ISSN:
Punkty Ministerialne: Pomoc
Rok | Punkty | Lista |
---|---|---|
Rok 2024 | 5 | Czasopisma spoza wykazu ministerialnego 2024 |
Rok | Punkty | Lista |
---|---|---|
2024 | 5 | Czasopisma spoza wykazu ministerialnego 2024 |
2023 | 5 | Czasopisma spoza wykazu ministerialnego 2023 |
2022 | 5 | Czasopisma spoza wykazu ministerialnego (2019-2022) |
2021 | 5 | Czasopisma spoza wykazu ministerialnego (2019-2022) |
2020 | 5 | Czasopisma spoza wykazu ministerialnego (2019-2022) |
2019 | 5 | Czasopisma spoza wykazu ministerialnego (2019-2022) |
2018 | 10 | B |
2017 | 10 | B |
2016 | 5 | zagraniczne czasopismo naukowe |
2015 | 5 | zagraniczne czasopismo naukowe |
2014 | 10 | B |
2013 | 10 | B |
2012 | 10 | B |
2011 | 10 | B |
2010 | 20 | A |
Punkty CiteScore:
Rok | Punkty |
---|---|
Rok 2022 | 0 |
Rok | Punkty |
---|---|
2022 | 0 |
2020 | 1.1 |
2019 | 0.8 |
2018 | 0.6 |
2017 | 0.7 |
2016 | 0.8 |
2015 | 0.7 |
2014 | 0.8 |
2013 | 0.6 |
2012 | 0.6 |
2011 | 0.7 |
Impact Factor:
Sherpa Romeo:
Prace opublikowane w tym czasopiśmie
Filtry
wszystkich: 86
Katalog Czasopism
-
Limb/Ground Impacts and Unexpected Impacts Control Strategy for a Model of a Limb of a Walking Robot
PublikacjaPraca prezentuje wyniki analizy numerycznej dynamiki robota kroczącego. Uwaga skoncentrowana jest na zagadnieniu kontaktu odnóża z podłożem. W kierunku normalnym kontakt opisano więzami jednostronnymi. W kierunku stycznym, założono obecność poślizgu i tarcia. Z uwagi na jednostronność kontaktu, może się on rozpocząć z niezerową prędkością względną. Z chwila rozpoczęcia kontaktu, prędkości zmieniają się gwałtownie. Towarzysza temu...
-
Rigid Finite Element Modeling for Identification of Vibrations in Elastic in Elastic Rod Driven by a DC-motor Suplied from a Thyristor Rectifier
PublikacjaRozdział dotyczy analizy numerycznej układu elektromechanicznego. Układ składa się z silnika zasilanego z jednopołówkowego prostownika tysystorowego i napędzanego tym silnikiem wirującego pręta. Celem obliczeń jest określenie postaci i wielkości drgań pręta, jeśli uwzględniamy jego elastyczność. Dyskretna struktura modelu to łańcuch wielomasowy ciał - sztywnych ciał połączonych bezmasowymi węzłami. Autorzy obliczyli zachowanie...
-
The automation of test stand for engine cooling system testing
PublikacjaW rozdziale przedstawiono budowę stanowiska do badań układu chłodzenia silnika samochodowego typu M111920. Układ był wyposażony w obwód podgrzewania paliwa gazowego i układ akumulacji ciepła. Stanowisko wyposażono w liczne termopary do pomiaru temperatur płynów i części metalowych silnika. Ważnym opracowanym zagadnieniem było rejestrowanie wielu pomiarów w czasie rzeczywistym, do czego użyto sieci transmisji danych CAN.
-
Mechatronic system for automatic inspection of circular saw teeth
PublikacjaArtykuł prezentuje system mechatroniczny do automatycznej oceny geometrii ostrzy pił tarczowych. Opisywany system wizyjny został zastosowany w automatycznym kontrolerze ostrzy pił tarczowych WKOPTar. Wrzeciono urządzenia posiada swój napęd sterowany bezstopniowo obrazem ostrzy i zapewnia powtarzalne pozycjonowanie ostrzy w celu przechwycenia ich obrazów, które są następnie analizowane z wykorzystaniem specjalnego oprogramowania....
-
Multicomponent layers for aluminium alloys surface consolidation
PublikacjaThe main reason of the surface modification of the components such as pistons and cylinder blocks made of cast aluminium alloys is to obtain high hardness, wear and corrosion resistance of the working surface for larger lifetime of the motor-car and aircraft engines. In that aspect, the new conception of development - by hybrid method - of surface layers containing manganese, nitrogen, sulphur (Mn-N-S) and manganese, nitrogen,...
-
Determination of ability of hydrotronic systems to start in low ambient temperatures
PublikacjaPrzedstawiono wyniki badań symulacji komputerowej zespołów układów hydrotronicznych w warunkach szoku termicznego. Pokazano metodę określania zdatności hydrotronicznych zespołów i układów podczas rozruchu w warunkach szoku termicznego.
-
High temperature corrosion of evaporator tubes with thermal sprayed coatings
PublikacjaDegradation examinations of outer surface of low-emission steam boiler evaporator tubes are presented in the paper. Metallographic evaluation of scale morphology, its micro sites chemical composition analysis and distribution of elements on cross sections have been performed. Water-wall tubes were exposed in steam boiler for up to two years period. Common tubes made of 16Mo3 steel suffered sulphide and molten salts corrosions....
-
Monitoring of Velocity of Manufacturing Machines Subassamblieas by Means of a DAQ System
PublikacjaArtykuł dotyczy dokładnych cyfrowych pomiarów prędkości ruchu podzespołów maszyn, realizowanych za pomocą enkoderów kwadraturowych, kart licznikowych DAQ oraz dedykowanych aplikacji pomiarowych DAQ. Przedstawiono koncepcje trzech różnych sposobów takiego pomiaru. W pierwszym sposobie, nazywanym ''częstotliwościowym'', pomiar odbywa się poprzez bramkowane zliczanie impulsów enkodera. Drugi sposób nazywany ''czasowym'' polega na...
-
Properties of surface layers of duplex stainless steel after burnishing processes
PublikacjaStress corrosion cracking resistance of cold worked layers of 25 Cr duplex stainless steel grade UR52N+ has been investigated. The surface layers were performed through burnishing treatment. The residual stresses at surface layers were determined using grazing angle incidence X-ray diffraction method (g-sin2 Ψ). Corrosion tests were performed with the use of Slow Strain Rate Test technique in boiling 35% MgCl2 solution. It has...
-
Finishing of Ceramics in a Single-Disk Lapping Machine Configuration
PublikacjaPrzedstawiono metodę obróbki ceramiki technicznej na zmodifikowanej docierarce jednotarczowej z niezależnym napędem pierścienia prowadzącego. Omówiono przebieg obróbki z wykorzystaniem nowych narzędzi i zastosowaniem ziarna wiązanego.
-
Cavitation wearing of the SUPERSTON alloy after laser treatment at cryogenic conditions
PublikacjaThe purpose of this paper is to demonstrate the method of laser remelting at cryogenic conditions of the SUPERSTON alloy and its influence on microstructure and cavitation wearing. The cavitation test was performed using the rotating disc facility in IPM PAN Gdansk. During the cavitation test, the mass loss of the material with different parameters of laser remelting was determined. Surface and cross-section microstructure of the...
-
Research of hydrotronic variable displacement radial piston pump with electro -pneumatic control
PublikacjaThe paper presents the developed new electro-pneumatic control (pneumotronic) system for hydraulic fixed-displacement radial piston pump. Hydraulic fixed-displacement radial piston pump equipped with the proposed control system changes into hydrotronic variable-displacement radial piston pump. Pump flow rate control is realized by means of programmable logic controller, electro-pneumatic valves, pneumatic cylinders and a sensor.
-
Port-Based Modelling of Distributed-Lumped Parameter Systems
PublikacjaThere in the paper is presented an uniform, port-based approach to modelling of both lumped and distributed parameter systems. Port-based model of the distributed system has been defined by application of bond graph methodology and distributed transfer function method (DTFM). The approach proposed combines versatility of port-based modelling and accuracy of distributed transfer function method. The concise representation of lumped-distributed...
-
Effect of the Unit Pressure on the Selection Parameters of Intermetallic Coastings NiAl and Ni3Al after Platic Working
PublikacjaW artykule omówiono wpływ zgniotu na wybrane parametry warstwy międzymetalicznej NiAl i Ni3Al napawanej na stali C45 podanej obróbce plastycznej poprzez prasowanie na zimno.
-
Modal Reduction and Analysis of Gyroscopic Systems
PublikacjaThe paper introduces the method of the modal reduction of systems that experience the Coriolis acceleration or gyroscopic effect component. In such cases corresponding system equations are non-self-adjoined. To solve the problem modal reduced model is built up for the system without Coriolis acceleration or gyroscopic effect terms. These phenomena are included by application of any lumping technique. Hence, the final reduced model...
-
Analysis of Asymmetrical Rolling Process of Multilayer Plates
PublikacjaW niniejszej pracy przedstawiono wyniki badań numerycznych asymetrycznego procesu walcowania blach wielowarstwowych M1E-Al99,8-AlMg5. Modelowanie numeryczne procesu walcowania blach wielowarstwowych przeprowadzono w programie Forge 2D, którego obliczenia bazują na metodzie elementów skończonych. Przedstawione w pracy wyniki umożliwiły przeprowadzenie analizy procesu walcowania blach wielowarstwowych.
-
Surface Roughness Model Components Created by Stereolithography Method
PublikacjaW pracy przedstawiono charakterystykę powierzchni elementów wykonywanych metodą stereolitografii. Opisano modele chropowatosci stosowane do opisywania powierzcni wraz z prezentacją formuł matematycznych. W oparciu o wyniki badań eksperymentalnych przeprowadzono częściową weryfikację modeli.
-
Modeling and simulation of tool cycle in manufacturing cell
PublikacjaThe paper addresses issues concerning modeling and analysis of tool flow within a three-machine manufacturing cell used for small batch manufacturing of a definite spectrum of prismatic parts. The approach utilizes a method for job and tool allocation to work centers with limited number of machines and capacity of tool resources, based on the analysis of formalized relations: job - tool sets required. Selected tool flow control...
-
Optimum Control of Gyroscopic Systems
PublikacjaThe problem of optimum control of transverse rotor vibrations with gyroscopic interactions has been described and solved in the paper. An integral performance index has been defined for such system in order to minimize vibration level of a chosen rotor point. For this reason, an efficient way of finding the weight coefficients of integral performance index for multi-degrees-of-freedom system with gyroscopic interactions has been...
-
The effect of the ceramic dispersion on the nickel matrix composite coating properties after plastic working
PublikacjaW pracy określono wpływ fazy dyspersyjnej Al2O3 na wybrane potencjalne właściwości powłok kompozytowych o osnowie niklowej. Powłoki Ni-Al-Al2O3 zostały nałożone na próbki stalowe przy użyciu technologii poddźwiękowego płomieniowego natryskiwania cieplnego. Następnie poddane zostały obróbce plastycznej na zimno i na gorąco poprzez walcowanie, a także prasowania na zimno na prasie hydraulicznej. Obróbka plastyczna jest metodą alternatywną...
-
Multibody and electromechanical modelling in dynamic balancing of mechanisms for mechanical and electromechanical systems
PublikacjaPraca prezentuje zagadnienia wspólnego modelowania układu wieloczłonowego i napędu elektrycznego oraz problemy wyrównoważania mechanizmów. Analizowanym układem mechanicznym jest płaski czworobok przegubowy. Analizowany mechanizm zamodelowano jako układ wieloczłonowy z zamkniętymi wielobokami ciał. Do wymuszenia ruchu układu wykorzystano model silnika prądu stałego. Zbadano oddziaływania pomiędzy płytą mocującą czworoboku i otoczeniem....
-
Identification of the Inertia of Masses Flowing Water through the Pipes in Water Power Plants
PublikacjaW artykule przedstawiono sposób identyfikacji stałej czasowej reprezentującej bezwładność mas przepływającej wody w systemie rurociągów, w elektrowni wodnej. Przedstawiono strukturę modelu układu regulacji prędkości kątowej wykorzystywanego w procesie identyfikacji oraz przeprowadzono badania skuteczności działania metody w środowisku Matlab-Simulink. Opisano najistotniejsze wnioski wynikające z przeprowadzonych badań symulacyjnych.
-
Selected problems of navigation of educational mobile robot
PublikacjaW artykule przedstawiono ideę sterowania układem autonomicznego robota mobilnego skonstruowanego do celów edukacyjnych. Opisano strukturę mechaniczną układu, układy sensorów oraz zakres możliwości wynikających z działania oprogramowania robota.
-
The Behaviour Based Area Coverage of Unknown Environment by Autonomous Mobile Robot Using Modified ''The Way of the Ox'' Algorithm
PublikacjaPrzedstawiono propozycję rozwiązania zagadnienie całkowitego pokrycia terenu w układzie autonomicznego robota mobilnego. W tym celu zmodyfikowano algorytm "siewcy" oraz opracowano odpowiedni model układu, w środowisku Matlab-Simulink. Wykonano serię badań symulacyjnych, których najistotniejsze wyniki opisano w artykule.
-
Localization of Mobile Robot Using Radio Waves
PublikacjaOpisano systemy lokalizacji robotów mobilnych wykorzystujące metody triangulacji i trilateracji, w przestrzeniach dwuwymiarowych. Zaproponowano metodę pomiaru odległości drogą radiową oraz przedstawiono uzyskane wyniki badań.
-
Comparison the Accuracy of the Extrapolation Methods of the Time Phase Coincidence in Synchronization of Power Generating Units
PublikacjaW artykule opisano metody ekstrapolacji chwili zgodności fazowej napięć łączonych obiektów elektroenergetycznych. Przeprowadzono analizę porównawczą wybranych metod ekstrapolacji w równych warunkach pracy oraz przedstawiono najistotniejsze wyniki badań.
-
Modelling of Geared Multi-Rotor System
PublikacjaIn the paper the method of modelling a speed-varying geared rotor system is presented. The proposed approach enables us to obtain an accurate low-order lumped parameter representation of the investigated system. The final model consists of reduced modal models of an undamped beam/torsional shaft system as well as a spatially lumped model of other linear and nonlinear phenomena including gear mesh interaction.
-
The Influence of Modelling Material Zones on Strains and Stresses at Weld Toe Notch
PublikacjaThe latest development in the field of welding technology enabled prefabrication of thin-walled sandwich structures in an industrial scale. Sandwich structures fabricated of steel, or aluminium alloy plates and stiffeners are welded with the use of hi-power CO2 lasers. Strength analysis of such structures with the use of finite element method needs proper material modelling.In this paper the material model of steel sandwich panel...
-
Multi Parameter Sliding Test Result Evaluation for The Selection of Material Pair for Wear Resistant Components of a Hydraulic motor Dedicated for Use With Environmentally Friendly Working Fluids
PublikacjaIn the paper the method and results are presented of the testing of tribological performance of a number of hard materials available commercially. The tests consisted in unidirectional sliding with liquid lubrication. The load and velocity regime chosen were similar to a standard four-ball lubricity test with constant velocity and load increasing over time. The regime was modified in such a way that over the initial part of the...
-
Influence of Spatial Structures of 316L Stainless Steel on Its Cavitation Erosion Resistance
PublikacjaCavitation erosion performance of modified macroscopic internal structure 316L stainless steel was investigated. The samples processed by means of SLM method were subjected to cavitation erosion test. The scanning electron microscope Philips 30/ESEM was used to examine morphology of eroded surface.
-
Effect of Some Sulphur Additives on The Degradation of 9Cr-1Mo Steel After Its 10 Years Service in The CCR Platforming Unit
PublikacjaThe work shows the results of the tests of 9Cr-1Mo steel, which was for 10 years operated in the CCR platforming unit in Group Lotos SA in Gdańsk, and then in the laboratory was sulphidised during 166 h at a temperature of 600 °C. Sulphidation was performed in a mixture of H2-H2S gases at the vapour pressure of sulphur 4.1·10-14 atm, so the order of magnitude of vapour pressure was less than that of the dissociation pressure of...
-
Wear and corrosion characteristics of the layers type (mn-p) formed on aluminium alloys
Publikacjaopisano multipleksową metodę wytwarzania warstw zawierających mangan i fosfor (mn-p) na stopach aluminium. przedstawiono wyniki badań mikrostruktury, właściwości tribologicznych i korozyjnych tych warstw. stwierdzono obecność tlenku manganu i fosforku manganu w wytworzonych warstwach oraz ich wysoką twardość, rzędu 1272 hv0,02. warstwy typu (mn-p) zmniejszają podatność stopu alsi13mg1cuni na korozję w 0,01 mh2so4.
-
Indoor atmospheric degradation of historical metal objects studied by spectroscopic techniques
Publikacja -
Perovskites in Solid Oxide Fuel Cells
PublikacjaPrzeglądowa publikacja dotycząca wykorzystania ceramicznych materiałów perowskitowych w tlenkowych ogniwach paliwowych.
-
Preparation and characterization of TiO2 nanostructures for catalytic CO2 photoconversion
PublikacjaThe titanium dioxide target (99.7%) of 1 cm in dia was ablated in vacuum by laser pulses(6 ns) at 266 nm and at repetition rate of 10 Hz. During deposition the laser fluence between 1 and 3.5 J/cm2 and the O2 pressure from the range of 10-2 - 1 Pa were applied. The thin TiO2 films were deposited on glass substrate (1 × 1 cm2) heated up to 500 °C. The chemical composition of the film and samples produced by annealing were investigated...
-
Influence of spatial structures of 316L stainless steel on its cavitation erosion resistance
Publikacja -
Influence of type of material on performance of hydraulic components in thermal shock conditions
PublikacjaDuring the start-up of a hydraulic system in low ambient temperatures an incorrect operation may occur. The principles and conditions of safely operating hydraulic driven machines and devices are essential to designers and operators. For this reason the author of this article has conducted a series of tests on hydraulic components and systems in thermal shock conditions (cooled-down components were supplied with hot working medium)....
-
Comparison of Single and Multi-Population Evolutionary Algorithm for Path Planning in Navigation Situation
PublikacjaIn this paper a comparison of single and multi-population evolutionary algorithm is presented. Tested algorithms are used to determine close to optimal ship paths in collision avoidance situation. For this purpose a path planning problem is defined. A specific structure of the individual path and fitness function is presented. Principle of operation of single-population and multi-population evolutionary algorithm is described....
-
Wear of Electroplated Tools Used for Flat Grinding of Ceramics
PublikacjaTwo methods for the abrasive properties evaluation, based on the image processing, are presented in the paper. Image processing analysis was developed to evaluate quickly the abrasive properties as the tool wears down. The coefficient based on the image brightness was calculated and additional analysis was based on the number of grains located on the active surface of the tool before and after machining. The active surfaces of...
-
Surface Structure of Components Created by Stereolitography
PublikacjaStereolithography is an additive rapid prototyping method. This method is based on the principle of solidifying a liquid photopolymer (resin) by laser radiation. Models obtained with this method are characterized by a specific surface structure called “stairstep effect”. It causes that, the surface should be processed by additional finishing (postprocessing). To minimize the additional machining process, the model should be set...
-
Research on Tool Temperature Dependence on Lapping Grains Size
PublikacjaCommonly used as a finishing operation, lapping has been used for achieving ultra-high finishes and close tolerances between mating pieces. Its carried out by applying loose abrasive grains between work and lap surfaces, and causing a relative motion between them resulting in a finish of multi-directional lay. The grains activity (sliding and rolling) in the working gap causes not only the material removal but also the temperature...
-
The Influence of Workpiece Hardness on Plate Temperature during One Side Lapping
PublikacjaLapping leads to a surface with low roughness and high precision. Because of required parts accuracy tool flatness is the key to the successful machining. To avoid its excessive thermal expansion, plate temperature research was taken. The goal was to determine the correlation between the basic lapping conditions and wheel temperature. In work Bulsara et al. authors developed model to estimate the maximum and average temperature...
-
A simplified model of 3-D pipe system conveying flowing liquid
PublikacjaThe paper presents a model reduction technique of a 3-D pipe system with flowing liquid. In the analysis and design of control (mechatronic) systems it is useful to work with simple, low order models. A hybrid reduced order model is proposed. The system model consists of two parts, the modal model and the finite element model.
-
Influence of Flat Lapping Kinematics on Machinability of Ceramics
PublikacjaNew tools for flat grinding of ceramics are presented in the paper. Electroplated CBN tools (B64 and B107) were used in a modified single-disc lapping machine configuration. The results from experiments, such as the material removal rate and surface roughness parameters are presented and analyzed. Numerical simulations, based on the model for the shape error and tool wear estimation in machining with flat lapping kinematics, are...
-
Technological Problems in Lapping on Flat Surfaces of Ceramic Parts
PublikacjaThis paper will present the results of research on single-disc lapping of flat surfaces of small ceramic elements. Machining with the use of different tools such as metallic, two-metallic and abrasive-metallic will be analyzed. The basics and techniques of reinforcement of laps will be discussed. The results of the influence of parameters on the surface quality of ceramic conponents (sealing) for three treatments on lapping machines...
-
HILS for the Design of Three-Wheeled Mobile Platform Motion Surveillance System with a Use of Energy Performance Index
PublikacjaCurrent tendency in mechatronic design requires the use of comprehensive development of an environment, which gives the possibility to prototype, design, simulate and integrate with dedicated hardware. The paper discusses the Hardware-In-the-Loop Simulations (HILS) mechatronic technique, used during the design of the surveillance system based on energy performance index. The presented test configuration (physical controller – emulated...
-
Identification of Kinematic Excitation Function by the Modal Coordinates Estimation of the System's Dynamics
PublikacjaThe paper presents a method of the kinematic excitation courses’ identification in excitation points, based on the car road test acceleration at different measurement points. For the purpose of the laboratory fatigue life investigation of contemporary complex structures (e.g. cars bodies) and components of these structures (i.e. cars roofs), only a few first vibration modes are usually taken into account. During real life tests...
-
Using River Formation Dynamics Algorithm in Mobile Robot Navigation
PublikacjaRiver Formation Dynamics is a heuristic optimization algorithm based on the manner, in which drops of water form the river bed. The idea is to imitate the movement of drops on the edges between given nodes thus performing a search based on their height, which is modified through the mechanism of soil erosion and sediment deposition. In this way decreasing gradients are constructed, and these are followed by subsequent drops to...
-
Behavior Based Complete Coverage Task of Unknown Area by an Autonomous Mobile Robot SCORPION with Static Obstacles in Environment
PublikacjaIn the paper the behavior based control system of an autonomous mobile robot SCORPION is presented to execute the one of the most difficult navigation task, which is the complete coverage task of unknown area with static obstacles in the environment. The main principle assumed to design control system was that the robot should cover all area only once, if it possible, to optimize the length of path and energy consumption. All commercial...
-
Studies of the Modelling Accuracy of Steam Turbine Control Systems for Diagnostic Tests of Automatic Synchronizers
PublikacjaOne of the important factors that affect the reliable operation of the power system and the rapid restitution after disaster is a quick and effective combining synchronous electric power facilities to operate in parallel. Hence, diagnostics of automatic synchronizers at every stage of their life, from building a prototype, through the whole life, until removing such devices from the operation, is an extremely important and responsible...
wyświetlono 1203 razy