- wersja autorska artykułu przed recenzją
- wersja autorska artykułu po recenzji
Tabela statusów SHERPA RoMEO
|SHERPA RoMEO kolor||Polityka archiwizacji|
|Zielony||można archiwizować pre-printy i post-printy lub wersję wydawcy|
|Niebieski||can archive post-prints|
|Żółty||można archiwizować pre-printy|
|Biały||nie można archiwizować żadnych materiałów|
Współczynnik Impact Factor
Zaloguj się aby zobaczyć Współczynnik Impact Factor dla tego czasopisma
- Politechnika Gdańska
Prace opublikowane w tym czasopiśmie
- wyników na stronę:
2-D constitutive equations for orthotropic Cosserat type laminated shells in finite element analysisPublikacja
We propose 2-D Cosserat type orthotropic constitutive equations for laminated shells for the purpose of initial failure estimation in a laminate layer. We use nonlinear 6-parameter shell theory with asymmetric membrane strain measures and Cosserat kinematics as the framework. This theory is specially dedicated to the analysis of irregular shells, inter alia, with orthogonal intersections, since it takes into account the drilling...
A new type of (TiZrNbTaHf)N/MoN nanocomposite coating: Microstructure and properties depending on energy of incident ionsPublikacja
A novel (TiZrNbTaHf)N/MoN nanocomposite coatings, which consist of the nitride of the high-entropy alloy and the binary nitride, were synthesized by vacuum-arc deposition at various substrate biases. The elemental composition, chemical bonding state, phase structure, microstructure and mechanical properties of the coatings were studied by high-resolution experimental methods: SIMS, GDMS, XPS, XRD, HR-TEM and nano-indentation. It...
The majority of fiber reinforced composites exhibit strong non-linear behavior in in-plane shear state. The effect is attributed to the micro-cracks appearing in the matrix and can be modeled on the micro and macro level. In this work the author proposes constitutive laws describing the non-linear in-plane shear response, which can be alternative for the relations commonly considered in the literature. The proposed equations are...
The paper is a continuation of  where the formulation of the elastic constitutive law for functionally graded materials (FGM) on the grounds of nonlinear 6-parameter shell theory with the 6th parameter (the drilling degree of freedom) was presented. Here the formulation is extended to the elasto-plastic range. The material law is based on Cosserat plasticity and employs the well-known Tamura-Tomota-Ozawa (TTO)  mixture...
Modal properties identification of a novel sandwich footbridge – Comparison of measured dynamic response and FEAPublikacja
A modern sandwich composite footbridge made of high-tech materials, being an example of practical application of laminated composites in civil engineering, is presented. The in situ non-destructive testing of the footbridge, aiming to identify modal properties and pedestrian comfort, is described. The measured eigenmodes and eigenfrequencies are compared with numerically estimated values. Finite element analyses of the footbridge...
Preparation and characterization of natural rubber composites highly filled with brewers' spent grain/ground tire rubber hybrid reinforcementPublikacja
Brewers' spent grain (BSG) and ground tire rubber (GTR) were applied as low-cost hybrid reinforcement natural rubber (NR). The impact of BSG/GTR ratio (in range: 100/0, 75/25, 50/50, 25/75 and 0/100 phr) on processing and performance properties of highly filled natural rubber composites was evaluated by oscillating disc rheometer, Fourier-transform infrared spectroscopy, thermogravimetric analysis, scanning electron microscopy,...
A novel sandwich footbridge - Practical application of laminated composites in bridge design and in situ measurements of static responsePublikacja
A novel sandwich composite footbridge is presented in the paper, as an example of practical application of laminated composites in civil engineering. The in situ static load tests of the footbridge before its acceptation for exploitation are shown and discussed. The results are compared with the corresponding ones from a numerical equivalent single layer model of the sandwich structure created within the framework of finite element...
Low velocity impact behaviour of nano-SiO2 enhanced carbon fibre/epoxy composites for naval applications is reported. Epoxy resin matrix was enhanced by 1- 8 wt% SiO2 nanoparticles, based on industrial surface-modified nanosilica. Impact parameters: force, deformation, energy, damage size were recorded. The most pronounced effect was damage size decrease; e.g. ∼28% recorded by infrared thermography and X-ray computed radiography...
Geometrically nonlinear FEM analysis of FGM shells based on neutral physical surface approach in 6-parameter shell theoryPublikacja
The paper presents the formulation of the elastic constitutive law for functionally graded materials (FGM) on the grounds of nonlinear 6-parameter shell theory with the 6th parameter being the drilling degree of freedom. The material law is derived by through-the-thickness integration of the Cosserat plane stress equations. The constitutive equations are formulated with respect to the neutral physical surface. The influence of...
Morphology and mechanical properties of polyamide/clay nanocomposites toughened with NBR/NBR-g-GMA: A comparative studyPublikacja
This work highlights the importance of nanoclay dispersion state in the nanocomposites containing polyamide 6 (PA6), nanoclay and elastomers as well as clay localization at the interface of thermoplastic/elastomer. Morphology and mechanical properties of a series of nanocomposites containing acrylonitrile butadiene rubber (NBR), glycidyl methacrylate-grafted NBR (NBR-g-GMA), and combined NBR/NBR-g-GMA were compared and discussed...
In this paper the process of native starch preparing for modification by extrusion and manufacture of biocomposites is presented. The first aim of this study was to determine the mixing and granulating condition of native starch to obtain granulated native starch. For mixing and granulation of native starch Intensive Mixer manufactured by Maschinenfabrik Gustav Eirich was used. Mixing and granulation in a single process is a new...
Effects of manufacturing and face /core bonding on impact damage in glass/polyester - PVC foam core sandwich panelsPublikacja
Zbadano podatność na inicjację uszkodzeń pod wpływem spadającego obciążenia w konstrukcjach przekładkowych poliestrowo szklanych z rdzeniem z pianki PVC przy dwóch sposobach łączenia okładek z rdzeniem: przy pomocy 2 klejów proponowanych do tego celu przez ich producentów oraz czystej żywicy. Zastosowano oprzyrządowany młot spadowy , określając rozmiar zniszczeń na powierzchni próbki metodą wizualna i ultradźwiękową. Inicjacja...
wyświetlono 114 razy