Search
Institute of Energy
Publications
Filters
total: 1026
displaying 1000 best results Help
Catalog Publications
Year 2004
-
100 lat Laboratorium Maszynowego na Politechnice w Gdańsku.
PublicationWydanie albumowe poświęcone 100-letniej historii Laboratorium Maszynowego na Politechnice w Gdańsku. W opisie omówiono funkcje, jakie pełniło laboratorium w okresie istnienia. Początkowo był to zakład energetyczny zaopatrujący uczelnię w ciepło, energię elektryczną i wodę oraz laboratorium dydaktyczne dla studentów. W ostatnim okresie pełni ono głównie rolę laboratorium dydaktycznego oraz naukowo-badawczego. Część ilustracyjna...
-
100 lat Laboratorium Maszynowego na Politechnice w Gdańsku 1904-2004.
PublicationPrzedstawiono 100-letnią historię Laboratorium Maszynowego na Politechnice w Gdańsku. Omówiono funkcje, jakie pełniło laboratorium w okresie istnienia. Początkowo był to zakład energetyczny zaopatrujący uczelnię w ciepło, energię elektryczną i wodę oraz laboratorium dydaktyczne dla studentów. W ostatnim okresie pełni ono głównie rolę laboratorium dydaktycznego oraz naukowo-badawczego. Część ilustracyjna zawiera unikalne zdjęcia...
-
Aktualny stan prac nad napędem hybrydowym pojazdów na Politechnice Gdańskiej.
PublicationOpisano prace związane z modernizacją eksperymentalnego pojazdu hybrydowego PH-MAK oraz stanowiska badawczego, którego głównym elementem jest hamownia podwoziowa. Modernizacja pojazdu objęła, między innymi, wymianę gaźnikowego silnika spalinowego na zasilany wtryskowo silnik Lombardini LGW 523 MPI, zastosowanie akumulatorów żelowych nowej generacji i zakup sterownika baterii akumulatorów Badicheq, który umożliwia dokładny pomiar...
Year 2010
-
1D Model Callibration on the Basis on 3D calculations for Tesla Turbine
PublicationThe paper presents the system of equations for axisymmetriclaminar flow, after averaging, through the width of interdisk slit ofTesla turbine. Coefficients were introduced, as a result ofaveraging, that improve the efficiency of 1D model. The minimalnumber of such coefficients was determined. The 1D modelmakes it possible to attain analytical solutions to an accuracylimited by these coefficients. Calibration of 1D model depends...
-
A model of liquid film breakdown formed due to impingement of a two-phase jet on a horizontal surface
PublicationThe present work aims to provide an explanation to the phenomenon of breakdown of the thin liquid film created by impinging two-phase, liquid-gas jet. Existing in the literature models describe merely thebreakdown of single phase liquid films. The model presented here is based on examination of mass and energy equations under the applied criterion of the minimum of total energy. That allows to determinethe minimum thickness of...
-
A thermodynamic criterion for selection of working fluid for subcritical and supercritical domestic micro CHP
PublicationW pracy przedstawiono kryterium termodynamiczne doboru czynnika roboczego dla mikrosiłowni pracującej w warunkach podkrytycznych i nadkrytycznych. Przeanalizowano 20 płynów możliwych do wykorzystania w mikrosiłowni ORC. Z analizy wynika, że najlepszym płynem roboczym jest etanol, R123 oraz R141b.
Year 2003
-
3D calculations of aerodynamic forces causing self-excited vibrations of turbine rotor systems. Part I: Shroud seal flow inwestigations
PublicationOpisano numeryczną i doświadczalną metodę badania przepływu w uszczelnieniu nadbandażowym stopnia turbinowego. Badania numeryczne przeprowadzono programem Fluent, a badania doświadczalne wykonano na powietrznej turbinie modelowej. Uwzględniono niesymetryczny rozkład szczeliny nadbandażowej na skuteknie centrycznego położenia osi wirnika względem osi cylindra. Zamieszczono przykładowe wyniki.
-
3D calculations of aerodynamic forces causing self-excited vibrations of turbine rotor systems. Part II: Pressure forces
PublicationPrzedstawiono wyniki badań numerycznych sił generowanych w uszczelnieniu nadbandażowym stopnia turbinowego przeprowadzone metodą Fluent. Uwzględniono niecentryczne położenie osi wirnika względem osi korpusu. Rozpatrzono bandaże o różnej geometrii. Niektóre wyniki zweryfikowano doświadczalnie.
-
Aerodynamic excitations generated in turbine shroud clearance determined bymeans of neural networks
PublicationSiły aerodynamiczne generowane w uszczelnieniach turbinowych z reguły opisywane są modelem liniowym. Przy dużych drganiach wirnika sposób ten daje niezbyt dokładne wyniki. Zaproponowano wykorzystanie sieci neuronowych do określania sił ciśnieniowych powstających w uszczelnieniu. Wyniki porównano z badaniami eksperymentalnymi.
Year 2012
-
A closed loop thermosyphon with conventional or minichannel based condenser and evaporator
PublicationPrzedstawiono uogólniony model termosyfonu, który może być rozpatrywany dla szeregu wariantów.Model opiera się na jednowymiarowych równanich masy, pędu i energii. Rozpatrzono dwa przypadki termosyfonu, tj. grzanie strony pionowej i chłodzenie strony pionowej oraz drugi, gdzie termosyfon jest ogrzewany na stronie pionowej a chłodzony na poziomej.
-
A comparative study of different methods for heat transfer enhanced by the use of TVG
PublicationArtykuł dotyczy badań eksperymentalnych i numerycznych intensyfikacji wymiany ciepła w modelowym wymienniku ciepła z turbulizatorami przepływu dla różnej geometrii turbulizatorów. Do badań eksperymentalnych wykorzystano termografię ciekłokrystaliczną a modelowanie fizyczne wykonano za pomocą kodu komputerowego FLUENT.
Year 2015
-
A commercial gas boiler fitted with the ORC module as perspective solution for households
PublicationIn this paper the applicability of the commercial gas boiler (De Dietrich DTG X23N) coupled with the laboratory prototype micro ORC setup was experimentally studied. The main objective was to determine the working fluid capability to obtain required temperatures of vapour prior to the turbine, attainable heat rates and efficiencies of the whole system. The boiler thermal power was 25 kW. Tests were carried out with a single stage...
-
A Model of Thermal Energy Storage According to the Convention of Bond Graphs (BG) and State Equations (SE)
PublicationThe main advantage of the use of the Bond Graphs method and State Equations for modeling energy systems with a complex structure (marine power plants, hybrid vehicles, etc.) is the ability to model the system components of different physical nature using identical theoretical basis. The paper presents a method of modeling thermal energy storage, which is in line with basic BG theory. Critical comments have been put forward concerning...
-
Acoustic journal bearing - A search for adequate configuration
PublicationClassical non-contact bearings are already used in a number of specialist applications but there are somespecialist areas where they cannot be used for variety of reasons and acoustic sliding bearings could be an alternative. The paper presents the quest for a configuration of an acoustic journal bearing and shows that the overall shape of the bearing and its geometry are of a vital importance for the load capacity oft he bearing....
Year 2011
-
A common method for calculation of flow boiling and flow condensation heat transfer coefficients in minichannels with account of nonadiabatic effects
PublicationW pracy przedstawiono metodę ogólną wyznaczania współczynników przejmowania ciepła podczas wrzenia w przepływie i kondensacji w przepływie w minikanałach z uwzględnieniem efektu nieadiabatycznego. Uwzględnia ona wpływ modyfikacji naprężeń stycznych na granicy ciecz-para na wymianę ciepła.
-
A Method for Optimising the Blade Profile in Kaplan Turbine
PublicationThis paper introduces a method of blade profile optimisation for Kaplan-type turbines, based on modelling the interaction between rotor and stator blades. Rotor and stator blade geometry is described mathematically by means of a midline curve and thickness distribution. Genetic algorithms are then used to find a global optimum that minimises the loss coefficient. This allows for variety of possible blade shapes and configurations....
Year 2020
-
A Comparison of Empirical Correlations of Viscosity and Thermal Conductivity of Water-Ethylene Glycol-Al2O3 Nanofluids
PublicationBecause of their superb thermal conductivity, nanofluids are seen as new generation of cooling mediums in many engineering applications. It is well established that even a small amount of nanoparticles mixed with a base fluid may result in distinct thermal conductivity enhancement. On the other hand, addition of nanoparticles to the base fluid results in its substantial viscosity increase. Therefore, it is very dicult to evaluate...
-
A concept of zero-dimensional and three-dimensional thermodynamic modelling of steam storage in a steam cycle
PublicationThis work presents the thermodynamic model of steam storage in a steam cycle. The innovative steam storage is an integral part of the unit and thus responds quickly to changes in load. This enhances the primary control reserve while maintaining high efficiency of energy conversion. With regard to power plants, it improves the operational safety of generation units, as it prevents boiler and turbines overload in the case of steep...
-
A new construction of shell-and-tube heat exchanger with impinging jets and minichannels technologies for heat recovery from gases – experimental analysis
PublicationA dynamic development of technologies allowing waste heat utilization is observed in a correspondence with a pro-ecological approach of the zero waste idea. Such approach becomes the most demanding in the area of low-temperature was heat sources, especially gaseous media. Till now, they were usually not utilized due to unfavorable thermal conditions and high costs. Therefore, the zero waste approach directs research on techniques...
-
A novel concept of negative CO2 emission power plant for utilization of sewage sludge
PublicationCarbon Capture and Storage (CSS) technology is considered an important “bridge technology”, allowing effective abatement of CO2 emissions for power units using fossil fuels. However, if biomass is used in a power plant, equipped with CCS system, negative CO2 emissions can be achieved. In practice, wide development of such technologies would enable not only reduction of CO2 emissions, but also reversal of the harm done so far. In...
-
A Theoretical and Experimental Study of Moderate Temperature Alfa Type Stirling Engines
PublicationThe Stirling engine is a device that allows conversion of thermal energy into mechanical energy with relatively high efficiency. Existing commercial designs are mainly based on the usage of high temperature heat sources, whose availability from renewable or waste heat sources is significantly lower than that of moderate temperature sources. The paper presents the results of experimental research on a prototype alpha type Stirling...
-
Advanced Turbine Cycles with Organic Media
PublicationOrganic Rankine Cycle (ORC) power plants have become very popular and have found their applications in systems with renewable sources of energy. So far their overall efficiencies are not very impressive and only for the upper temperature of about 300 °C do they exceed 20%. A drawback of these cycles is the limitation of the cycle upper temperature due to the heat exchanger technology and the materials used. However, it is possible...
-
Air-cooled photovoltaic roof tile as an example of the BIPVT system – An experimental study on the energy and exergy performance
PublicationThe air-cooled photovoltaic tile is a subject of presented investigations, which focused on improving the overall system efficiency of PV tiles with heat recovery. The operational efficiency of a PV roof tile, together with the construction optimising the air cooling efficiency, were the main points of plans realized at this research stage. The article describes the experimental research consisting of the assessment of electrical,...
Year 2019
-
A model development and experimental verification for a vapour microturbine with a permanent magnet synchronous generator
PublicationVapour microturbines with permanent magnet synchronous generators are implemented in micropower plants for dispersed power generation systems. The dynamic model of such a microturbine set was developed and presented. The developed relations result from the generic equations. Experimental data for two different working medium were used for model verification. A microturbine set model was tested during the changes in the parameters...
-
A numerical analysis of the thermal effects in the jet impingement stagnation zone
PublicationMost of the flows occurring in the engineering systems are turbulent and their accurate numerical analysis is still challenging, especially when combined with the heat transfer. One of the methods of heat transfer enhancement is utilization of the turbulent impinging jets, which were recently applied also in the heat exchangers. Their positive impact on the heat transfer performance was proven, but many questions related to its...
-
A semi-empirical model for flow boiling heat transfer with account of the reduced pressure effect
PublicationIn the present study the attention was focused on the influence of reduced pressure on the predictions of heat transfer during flow boiling at the extensive range of pressures. The results of calculations were to test the sensitivity of the in-house flow boiling model with respect to the selection of the appropriate two-phase flow multiplier, which is one of the distinctive elements of that model. For this purpose a few two-phase...
-
A study of a compact high-efficiency zero-emission power plant with oxy-fuel combustion
PublicationThis paper discusses the application of global trends in gas cycles technology using oxy-fuel combustion. This is followed by a demonstration of a design solution for a new cycle with two enhanced energy-converting devices, namely a wet combustion chamber and a spray-ejector condenser. The proposed gas and steam cycle unit is contained within a single turbine, whose benefits combine those offered by gas turbines (high inlet temperatures)...
-
A unified approach to the analysis of electric energy and fuel consumption of cars in city traffic
PublicationForecasting fuel and electricity consumption is an important factor determining the direction of changes in road engineering solutions, traffic management, selection of routes for public transport and development more efficient car drive systems. With a reliable and easy-to-use computational tool, it is possible to reduce the consumption of primary energy sources and reduce the emission of toxic compounds in cities. An analysis...
Year 2009
-
A multistage turbine for a micro power plant
PublicationThis paper presents results of a design analysis of a multi-stage turbine for the cogeneration micro-power plant working in accordance with Organic Rankine Cycle (ORC). The heat power of the plant is assumed equal to 20 kW and the corresponding available electric output is estimated to be of about 3 kW. Different variants of the radial and axial-flow turbines have been considered, while the detailed results of the calculations...
-
A new method for determination of flow boiling heat transfer coefficient in conventional diameter channels and minichannels
PublicationW pracy przedstawiono rozważania związane z modelowaniem wrzenia w przepływie w kanałach o średnicach konwencjonalnych, małych i minikanałach. Przedstawiono przegląd podejść do modelowania wymiany ciepła i w tym świetle przedstawiono oryginalne podejście autora. W przeciwieństwie do innych podejść metoda autora ma zastosowanie zarówno do kanałów o średnicach konwencjonalnych i minikanałach. Przedstawiono zadowalające porównania...
Year 2018
-
A New Approach for the Mitigating of Flow Maldistribution in Parallel Microchannel Heat Sink
PublicationThe problem of flow maldistribution is very critical in microchannel heat sinks (MCHS). It induces temperature nonuniformity, which may ultimately lead to the breakdown of associated system. In the present communication, a novel approach for the mitigation of flow maldistribution problem in parallel MCHS has been proposed using variable width microchannels. Numerical simulation of copper made parallel MCHS consisting of 25 channels...
-
A simplified energy dissipation based model of heat transfer for post-dryout flow boiling
Publicationmodel for post dryout mist flow heat transfer is presented based on considerations of energy dissipation in the flow. The model is an extension of authors own model developed earlier for saturated and subcooled flow boiling. In the former version of the model the heat transfer coefficient for the liquid singlephase convection as a reference was used, due to the lack of the appropriate model for heat transfer coefficient for the...
-
A universal NDT method for examination of low energy impact damage in CFRP with the use of TLC film
PublicationThe article presents an attempt to use a sheet of laminated thermochromic liquid crystal film (TLC film) for non-destructive testing of the impact damage (energy values: 1J, 2J, 3J and 4J) in carbon fibre-reinforced polymer (CFRP). This is a new, alternative NDT approach based on the thermo-optical effect. The main advantages of this method are a) the low cost of TLC film, b) the low cost of recording devices due to the usage of...
Year 2005
-
A new integrated curriculum for computational methods in mechanics and design
PublicationPrzedstawiono program nowej specjalności na studiach inżynierskich: metody numeryczne w mechanice i projektowaniu, prowadzonej w języku angielskim.
-
A nonlinear approach to modelling gas bubble deformation.
PublicationPrzedstawiono model wyjaśniający wpływ deformacji pęcherzyka na występowanie zjawiska chaosu podczas generowania pęcherzyków gazowych z pojedynczej dyszy zanurzonej w cieczy.
-
A semi-empirical method for calculation of heat transfer coefficient in flow boiling for conventional tubes and minichannels
PublicationW pracy przedstawiono zagadnienia któe należy uwzględnić podczas modelowania wymiany ciepła z wrzeniem w przepływie w kanałach o małej średnicy. Uzyskano dobrą zgodność z wynikami badań eksperymentalnych.
Year 2022
-
A new method of wind farm active power curve estimation based on statistical approach
PublicationThe purpose of this paper is to solve the wind farm active power estimation problem, introducing the method which is based on a statistical approach and robust fitting. The proposed algorithm uses a statistical approach and compared to existing ones- includes a wind direction as well as the influence of turbine start-up procedure on the estimation. The results show that additional estimation inputs i.e. the wind direction and the...
Year 2016
-
A novel concept of H2/O2 steam generator
PublicationThis paper presents an idea of hydrogen utilization to steam generation to drive a turbine and produce electricity or to supply a condenser as an element of a heating system. Electrolysis process is considered as a source of hydrogen as well as oxygen. Hydrogen combustion with a stoichiometric ratio of pure oxygen produces steam at very high temperature. Steam temperature can be controlled by mixing the generated steam with liquid...
-
A NOVEL CONCEPT OF H2/O2 STEAM GENERATOR
PublicationThis paper presents an idea of hydrogen utilization to steam generation to drive a turbine and produce electricity or to supply a condenser as an element of heating system. Electrolysis process is considered as a source of hydrogen as well as oxygen. Hydrogen combustion with a stoichiometric ratio of pure oxygen produces steam at very high temperature. Steam temperature can be controlled by mixing the generated steam with liquid...
-
Accuracy Investigations of Turbine Blading Neural Models Applied to Thermal and Flow Diagnostics
PublicationPossibility of replacing computional fluid dynamics simulations by a neural model for fluid flow and thermal diagnostics of steam turbines is investigated. Results of calculations of velocity magnitude of steam for 3D model of the stator of steam turbine is presented.
-
Acoustic journal bearing – Performance under various load and speed conditions speed conditions
PublicationThe paper presents results of experimental testing aiming at finding out what effect system of piezo-electric actuators (PZTs)attached to an aerodynamic journal bearing has on the magnitude of shaft's motion within the bearing operating at specified speed and load. The results clearly demonstrate effectiveness of PZTs in mitigating the shaft's motion thus contributing to the increased stability of the bearing. This stabilizing...
Year 2013
-
A PROPOSAL OF A DESCRIPTION OF THE OPERATING CONDITIONS OF DIESEL-ELECTRIC LOCOMOTIVES
PublicationThe paper presents a proposal of a description of the operating conditions of diesel-electric locomotives. The proposal is a result of the operational experience and the analysis of the locomotive operation. It constitutes a significant simplification in relation to the descriptions currently used by domestic carriers. The paper also presents examples of analyses of the operating conditions of locomotives using the proposed method.
-
A simple approach to heat exchanger sizing optimisation by means of entrophy generation minimisation
PublicationIn the paper an attempt is presented to find the method of optimization of microtube diameter with respect to optimal thermal-hydraulic conditions in the single-phase shell-and-tube heat exchangers. The approach is based on consideration of pumping power at the condition of maximum heat transfer by the heat exchanger tube system. In the optimization method the tube diameter is first specified and then appropriate calculations are...
Year 2006
-
A semi-empirical method for calculation of flow boiling heat transfer coefficients for conventional channels and small diameter tubes
PublicationW pracy przedstawiono rozważania na temat modelowania dwufazowego przepływu wrzącego w kanałach konwencjonalnych i w kanałach o małej średnicy. Przedstawiono modyfikację korelacji zaproponowanej wcześniej przez J. Mikielewicza na podstawie nowych danych eksperymentalnych, uzyskanych dla kanałów o małej średnicy. Bank danych obejmował ponad 460 punktów pomiarowych dla czynników R141b, R134a, R113, R123, R12, R11 i wody. Uzyskano...
-
A semi-empirical method for calculation of heat transfer coefficient in flow boiling for conventional tubes and minichannels
PublicationW pracy przedstawiono zagadnienia które należy uwzględnić podczas modelowania wymiany ciepła z wrzeniem w przepływie w kanałach o małej średnicy. Uzyskano dobrą zgodność z wynikami badań eksperymentalnych.
Year 2017
-
A SHORT REVIEW OF BLOOD FLOW MODELLING METHODS: FROM MACRO- TO MICROSCALES
PublicationThe aim of this paper it to review various scale approaches to the blood flow modelling. Blood motion may be described by three types of mathematical models according to the observed scales or resolutions, namely microscopic, mesoscopic and macroscopic descriptions. The above approaches are discussed together with their advantages and disadvantages. Several results of mesoscopic simulations are presented with particular attention...
-
A simplified energy dissipation based model of heat transfer for subcooled flow boiling
PublicationIn the paper a model is presented based on energetic considerations for subcooled flow boiling heat transfer. The model is the extension of authors own model developed earlier for saturated flow boiling and condensation. In the former version of the model we used the heat transfer coefficient for the liquid single-phase as a reference level, due to the lack of the appropriate model for heat transfer coefficient for the subcooled...
-
Algorytmy genetyczne i ewolucyjne
PublicationAlgorytmy ewolucyjne istnieją dzięki wieloletnim obserwacją procesów zachodzących wśród żywych organizmów. Korzystają one z nazw i określeń występujących w genetyce np.: gen, chromosom. Algorytmy genetyczne oraz ewolucyjne używa się w procesach optymalizacyjnych w celu poszukiwania ekstremów.
Year 2008
-
A simple model of circular hydraulic pump
PublicationRozpatrzono warunki powstawania osiowosymetrycznego uskoku hydraulicznego. Przedstawiono model, w którym rozpatrzono obecność dodatkowych strat w równaniu Bernoulliego. Przyczyniają się one do powstawania dodatkowego wiru w miejscu uskoku. Porównanie z wynikami badań eksperymentalnych potwierdza słuszność przyjętych tez.
-
A study of flow boiling heat transfer in minichannels
PublicationW pracy przedstawiono badania eksperymentalne wrzenia w przepływie w minikanale o średnicy wewnętrznej 2.3mm i długości 38cm. Uzyskano rozłady temperatury wzdłuż ścianki kanału oraz lokalne współczynniki przejmowania ciepła. Dane skorelowano z korelacją półempiryczną uzyskując zadowalającą zgodność.