dr inż. Cezary Szydłowski
Zatrudnienie
- Starszy specjalista naukowo-techniczny w Katedra Inżynierii Transportowej
Obszary badawcze
Publikacje
Filtry
wszystkich: 53
Katalog Publikacji
Rok 2024
-
Consideration of Pseudo Strain Energy in Determination of Fatigue Life and Microdamage Healing of Asphalt Mastics
PublikacjaRest periods between cyclic loads can lead to recovery of damage and extension of fatigue life. This phenomenon is referred to as healing. Healing is clearly observed in bituminous materials, such as asphalt mastics, which belong to the components of asphalt mixtures. Due to the nature of road pavement traffic loading, which is characterized by series of intermittent pulses with rest periods, consideration of healing is necessary...
-
Fracture susceptibility of high RAP content asphalt concrete in terms of aging
PublikacjaDue to the reduction of CO2 emissions during the production of asphalt mixtures and the decrease in the demand for mineral resources, the addition of reclaimed asphalt pavement (RAP) is becoming indispensable. The durability of asphalt pavements containing a high RAP content may be reduced due to a decrease in the cracking resistance of the material, especially under the influence of operational aging. The article presents the...
-
Monte Carlo simulations of the fracture resistance of an asphalt pavement layer
PublikacjaThe purpose of the proposed numerical model is to analyze the cracking of the wearing course in a pavement overlay, assuming a pre-existing crack that passes through the binding layer and base. The computations employed the author's simulation-based Monte Carlo material model, which describes the failure process of a Semi-Circular Bend (SCB) specimen during standard laboratory testing of asphalt concrete. A key feature of this...
-
One year performance evaluation of low volume road with cold recycled base course on the basis of FWD and Dynamic Modulus tests
PublikacjaArticle presents results of assessment of performance of trial section of flexible pavement with cold recycled base constructed on low volume road within typical contract conditions. Performance evaluation was made based on Falling Weight Deflectometer (FWD) test performed during construction stage – 2 times on the top of cold recycled base course – 28 and 180 days after compaction of base course and 2 times on the top of the wearing...
-
The use of a 4 PB strain sweep fatigue test to evaluate characteristics of carbon grid reinforced asphalt beams
PublikacjaThe article presents research results concerning pre-bituminized carbon grids for asphalt pavement reinforcement, which are used to prevent cracking and crack reflection thus increasing bearing capacity and durability of pavement. Research program involved testing of large sized double-layer samples, both reinforced and unreinforced. The advantage of using a carbon grid was especially visible after crack initiation. The energy...
Rok 2023
-
ANALIZA WYBRANYCH CECH MECHANICZNYCH MIESZANEK MINERALNO-CEMENTOWO-EMULSYJNYCH (MCE)
PublikacjaW ostatnich latach mieszanki mineralno-cementowo-emulsyjne (MCE) stają się materia³em coraz częściej wykorzystywanym przy projektowaniu remontów i przebudów nawierzchni z wykorzystaniem recyklingu. Materiał ten zyskuje coraz większą popularność, ponieważ pozwala w sposób racjonalny i bez uszczerbku dla środowiska naturalnego ponownie wykorzystać materiały pochodzące z rozbiórki starych nawierzchni bitumicznych, w tym również materiały...
-
Bitumen-Based Poroelastic Pavements: Successful Improvements and Remaining Issues
PublikacjaThis article presents the development process of designing and testing poroelastic pavement based on highly polymer-modified bitumen. Poroelastic wearing course was composed of mineral and rubber aggregate mixed with highly polymer-modified bitumen, in contrast to previous trials, during which polyurethane resins were mainly used as binder, which led to several serious technological problems concerning difficult production, insufficient...
-
Crack Resistance of Asphalt Concrete Subjected to Environmental Factors
PublikacjaThe paper presents an analysis of the influence of environmental factors on the cracking susceptibility of asphalt concrete resulting in a change in the durability of asphalt pavement. In order to assess the phenomenon, laboratory tests were carried out taking into account the destructive effects of moisture, freeze-thaw cycle and long-term ageing. The influence of both factors occurring simultaneously was also verified. Due to...
-
Monte Carlo simulations of the fracture resistance degradation of asphalt concrete subjected to environmental factors
PublikacjaThe paper presents the results of laboratory tests of SCB (semi-circular beam) samples of asphalt concrete, subjected to the destructive effect of water and frost as well as the aging processes. The determined values of material parameters show significant dispersions, which makes the design of mixtures difficult. Statistical analysis of the test results supplemented by computer simulations made with the use of the proprietary...
-
Stiffness of cold-recycled mixtures under variable deformation conditions in the IT-CY test
PublikacjaStiffness modulus belongs to the most important properties describing the cold-recycled mixtures (CRM) in terms of their usability in road pavement structures. Previous research proved that this property is strongly dependent on the scheme and conditions of the test (temperature and time of loading) and the time that has passed since the compaction of the specimen or pavement layer. It is a result of the influence of two different...
-
The dependence of linear viscoelasticity limits of cold-recycled mixtures on time of curing and compaction method
PublikacjaCold-recycled mixtures are currently among the most widely used and investigated methods that enable recycling of old pavement structures in an environmentally friendly manner. Upon milling, the old pavement structure – whose gradation can be improved with addition of virgin aggregate – is mixed and compacted at ambient temperature. The main binding agents are bituminous emulsion and cement. Due to their dual binding behaviour,...
-
The effect of multiaxial geocomposite reinforcement on fatigue performance and crack propagation delay in double-layered asphalt beams
PublikacjaThe presented study investigates the effect of a recently developed multiaxial geocomposite made of polypropylene geogrid and non-woven fabric on the delay of crack propagation, based on four-point bending tests of large asphalt concrete beams – both for reinforced and non-reinforced specimens. Several approaches are described in this study, including analysis of stiffness modulus decrease and analysis of crack propagation using...
Rok 2022
-
Cold recycled mixtures for binder courses - laboratory evaluation of mechanical properties
PublikacjaCold recycled mixtures composed with cement and bituminous emulsion are nowadays commonly used material for base layer. Typical pavement with cold recycled mixtures usually consists of two asphalt courses (wearing and binding course) constructed over cold recycled base. Therefore the next step in cold recycling is possibility of design of binding courses with recycled materials, but with potential to obtain high quality mixtures...
-
Laboratory fatigue assessment of large geocomposite-reinforced double-layered asphalt concrete beams
PublikacjaGeosynthetic reinforcement of asphalt layers has been used for several decades. Evaluation of the influence of these materials on pavement fatigue life is still ongoing, especially for new types of geocomposites. This paper presents the evaluation of fatigue performance of large asphalt concrete beams reinforced with a new type of composite in which square or hexagonal polypropylene stiff monolithic paving grid with integral junctions...
-
Laboratory fatigue assessment of large geocomposite-reinforced double-layered asphalt concrete beams
PublikacjaGeosynthetic reinforcement of asphalt layers has been used for several decades. Evaluation of the influence of these materials on pavement fatigue life is still ongoing, especially for new types of geocomposites. This paper presents the evaluation of fatigue performance of large asphalt concrete beams reinforced with a new type of composite in which square or hexagonal polypropylene stiff monolithic paving grid with integral junctions...
-
Preliminary study of linear viscoelasticity limits of cold recycled mixtures determined in Simple Performance Tester (SPT)
PublikacjaThe publication presents methodology developed for determination of linear viscoelasticity limits for cold recycled mixtures with cement and bituminous emulsion using Simple Performance Tester (SPT). Methodology was verified on reference materials (PCV and steel dummy specimens, cement concrete and asphalt concrete) to comply with elasticity and viscoelasticity theory. The developed methodology enabled determination of linear viscoelasticity...
-
The use of a two-phase Monte Carlo material model to reflect the dispersion of asphalt concrete fracture parameters
PublikacjaThe work covers comprehensive laboratory tests of semi-circular bending (SCB) of asphalt concrete samples. The results of two test series, including four and 32 SCB specimens, indicate a substantial scatter of force–deflection (F-d) histories. The numerical analysis is aimed to reflect the maximum breaking load and fracture energy of the samples, pointing out their random character. The original simulation-based fictitious Monte...
-
The Use of Direct Shear Test for Optimization of Interlayer Bonding Under a Poroelastic Layer
PublikacjaPoroelastic Road Surfaces (PERS) are characterised by porous structure with air void content of 20% or higher and stiffness almost 10 times lower than that of a standard asphalt course. Such properties enable noise reduction by up to 12 dB in comparison to SMA 11 mixture. However, the disadvantage of a poroelastic pavement is its low durability, which partially results from delamination from the lower layer. The paper aims to investigate...
-
Wpływ zastosowania zbrojenia warstw asfaltowych geosyntetykami na nośność remontowanej nawierzchni drogowej – cz. 1
PublikacjaArtykuł prezentuje efekty rozpoczętego i trwającego programu badawczego, którego celem jest poszukiwanie trwałego i skutecznego rozwiązania wzmocnienia nawierzchni lub remontu nawierzchni, jakim jest zbrojenie nawierzchni drogowych w warstwach asfaltowych geosiatkami z włókien szklanych, szklano-węglowych i węglowych wstępnie przesączonych asfaltem. Siatki te zostały wykorzystane jako zbrojenie warstw asfaltowych na fragmencie...
Rok 2021
-
Assessment of Tensile Strength Reserve of Asphalt Mixtures at Low Temperatures
PublikacjaDuring winter conditions, low-temperature cracks develop at the surface of the asphalt pavement when tensile thermal stress induced in the asphalt layer during cooling equals and exceeds the tensile strength of the material. The paper presents the results of tensile strength reserve assessment of asphalt mixtures with neat and SBS-polymer modified bitumen application. The tensile strength reservewas calculated as difference between...
-
BINDER COURSES USING COLD RECYCLED MIXTURES – A NOVEL CONCEPT IN COLD RECYCLING
PublikacjaCold recycling with cement and bituminous emulsion is one of the most environmentally friendly techniques to maximize the reuse of reclaimed asphalt (RA) collected during demolition of roads. Cold recycled mixtures are commonly used for base courses in construction or rehabilitation of flexible and semi-rigid pavements. Current experiences demonstrated that cold recycling with appropriate requirements and technical recommendations...
-
Comparative Study of the Mechanical Behaviour of Bitumen- and Cement-Dominated Mixtures with Reclaimed Asphalt
PublikacjaThe bitumen emulsion-based recycling is a commonly used maintenance treatment in the rehabilitation of low-and medium-volume roads in Europe. Nevertheless, the wide range of climatic conditions across the continent resulted in the variety of mixture concepts and the requirements being adopted for various local conditions. In this regard, the most commonly used parameter to distinguish between the main mixture concepts is bitumen...
-
Fatigue Performance of Double-Layered Asphalt Concrete Beams Reinforced with New Type of Geocomposites
PublikacjaThe reinforcement of asphalt layers with geosynthetics has been used for several decades, but proper evaluation of the influence of these materials on pavement fatigue life is still a challenging task. The presented study investigates a novel approach to the reinforcement of asphalt layers using a new type of geogrid composite, in which square or hexagonal polypropylene stiff monolithic paving grid with integral junctions is bonded...
-
Optimisation and field assessment of poroelastic wearing course bond quality
PublikacjaCompared to typical asphalt mixtures, poroelastic mixtures are characterised by high porosity and high flexibility, which are desirable for traffic noise reduction. However, the same properties increase the risk of debonding from the lower layer, which is a significant source of premature damage. The study investigates which of the factors – tack coat agent, type and texture of the lower layer – have the greatest impact on interlayer...
-
The Influence of Cement Type on Early Properties of Cold In-Place Recycled Mixtures
PublikacjaCold in-place recycling is a commonly used maintenance treatment in rehabilitation of low and medium volume roads in Poland. Typically, two types of binding agents are used—cement and bituminous emulsion (or foamed bitumen).Due to the harsh Polish climate with many freeze/thaw cycles and frequent occurrence of saturated conditions, the used amounts of cement are higher than those commonly used in warmer parts of Europe. While there...
Rok 2020
-
Design of poroelastic wearing course with the use of direct shear test
PublikacjaPoroelastic Road Surfaces (PERS) are characterized by porous structure with at least 20% of air void content and stiffness almost 10 times lower than typical asphalt course. Such properties enable noise reduction up to 12 dB in comparison to SMA 11 mixture. However, the main disadvantage of previously used poroelastic mixtures, based on resin type binders, was their low durability, which resulted in raveling and delamination from...
-
Influence of Selected Warm Mix Asphalt Additives on Cracking Susceptibility of Asphalt Mixtures
PublikacjaWarm mix asphalt (WMA) has been widely accepted as a future asphalt paving technology. Besides clear advantages, there are still some concerns regarding durability and long-term performance of pavements made with this type of asphalt mixtures. One of the most important issues is low temperature behaviour of WMA because certain additives used for temperature reduction can aect bitumen properties. This paper presents the evaluation...
-
Initial Field Validation of Poroelastic Pavement Made with Crumb Rubber, Mineral Aggregate and Highly Polymer-Modified Bitumen
PublikacjaTire/road noise in most driving conditions dominates other sources of traffic noise. One of the most efficient ways of reducing tire/road noise is to use the so-called “low noise pavement”. According to numerous studies, at present, poroelastic road pavement that is composed of rubber and mineral aggregate and polyurethane or bituminous binder gives the best noise reduction up to 12 dB. Unfortunately, there are many problems with...
-
The influence of combination of binding agents on fatigue properties of deep cold in-place recycled mixtures in Indirect Tensile Fatigue Test (ITFT)
PublikacjaThe publication presents fatigue properties of cold recycled mixtures for eight combinations of binding agents (cement and bituminous emulsion). Cold recycled mixtures were evaluated in Indirect Tensile Fatigue Test (ITFT) at the temperature of 20 C in controlled stress mode. As a function of horizontal stress, fatigue life is strongly influenced by combination of the binding agents. When fatigue life is analyzed as a function...
Rok 2019
-
Assessment of Thermal Stresses in Asphalt Mixtures at Low Temperatures Using the Tensile Creep Test and the Bending Beam Creep Test
PublikacjaThermal stresses are leading factors that influence low-temperature cracking behavior of asphalt pavements. During winter, when the temperature drops to significantly low values, tensile thermal stresses develop as a result of pavement contraction. Creep test methods can be suitable for the assessment of low-temperature properties of asphalt mixtures. To evaluate the influence of creep test methods on the obtained low-temperature...
-
Evaluation of the stiffness modulus and phase angle of cold in-place recycled mix-tures for long curing periods
PublikacjaArticle presents the changes inbehaviour of cold-in place recycling mixtures made using cement and bituminous emulsion (CIR mixtures) after anelongated time of curing. Most of the available literatureregarding change instiffness modulus and phase angle presents resultsfor a maximum of several dozen days,which makesit difficult to predict the behaviour over the whole life of the compacted layer. The article...
-
Influence of cooling rate and additives on low-temperature properties of asphalt mixtures in the TSRST
PublikacjaThe paper presents the results and analysis of low-temperature properties of asphalt mixtures according to Thermal Stress Restrained Specimen Test (TSRST) and Indirect Tensile Test methods. Different groups of bitumen were investigated: neat, SBS-modified and highly SBS-modified. Influence of cooling rates (1 C/h, 3 C/h, 5 C/h and 10 C/h) and additives (aramid fibres and crumb rubber) was identified as well. Moreover, for each...
-
NON-LINEAR MASTIC CHARACTERISTICS BASED ON THE MODIFIED MSCR (MULTIPLE STRESS CREEP RECOVERY) TEST
PublikacjaMastic containing asphalt in its composition is an example of a viscoelastic material. It is an effective binder in asphalt. It consists of a filler (<0.063 mm) and asphalt mixed in the right proportions. Just like in asphalt, its response depends on the temperature level, the load and stress time. Changing the stress stiffness of the mastic affects the non-linear course of the stress-strain relationship. Modelling of the non-linear...
-
The statistical impact of experimental result scatter of asphalt mixtures on their numerical modelling
PublikacjaThe paper presents selected test results of asphalt mixture conducted in low temperatures. The obtained parameters are highly diverse. It concerns ultimate breaking loads, stiffness parameters related to Young's modulus but also the fracture course. Statistical analysis upon the results makes it possible to relevantly estimate the material-defining parameter values. Such a random approach leads to the mean values of breaking and...
Rok 2018
-
A material model of asphalt mixtures based on Monte Carlo simulations
PublikacjaThe paper aims to numerically reflect mineral-asphalt mixture structure by a standard FEM software. Laboratory test results are presented due to bending tests of circular notched elements. The result scatter is relatively high. An attempt was made to form a random aggregate distribution in order to obtain various results corresponding to laboratory tests. The material structure calibration, its homogenization and finite element...
-
Badanie wpływu rodzaju asfaltu na odporność mieszanek mineralno-asfaltowych na spękania odbite z wykorzystaniem urządzenia Texas Overlay Tester (TxOT)
PublikacjaSpękania są jednym z głównych rodzajów zniszczeń występujących w nawierzchniach asfaltowych, zwłaszcza w przypadku starych nawierzchni, które zostały wzmocnione nowymi warstwami asfaltowymi – nakładką. Mieszanki mineralno-asfaltowe stosowane w takich przypadkach powinny być tak zaprojektowane, aby zapewniały wysoką odporność nowych warstw na spękania odbite. Jednym z czynników minimalizujących ryzyko wystąpienia...
-
Evaluation of Asphalt Mixture Low-Temperature Performance in Bending Beam Creep Test
PublikacjaLow-temperature cracking is one of the most common road pavement distress types in Poland. While bitumen performance can be evaluated in detail using bending beam rheometer (BBR) or dynamic shear rheometer (DSR) tests, none of the normalized test methods gives a comprehensive representation of low-temperature performance of the asphalt mixtures. This article presents the Bending Beam Creep test performed at temperatures from −20...
-
Influence of Bitumen Type and Asphalt Mixture Composition on Low-Temperature Strength Properties According to Various Test Methods
PublikacjaIn regions with low-temperatures, action transverse cracks can appear in asphalt pavements as a result of thermal stresses that exceed the fracture strength of materials used in asphalt layers. To better understand thermal cracking phenomenon, strength properties of different asphalt mixtures were investigated. Four test methods were used to assess the influence of bitumen type and mixture composition on tensile strength properties...
-
Influence of bitumen type on cracking resistance of asphalt mixtures used in pavement overlays
PublikacjaCracking is one of the predominant distresses occurring in flexible pavements, especially in old pavements that were rehabilitated with an asphalt overlay. In such cases asphalt mixtures should be designed to ensure high resistance to reflective cracking because new asphalt layers are exposed to existing cracks of the old pavement. The nature of these cracks can be various (transverse, longitudinal as well as crazy cracking). One...
-
Numerical simulation of asphalt mixtures fracture using continuum models
PublikacjaThe paper considers numerical models of fracture processes of semi-circular asphalt mixture specimens subjected to three-point bending. Parameter calibration of the asphalt mixture constitutive models requires advanced, complex experimental test procedures. The highly non-homogeneous material is numerically modelled by a quasicontinuum model. The computational parameters are averaged data of the components, i.e. asphalt, aggregate...
-
The Impact of Long-Time Chemical Bonds in Mineral-Cement-Emulsion Mixtures on Stiffness Modulus
PublikacjaDeep cold in-place recycling is the most popular method of reuse of existing old and deteriorated asphalt layers of road pavements. In Poland, in most cases, the Mineral-Cement-Emulsion mixture technology is used, but there are also applications combining foamed bitumen and cement. Mineral-Cement-Emulsion mixtures contain two different binding agents – cement as well as asphalt from the asphalt emulsion. Asphalt creates asphalt...
Rok 2017
-
Effect of polymer fibres reinforcement on selected properties of asphalt mixtures
PublikacjaThe paper presents selected results of the research program concerning fibre reinforced asphalt concrete. Aramid-polyalphaolefin fibres was used in this study. Selected properties responsible for low temperature cracking and resistance to permanent deformation are presented in this paper. Low temperature cracking susceptibility was evaluated with the results obtained from bending test of rectangular beams with constant rate of...
-
Ekspertyza na temat określenia przyczyn powstania spękań poprzecznych nawierzchni
PublikacjaCelem opracowania jest określenie prawdopodobnych przyczyn powstania spękań poprzecznych przy dylatacjach obiektów inżynierskich położonych w ciągu odcinków drogi ekspresowej S8 oraz drogi krajowej nr 63, których przebudowa była objęta kontraktem „Przebudowa do parametrów drogi ekspresowej S8, odcinek Wyszków-Białystok, odc. Jeżewo-Choroszcz-Białystok, obw. m. Zambrów i m. Wiśniewo.” Zakres ekspertyzy obejmował analizę dokumentacji...
-
Evaluation of Low Temperature Properties of Rubberized Asphalt Mixtures
PublikacjaThe paper presents low-temperature test results of asphalt mixtures designed with use of bitumen modified by crumb rubber and also SBS polymer. Laboratory tests were conducted on two types of asphalt mixtures for wearing course – stone matrix asphalt (SMA 8) and porous asphalt (PA 8). This paper presents results of the following laboratory tests at low temperatures: TSRST test, three point bending creep test, fracture toughness...
-
Ocena odporności na pękanie podbudów drogowych z mieszanek mineralno-cementowo-emulsyjnych (MCE)
PublikacjaPodbudowy z mieszanek mineralno-cementowo-emulsyjnych (MCE) są jednym z wielu materiałów stosowanych do wykonywania warstw nawierzchni w ramach przebudów dróg w Polsce. Mieszanki MCE pozwalają na maksymalne powtórne wykorzystanie istniejących warstw konstrukcyjnych do budowy lub przebudowy nawierzchni. Do wykonania podbudów z MCE stosuje się materiał pochodzący z rozbiórki istniejących warstw (destrukt) bitumicznych, warstw związanych...
-
Ocena właściwości niskotemperaturowych mieszanek mineralno-asfaltowych z asfaltem modyfikowanym SBS i gumą
PublikacjaW artykule przedstawiono wyniki badań przeprowadzonych w niskich temperaturach dla mieszanek mineralno-asfaltowych zaprojektowanych z użyciem asfaltów modyfikowanych miałem gumowym oraz polimerem SBS. Badania laboratoryjne zostały przeprowadzone dla dwóch rodzajów mieszanek mineralno-asfaltowych do warstwy ścieralnej – mastyksu grysowego (SMA 8) i asfaltu porowatego (PA 8). W niniejszym artykule przedstawiono wyniki następujących...
-
The Influence of Binding Agents on Stiffness of Mineral-cement-emulsion Mixtures
PublikacjaThis paper attempts to determine the behavior of mineral-cement-emulsion mixture (MCE) under load, whether is it similar to asphalt mixtures (viscoelastic behavior) or to cement treated materials (elastic behavior). To answer this question nine mineral- cement-emulsion mixtures with different combinations of cement and emulsion content were tested in laboratory using Simple Performance Test (SPT). For each mixture stiffness moduli...
-
The long-term properties of mineral-cement-emulsion mixtures
PublikacjaThis publication presents evaluation of long-term behavior of mineral-cement-emulsion (MCE) mixtures. MCE mixtures are among the major products of cold recycling of old asphalt pavements. They are composed by binding of the old materials reclaimed from the pavement and new mineral aggregate using two different binding agents – cement and bituminous emulsion. While bituminous emulsion dissolutes and binds materials quite fast, it...
-
Wpływ zawartości środków wiążących na sztywność mieszanek mineralno-cementowo-emulsyjnych
PublikacjaW artykule podjęto próbę ustalenia, i jest zachowanie się mieszanek mineralno-cementowo-emulsyjnych (MCE). Czy pod obciążeniem jest bardziej zbliżone do mieszanek mineralno-asfaltowych (materiały o charakterze lepkosprężystym) czy też mieszanek związanych cementem (materiały o charakterze sprężystym). Przebadano dziewięć mieszanek mineralno-cementowo-emulsyjnych o zróżnicowanych kombinacjach obu środków wiążących – cementu oraz...
-
Wpływ zbrojenia polimerowymi włóknami rozproszonymi na wybrane właściwości mieszanek mineralno-asfaltowych
PublikacjaW artykule przedstawiono wybrane wyniki badań mieszanek mineralno-asfaltowych zbrojonych polimerowymi włóknami rozproszonymi. Ocenie poddano mieszankę włókien zbrojących aramidowo-poliolifenowych pod kątem wpływu ich zastosowania na właściwości niskotemperaturowe i odporności na deformacje trwałe mieszanek mineralno-asfaltowych. Właściwości niskotemperaturowe oceniano na podstawie testu zginania próbek belkowych oraz na podstawie...
wyświetlono 2128 razy