displaying 1000 best results Help
Search results for: NOISE DOSIMETRY
-
Development of low noise CCD readout front-end
Publication -
Investigation of Noise Threats and Their Impact on Hearing in Selected Schools
PublicationNoise measurements conducted in selected schools in Gdansk area are presented in this paper. The main aim of this research was to determine noise threats at schools. Some objective measurements of the acoustic climate were performed employing a noise monitoring station engineered at the Multimedia System Department, Gdansk University of Technology. Simultaneously, subjective noise annoyance examinations were carried out among pupils...
-
On electrochemical noise analysis for monitoring of uniform corrosion rate
PublicationSzybkość korozji jest określona przez rezystancję polaryzacyjną warstwy metal-elektrolit. Jej wartość może być wyznaczona za pomocą pomiarów szumów elektrochemicznych. Przedstawiono szczegółowo algorytm wyznaczania wartości rezystancji polaryzacyjnej na podstawie rejestrowanych sygnałów losowych dla przykładowych wyników badań eksperymentalnych. Oszacowano dokładność wyznaczanej wartości.
-
Application of non-stationary techniques in the analysis of electrochemical noise.
PublicationKlasyczne podejście do analizy szumu elektrochemicznego oparte jest na wstępnym założeniu jego stacjonarności. Pomimo użyteczności, tego typu analiza często prowadzi do mylących wniosków, wynikających z niestacjonarności rejestrów szumowych. W pracy przedstawione zostały możliwości krótkoczasowej transformacji Fouriera, umożliwiającej uzyskanie zależnych od czasu widm mocy sygnału. Osiągane jest to dzięki wykorzystywaniu ruchomego,...
-
Substrate noise-aware floorplanning for mixed-signal SOCs.
PublicationOpisano nową metodę projektowania systemów na chipie z uwzglednieniem minimalizacji szumu podłożowego. Optymalizacje rozmieszczenia bloków układowych na chipie uzyskuje się dzieki wykorzystaniu algorytmu ewolucyjnego minimalizującego funkcję celu uwzględniającą poziom szumu podłożowego.
-
Noise performance of continuous-time active-RC filters.
PublicationW pracy przedstawiono metodę analizy właściwości szumowych filtrów aktywnych RC czasu ciągłego. Prezentowana procedura wykorzystuje model integratorowy, z odpowiednim dla tej klasy filtrów opisem macierzowym. Dokładność osiągniętych wyników teoretycznych dla przykładowego filtru potwierdzono rezultatami otrzymanymi przy pomocy symulatora SPICE.
-
Noise and Electro-Ultrasonic Spectroscopy of Conducting PolymerThick Films
PublicationThick conducting films based on conducting polymer are characterized by DC conductivity and noise in temperature range 10 to 300 K. Conducting polymers could be used e.g. for the top electrode (cathode) in the solid tantalum or niobium capacitors. On the conducting polymer layer the top layer of carbon/graphite and/or silver polymer based pastes is applied in the capacitor technology. Our samples structure consists of conducting...
-
Multichannel self-optimizing active noise control scheme
PublicationThe problem of cancellation of a nonstationary sinusoidal interference, acting at the output of an unknown multivariable linear stable plant, is considered. The proposed cancellation scheme is a nontrivial extension of the SONIC (self-optimizing narrowband interference canceller) algorithm, developed earlier for single-input, single-output plants. In the important benchmark case - for disturbances with randomwalk-type amplitude...
-
Design of low noise preamplifers for characterization of LSCO bolometers
PublicationW artykule przedstawiono wymagania stawiane układom do pomiaru szumów bolometrów. Ze względu na niski poziom mierzonych szumów układy te wymagają zastosowania niskoszumnych przedwzmacniaczy i układów ustalających punkt pracy badanych detektorów. Omówiono konstrukcje dwóch przedwzmacniaczy z zintegrowanymi układami polaryzacji. Przedstawiono wyniki pomiarów szumów w zakresie częstotliwości 10-90Hz. Przedstawiono możliwości ulepszenia...
-
Modeling of substrate noise block properties for early rediction.
PublicationZaproponowano nowe podejscie do modelowania zakłóceń podłozowych we wczesnym etapie projektowania systemów na wspólnym podłożu krzemowym. Modelowanie zakłóceń oparto na założeniu, że głównym źródłem zakłóceń podłożowych jest sieć zasilająca. W oparciu o przeprowadzone symulacjie wykazano słusznosć takiej metody.
-
Substrate noise modeling in early floorplanning of MS-SOCs.
PublicationW pracy zaproponowano model częstotliwościowy bloków analogowych wrażliwych na zakłócenia oraz bloków cyfrowych generujących zakłócenia w systemach mieszanych realizowanych na wspólnym podłożu krzemowym. Zaproponowane modele zostały wykorzystane w oprogramowaniu optymalizującym rozmieszczenie bloków funkcjonalnych na struktórze krzemowej. Dzieki użyciu procedur optymalizacyjnych uzyskano znaczącą redukcje poziomu zakłóceń przy...
-
Methods of electrochemical noise analysis for investigation of corrosion processes
PublicationKorozja elektrochemiczna może być oceniana za pomocą przpływu ładunków między korodującym metalem a elektrolitem. Zwykle, przpływ ładunku obserwuje się w układzie trzech elektrod jako fluktuacje prądu i napięcia (szumy elektrochemiczne). Na podstawie analizy szumów elektrochemicznych można wykrywać różne rodzaje korozji. Korozja jednorodna jest oceniana za pomocą wartości rezystancji polaryzacyjnej występującej między metalem a...
-
Biological hazards in low noise, poroelastic road surfaces
PublicationDrainage pavements as well as poroelastic pavements ("PERS") are a very efficient way to decrease traffic noise by reducing tire/road noise at the source as well as noise propagation over the road surface. Many noise generating mechanisms at the tire/road interface are very much reduced by road porosity (pipe resonance, "air pumping", Helmholtz resonance and the horn effect). A well-designed porous or poroelastic road surface may...
-
UNDERWATER NOISE GENERATED BY A SMALL SHIP IN THE SHALLOW SEA
PublicationStudy of the sea noise has been a subject of interest for years. The first work of this scope were published at the turn of the twentieth century by Knudsen (KNUDSEN et al., 1948) and G. Wenz (WENZ, 1962). Disturbances called "shipping noise" are one of the important components of the sea noise. In this work the results of an experimental research of underwater noise produced by a small ship of a classic propulsion are...
-
Robustness of quantum-randomness expansion protocols in the presence of noise
PublicationIn this paper we investigate properties of several randomness generation protocols in the device independent framework. Using Bell-type inequalities it is possible to certify that the numbers generated by an untrusted device are indeed random. We present a selection of certificates which guarantee two bits of randomness for each run of the experiment in the noiseless case and require the parties to share a maximally entangled state....
-
Effects of mechanical stress on electrical arameters and noise of supercapacitors
PublicationResults of noise and electrical parameters measurements of prototype electrochemical double layer capacitors (EDLC) are reported at the presence of selected mechanical stress. This issue is of great importance due to future applications in wearable technology. The measurement results are compared, and we may conclude than flicker noise is more sensitive to any stress than other considered electrical parameters.
-
Temperature influence on tyre/road noise of selected tyres
PublicationAir and road temperatures substantially affect road vehicle noise emission. The temperature influence on tyre/road noise depends mainly on tyre-road combination. It is different for dense and porous pavements, for bituminous and cement ones. It differs also depending on tyres. The correction procedures for temperature effect are still under consideration and preparation. Tyre/road noise measurements using CPX method were performed...
-
Comparison of road and laboratory measurements of tyre/road noise
PublicationTyre/road noise is one of the major environmental problems related to road traffic. There are several measuring methods of tyre/road noise that may be carried out on the road (for example Coast-down and Close Proximity Method) or in the laboratory (Drum Method). Road measurements are preferred for evaluations of pavement properties while laboratory methods are mostly used to evaluate tyres. One of the biggest problems associated...
-
Tyre/road noise reduction by a poroelastic road surface
PublicationLow noise road surfaces of existing types may in favourable cases and in new conditions provide up to 7 dB of noise reduction. For higher noise reductions, innovative solutions must be sought. Poroelastic road surfaces (PERS) may be such a solution, which currently is studied in the EU project PERSUADE. This paper presents results of trials with a PERS version prefabricated by one of the project partners. Tests were made in a laboratory...
-
Waveform design for fast clutter cancellation in noise radars
PublicationCanceling clutter is an important, but computation-ally intensive part of signal processing in noise radars. It is shown that considerable improvements can be made to a simple least squares canceler if minor constraints are imposed onto noise waveform. The proposed scheme is potentially capable of canceling clutter in real-time, even for high sampling rates.
-
Assessment of Supercapacitor’s Quality by Means of Low Frequency Noise
PublicationLow frequency noise is a well-known tool for quality and reliability assessment of electronic devices. This phenomenon is observed in different electrochemical devices as well (e.g., smart windows, electrochemical corrosion processes). Thus, we can assume that the same tool can be used to asses quality of supercapacitors. Their quality is usually determined only by capacitance and/or equivalent series resistance (ESR), or impedance....
-
IMPULSE NOISE ASSOCIATED WITH FIRING HANDHELD MILITARY WEAPONS
PublicationSports, hunting and military shooting grounds are well known sources of noise that can be disruptive both for people present at those facilities, as well as for people and animals that live nearby. What is more, shooters are also subjected to very painful and dangerous impulse noise. The paper discusses the issues related to the noise immission during firing of small firearms of military type that are typical for Poland. The experiments...
-
Speed dependency of temperature effects on road traffic noise
PublicationRecently, a new literature review on the influence of temperature on tire/road noise became available, based on a compilation of large amounts of data from empirical research. This review showed that the effect of temperature is roughly double of that previously assumed and taken account of in international standards. This makes temperature one of the main sources of error in measurement results. Furthermore, it suggested that...
-
Tire camber angle influence on tire-pavement noise
PublicationTaking into account tire-pavement noise and tires classification with respect to noise emission special measurement methods are usually used. When two of them are applied (the Laboratory Drum Method (DR) and the Close-Proximity Method (CPX)) the investigator has to be sure that the position of the tire is correct. The authors of this paper thought about tire position as tire (wheel) alignment in particular tire camber angle. They...
-
Separability Assessment of Selected Types of Vehicle-Associated Noise
PublicationMusic Information Retrieval (MIR) area as well as development of speech and environmental information recognition techniques brought various tools in-tended for recognizing low-level features of acoustic signals based on a set of calculated parameters. In this study, the MIRtoolbox MATLAB tool, designed for music parameter extraction, is used to obtain a vector of parameters to check whether they are suitable for separation of...
-
Temperature influence on tyre/road noise frequency spectra
PublicationThe correction for temperature effect on measured tyre/road noise is very important as it may be one of the main sources of errors in measurement results due to substantial influence of this parameter on obtained values. The latest version of the Technical Specification ISO/CD TS 13471-1 about Temperature Corrections contains a proposal of correction procedure for normalizing measured noise levels to a reference air temperature...
-
Methods of trend removal in electrochemical noise data – overview
PublicationIn this paper we shall review popular methods of trend removal from electrochemical noise time records. The basic principles of operation of the six most popular methods are explained. The proposed methods are: high - pass filtering, Moving Average Removal, polynomial detrending, wavelet detrending, Empirical Mode Decomposition and Variational Mode Decomposition. Estimation of trend removal quality...
-
Sound quality metrics applied to road noise evaluation
PublicationRoad noise monitoring systems typically measure sound levels in specific time periods. The more insightful approach suggests to measure also the nature of noise. Sound quality of sounds such as car noise can be objectively evaluated by several parameters. One of them is psychoacoustic annoyance, described by loudness, tone color, and the temporal structure of sound. In this paper the assessment of several sound quality parameters, such...
-
Semi-adaptive feedback active control of MRI noise
PublicationA feedback controller is proposed for cancellation of magnetic resonance imaging (MRI) noise. The design of the controller takes into account specific features of the MRI noise signal. Simulation results show that a considerable rejection rate of the MRI noise can be obtained.
-
Noise effect on parameters of quiet sonar with code modulation
PublicationEarlier publications of the paper authors have shown that the use of code keying mixed with the CW FM sound signal allows the significant reduction in the distance measurement error, compared to classic silent CW FM sonar. In addition to the code modulation parameters, the magnitude of this error is influenced by the received input acoustic noise. The article shows the dependence of the input signal-to-noise ratio and the sound...
-
Electrochemical noise analysis methods for the investigation of corrpsion processes
PublicationProcesy korozji mogą być badane przez obserwacje przepływu ładunków między elektrolitem a korodującą elektrodą metalową. Przepływy te są obserwowane jako fluktuacje prądu i napięcia nazywane szumem elektrochemicznym. Różne rodzaje procesów korozji mogą być identyfikowane za pomocą szumów elektrochemicznych. Szybkość korozji jednorodnej jest określana przez estymację rezystancji polaryzacji występującej między elektrolitem a metalem....
-
On accurracy of polarization resistance estimation by electrochemical noise measurements
PublicationPrzedstawiono sposób estymacji rezystancji polaryzacji, wykorzystywanej do oceny szybkości procesów korozji. Zaproponowano formułę określającą błąd losowy estymacji rezystancji polaryzacji. Przytoczono i przedyskutowano eksperymentalne wyniki estymacji rezystancji polaryzacji na podstawie pomiarów szumów elektrochemicznych w układzie trzech elektrod pomiarowych.
-
Projects of noise level on railway lines
Open Research DataProjects of acoustic signals from railway lines for further analysis in the BK Connect program.
-
projects of noise level on railway lines
Open Research DataProjects of acoustic signals from railway lines for further analysis in the BK Connect software.
-
On sequences of the white noises
PublicationPodano dowód mocnego prawa wielkich liczb dla funkcjonałów gaussowskich.
-
Sensitivity calibration procedures in optical‐CT scanning of BANG®3 polymer gel dosimeters
Publication -
Identification of inherent noise components of semiconductor devices on an example of optocouplers
PublicationIn the paper, a method of estimation of parameters of Gaussian and non-Gaussian components in the noise signal of semiconductor devices in a frequency domain is proposed. The method is based on composing estimators of two spectra, corresponding to noise (Gaussian component) and two-level RTS noise (non-Gaussian component). The proposed method can be applied for precise evaluation of the corner RTS frequency fRTS in the noise...
-
Directivity of tire/road noise emission for selected tires and pavements
PublicationPraca pośwoęcona jest kierunkowości emisji hałasu opon i nawierzchni drogowych. Opony są dominującym źródłem haasu w pojaździe poruszającym się w typowych warunkach ruchu drogowego. Hałas ten nie jest bezkierunkowy jak to przyjmuje się w modelach obliczeniowych hałasu. Takie założenia wynikają z ograniczonej dostępności danych dotyczących kierunkowości i mogą prowadzić do niedokładności przy prognozowaniu hałasu drogowego. Praca...
-
Pitting corrosion characterization by electrochemical noise measurements on asymmetric electrodes
PublicationKorozja wżerowa stali nierdzewnych może być wykryta za pomocą obserwacji charakterystycznych sygnałów prądowych, jakie płyną między dwiema elektrodami metalowymi. W artykule proponuje się wyznaczanie funkcji bispektrum dla układu dwóch elektrod o istotnie różnej powierzchni narażonej na występowanie korozji. Proponowana metoda została zastosowana do analizy korozji wżerowej stali 0H18N9 powstającej pod wpływem 1M roztworu FeCl3...
-
Irregular variations in GPS time series by probability and noise analysis
Publication -
Impact of Spatial Noise Correlation on Bearing Accuracy in DIFAR Systems
PublicationDIFAR type underwater passive systems are one of the more commonly used tools for detecting submarines. At the design stage, which usually uses computer simulations, it is necessary to generate acoustic noise of the sea. It has been shown that correlating noise significantly reduces these errors compared to the assumption that noise is uncorrelated. In addition, bearing errors have been shown to be the same in systems with a commonly...
-
Evaluation of Lombard Speech Models in the Context of Speech in Noise Enhancement
PublicationThe Lombard effect is one of the most well-known effects of noise on speech production. Speech with the Lombard effect is more easily recognizable in noisy environments than normal natural speech. Our previous investigations showed that speech synthesis models might retain Lombard-effect characteristics. In this study, we investigate several speech models, such as harmonic, source-filter, and sinusoidal, applied to Lombard speech...
-
Selective monitoring of noise emitted by vehicles involved in road traffic
PublicationAn acoustic intensity probe was developed measures the sound intensity in three orthogonal directions, making possible to calculate the azimuth and elevation angles, describing the sound source position. The acoustic sensor is made in the form of a cube with a side of 10 mm, on the inner surfaces of which the digital MEMS microphones are mounted. The algorithm works in two stages. The first stage is based on the analysis of sound...
-
Noise profiling for speech enhancement employing machine learning models
PublicationThis paper aims to propose a noise profiling method that can be performed in near real-time based on machine learning (ML). To address challenges related to noise profiling effectively, we start with a critical review of the literature background. Then, we outline the experiment performed consisting of two parts. The first part concerns the noise recognition model built upon several baseline classifiers and noise signal features...
-
Generation-recombination and 1/f noise in carbon nanotube networks
PublicationThe low-frequency noise is of special interest for carbon nanotubes devices, which are building blocks for a variety of sensors, including radio frequency and terahertz detectors. We studied noise in as-fabricated and aged carbon nanotube networks (CNNs) field-effect transistors. Contrary to the majority of previous publications, as-fabricated devices demonstrated the superposition of generation-recombination (GR) and 1/f noise...
-
Two-stage method of impulsive noise detection for audio signals
PublicationPrzedstawiono nowa dwuetapową metodę detekcji zakłóceń impulsowych opartą na analizie funkcji gęstości rozkładu prawdopodobieństwa zakłóconego sygnału. Opisano algorytm określania poziomu wyzwalania detektora progowego.
-
Piece-wise constant approximation method of identification of RTS noise
PublicationPrzedstawiono nową metodę wydzielania szumów RTS z całkowitych szumów przyrządów półprzewodnikowych. Metoda ta oparta jest na aproksymacji liniowo odcinkowej przebiegu szumowego.Przedstawiono wyniki zastosowania tej metody do wydzielenia dwupoziomowego szumu RTS z szumu przyrządu półprzewodnikowego.
-
Fast clutter cancellation for noise radars via waveform design
PublicationCanceling clutter is an important, but very expensive part of signal processing in noise radars. It is shown that considerable improvements can be made to a simple least squares canceler if minor constraints are imposed onto noise waveform. Using a combination of FPGA and CPU, the proposed scheme is capable of canceling both stationary clutter and moving targets in real-time, even for high sampling rates.
-
Resistance Noise Higher-Order Spectrums in Nanoparticle Gas Sensors.
PublicationPrzedstawiono badania fluktuacji rezystancji sensora gazu wykonanego z nanocząstek WO3. Stwierdzono występowanie składowych o rozkładzie prawdopodobieństwa różnym od rozkładu Gaussa. W celu zwiększenia czułości i selektywności wykrywanych gazów zastosowan do analizy obserwowanych fluktuacji spektra wyższych rzędów.
-
Applications of electrochemical noise technique in stress corrosion cracking diagnosis
PublicationW pracy przedstawione zostały rezultaty analizy prądowego szumu elektrochemicznego, generowanego podczas korozji naprężeniowej próbek stali stopowej. W przeciwieństwie do tradycyjnych metod analizy nie zakładano stacjonarności analizowanych sygnałów. Zamiast tego analizie poddana została zmodyfikowana widmowa odpowiedź szumowa o charakterze zależnym od czasu. Rezultaty badań skonfrontowano z wynikami otrzymanymi za pomocą techniki...