prof. dr hab. inż. Kazimierz Darowicki
Publikacje
Filtry
wszystkich: 435
Katalog Publikacji
Rok 2024
-
Validation of dynamic electrochemical impedance spectrograms using autocorrelation function
PublikacjaValidation of impedance data is essential for checking the reliability of experimental data. Kramers – Kronig transformation is used to verify data obtained from classical Electrochemical Impedance Spectroscopy (EIS) measurements. Data obtained from Dynamic Electrochemical Impedance Spectroscopy (DEIS) could be validated in the same way, but in this case, there is no information about internal consistency between every single spectrum...
-
Wet H2S corrosion and degradation of pipeline in amine regeneration system
PublikacjaThe paper presents the results of NDT examinations, metallographic tests and risk assessment of degradation related to corrosion of amine regeneration unit in a desulphurisation system. Intensive corrosion resulting from acid gases environment upon water condensation causes perforation of the pipeline. Detailed analysis reveals cracking related to the mechanism of wet H2S. Hydrogen penetration, resulting from the wet H2S process,...
Rok 2023
-
Application of galvanodynamic impedance spectroscopy for studying passive film cracking under mechanical strain
PublikacjaThe paper reports the results of simultaneous mechanical and electrochemical investigations on austenitic (18/8) stainless steel in a 2 % solution of sulphuric acid. The measurements were performed using Galvanodynamic Electrochemical Impedance Spectroscopy (GDEIS). Electrochemical analysis of mechanical passive layer cracking and repassivation conditions during a tensile test was carried out. Application of this methodology allowed...
-
Badania skuteczności ochrony katodowej zbiornika CWU typu HPMD-01.02.00
PublikacjaZbadano skuteczność ochrony katodowej wewnętrznej powierzchni zbiornika realizowanej w technologii z zewnętrznym źródłem prądu, z zastosowaniem dwóch typów tytanowych anod polaryzacyjnych.
-
Corrosion mechanisms in columns for atmospheric distillation of crude oil
PublikacjaThe paper presents the most common corrosion processes occurring in the columns for atmospheric distillation of crude oil. It describes the mechanisms leading to formation of the chemical compounds, which contribute to corrosion phenomena. The main technological factors influencing corrosion processes have been indicated. The paper also presents the interactions between particular corrosion mechanisms resulting in acceleration...
-
Effect of wet Hydrogen Sulfide on Carbon Steels Degradation in Refinery Based on Case Study
PublikacjaMaterial degradation caused by wet hydrogen sulfide (Wet H2S) is one of the major issues in refineries. Carbon steel is the main construction material used in refineries and is subjected not only to thickness loss but the hydrogen is the major concern. H2S leads to high atomic hydrogen penetration in steel which causes degradation in the form of blistering and/or cracking (HIC/SOHIC) and stress cracking in the area of welds and...
-
Polynomial analysis as a new way of describing dynamic impedance spectra – Differential and relative impedance spectra
PublikacjaModel measurements of an equivalent electrical system were carried out using the technique of Dynamic Electrochemical Impedance Spectroscopy. The measurement took the form of potentiodynamic changes imposed on the tested system. Using the possibility of continuous impedance measurements, an attempt was made to develop an original and innovative method of analyzing impedance spectrograms, which is termed polynomial analysis. As...
-
Sensing the onset of epoxy coating degradation with combined Raman spectroscopy/atomic force microscopy/electrochemical impedance spectroscopy
PublikacjaThe paper presents the results of investigation on epoxy resin durability upon 12-week exposure to UV radiation. The aim was early determination of the onset of epoxy degradation and for this purpose an epoxy film on steel substrate systems were periodically inspected using Raman spectroscopy, atomic force microscopy and electrochemical impedance spectroscopy. The behaviour of examined polymer could be divided into three periods: immunity,...
-
The Effect of Sodium Tetrafluoroborate on the Properties of Conversion Coatings Formed on the AZ91D Magnesium Alloy by Plasma Electrolytic Oxidation
PublikacjaMagnesium and its alloys are widely used in many areas because of their light weight, excellent dimensional stability, and high strength-to-weight ratio. However, the material exhibits poor wear and corrosion resistance, which limits its use. Plasma electrolytic oxidation (PEO) is an effective surface modification method for producing ceramic oxide layers on Mg and their alloys. The influence of the additions of sodium tetrafluoroborate...
Rok 2022
-
Actual field corrosion rate of offshore structures in the Baltic Sea along depth profile from water surface to sea bed
PublikacjaThe paper presents the results of field electrochemical investigations on the corrosion rate of carbon steel in seawater of the Baltic Sea at the location of the Baltic Beta production rig. The measurements were conducted throughout the year in seawater at different depths from the sea surface to the sea bed (about 75 m). The results revealed corrosion aggressiveness of the seawater along the entire depth profile. There was...
-
Korozja w środowisku ropy naftowej. Czynniki i monitorowanie
PublikacjaPrzedstawiono analizy właściwości ropy naftowej z punktu widzenia zawartych w niej czynników korozyjnych oraz ich wpływu na korozję stali w trakcie procesu destylacji ropy naftowej. Krytycznej analizie poddane zostały możliwości oferowane przez współczesne techniki pomiarowe. Wskazano na istotność prowadzenia kompleksowego programu oceny ropy, monitorowania korozji oraz stosowania ochrony inhibitorowej w celu ochrony instalacji...
-
Nowy system monitoringu korozji zastosowany w zakładzie produkcyjnym PKN Orlen SA
PublikacjaPrzedstawiono efekty projektu badawczo-rozwojowego związanego z opracowaniem, budową oraz wdrożeniem monitoringu korozji pracującego w trybie online. Opracowana przez PKN Orlen i Politechnikę Gdańską nowa technologia łączy funkcje monitoringu intensywności korozji ogólnej oraz kruchości wodorowej. Jednoczesny pomiar online kluczowych parametrów pozwala uzyskać zdolność szybkiej oceny postępowania procesu korozji oraz reakcji na...
-
Powłoki malarskie w ochronie przeciwkorozyjnej. Zasady stosowania i kontrola jakości
PublikacjaW książce przedstawiono podstawowe zasady wykonywania i kontroli jakości przeciwkorozyjnych wymalowań malarskich na konstrukcjach stalowych. Opracowanie powstało na bazie wykładów i zajęć praktycznych dla studentów Wydziału Chemicznego Politechniki Gdańskiej prowadzonych przez Katedrę Elektrochemii, Korozji i Inżynierii Materiałowej oraz realizowanych w ramach prac Katedry od około 12 lat kursów dla inspektorów powłok malarskich....
-
The Effect of Sodium Tetrafluoroborate on the Properties of Conversion Coatings Formed on the AZ91D Magnesium Alloy by Plasma Electrolytic Oxidation
Publikacja
Rok 2021
-
Assessment of Fuel Cells’ State of Health by Low-Frequency Noise Measurements
PublikacjaWe proposed applying low-frequency (flicker) noise in proton-exchange membrane fuel cells under selected loads to assess their state of health. The measurement set-up comprised a precise data acquisition board and was able to record the DC voltage and its random component at the output. The set-up estimated the voltage noise power spectral density at frequencies up to a few hundred mHz. We observed the evolution of the electrical...
-
Badania skuteczności ochrony katodowej Nabrzeża Zachodniego odcinek nr 1 (południowy) oraz Pomostu A w Porcie Gdynia
PublikacjaZbadano skuteczność ochrony katodowej południowego odcinka nabrzeża zachodniego oraz pomostu A w Porcie Wojennym w Gdyni. Ochrona realizowana jest za pomocą aluminiowych anod galwanicznych spawanych do ścianki szczelnej oraz pali.
-
Badania skuteczności ochrony katodowej Nabrzeża Zachodniego odcinek nr 2 (północny) oraz Pirsu C w Porcie Gdynia
PublikacjaZbadano skuteczność ochrony katodowej północnego odcinka nabrzeża zachodniego oraz pomostu C w Porcie Wojennym w Gdyni. Ochrona realizowana jest za pomocą aluminiowych anod galwanicznych spawanych do ścianki szczelnej oraz pali.
-
Badania skuteczności ochrony katodowej Ostrogi Pilotowej w Porcie Gdynia
PublikacjaPrzedmiotem opracowania jest ocena skuteczności ochrony katodowej palościanki Ostrogi Pilotowej w Porcie Wojennym w Gdyni Oksywiu. Ochrona realizowana jest za pomocą aluminiowych anod galwanicznych spawanych do ścianki.
-
Classification of submandibular salivary stones based on ultrastructural studies
PublikacjaIntroduction: Sialolithiasis remains a clinical problem with unclear etiopathogenesis, lack of prevention methods, and only surgical treatment. Materials and methods: An ultrastructure examination of submandibular sialoliths obtained from patients with chronic sialolithiasis was conducted using a scanning electron microscope and X‐ray photoelectron spectroscopy. Results: Based on the results, we divided sialoliths into three types:...
-
Ekspertyza dot. analizy osadów z powierzchni wewnętrznej rurociągu na ssaniu pompy instalacji opóźnionego koksowania
PublikacjaZakres ekspertyzy obejmuje analizę osadu na wewnętrznej stronie rurociągu prowadzącego do pompy wysokociśnieniowej 0960-P35, w tym: Analizę chemiczną osadów z powierzchni wewnętrznej rurociągu wykonanego ze stali niestopowej Określenie właściwości magnetycznych osadów Wskazanie mechanizmu tworzenia się osadów Wskazanie możliwych metod ograniczających ilość tworzących się osadów na powierzchni stali niestopowej omawianego...
-
Ekspertyza dotycząca przyczyn pęknięcia rurociągu 8”-096-P1059, zamówienie nr WU/0402/2020/MS
PublikacjaWykonano badania nieniszczące i niszczących próbek materiału rurociągu wraz z przygotowaniem próbek do badań z materiału rodzimego.
-
Ekspertyza z oceną przyczyn powstania korozji oraz oceną ryzyka obniżenia trwałości kabli sprężenia zewnętrznego konstrukcji nośnej mostu M-4 w ciągu drogi krajowej nr 90 przez rzekę Wisłę koło Kwidzyna
PublikacjaCelem pracy jest uzyskanie informacji pomocnych do podjęcia właściwej decyzji z punktu widzenia Zarządcy obiektu, co do określenia zakresu niezbędnych działań naprawczych na moście M-4 w ciągu drogi krajowej nr 90 przez rzekę Wisłę koło Kwidzyna, spowodowanych wystąpieniem korozji splotów kabli sprężenia zewnętrznego zlokalizowanego wewnątrz dźwigara skrzynkowego ustroju nośnego przedmiotowego mostu.
-
Evaluation of Temperature Influence on Electrochemical Processes Occurring in a Lithium-Ion Supercapacitor with the Use of Dynamic Electrochemical Impedance Spectroscopy
PublikacjaIn order to obtain the full impedance characteristics of a lithium-ion capacitor as a function of temperature, the authors proposed the use of dynamic electrochemical impedance spectroscopy. Impedance tests were carried out under wide range of dynamic temperature changes for lithium-ion supercapacitors. Significant differences in electrochemical processes were observed as a result of working temperature. Moreover, the quality of...
-
Investigation of the 0.4C-35Cr-45Ni-Nb Alloy after Service in High-Temperature Steam and Hydrocarbons Environment
PublikacjaThe paper presents the results of investigation of the 0.4C-35Cr-45Ni-Nb alloy, which operated in the cracked hydrocarbon feeds and dilution steam at 1125 C. The material originated from the pyrolytic furnace coil tubes, of which internal walls were in contact with the aforementioned medium, whereas the external walls were in contact with the flue gases. The examination included metallographic and mechanical tests on the material...
-
Novel fast non-linear electrochemical impedance method for corrosion investigations
PublikacjaThe paper presents a novel approach to corrosion rate monitoring using non-linear electrochemical impedance spectroscopy. The authors propose a new variant of non-linear impedance measurement using amplitude-modulated multi-frequency ac perturbation signal. It allows shortening of measurement duration so it is possible to monitor corrosion rate of the systems experiencing rapid changes. In this way a limitation resulting from lack...
-
Optimization of the Relative Humidity of Reactant Gases in Hydrogen Fuel Cells Using Dynamic Impedance Measurements
PublikacjaWater management is a key factor affecting the efficiency of proton exchange membrane fuel cells (PEMFCs). The currently used monitoring methods of PEMFCs provide limited information about which processes or components that humidity has a significant impact upon. Herein, we propose the use of a novel approach of impedance measurements using a multi-sinusoidal perturbation signal, which enables impedance measurements under dynamic...
-
Polynomial description of dynamic impedance spectrogram—introduction to a new impedance analysis method
PublikacjaThis paper presents a polynomial description of spectrograms obtained using Dynamic Electrochemical Impedance Spectroscopy. A method to fit the polynomial degree correctly is discussed. A simple electrical system of a diode connected in parallel with a capacitor was used for testing. Dynamic impedance measurements during potentiodynamic polarization were conducted. This paper presents an alternative analysis method that allows...
-
The Effect of Increasing the Amount of Indium Alloying Material on the Efficiency of Sacrificial Aluminium Anodes
PublikacjaAl-Zn-In alloys having 4.2% zinc content and various indium content in the range of 0.02–0.2% were tested with respect to the most important electrochemical properties of sacrificial anodes in a cathodic protection, i.e., the current capacity and potential of the operating anode. The distribution of In and Zn in the tested alloys was mapped by means of the EDX technique, which demonstrated that these elements dissolve well in the...
-
Ultrasonic-assisted Electrodeposition of Cu-Sn-TiO2 Nanocomposite Coatings with Enhanced Antibacterial Activity
PublikacjaCopper-based coatings are known for their high antibacterial activity. In this study, nanocomposite Cu–Sn–TiO2 coatings were obtained by electrodeposition from an oxalic acid bath additionally containing 4 g/dm3 TiO2 with mechanical and ultrasonic agitation. Ultrasound treatment was performed at 26 kHz frequency and 32 W/dm3 power. The influence of agitation mode and the current load on the inclusion and distribution of the TiO2...
Rok 2020
-
An integral-differential method for impedance determination of the hydrogen oxidation process in the presence of carbon monoxide in the proton exchange membrane fuel cell
PublikacjaThe impedance of a proton exchange membrane fuel cell powered by hydrogen contaminated with carbon monoxide, ranging from 150 to 300 ppb, is measured and discussed. The tested range of CO concentration complied with the fuel standard specified in the ISO standards. Studies of influence of CO contamination on operation of PEMFC are crucial for further development and commercialization of fuel cells for automotive applications. Based...
-
Classification of submandibular salivary stones based on ultrastructural studies
PublikacjaIntroduction: Sialolithiasis remains a clinical problem with unclear etiopathogenesis, lack of prevention methods, and only surgical treatment. Materials and methods: An ultrastructure examination of submandibular sialoliths obtained from patients with chronic sialolithiasis was conducted using a scanning electron microscope and X-ray photoelectron...
-
Corrosion hazards and inhibitor protection in the seawater injection system on the Baltic sea rig
PublikacjaOil extraction efficiency in LOTOS Petrobaltic Company is increased by means of injection of seawater into an oilfield aquifer, which is implemented on the Baltic Beta rig, operating on the Baltic Sea. Operational experience has shown a significant degree of corrosion aggressiveness in the injected water, which necessitates frequent repairs of the seawater injection installation. Evaluation of the corrosion phenomena is crucial...
-
Differential analysis of dynamic immittance spectra
PublikacjaThis work presents a new approach to the analysis of immittance spectrograms of systems characterised by non-stationarity. The possibility of linking the evolution of the immittance response with changes in the parameters describing the system is achieved by introducing a spectrum in differential form. By using the above procedure, it becomes possible to separate elements with a dependence (or lack thereof) from an independent...
-
High-Temperature Oxidation of Heavy Boron-Doped Diamond Electrodes: Microstructural and Electrochemical Performance Modification
PublikacjaIn this work, we reveal in detail the effects of high-temperature treatment in air at 600 °C on the microstructure as well as the physico-chemical and electrochemical properties of boron-doped diamond (BDD) electrodes. The thermal treatment of freshly grown BDD electrodes was applied, resulting in permanent structural modifications of surface depending on the exposure time. High temperature affects material corrosion, inducing...
-
Intergranular Corrosion Detection Using Electromagnetic Transducers for Ultrasonic Testing
PublikacjaThe aim of this paper is to create a research methodology that allows a quick analysis of the structural state of high alloy austenitic steels using non-destructive ultrasonic tests, in contrast to destructive standard methods. Electromagnetic acoustic transducers (EMAT) are used to generate and receive the ultrasonic wave and detect the microstructural changes caused by sample sensitization in elevated temperature, even after...
-
Laser induced formation of copper species over TiO2 nanotubes towards enhanced water splitting performance
PublikacjaWe proposed fast and scalable route where the ordered TiO2 nanotubes coated with thin copper layers were annealed by the laser beam of 355 nm wavelength at different fluencies in the range of 15–120 mJ/cm2. As a result, copper species are integrated with the titania substrate and the formed material exhibits unique optical absorption bands in the visible range. Moreover, X-ray photoelectron spectroscopy analysis reveals the formation...
-
Modernized cathodic protection system for legs of the production rig – Evaluation during ten years of service
PublikacjaThe modernization of cathodic protection system of the Baltic Beta platform legs is described. It was that the sacrificial anodes cone-shaped groups were to be placed on the seabed at a depth of 80 m. The measurements results of cathodic protection effectiveness during its ten-years operation are presented. The effectiveness was assessed based on the potential value along the entire length of the legs from the sea surface to the...
-
Ni/cerium Molybdenum Oxide Hydrate Microflakes Composite Coatings Electrodeposited from Choline Chloride: Ethylene Glycol Deep Eutectic Solvent
PublikacjaCerium molybdenum oxide hydrate microflakes are codeposited with nickel from a deep eutectic solvent-based bath. During seven days of exposure in 0.05 M NaCl solution, the corrosion resistance of composite coating (Ni/CeMoOxide) is slightly reduced, due to the existence of some microcracks caused by large microflakes. Multielemental analysis of the solution, in which coatings are exposed and the qualitative changes in the surface...
-
Novel application of dynamic electrochemical impedance monitoring to a cataphoretic coating process
PublikacjaThe paper presents a novel method of on-line impedance monitoring of cataphoretic coating application process. Utilization of dynamic electrochemical impedance spectroscopy (DEIS) overcame the fundamental problem connected with non-stationarity of the aforementioned coating deposition process, which eliminates classical impedance spectroscopy technique from a real-time description of cataphoresis. The paper illustrates selected examples...
-
Ocena zagrożenia korozyjnego zbiorników na terenie modernizowanego Terminala Paliw LOTOS w Piotrkowie Trybunalskim.
PublikacjaZbadano zagrożenie korozyjne nowo budowanych zbiorników na terenie modernizowanego terminala paliw. Oceny dokonano na podstawie badań agresywności korozyjnej pobranych próbek gruntu oraz wykonanych pomiarów terenowych. Uzyskane wyniki będą wykorzystane przy projektowaniu systemu ochrony katodowej nowych zbiorników podziemnych.
-
Performance of organic coatings upon cyclic mechanical load
PublikacjaA number of engineering structures fail due to the fatigue damage resulting from cyclic mechanical stress. However, as far as organic coatings are concerned this degradation factor remains underestimated. In the paper the authors propose a methodology combining global electrochemical impedance spectroscopy and local atomic force microscopy measurements for evaluation of coating resistance to an impact of repetitive mechanical stress. Typical...
-
Podstawowe procedury pomiarowe w ochronie katodowej
PublikacjaOpracowanie zawiera opis podstawowych procedur pomiarowych stosowanych przez personel ochrony katodowej w sektorze lądowych konstrukcji metalowych. Znajomość opisanych metod jest wymagana od personelu na poziomie 1 oraz na poziomie 2 kompetencji zgodnie z wymogami normy PN-EN ISO 15257:2017-10: "Ochrona katodowa -- Poziomy kompetencji osób zajmujących się ochroną katodową -- Podstawa systemu certyfikacji". Opracowanie przeznaczone...
-
Pomiary terenowe i analiza techniczna stopnia agresywności korozyjnej gruntu w Bazie PERN S.A. Adamowo.
PublikacjaW ramach realizacji pracy pobrano próbki gruntu na terenie bazy paliw i wykonano na nich analizy fizyko-chemiczne, na podstawie których określono agresywność korozyjną gruntu na terenie bazy. Uzyskane wyniki będą wykorzystane przy projektowaniu zabezpieczeń przeciwkorozyjnych obiektów na terenie bazy paliw.
-
Pomiary terenowe i analiza techniczna stopnia agresywności korozyjnej gruntu w Bazie PERN S.A. Gdańsk
PublikacjaW ramach realizacji pracy pobrano próbki gruntu na terenie bazy paliw i wykonano na nich analizy fizyko-chemiczne, na podstawie których określono agresywność korozyjną gruntu na terenie bazy. Uzyskane wyniki będą wykorzystane przy projektowaniu zabezpieczeń przeciwkorozyjnych obiektów na terenie bazy paliw.
-
Pomiary terenowe i analiza techniczna stopnia agresywności korozyjnej gruntu w Bazie PERN S.A. Miszewko Strzałkowskie
PublikacjaW ramach realizacji pracy pobrano próbki gruntu na terenie bazy paliw i wykonano na nich analizy fizyko-chemiczne, na podstawie których określono agresywność korozyjną gruntu na terenie bazy. Uzyskane wyniki będą wykorzystane przy projektowaniu zabezpieczeń przeciwkorozyjnych obiektów na terenie bazy paliw.
-
Stratification of nano-pigments in anti-corrosive coatings by means of magnetic field
PublikacjaThe concept of self-stratification of coatings, although attractive, causes difficulties in its practical use, especially when pigments are added to the resins. An alternative way of obtaining a multilayer structure in a single step was presented. Using the inhomogeneous magnetic field and magnetically active components of the coating, the possibility of vertically graded differentiation of the one layer properties has been verified....
-
The impact of air humidity on the operation of proton exchange membrane fuel cells determined using dynamic electrochemical impedance spectroscopy
PublikacjaThis paper describes the changes in the fuel cell impedance across a range of current loads and humidity changes. The changes of each equivalent circuit parameters representing specific processes occurring in fuel cells, as a function of humidity and current changes, were determined. Within the combined scope of current and humidity, the optimal working conditions of the cells were determined, corresponding to the lowest impedance...
-
The impedance of hydrogen oxidation reaction in a proton exchange membrane fuel cell in the presence of carbon monoxide in hydrogen stream
PublikacjaEvaluation of performance of a proton exchange membrane fuel cell, which is affected by carbon monoxide that pollutes the hydrogen stream, was presented. This influence was studied for carbon monoxide concentration of 125–325 ppb, which are close to values specified in ISO 14687:2019 standard. Performed studies provided crucial information for further development of fuel cell as an energy source for automotive application. Impedance...
-
The influence of the Cu2O deposition method on the structure, morphology and photoresponse of the ordered TiO2NTs/Cu2O heterojunction
PublikacjaThe increased interest in highly ordered titania structures exhibiting tubular shape that could be directly formed onto the stable substrate is related with the intensive research on their modification enabling absorption of light within the wide solar spectrum and its further conversion into electric or chemical energy. Among others, formation of uniform 3D heterojunctions based on the TiO2 nanotubes attracts attention since porous...
-
Ultrastructural analysis of the submandibular sialoliths: Raman spectroscopy and electron back-scatter studies
PublikacjaThe aim of work was the epidemiological analysis of the occurrence of sialolithiasis of the submandibular gland in adults and the evaluation of the ultrastructure of salivary stones. The study sample consisted of 44 sialoliths. Analysis of the structure and chemical composition of sialoliths was performed using a Scanning Electron Microscope and Raman Spectroscopy. Comparing our results with the literature we can say that the epidemiology...
Rok 2019
-
Condition of Reinforced Concrete Structures and Their Degradation Mechanism at the Former Auschwitz Concentration and Extermination Camp
PublikacjaThis paper presents the results of investigations on reinforced concrete structures present in the former Auschwitz I and Auschwitz II-Birkenau concentration and extermination camp. Field inspection employing the non-destructive method of reinforcement potential measurement according to the ASTM-C 876–15 standard, followed by laboratory investigations performed on genuine historic reinforced concrete samples collected from the...
-
Heterogeneous oxidation of highly boron-doped diamond electrodes and its influence on the surface distribution of electrochemical activity
PublikacjaThe electrochemical active surface area (EASA) of polycrystalline boron-doped diamond (BDD) electrodes is heterogeneous and can be affected by numerous factors. There is a strong need for proper consideration of BDD heterogeneity in order to improve this material's range of application in electrochemistry. Localized changes in surface termination due to the influence of oxidation agent result in increased surface resistance. The...
-
Multifrequency Nanoscale Impedance Microscopy (m-NIM): A novel approach towards detection of selective and subtle modifications on the surface of polycrystalline boron-doped diamond electrodes
PublikacjaIn this paper, we describe the modification of Nanoscale Impedance Microscopy (NIM), namely, a combination of contact-mode atomic force microscopy with local impedance measurements. The postulated approach is based on the application of multifrequency voltage perturbation instead of standard frequency-by-frequency analysis, which among others offers more time-efficient and accurate determination of the resultant impedance spectra...
-
New Method of Non-Linear Electrochemical Impedance Spectroscopy with an Amplitude-Modulated Perturbation Signal
PublikacjaThe paper presents a new method of non-linear electrochemical impedance spectroscopy (NLEIS), which allows fast and nondestructive evaluation of the corrosion rate and determination of the Tafel coefficients values for a corrosion system under investigation. This method employs amplitude modulation of the ac perturbation signal. The study demonstrated that it was possible to obtain impedance characteristic as a function of the...
-
The influence of dynamic load changes on temporary impedance in hydrogen fuel cells, selection and validation of the electrical equivalent circuit
PublikacjaTo achieve optimal performance of a fuel cell, a reliable monitoring and diagnostic method is required. The currently utilized methods give limited information or they are impossible to use under dynamic working conditions. To obtain comprehensive information about the fuel cell operation we utilized novel dynamic electrochemical impedance spectroscopy. Impedance measurements in dynamic mode were performed on a hydrogen fuel cell,...
Rok 2018
-
Application of Electrochemical Impedance Spectroscopy to evaluate cathodically protected coated steel in seawater
PublikacjaTwo types of organic coated carbon steel (S235JR2 grade) electrodes were exposed to artificial seawater environment. One prepared type was defect free while the other one had an intentionally introduced φ0,5 cm coating defect. Both kinds of samples were polarized during the exposure to four potentials corresponding to four different cathodic protection levels. Evolution of their EIS spectra is presented in this paper. Results obtained...
-
Complex Corrosion Monitoring System for Crude Distillation Unit in Form of Neutral Network
PublikacjaComplex and successful corrosion monitoring of refinery processes can significantly reduce material losses and failure risk. The developed corrosion monitoring system is based on online ultrasonic sensors, ER (electrical resistance) probes, gravimetric method and multipoint analytical analysis of chemical composition of the fluids. Additional online LPR (linear polarization resistance) sensors controlling corrosiveness of sour...
-
Degradation of protective coatings in steel chimneys of flue gas desulfurisation system
PublikacjaThis paper presents problems associated with corrosion of steel stacks and changes in philosophy of corrosion protection when implemented into flue gas desulphurization systems. In-situ tests were taken by means of electrochemical impedance spectroscopy at the stack which discharges flue gas before wet lime/limestone desulphurization. A very quick electrolyte absorption by the spherical infill vinylester coating was found using...
-
Development of dynamic method for evaluation of inhibition efficiency on the example of 8-hydroxyquinolin
PublikacjaSelection of a proper inhibitor should be based on the evaluation of its mechanism and effective concentrations. Mechanism of inhibition usually has dynamic character due to changing physicochemical conditions of the environment and corroding metal surface. Most of actually used methods are stationary or contain assumptions which highly influences obtained values. Development of new dynamic method, based on modified EIS, allows...
-
Impedance evaluation of coatings from biobased material
PublikacjaThe authors propose a modification of sodium caseinate edible coating for foodstuff protection. The aim was to improve the film’s barrier properties. It was achieved by the addition of propolis, which is a natural, environmentally friendly product known from its intrinsic sealing action. In the next step, propolis-admixed sodium caseinate films were exposed to elevated temperature for 10 min. This approach was meant to improve...
-
Implementation of DEIS for reliable fault monitoring and detection in PEMFC single cells and stacks
PublikacjaDynamic Electrochemical Impedance Spectroscopy (DEIS) was presented as novel method for diagnostic and monitoring of PEMFC stack and single cells operation. Impedance characteristics were obtained simultaneously with current - voltage characteristics for stack and each individual cell. Impedance measurements were performed in galvanodynamic mode. It allowed to compare performance of each cell and identification of faulty cell operation...
-
Local electrochemical impedance spectroscopy in dynamic mode of galvanic coupling
PublikacjaA novel method that combines local electrochemical impedance spectroscopy and mapping in dynamicmode is proposed. Method was validated over two galvanic couplings, namely zinc/copper and cad-mium/copper. Impedance spectrum response for all measuring points was obtained by means ofsimultaneous implementation of selected range of frequencies. Proposed method allows the measure-ment in a more time-efficient manner, at the same time...
-
Metal dusting phenomena of 501 AISI furnace tubes in refinery fractional distillation unit
PublikacjaThe purpose of this investigation was to conduct the failure analysis of 501 AISI furnace tubes places before distillation column in fractional distillation unit. The investigated furnace tubes were planned to work for ten years however after just two years of exploitation <30% of the material left. The observed corrosion process had the intense and complex character. The well-adhered shiny black deposits and deep, round pits were...
-
Ocena przyczyn zniszczenia powłoki ChemLine na zbiorniku 1300T2
PublikacjaWykonano ekspertyzę związaną z oceną zniszczeń powłoki siloxiranowej na łożonej na powierzchnie wewnętrzne zbiornika magazynowego chlorku metylenu i chlorku etylenu.
-
Water uptake in protective organic coatings and its reflection in measured coating impedance
PublikacjaWater uptake in commercially available epoxy coating on mild steel using impedance spectroscopy and gravimetry was studied. The water content in the coating was determined using the Brasher-Kingsbury equation and various methods of coating capacitance calculation used in the literature. The obtained results were compared with reference gravimetric data. An overestimation of values obtained from impedance data in relation to gravimetric...
Rok 2017
-
Analiza składu chemicznego produktów korozji wraz z określeniem przyczyn ich powstania
PublikacjaCelem wykonanych prac jest analiza składu chemicznego osadów korozyjnych, występujących na dostarczonych układach scalonych, wraz z określeniem potencjalnych przyczyn ich powstania.
-
Assessment of copper surface coverage with corrosion inhibitor using AFM-based local electrical measurements
PublikacjaThe paper presents a new method of assessment of metal surface coverage with corrosion inhibitor and thus of inhibitor protective performance. It is based on the atomic force microscopy measurement performed in a contact mode. Apart from topography images the proposed approach allows acquisition of local DC maps and local electrical impedance spectra via application of DC bias voltage or AC perturbation signal between the conductive...
-
Badania korozyjne zbiornika magazynowego kwasu chlorooctowego
PublikacjaWykonano ekspertyzę zbiornika magazynowego na kwas chlorooctowy. Stwierdzono, że zbiornik znajduje się w stanie pasywnym (autopasywacja zachodzi w wyniku obecności powietrza po otwarciu zbiornika). Występuje korozja ogólna zbiornika w wyniku bardzo wysokiej agresywności korozyjnej środowiska (kwasu). Procesy korozyjne występują w trakcie napełnienia zbiornika kwasem.
-
Badania skuteczności ochrony katodowej nóg platformy wydobywczej
PublikacjaWykonano badania potencjałowe parametrów ochrony platformy wydobywczej Baltic Beta. Stwierdzono występowanie pełnej ochrony katodowej w rejonie dna. Stan techniczny anod wykazuje znaczne zużycie, jednakże w dalszym ciągu realizują proces ochorny
-
Badanie składu chemicznego wraz z obrazowaniem powierzchni próbek przy użyciu SEM/EDX
PublikacjaWyniki analizy degradacji pieca pracującego w warunkach próżniowych, w zakresie powyżej 1200 st.C.
-
Chemical-Assisted Mechanical Lapping of Thin Boron-Doped Diamond Films: A Fast Route Toward High Electrochemical Performance for Sensing Devices
PublikacjaThere is an urgent need for an effective and economically viable increase in electrochemical performance of boron-doped diamond (BDD) electrodes that are used in sensing and electrocatalytic applications. Specifically, one must take into consideration the electrode heterogeneity due to nonhomogenous boron-dopant distribution and the removal of sp2 carbon impurities saturating the electrode, without interference in material integrity....
-
Corrosion process monitoring by AFM higher harmonic imaging
PublikacjaThe atomic force microscope (AFM) was invented in 1986 as an alternative to the scanning tunnelling microscope, which cannot be used in studies of non-conductive materials. Today the AFM is a powerful, versatile and fundamental tool for visualizing and studying the morphology of material surfaces. Moreover, additional information for some materials can be recovered by analysing the AFM's higher cantilever modes when the cantilever...
-
CORROSION TESTING OF SAMPLES ACCORDING TO ASTM G36
PublikacjaAt the end of the study, samples were found to have structures characteristic for intercrystalline corrosion. This indicates that the samples provided (fragments of the whole) were sensitized before starting the study in boiling MgCl2.On cross sections, fine cracks are observed on all samples tested.
-
Corrosivity of environment and the current state of the steel elements at the former Auschwitz concentration camp
PublikacjaThe objective of this study was to assess corrosivity of the atmospheric environment in the former Auschwitz I and Auschwitz II-Birkenau concentration and extermination camp, and to identify the protective properties of existing corrosion products in order to estimate the actual corrosion rate of original steel elements located there. The current atmospheric corrosivity of the former Auschwitz camp, specified during one year of exposure...
-
Determination of Local Corrosion Current from Individual Harmonic Components
PublikacjaHarmonic analysis has been used in corrosion measurements for several decades. During this period the method has been refined and developed. Nevertheless, the technique has not been applied to properties determination in local scale yet. This paper is focused on local corrosion current measurements based on harmonic analysis. For this purpose, a non-linear nature of electrode processes is used and measured in local scale applying...
-
Determination of pitting corrosion stage of stainless steel by galvanodynamic impedance spectroscopy
PublikacjaThis paper investigates the methodology for differentiation of multistep process of pitting corrosion of AISI 304 stainless steel in the environment of iron (III) chloride. Measurements were performed using Galvanodynamic Electrochemical Impedance Spectroscopy (GDEIS). Application of this methodology allowed monitoring of natural corrosion process without external current (IDC = 0A) nor potential perturbation of the system. Applied...
-
Diamond-Phase (Sp3-C) Rich Boron-Doped Carbon Nanowalls (Sp2-C): A Physico-Chemical And Electrochemical Properties
PublikacjaThe growth of B-CNW with different boron doping levels controlled by the [B]/[C] ratio in plasma, and the influence of boron on the obtained material’s structure, surface morphology, electrical properties and electrochemical parameters, such as -ΔE and k°, were investigated. The fabricated boron-doped carbon nanowalls exhibit activity towards ferricyanide redox couple, reaching the peak separation value of only 85 mV. The flatband...
-
Electrochemically Induced Synthesis of Triphenylamine-based Polyhydrazones
PublikacjaTriphenylamine-based hydrazones were subjected to electropolymerization process that gave well conductive hydrazone based polymers. The first example of polyhydrazone formation during the electrochemical process was shown. The estimation of polymer structure was demonstrated using IR spectroelectrochemistry. The EPR spectroelectrochemistry allowed to explain why in some cases dimer couldn’t be formed. The results of electrochemical,...
-
Evaluation of organic coating systems for corrosion protection of industrial equipment using impedance spectroscopy
PublikacjaThe high economic impact of corrosion can be reduced by enhanced corrosion management and prevention based on appropriate means. This applies in particular to the protection of structures with organic protective coatings. Steel is subject to corrosion that reduces its service life and leads to destruction in most severe cases. The application of paints to metallic objects for corrosion control has been known for a long time and...
-
Examination of the epoxy coating system's resistance to Corrobill
PublikacjaThe tests of the influence of the surface cleaning agent on the epoxy coating were carried out. Electrochemical and corrosion tests were carried out. The effect of the preparation on the adhesion and hardness of the tested coating was tested.
-
Fabrication and Significant Photoelectrochemical Activity of Titania Nanotubes Modified with Thin Indium Tin Oxide Film
PublikacjaOrdered titanium dioxide nanotubes (TiO2NTs) modified with indium tin oxide (ITO) films were obtained via magnetron sputtering, in which ITO plate was used as a target, onto the as-anodized titania support followed by the calcination process. The morphology of fabricated material with deposited oxide was investigated using scanning electron microscopy. Raman and UV–Vis spectroscopies were utilized to characterize crystalline phase...
-
Heterogeneous distribution of surface electrochemical activity in polycrystalline highly boron-doped diamond electrodes under deep anodic polarization
PublikacjaThe surface homogeneity of boron-doped diamond electrodes is variable and depends on anodic polarization conditions. The differentiation factor is the gradual and localized change in surface termination. A series of measurements under different polarization conditions was performed in order to investigate the scale of this effect. Nanoscale impedance microscopy (NIM) revealed large variation of surface resistance in individual...
-
Impedance Measurement and Selection of Electrochemical Equivalent Circuit of a Working PEM Fuel Cell Cathode
PublikacjaThe dynamic impedance analysis of direct methanolfuel cell (DMFC) cathode supplied with pure oxygen is pre-sented. Presented results were obtained during dynamic chang-es of the current density in working fuel cell. Investigation ofthe occurring processes at cathode was carried with dynamicelectrochemical impedance spectroscopy (DEIS). A discussionwas conducted based on the determined correlation parameterχ2. It was shown that...
-
Impedance monitoring of corrosion degradation of plasma electrolytic oxidation coatings (PEO) on magnesium alloy
PublikacjaImpedance technique based on continuous multisinusoidal current perturbation was used to explain degradation process of plasma electrolytic oxidation coatings (PEO) on magnesium alloy. An obtained impedance spectrum was fitted by electrical equivalent circuit to describe properties of conversion layer on magnesium alloy. Additionally, galvanostatic mode maintained during experiment, with DC current equal to zero, allowed to achieve...
-
Monitorowanie szybkości korozji oraz dobór materiałów konstrukcyjnych w instalacji wody morskiej platformy Baltic Beta
PublikacjaWykonano analizę szybkości korozji systemu monitorowania korozji z okresu od 25.11.2016 do 12.07.2017. Zdemontowano czujnik korozyjny w instalacji wody morskiej, Zainstalowani nowy czujnik z opcją pomiaru szybkości korozji metodą kuponową. Monitoringiem poddano następujące materiały: 1.7362, 1.5415, 1.0038
-
Porównanie właściwości barierowych i mechanicznych dwóch systemów poliuretanowych na stali węglowej S235JR eksponowanych w warunkach symulujących narażenia występujące w glebie
PublikacjaPorównano właściwości barierowe i mechaniczne próbek powłok na stali dostarczonych przez Zleceniodawcę eksponowanych w trzech środowiskach symulujących narażenia występujące w glebie.Do oceny degradacji w tych środowiskach po 2,5 miesięcznej ekspozycji wykorzystano spektroskopię impedancyjną oraz testy normowe. Wskazano powłokę o korzystniejszych właściwościach ochronnych w warunkach glebowych.
-
Time evolution of Electrochemical Impedance spectra of cathodically protected steel in artificial seawater
PublikacjaUsability of Electrochemical Impedance Spectroscopy data for better cathodic protection control was investigated. Carbon steel – S235JR2 grade specimen were exposed in artificial seawater environment. Samples were polarized and their potentials corresponded to four different cathodic protection degrees. Time evolution of Electrochemical Impedance spectra was investigated. Goodness of fit function (X2) was analysed in terms of proper...
-
Wyjaśnienie przyczyn korozji rur kotła, wytwornicy pary technologicznej instalacji Olefiny
PublikacjaWykonano badania przyczyn korozji rurek wytwornicy pary instalacji Olefiny. Przeprowadzono badania metalograficzne oraz SEM i EDX produktów korozji
-
Wykonanie czujnika LPR oraz dobór materiałów konstrukcyjnych w instalacji wody morskiej
PublikacjaWykonano analizę pracy systemu monitorowania korozji, dokonano wymiany czujnika. Zamontowano nowy czujnik z opcją pomiaru kuponowego w celu doboru materiałów konstrukcyjnych do instalacji wody morskiej.
-
Wykonanie oceny stanu wykładziny chemoodpornej wieży Absorbcyjnej T102 Solinox
PublikacjaPrzeprowadzono szczegółowe badania wykładziny chroniącej wewnętrzną częśc absorbera SO2. Na podstawie wykonanych badań i pomiarów zaproponowano alternatywne metody poprawy jakosci wykładziny.
Rok 2016
-
Badanie składu chemicznego wraz z obrazowaniem powierzchni próbek przy użyciu SEM/EDX
PublikacjaPięć niezależnych analiz materiałów bimetalicznych i innych elementów produkcyjnych, bazujących na analizie mikrograficznej oraz składu chemicznego z oceną przyczyn zachodzenia obserwowanych procesów
-
Critical analysis of laboratory measurements and monitoring system of water-pipe network corrosion-case study.
PublikacjaCase study of corrosion failure of urban water supply system caused by environmental factors was presented. Nowadays corrosion monitoring of water distribution systems is an object of major concern. There is possibility of application broad range of techniques like gravimetric and electrochemical. Both kinds of techniques can be applied in laboratory and field conditions. In many cases researches limit the case analysis to measurements...
-
Determination of time dependence of coated metal electrical and electrochemical parameters during exposure using principal component analysis
PublikacjaThe use of the principal component analysis (PCA) permits the complex and quantitative analysis of the time dependence of electrical and electrochemical parameters of coated metal obtained by fitting impedance data. So far, changes in electrical and electrochemical parameters during exposure were analyzed independently. In this way, some of the information contained in the relationship between changes in parameters over time are...
-
Development Of Dynamic Method For Evaluation Of Corrosion Rate On The Example Of Organic Corrosion İnhibitor
PublikacjaMeasurements of the corrosion rate belong to the most important aspects of materials science. In order to reduce material loss corrosion inhibitors are used. However selection of proper inhibitor should be based on evaluation of its mechanism and effective concentrations. Mechanism of inhibition usually has dynamic character so physicochemical parameters are changing in time. Most of actually used methods...
-
Ekspertyza stanu technicznego zbiorników wysłodzin
PublikacjaCelem pracy było określenie stanu technicznego czterech zbiorników wysłodzin na terenie Browaru Elbląg. Zbiorniki oddane zostały do użytku w 1984 roku i zostały wykonane ze stali niestopowej konstrukcyjnej. Ekspertyza została wykonana na podstawie badań ultradźwiękowych grubości stali zbiornika, głębokości wżerów, magnetycznym pomiarze grubości powłoki malarskiej, pomiarze potencjałów stali względem elektrody siarczano-cynkowej...
-
Electrolytic corrosion of water pipeline system in the remote distance from stray currents– case study
PublikacjaCase study of corrosion failure of urban water supply system caused by the harmful effects of stray currents was presented. The failure occurred at a site distant from the sources of these currents namely the tramway and railway traction systems. Diagnosis revealed the stray currents flow to pipeline over a remote distance of 800 ÷ 1,000 meters from the point of failure. At the point of failure stray currents flowed from the pipeline...
-
Ellipsometric investigation of nitrogen doped diamond thin films grown in microwave CH4/H2/N2 plasma enhanced chemical vapor deposition
PublikacjaThe influence of N2 concentration (1%–8%) in CH4/H2/N2 plasma on structure and optical properties of nitrogen doped diamond (NDD) films was investigated. Thickness, roughness, and optical properties of the NDD films in the VIS–NIR range were investigated on the silicon substrates using spectroscopic ellipsometry. The samples exhibited relatively high refractive index (2.6 6 0.25 at 550 nm) and extinction coefficient (0.05 6 0.02...
-
Instantaneous impedance monitoring of synergistic effect between cavitation erosion and corrosion processes
PublikacjaThe most common method of determination of cavitation erosion resistance as well as the magnitude of erosion-corrosion synergistic interaction is based on the weight loss measurements. Nondestructive characterization of installations elements is in most cases impossible to perform. Also, such a measurement does not include local types of failure or alteration of operating conditions. There is an urge to elaborate a method for monitoring...
-
Investigation of the electrochemical behaviour of AA1050 aluminium alloy in aqueous alkaline solutions using Dynamic Electrochemical Impedance Spectroscopy
PublikacjaThe paper presents the electrochemical behaviour of aluminium alloy AA1050 in aqueous alkaline media in the pH range 14–8.5. Electrochemical study was applied in order to obtain comprehensive information on the mechanism and kinetics of the process of anodic dissolution of aluminium, supplemented by monitoring of surface topography using an electron microscope. The corrosion rate of AA1050 increases with increasing concentration...
-
Metody oczyszczenia i zabezpieczenia antykorozyjnego ocynkowanych elementów balustrad i konstrukcji balkonów w budynkach mieszkalnych GTBS
PublikacjaDokonano oglądu stanu obecnego pomalowanych elementów balustrad i konstrukcji balkonów budynków mieszkalnych GTBS przy ulicach Wilanowskiej 10 i Jeleniogórskiej 9 oraz 19 w Gdańsku jako reprezentatywnych przykładów odspojeń warstw farby na powierzchni ocynkowanej. Opisano mechanizm i przyczyny wystąpienia wad. Zaproponowano metody oczyszczenia powierzchni ze starych powłok, przygotowania podłoża pod nowe wymalowania i warunki...
wyświetlono 7190 razy