study selected a TTA range between 0° to 4° for FSJ of polypropylene (PP) polymer sheet. A modified computational fluid dynamic (CFD) technique was implemented to gain a deep understanding of the effects of TTA during FSJ of PP. The PP joint's internal flow, defect formation, heat generation, and tensile...
-
A Concept for Safe and Less Expensive Acceleration of a Marine Steam Turbine Start-up
PublicationThis paper analyses the issue of accelerated start-up of a marine steam turbine, which is an important problem because the start-up of a steam machine involves the combustion of fuel that is not transformed into useful energy. To find novel technologies that offer improvements in this aspect is essential due to restrictions on reducing ship emissions. Thus, the shorter the start-up time, the better for the environment and economy....
-
Temperature Evolution, Material Flow, and Resulting Mechanical Properties as a Function of Tool Geometry during Friction Stir Welding of AA6082
PublicationThe friction stir welding process was simulated for joining AA6082 aluminum alloy with the use of the computational fluid dynamics method. Two different tool geometries were used—a tapered cylindrical pin (simple pin) and a hexagonal pin with grooves (complex pin). The analysis of the simulations performed was discussed in terms of temperature evolution during the process, total heat input, residual stresses and material flow....
-
Cu-HKUST-1 and Hydroxyapatite–The Interface of Two Worlds toward the Design of Functional Materials Dedicated to Bone Tissue Regeneration
PublicationA novel composite based on biocompatible hydroxyapatite (HA) nanoparticles and Cu-HKUST-1 (Cu-HKUST-1@HA) has been prepared following a layer-by-layer strategy. Cu-HKUST-1 was carefully selected from a group of four Cu-based metal−organic frameworks as the material with the most promising antimicrobial activity. The formation of a colloidal Cu- HKUST-1 layer on HA nanoparticles was confirmed by various techniques, e.g., infrared...
-
Green adsorbents and solvents in food analysis
PublicationGreen analytical chemistry aims to minimize the negative impact of analytical procedures on the environment and human health. This can be achieved through the use of non-toxic and environmentally friendly reagents. Classical green solvents include water, ethanol, acetone, and supercritical fluids. Water has been used for the extraction of water-soluble compounds (sugars, amino acids). Ethanol and acetone have been used for the...
-
Structure-rheology relationship of fully bio-based linear polyester polyols for polyurethanes - Synthesis and investigation
PublicationThe synthesis of polyols from renewable substances as an alternative for petrochemical-based polyols play important matter in the polyurethane industry. In this work, the fully bio-based linear polyester polyols with different catalyst amounts were synthesized via two-step polycondensation method. The effect of various catalyst content on the structure and rheological behavior were established. Fourier Transform Infrared Spectroscopy,...
-
A New Approach to Chemical Recycling of Polyamide 6.6 and Synthesis of Polyurethanes with Recovered Intermediates
PublicationA new efficient method for the chemical decomposition of polyamide 6.6 by the glycolysis and amino-glycolysis processes was proposed. The glycolysis was conducted using the mass excess of ethylene glycol (EG) as a decomposing agent in the presence of a catalyst. Also, a mixture of EG and triethylenetetramine was used as another decomposing agent in the amino- glycolysis process. The described process of decomposition did not...
-
Simultaneous determination of Na+, K+, Ca2+, Mg2+ and Cl- in unstimulated and stimulated human saliva using all solid state multisensor platform
PublicationHuman saliva is one of the body fluids which collection method is relatively simple and non-invasive. The article is dedicated to assess concentration (activity) of Na+, K+, Ca2+, Mg2+ and Cl- in fresh, unstimulated or stimulated human saliva samples using single solid contact ion-selective electrodes with conventional reference electrode and self-made multisensor platform (MP) equipped with ion-selective membranes for Na+, K+,...
-
The occurence and diagnosis of biomarkers of ethyl alcohol consumption
PublicationEthyl alcohol is a legal and a widely available psychoactive drug. However, its excessive consumption causes addiction. This leads to aggressive behaviors, family battery, difficulties in interpersonal relations, legal offences, suicides, car accidents and deterioration in labor productivity, what causes financial problems. Despite many social actions against alcohol consumption, this problem is still unresolved. Therefore, fast...
-
Influence of metallic porous microlayer on pressure drop and heat transfer of stainless steel plate heat exchanger
PublicationThe experimental analysis of passive heat transfer intensification in the case of plate heat exchanger has been carried out. The metallic porous layer was created on the heat transfer surface of analyzed unit. The experiment was accomplished in two stages. In the first stage the commercial stainless steel gasketed plate heat exchanger was investigated, while in the second one – the identical heat exchanger but with the modified...
-
Thermal performance of a prototype plate heat exchanger with minichannels under boiling conditions
PublicationTo solve the problem and to meet the requirements of customers in the field of high heat fluxes transfer in compact units, a new design of plate heat exchanger with minichannels (minichannels PHE) was proposed. The aim was to construct a compact heat exchanger of high effectiveness for the purpose of household cogeneration ORC system. In this paper the experimental analysis of an assembled prototype of such compact heat exchanger...
-
Silicon’s Influence on Polyphenol and Flavonoid Profiles in Pea (Pisum sativum L.) under Cadmium Exposure in Hydroponics: A Study of Metabolomics, Extraction Efficacy, and Antimicrobial Properties of Extracts
PublicationThe current study aimed to investigate the impact of silicon (Si) supplementation in the form of Na2SiO3 on the metabolome of peas under normal conditions and following exposure to cadmium (Cd) stress. Si is known for its ability to enhance stress tolerance in various plant species, including the mitigation of heavy metal toxicity. Cd, a significant contaminant, poses risks to...
-
Mitigation effect of face shield to reduce SARS-CoV-2 airborne transmission risk: Preliminary simulations based on computed tomography
PublicationWe aimed to develop a model to quantitatively assess the potential effectiveness of face shield (visor) in reducing airborne transmission risk of the novel coronavirus SARS-CoV-2 during the current COVID-19 pandemic using the computational fluid dynamics (CFD) method. The studies with and without face shield in both an infected and healthy person have been considered in indoor environment simulation. In addition to the influence...
-
COMPARISON OF PREDICTIVE METHODS FOR FLOW BOILING HEAT TRANSFER IN CONVENTIONAL CHANNELS AND MINICHANNELS – THE EFFECT OF REDUCED PRESSURE
PublicationIn the paper are presented the results of follow on studies from [1]–[3] using authors own model to predict heat transfer coefficient during flow boiling. The model has been tested against a large selection of experimental data collected from various researchers to investigate the sensitivity of the in-house developed model. The collected experimental data came from various studies from literature and were conducted for the full...
-
Synthesis, characterization, and interactions of single-walled carbon nanotubes modified with doxorubicin with Langmuir–Blodgett biomimetic membranes
PublicationThe synthesis, characterization, and the influence of single-walled carbon nanotubes (SWCNTs) modified with an anticancer drug doxorubicin (DOx) on the properties of model biological membrane as well as the comparison of the two modes of modification has been presented. The drug was covalently attached to the nanotubes either preferentially on the sides or at the ends of the nanotubes by the formation of hydrazone bond. The efficiency...
-
Flow maldistribution and its mitigation in mini heat exchangers
PublicationIn the present paper, a detailed numerical investigation has been carried out to analyze the flow maldistribution in 50 parallel 1 mm x 1 mm rectangular minichannels and 1 mm depth minigap section with rectangular, trapezoidal, triangular or concave mani-folds in Z-type flow configuration (16 different cases). The working medium was ethanol and the mass flow rate was 5×10-4 kg/s. Both sections was heated from the bottom side. Heat...
-
Numerical model for thin liquid film with evaporation and condensation on solid surfaces in systems with conjugated heat transfer
PublicationCondensation and evaporation processes from wetted surfaces are of utmost importance in many technological or industrial applications. In many devices such as home-appliances and air conditioning systems just to name a few, condensation and evaporation processes greatly impact their performance and energy efficiency; The physics of these processes is quite complex, involving conjugate heat transfer among solid–liquid film-gaseous...
-
New Materiality-towards ‘Media Environments
PublicationArticle presents media solutions providing new materiality of architectural spaces. Media solutions in architecture evolve in new forms. Articlepresentsboth the developmentof new technological solutionsas well as new ways of application of media solutions in relation toarchitectural form. The aim of the article is to show technical aspects of new materiality - intelligent materials, allowing transmission of changeable visual content...
-
Fast Low-fidelity Wing Aerodynamics Model for Surrogate-Based Shape Optimization
PublicationVariable-fidelity optimization (VFO) can be efficient in terms of the computational cost when compared with traditional approaches, such as gradient-based methods with adjoint sensitivity information. In variable-fidelity methods, the directoptimization of the expensive high-fidelity model is replaced by iterative re-optimization of a physics-based surrogate model, which is constructed from a corrected low-fidelity model. The success...
-
FURTHER REMARKS ON THE NEO-CLASSICAL NAVIER-STOKES EQUATIONS
PublicationThe seminal Navier-Stokes equations have been stated yet before creation of principles of thermodynamics and the first and second laws. In the literature there is the common opinion that the Navier-Stokes equations cannot be taken as a thermodynamically correct model of “working fluid” which is able to describe transformation of “ heat” into “work” and vice versa. Therefore, in the paper, a new exposition of thermodynamically...
-
Analiza egzergetyczna bloku gazowo parowego współpracującego z obiegiem ORC
PublicationW pracy przedstawiono sposób przeprowadzania bilansu egzergetycznego dla obiegu Clausiusa – Rankina. Następnie przy pomocy programu EES współpracującego z bazą REFPROP 9.0 (Reference Fluid Thermodynamic and Transport Properties Database) [6] wykonany został bilans egzergetyczny dla układu kaskadowego siłowni CCGT – ORC, w którym blok gazowo – parowy współpracuje z obiegiem ORC. Obliczenia wykonano w oparciu o rzeczywiste parametry...