displaying 1000 best results Help
Search results for: SCRAP TYRES
-
RESEARCH ON HYDRODYNAMIC PEEK JOURNAL BEARINGS LUBRICATED WITH WATER AND OIL
PublicationThe main purpose of the research was to determine the possibilities and experimentally test the benefits of replacing conventional oil lubrication with ecological water lubrication. Tests were carried out on a test rig for hydrodynamic radial bearings under conditions representative of the expected applications for the bearing in water turbines. Bearings made from the polymer material PEEK (polyether ether ketone) were tested under static...
-
Investigation of the Effect of The Temperature and Magnetization Pattern on Flux Density, Instantaneous Torque, Unbalanced Magnetic Forces of a Surface Inset PMM
PublicationElectrical machines utilized in domestic applications such as ceiling fans should have low losses and cost. Permanent magnets are used instead of rotor excitation to reduce losses. Therefore, not only the losses of the rotor winding are eliminated, but also the efficiency of the machine is increased. A surface inset consequent pole (SICP) machine has also been used to reduce costs. Because less magnets are utilized in this structure....
-
Greening procedures and analytical parameters. The polychlorinated naphthalenes analysis in complex matrices as proof of concept
PublicationDue to the complexity of analytical procedures employed for the determination of wide spectrum of persistent organic pollutants (POPs), it is important to consider the green character of the applied protocols and propose the greenest solutions. In this review, the green aspects of several analytical procedures used for the determination of polychlorinated naphthalenes (PCNs) (as a representatives of POPs) in different types of...
-
Miniaturized Dual-Band SIW-Based Bandpass Filters Using Open-Loop Ring Resonators
PublicationThis article presents two novel architectures of dual-band substrate integrated waveguide (SIW) bandpass filters (BPFs). Initially, two identical open-loop ring resonators (OLRRs) are coupled face-to-face on the top of the SIW cavity to realize a dual-band single-pole BPF. To obtain two-pole dual-band characteristics, two OLRRs resonant units are assembled horizontally within the top metal layer of the SIW, which is a technique...
-
Digital microcontroller for sonar waveform generator
PublicationGenerating sounding signals is essential for the operation of active sonar. The system should be highly reliable. This can be achieved through architecture, communication between the devices, and a well-designed and self–testing software. The system presented in the article is responsible for the generation of hydroacoustic sounding signals, and ensures proper interaction between power amplifiers and power supplies. Thanks to its...
-
Nonlinear Viscoelastic Properties of Polyurethane Nanocomposites
PublicationIn recent years, the nonlinear viscoelastic behaviors of elastomeric nanocomposites have been examined, especially for a wide range of rubbery composite (including natural rubber) materials. This chapter describes the influence of fillers and nanofillers on the nonlinear viscoelastic properties of elastomeric polyurethane systems. These filled elastomers (similar to the classic natural rubber reinforced elastomers), also exhibit...
-
Wpływ smarowności na działania układu tribologicznego (impact of lubricity on the tribological system action)
Publicationthe paper presents analysis and evaluation, based on tests results, of the impact of lubricity of the used lubricating oils (shell argina t 40) on the action of boundary layer of sulzer 6zl40/48 engines aboard the ''włocławek'' sea-going ship. for comparison purposes, the same oils were tested with the ceramizer four-stroke engine (all types of the vidar four-stroke engines) regeneration agent added. so understood boundary layer...
-
Student model representation for pedagogical virtual mentors
PublicationThe paper concerns technological aspects of virtual mentors construction, especially concentrating on the student model representation. The article distinguishes several types of information that is gathered by the pedagogical agents and other educational platforms, including student knowledge model, student progress tracking, interaction process patterns and learner preferences. A set of technologies used for the student model...
-
Audio-visual surveillance system for application in bank operating room
PublicationAn audio-visual surveillance system able to detect, classify and to localize acoustic events in a bank operating room is presented. Algorithms for detection and classification of abnormal acoustic events, such as screams or gunshots are introduced. Two types of detectors are employed to detect impulsive sounds and vocal activity. A Support Vector Machine (SVM) classifier is used to discern between the different classes of acoustic...
-
STRUCTURE AND ALGORITHMS OF A DIAGNOSTIC DEVICE IN A WHEELED TRACTOR
PublicationDiagnostic device monitors the tractor’s technical condition and identifies the location of damaged components during operation. The diagnostic device detects and identifies the following types of defects: functional defects (uf) which affect performance, exhaust defects (ue) which increase toxic emissions and fuel consumption, defects that jeopardize driving safety (us), defects that affect engine performance (ud). The key component...
-
Analogue GPS repeater
PublicationThis article concerns the problem of difficulty in correct indoor Global Positioning System (GPS) signals reception due to attenuation. Radio signal repeaters are proposed as means to solve this problem. Firstly, the GPS signal characteristics are described, emphasizing their low power in the point of reception. In the second part, various applications of GPS signal repeater, where indoor GPS signals reception is required, are...
-
Roofing Materials as Pollution Emiters - Concentration Changes During Runoff
PublicationThe influence of roofing material on concentration of pollutants in roof runoff waters and changes of pollution concentration in time were investigated. In field studies four roofing material types were taken into consideration - ceramic tile, bituminous membrane, asbestos tile and zinc sheeting. Samples were collected since November 2007 to March 2008, anions, cations, metals, PAHs, pesticides and PCB were determined. The existence...
-
COMPARISON OF TWO MODELS OF CONDENSATION
PublicationIn the low-pressure part of steam turbine, the state path usually crosses the saturation line in penultimate stages. At least last two stages of this part of turbines operate in two –phase region. The liquid phase in this region in mainly created in the process of homogeneous and heterogeneous condensation. Several observations confirm however, that condensation often occurs earlier than it is predicted by theory i.e. before the...
-
Processing of acoustical data in a multimodal bank operating room surveillance system
PublicationAn automatic surveillance system capable of detecting, classifying and localizing acoustic events in a bank operating room is presented. Algorithms for detection and classification of abnormal acoustic events, such as screams or gunshots are introduced. Two types of detectors are employed to detect impulsive sounds and vocal activity. A Support Vector Machine (SVM) classifier is used to discern between the different classes of...
-
Fast simulation-driven design optimization of UWB band-notch antennas
PublicationIn this letter, a simple yet reliable and automated methodology for rapid design optimization of ultra-wideband (UWB) band-notch antennas is presented. Our approach is a two-stage procedure with the first stage focused on the design of the antenna itself, and the secondstage aiming at identification of the appropriate dimensions of the resonator with the purpose of allocating the band-notch in the desired frequency range. For the...
-
The structure of novel polyurethanes containing synthetic poly[(R,S)-3-hydroxybutyrate]
PublicationThe aim of this study was to estimate the structure of new polyurethanes with the potential to be used in medicine. Atactic poly[(R,S)-3-hydroxybutyrate], obtained via a ring-opening polymerization, and polycaprolactonediol or polyoxytetramethylenediol were used to built the soft segments. 4,4'-methylene dicyclohexyl diisocyanate and 1,4-butanediol were the components to form hard segments. Polyurethanes with low-molecular weight...
-
The use of weight in motion data to heavy vehicles - pavement interaction analysis
PublicationWeight in motion (WIM) is the element of modern intelligent transport systems created to control commercial vehicles and to detect overloaded items. Because all of the vehicles crossing the WIM station are weighed and recognized, given data can be used to vehicle-pavement interaction analysis. The paper presents the results of analysis based on data from seven WIM stations localized in Motorway and National Roads in Poland. The...
-
Mobile navigation system for visually impaired users in the urban environment
PublicationThis paper describes the prototype version of a mobile application supporting independent movement of theblind. Its objective is to improve the quality of life of visually impaired people, providing them with navigationalassistance in urban areas. The authors present the most important modules of the application. The module forprecise positioning using DGPS data from the ASG-EUPOS network as well as enhancements of positioning...
-
Influence of Self-Similar Traffic Type on Performance of QoS Routing Algorithms
PublicationProviding a Quality of Services (QoS) into current telecommunication networks based on packet technology is a big challenge nowadays. Network operators have to support a number of new services like voice or video which generate new type of traffic. This traffic serviced with QoS in consequence requires access to appropriate network resources. Additionally, new traffic type is mixed with older one, like best-effort. Analysis of...
-
Lightweight glass and metal roof structures in the 19th century. Architecture and construction.
PublicationThe 19th century brought new construction possibilities. The usage of metal elements in mesh structures, filled in with glass, resulted in creating entirely new types of objects. They have distinguished themselves in architecture and technical solutions. The envelope structures giving spatial interiors were arising very quickly. They have been enabling large light penetration, triggering them extremely bright. Thus these building...
-
Preparation and characterization of rigid polyurethane-polyglycerolnanocomposite foams
PublicationThis work reports on the preparation of polyurethane-polyisocyanurate (PUR-PIR) foams containing different polyglycerols and layered silicate nanoclays. The rigid polyurethane foams were obtained in a laboratory scale, in a single step method, from a two-component system with a NCO to OH groups ratio equal to two. The reaction mixture consisted of the proper amounts of a commercial oligoetherpolyol, polyglycerol, catalysts, water,...
-
Application of microturbines in CHP systems with reciprocating engines
PublicationThe analysis was carried out for Combined Heat and Power generation systems with micro-turbines power plants working on heat rejected from the reciprocating engine. The calculations were performed for GE Jerbacher engines of J320 GS- C05, J320 GS- C25 and J416 GS- B05 types. We considered different working media (both wet and dry fluids): water, ammonia, ethanol, methanol, methylacetylene (propyne), dimethyloether, sulphur dioxide,...
-
A Web-GIS tool for diagnosing spatial orientation of young adults: design and evaluation of Geo-Survey
PublicationSpatial orientation is the effectiveness with which one is able to assess the mutual location of objects relative to a point of reference or a system of coordinates. Traditionally, this ability has been evaluated through field navigation tests, which do not take into account the prevailing influence of free online maps and virtual walks on a person’s interpretation of space. In this context, this study presents a Web-GIS tool designed...
-
A Comprehensive Review of Reactive Flame Retardants for Polyurethane Materials: Current Development and Future Opportunities in an Environmentally Friendly Direction
PublicationPolyurethanes are among the most significant types of polymers in development; thesematerials are used to produce construction products intended for work in various conditions. Nowa-days, it is important to develop methods for fire load reduction by using new kinds of additivesor monomers containing elements responsible for materials’ fire resistance. Currently, additiveantipyrines or reactive flame retardants can be used during...
-
Corrigendum to “Fatigue life improvement using low transformation temperature weld material with measurement of residual stress” [Int. J. Fatigue 164 (2022) 107137]
PublicationWelding processes often produce high levels of tensile residual stress. Low transformation temperature (LTT) welding wires utilise phase transformation strains to overcome the thermal contraction of a cooling weld. In this paper, the residual stress within each weld was quantified using the milling/strain gauge method, being the strain change measured as the weldment was milled away. The fatigue tests were conducted under uniaxial...
-
Implementation of DIFAR Processing in ASW Dipping Sonar
PublicationThis paper presents the implementation of the signal processing algorithm used by buoy DIFAR (Directional Frequency Analysis and Recording), that is fully operational on Polish Navy anti-submarine warfare (ASW) helicopters and ships, applied to dipping sonars for detection and tracking of submarines. The development of the DSP algorithms was a part of the modernization of sonars conducted at the Gdansk University of Technology....
-
Low-frequency tripping characteristics of residual current devices
PublicationFast development of various types of converters makes their utilization in industry and in domestic installations very common. Due to converters, an earth fault current waveform in modern circuits can be distorted or its frequency can be different than 50/60 Hz. Frequency of earth fault (residual) current influences tripping of residual current devices which are widely used in low voltage systems. This paper presents the behaviour...
-
The Relational Benefits and the Quality of Services in Tourism
PublicationIn a very competitive environment, it is highly important to identify the indicators that exert a major influence on customer satisfaction and loyalty. Based on the current relationship marketing concept of relational benefits (Gwinner, Gremler, Bitner, 1998; Hennig-Thurau, Gwinner, Gremler, 2002) and destination quality (Blazquez-Resino, Molina, Esteban-Talaya, 2015), a conceptual model was built. The present paper aims to analyse...
-
Fatigue life improvement using low transformation temperature weld material with measurement of residual stress
PublicationWelding processes often produce high levels of tensile residual stress. Low transformation temperature (LTT) welding wires utilise phase transformation strains to overcome the thermal contraction of a cooling weld. In this paper, the residual stress within each weld was quantified using the milling/strain gauge method, being the strain change measured as the weldment was milled away. The fatigue tests were conducted under uniaxial...
-
Hydrological Dry Periods versus Atmospheric Circulations in the Lower Vistula Basin (Poland) in 1954–2018
PublicationThe paper discusses the impact of atmospheric circulation on the occurrence of droughts. The research in-cludes mean monthly discharges for 7 rivers in 1954-2018. Dry periods were determined with Standardised Streamflow Indices (SSI-12). Additionally, the circulation type calendar for Central Poland was used to determine the atmospheric circulation indices: western zonal (W), southern meridional (S) and cyclonicity (C). The analyses...
-
Bayesian Optimization for solving high-frequency passive component design problems
PublicationIn this paper, the performance of the Bayesian Optimization (BO) technique applied to various problems of microwave engineering is studied. Bayesian optimization is a novel, non-deterministic, global optimization scheme that uses machine learning to solve complex optimization problems. However, each new optimization scheme needs to be evaluated to find its best application niche, as there is no universal technique that suits all...
-
Application of deep eutectic solvents in bioanalysis
PublicationThe application of deep eutectic solvents (DESs) is sharply surging as a green alternative to conventional solvents due to their unique properties in terms of simplicity of preparation, designability and low cost. A great deal of attention has been paid to the application of these green solvents in analytical chemistry in recent years, and a lot of interesting work has been reported. This review summarizes the most relevant applications...
-
Stability investigation of the PCM nanocomposites
PublicationIn present study was showed the results of research the stability of nanoPCMs in terms of types and concentrations of surfactant used. For stearic acid has been added PVP or oleic acid in concentrations of 0%, 5% and 10%. Nanoparticles TiO2 and Al-2O3 in concentration of 1% were chosen to be researched in this test. The mixing of nanocomposites has been done in an ultrasonic scrubber in which the samples were placed for 45 mins....
-
The methodology of design of satellite working mechanism of positive displacement machine
PublicationIn this paper is described a methodology of design of satellite mechanism consisting of two noncircular gears (externally toothed rotor and internally toothed curvature) and circular gears (satellites). In the presented methodology is assumed that the rotor pitch line is known, and the curvature pitch line is necessary to designate. The presented methodology applies to mechanisms for which the number of the curvature humps is at...
-
Investigation of Liquid–Gas Flow in a Horizontal Pipeline Using Gamma-Ray Technique and Modified Cross-Correlation
PublicationThis article presents the application of the radioisotope absorption method in the study of two-phase water–air flow in a horizontal pipe. The measurement principle and the test stand are briefly described. The main part of the article presents the signal analysis methods applied to data obtained from scintillation detectors. Because these signals are mostly stochastic waveforms, they were analyzed statistically using the cross-correlation...
-
HEALTH SAFETY OF BREAD IN SMALL BAKERIES
PublicationThe aim of the article is to present the safety and health risks in the production process of bread, supported by research in small bakeries located in the Pomeranian Voivodeship. Health safety of bread is one of the features that decide its quality. This article additionally presents other determinants influencing the quality of bread. It also demonstrates opinions showing food safety as a separate attribute of quality. The paper...
-
Wideband Channel Measurements for Polarised Indoor Off-Body Communications
PublicationThis paper presents the initial results of wideband channel measurements for polarised off-body communication at 5.8 GHz, in an indoor environment. Channel Impulse Response measurements were performed simultaneously for two orthogonal polarisations of the wearable antenna, and repeated for vertical and horizontal orientations of the off-body one. Four types of measurement scenarios were considered in order to investigate the influence...
-
Design of control algorithms for mobile robots in an environment with static and dynamic obstacles
PublicationThis article proposes the construction of autonomous mobile robots and designing of obstacle avoidance algorithms for them. Nowadays, mobile robots are gaining more and more popularity on the customer as well as industrial market, for example as automatic vacuum cleaners or lawnmowers. Obstacle avoidance algorithms play an important role in performance of this types of robots. The proposed algorithms were designed for builds with...
-
Regional quality contests based on business excellence models – Pomeranian case study
PublicationCompetitions based on models of organizational excellence have significant potential. Organizations participating in these initiatives have the chance not only to get marketing benefits, but also gain comprehensive knowledge about their management systems. Moreover, thanks to the structure of models of excellence an organization can plan in detail the improvement activities in its main processes. The aim of the authors is to analyze...
-
Implementation of high-precision computation capabilities into the open-source dynamic simulation framework YADE
PublicationThis paper deals with the implementation of arbitrary precision calculations into the open-source discrete element framework YADE published under the GPL-2+ free software license. This new capability paves the way for the simulation framework to be used in many new fields such as quantum mechanics. The implementation details and associated gains in the accuracy of the results are discussed. Besides the "standard" double (64 bits)...
-
Digitalization of High Speed Craft Design and Operation Challenges and Opportunities
PublicationIn recent years, global demands for safe and sustainable ships led to dramatic changes in the maritime industry. Digitalization is expected to play an important part in the future. This is supported by analysis of the autonomous ships market which shows that digitalization of large ship types such as tankers and container ships is well on track. Although to date designs of autonomous High-Speed Craft (HSC) have been developed,...
-
Eksperymentalne i numeryczne badania parametrów dynamicznych trybuny stalowej
PublicationTrybuny stalowe to konstrukcje, które odnajdują swoje zastosowanie głównie podczas wydarzeń sportowych, koncertów muzycznych oraz innych wydarzeń, którym towarzyszą rytmiczne aktywności widzów i głośna muzyka. Ze względu na smukłość oraz lekkość elementów z jakich wykonana jest konstrukcja trybuny jest ona bardzo łatwo wzbudzana przez ludzi do drgań. Z przeprowadzonej w pracy [4] analizy modalnej wynika, że masa ludzi prowadzi...
-
The importance of the bottom layer in double-layer porous asphalt for noise reduction
PublicationDouble-layer porous asphalt concrete (DPAC) surfaces are generally considered to be the acoustically most effective low noise road surfaces ready for implementation. While DPAC used on highways in warm climates may have an average life of around 8 years, in Scandinavia with severe winter climate DPAC usually survive only about 3 years; partly due to wear of studded tyres. An ongoing project in Sweden, applying DPAC and single-layer...
-
Number of registered BEV and PHEV vehicles in 2011-2016 (in thousands)
Open Research DataThere are three main types of vehicles that are generally regarded as an electric car. These include:
-
Thermal properties of strontium–borate glasses and glass-ceramics containing bismuth and vanadium oxides measured with DSC method
Open Research DataThermal properties of strontium–borate glasses and glass-ceramics containing bismuth and vanadium oxides was measured by DSC.
-
Measurements of ultrasonic bulk and guided wave propagation in additively manufactured cubes and plates obtained by ultrasonic pulse velocity analyzer and scanning laser vibrometry
Open Research DataThe DataSet contains the results of measurements of ultrasonic wave propagation in additively manufactured samples made of polylactic acid (PLA). Three types of raster angles in two consecutive layers were assumed: 0°/90° (#1), 45°/-45° (#2) and 90°/90° (#3) with respect to the x-axis. For each printing variants a cubic sample (#C1-3) with dimensions...
-
PERSUADE PoroElastic Road SUrface: an innovation to Avoid Damages to the Environment
ProjectsProject realized in Faculty of Mechanical Engineering according to 226313 agreement from 2009-08-17
-
UUV and AUV Vehicles as the autonomous systems for naval applications
PublicationThere is a growing pressure to investigate how to design and build the unmanned underwater vehicles of different types which are devoted towards performing many tasks under the water surface according to the data missions. During the recent years the Department of Ship Design and Subsea Robotics, Faculty of Ocean Engineering and Ship Technology, Gdansk University of Technology designed and built a few types of unmanned underwater...
-
Knowledge risks in organizations – Insights from companies
PublicationPurpose: Knowledge risks are increasingly becoming a great challenge to a variety of organizations. At the same time, academic research on such types of risks, their consequences, and potential ways of overcoming them is still scarce and fragmented. To fill this gap, the paper aims to find out do companies manage their knowledge risks, what are the possible knowledge risks they face and have they observed an increase of knowledge...
-
Residual Current Devices: Selection, Operation, and Testing
PublicationIn this book, the idea for residual current protection has been presented. The evolution in construction types of residual current devices, which has taken place over decades, is discussed. Types and functional properties of the contemporary residual current devices are described. The main parameters of these devices, from the point of view of their selection and application, are indicated. Special constructions of the protective...