Patryk Błaszczak - Dane badawcze

mgr inż. Patryk Błaszczak

Zatrudnienie

Doktorant w Szkoła Doktorska
Doktorant w Instytut Nanotechnologii i Inżynierii Materiałowej
Doktorant w Laboratorium Materiałów Funkcjonalnych ETI

Obszary badawcze

seria: Impact of strontium non-stoichiometry of SrxTi0.3Fe0.7O3-δ liczba: 6

rozwiń zwiń

Particle size distributions (PSD) and the specific surface area (BET) results for SrxTi0.30Fe0.70O3-d materials
Dane Badawcze
- A. Mroziński
- P. Błaszczak
- seria: Impact of strontium non-stoichiometry of SrxTi0.3Fe0.7O3-δ
This dataset contains results of particle size distributions (PSD) and BET measuremnt fot SrxTi0.30Fe0.70O3-d materials (x=0.90, 0.95, 1.00 and 1.05). The PSD of the powders were obtained using a Zetasizer Nano dynamic light scattering analyser (Malvern Panalytica). Measurements of the STF70-x solution in ethanol using backscattering mode .
X-ray diffractometry results of the Sr1.05Ti0.30Fe0.70O3-d material before and after H2-TPR measurement
Dane Badawcze
- seria: Impact of strontium non-stoichiometry of SrxTi0.3Fe0.7O3-δ
This dataset contains results of X-ray diffractometry mesurement (XRD) of the Sr1.05Ti0.30Fe0.70O3-d material. The phase composition of the investigated powders was analyzed by XRD at room temperature. The X-ray diffractometry (XRD) technique was used to determine the phase composition of the fabricated powder and powder after H2-TPR (temperature programmed...
X-ray diffractometry results of the Sr1.00Ti0.30Fe0.70O3-d material before and after H2-TPR measurement
Dane Badawcze
- seria: Impact of strontium non-stoichiometry of SrxTi0.3Fe0.7O3-δ
This dataset contains results of X-ray diffractometry mesurement (XRD) of the Sr1.00Ti0.30Fe0.70O3-d material. The phase composition of the investigated powders was analyzed by XRD at room temperature. The X-ray diffractometry (XRD) technique was used to determine the phase composition of the fabricated powder and powder after H2-TPR (temperature programmed...
X-ray diffractometry results of the Sr0.95Ti0.30Fe0.70O3-d material before and after H2-TPR measurement
Dane Badawcze
- seria: Impact of strontium non-stoichiometry of SrxTi0.3Fe0.7O3-δ
This dataset contains results of X-ray diffractometry mesurement (XRD) of the Sr0.95Ti0.30Fe0.70O3-d material. The phase composition of the investigated powders was analyzed by XRD at room temperature. The X-ray diffractometry (XRD) technique was used to determine the phase composition of the fabricated powder and powder after H2-TPR (temperature programmed...
X-ray diffractometry results of the Sr0.90Ti0.30Fe0.70O3-d material before and after H2-TPR measurement
Dane Badawcze
- seria: Impact of strontium non-stoichiometry of SrxTi0.3Fe0.7O3-δ
This dataset contains results of X-ray diffractometry mesurement (XRD) of the Sr0.90Ti0.30Fe0.70O3-d material. The phase composition of the investigated powders was analyzed by XRD at room temperature. The X-ray diffractometry (XRD) technique was used to determine the phase composition of the fabricated powder and powder after H2-TPR (temperature programmed...
Impact of strontium non-stoichiometry of SrxTi0.3Fe0.7O3-δ
Dane Badawcze
- seria: Impact of strontium non-stoichiometry of SrxTi0.3Fe0.7O3-δ
This dataset contains results of the research on the basis of which the Figures presented in the manuscript entitled "Impact of strontium non-stoichiometry of SrxTi0.3Fe0.7O3-δ on structural, electrical, and electrochemical properties for potential oxygen electrode of intermediate temperature Solid Oxide Cells" were prepared. A detailed description...

seria: Ceria liczba: 3

rozwiń zwiń

FTIR spectra of Ce0.9M0.1O2 synthesised by reverse microemulsion method
Dane Badawcze
- seria: Ceria
The dataset consist of the FTIR spectra of Ce0.9M0.1O2 synthesised by reverse microemulsion method, after calcination at 500 degrees.
The XAS spectra of O-K edges, M-L edges and Ce-M edges in Ce0.9M0.1O2
Dane Badawcze
- seria: Ceria
The dataset consists of XAS spectra of O-K edges, M-L edges of Ce0.9M0.1O2 (where M=Mn, Fe, Co, Ni, Cu) synthesised by reverse microemulsion method. XAS spectra were collected at PIRX beamline in SOLARIS National Synchrotron Radiation Centre. Measurements were perfomed under ultra high vacuum in total electron yield (TEY) mode.
The TPR reduction profile of Ce0.9M0.1O2
Dane Badawcze
- seria: Ceria
The dataset includes the TPR reduction profiles of Ce0.9M0.1O2 (where M=Mn, Fe, Co, Ni, Cu) nanopowders prepared by the reverse microemulsion method. After the synthesis powders were dried, then calcined at 500 degrees for 2 h. The measurements were carried out in H2/Ar mixture from 100C to 900C. Gas flow:40ml/min and temperature ramp: 10deg/min.

seria: DIR-SOFC liczba: 43

rozwiń zwiń

The XPS spectra of ZrO2/5%Cu prepared using wet impregnation method
Dane Badawcze
- seria: DIR-SOFC
The dataset includes XPS spectra of ZrO2/5%Cu catalyst sintered under air atmosphere. Samples were produced using aqueous soft chemistry methods and incipient wettness impregnation using nitrate solution. The XPS spectra were collected for all species.
The XPS spectra of SrTiO3/5%Cu prepared using wet impregnation method
Dane Badawcze
- seria: DIR-SOFC
The dataset includes XPS spectra of SrTiO3/5%Cu catalyst sintered under air atmosphere. Samples were produced using aqueous soft chemistry methods and incipient wettness impregnation using nitrate solution. The XPS spectra were collected for all species.
The XPS spectra of Al2O3/5%Cu prepared using wet impregnation method
Dane Badawcze
- seria: DIR-SOFC
The dataset includes XPS spectra of Al2O3/5%Cu catalyst sintered under air atmosphere. Samples were produced using aqueous soft chemistry methods and incipient wettness impregnation using nitrate solution. The XPS spectra were collected for all species.
FTIR spectra of gas mixtures from the process of biogas dry reforming using CeO2/5%Cu catalyst
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
- seria: DIR-SOFC
The dataset contains the FTIR spectra collected during the catalytic measurements of dry reforming of biogas (60/40 CH4-CO2) using CeO2/5%Cu nanocatalyst. The specatra were collected every 1 minute from 800C to 500C. Reagent flow was set to 20ml/min.
The XPS spectra of CeO2/5%Cu prepared using wet impregnation method
Dane Badawcze
- seria: DIR-SOFC
The dataset includes XPS spectra of CeO2/5%Cu catalyst sintered under air atmosphere. Samples were produced using aqueous soft chemistry methods and incipient wettness impregnation using nitrate solution. The XPS spectra were collected for all species.
The XPS spectra of AlOOH/5%Cu prepared using wet impregnation method
Dane Badawcze
- seria: DIR-SOFC
The dataset includes XPS spectra of AlOOH/5%Cu catalyst sintered under air atmosphere. Samples were produced using aqueous soft chemistry methods and incipient wettness impregnation using nitrate solution. The XPS spectra were collected for all species.
The XPS spectra of AlOOH/1%Cu prepared using wet impregnation method
Dane Badawcze
- seria: DIR-SOFC
The dataset includes XPS spectra of AlOOH/1%Cu catalyst sintered under air atmosphere. Samples were produced using aqueous soft chemistry methods and incipient wettness impregnation using nitrate solution. The XPS spectra were collected for all species.
FTIR spectra of gas mixtures from the process of biogas dry reforming using Al2O3/5%Cu catalyst
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
- seria: DIR-SOFC
The dataset contains the FTIR spectra collected during the catalytic measurements of dry reforming of biogas (60/40 CH4-CO2) using AlOOH/1%Cu nanocatalyst. The specatra were collected every 1 minute from 800C to 500C. Reagent flow was set to 20ml/min.
FTIR spectra of gas mixtures from the process of biogas dry reforming using Al2O3/5%Cu catalyst
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
- seria: DIR-SOFC
The dataset contains the FTIR spectra collected during the catalytic measurements of dry reforming of biogas (60/40 CH4-CO2) using Al2O3 (TMDAR)/5%Cu nanocatalyst. The specatra were collected every 1 minute from 800C to 500C. Reagent flow was set to 20ml/min.
FTIR spectra of gas mixtures from the process of biogas dry reforming using alumina catalyst - blank
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
- seria: DIR-SOFC
The dataset contains the FTIR spectra collected during the catalytic measurements of blank sample Al2O3 for dry reforming of biogas (60/40 CH4-CO2). The specatra were collected every 1 minute.
FTIR spectra of gas mixtures from the process of biogas dry reforming using CLO catalyst
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
- seria: DIR-SOFC
The dataset contains the FTIR spectra collected during the catalytic measurements of dry reforming of biogas (60/40 CH4-CO2) using Ce0.8La0.2O2 nanocatalyst. The specatra were collected every 1 minute.
FTIR spectra of gas mixtures from the process of biogas dry reforming using CLO/Cu catalyst
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
- seria: DIR-SOFC
The dataset contains the FTIR spectra collected during the catalytic measurements of dry reforming of biogas (60/40 CH4-CO2) using Ce0.8La0.2O2+10wt.%Cu nanocatalyst. The specatra were collected every 1 minute.
FTIR spectra of gas mixtures from the process of biogas dry reforming using CeO2/Cu catalyst
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
- seria: DIR-SOFC
The dataset contains the FTIR spectra collected during the catalytic measurements of dry reforming of biogas (60/40 CH4-CO2) using CeO2+10wt.%Cu nanocatalyst. The specatra were collected every 1 minute.
The electrical properties mesurements of DIR-SOFC with Ce0.8Cu0.2O2-s functional layer
Dane Badawcze
- B. Bochentyn
- P. Błaszczak
- seria: DIR-SOFC
The dataset includes the electrical properties mesurements of SOFC with Ce0.8Cu0.1O2-s layer. Samples were produced using aqueous soft chemistry methods (microemulsion method) and applied in form of a layer onto the anode of the commercial SOFC. The SOFC was working under biogas feeding at 750oC. The layers were sintered at 1100oC.
The electrical properties mesurements of DIR-SOFC with CeO2-s functional layer
Dane Badawcze
- B. Bochentyn
- P. Błaszczak
- seria: DIR-SOFC
The dataset includes the electrical properties mesurements of SOFC with CeO2-s layer. Samples were produced using aqueous soft chemistry methods (microemulsion method) and applied in form of a layer onto the anode of the commercial SOFC. The SOFC was working under biogas feeding at 750oC. The layers were sintered at 1100oC.
The electrical properties mesurements of DIR-SOFC with Ce0.8Ni0.2O2-s functional layer
Dane Badawcze
- B. Bochentyn
- P. Błaszczak
- seria: DIR-SOFC
The dataset includes the electrical properties mesurements of SOFC with Ce0.8Ni0.1O2-s layer. Samples were produced using aqueous soft chemistry methods (microemulsion method) and applied in form of a layer onto the anode of the commercial SOFC. The SOFC was working under biogas feeding at 750oC. The layers were sintered at 1100oC.
The electrical properties mesurements of DIR-SOFC with Ce0.8Fe0.2O2-s functional layer
Dane Badawcze
- B. Bochentyn
- P. Błaszczak
- seria: DIR-SOFC
The dataset includes the electrical properties mesurements of SOFC with Ce0.8Fe0.1O2-s layer. Samples were produced using aqueous soft chemistry methods (microemulsion method) and applied in form of a layer onto the anode of the commercial SOFC. The SOFC was working under biogas feeding at 750oC. The layers were sintered at 1100oC.
The electrical properties mesurements of DIR-SOFC with Ce0.8Mn0.2O2-s functional layer
Dane Badawcze
- B. Bochentyn
- P. Błaszczak
- seria: DIR-SOFC
The dataset includes the electrical properties mesurements of SOFC with Ce0.8Mn0.1O2-s layer. Samples were produced using aqueous soft chemistry methods (microemulsion method) and applied in form of a layer onto the anode of the commercial SOFC. The SOFC was working under biogas feeding at 750oC. The layers were sintered at 1100oC.
The electrical properties mesurements of DIR-SOFC with Ce0.8Co0.2O2-s functional layer
Dane Badawcze
- B. Bochentyn
- P. Błaszczak
- seria: DIR-SOFC
The dataset includes the electrical properties mesurements of SOFC with Ce0.8Co0.1O2-s layer. Samples were produced using aqueous soft chemistry methods (microemulsion method) and applied in form of a layer onto the anode of the commercial SOFC. The SOFC was working under biogas feeding at 750oC. The layers were sintered at 1100oC.
The XPS spectra of Ce0.8Cu0.2O2 prepared using microemulsion method
Dane Badawcze
- seria: DIR-SOFC
The dataset includes XPS spectra of Ce0.8Cu0.2O2-s sintered under air atmosphere. Samples were produced using aqueous soft chemistry methods (microemulsion). The XPS spectra were collected for all species.
The XPS spectra of Ce0.8Ni0.2O2 prepared using microemulsion method
Dane Badawcze
- seria: DIR-SOFC
The dataset includes XPS spectra of Ce0.8Ni0.2O2-s sintered under air atmosphere. Samples were produced using aqueous soft chemistry methods (microemulsion). The XPS spectra were collected for all species.
The XRD diffraction patterns of Ce(Gd,Pr)O2-s samples
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
- seria: DIR-SOFC
The dataset includes XRD diffraction patterns of Ce0.8Gd0.2O2-s and Ce0.8Pr0.2O2-s sintered at 600oC under air atmosphere for 4 h. Samples were produced using aqueous soft chemistry methods (Pechini).
Carbon activity coefficients of SOFC and SOFC with LSCNT layer fueled by biogas mixture at 750 C - longterm
Dane Badawcze
- B. Bochentyn
- P. Błaszczak
- seria: DIR-SOFC
The dataset contains the calculated carbon activity coefficient for the SOFC and SOFC with LSCNT layer (La0.27Sr0.54Ce0.09Ni0.1Ti0.9O3-s) fueled by synthetic biogas mixture (60:40 CH4:CO2). The outlet concentration of the gases from SOFC were measured using novel FTIR-based unit.
Reaction quotients of reforming reactions for SOFC and SOFC with LSCNT layer fueled by biogas mixture at 750 C - longterm
Dane Badawcze
- B. Bochentyn
- P. Błaszczak
- seria: DIR-SOFC
The dataset contains the calculated reaction quotients of reforming reactions for the SOFC and SOFC with LSCNT layer (La0.27Sr0.54Ce0.09Ni0.1Ti0.9O3-s) fueled by synthetic biogas mixture (60:40 CH4:CO2). The outlet concentration of the gases from SOFC were measured using novel FTIR-based unit.
Thermogravimetric measurement (TG) of 20wt.% Ce0.8La0.2O2-NiO-YSZ anode for DIR-SOFC
Dane Badawcze
- B. Bochentyn
- P. Błaszczak
- seria: DIR-SOFC
The daataset includes the thermogravimetric measurement (TG) of Ce0.8La0.2O2-NiO-YSZ anode for DIR-SOFC. The mesurement was performed under synthestic air atmosphere. The anode was composed of NiO-YSZ cermet composite (80 wt%) and Ce0.8La0.2O2-s additive (20wt%) with the addition of poroformer - PMMA granules 8um diameter (40 vol.% of whole powder volume)....
The changes of outlet gases concentrations from SOFC with Ce(Pr,Sm)O2-s layers
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
- seria: DIR-SOFC
The dataset includes The changes of outlet gases concentrations from SOFC with Ce(Pr,Sm)O2-s layers. Samples were produced using aqueous soft chemistry methods (microemulsion method) and applied in form of a layer onto the anode of the commercial SOFC. The SOFC was working under biogas feeding.
The electrical properties mesurements of SOFC with Ce0.8Sm0.2O2-s layer
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
- seria: DIR-SOFC
The dataset includes The electrical properties mesurements of SOFC with Ce0.8Sm0.2O2-s layer. Samples were produced using aqueous soft chemistry methods (microemulsion method) and applied in form of a layer onto the anode of the commercial SOFC. The SOFC was working under biogas feeding.
Thermogravimetric measurement (TG) of 10 wt.% Ce0.8La0.2O2-NiO-YSZ anode for DIR-SOFC
Dane Badawcze
- B. Bochentyn
- P. Błaszczak
- seria: DIR-SOFC
The daataset includes the thermogravimetric measurement (TG) of Ce0.8La0.2O2-NiO-YSZ anode for DIR-SOFC. The mesurement was performed under synthestic air atmosphere. The anode was composed of NiO-YSZ cermet composite (90 wt%) and Ce0.8La0.2O2-s additive (10wt%) with the addition of poroformer - PMMA granules 8um diameter (40 vol.% of whole powder volume)....
The electrical properties mesurements of SOFC with Ce0.8Pr0.05Sm0.15O2-s layer
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
- seria: DIR-SOFC
The dataset includes The electrical properties mesurements of SOFC with Ce0.8Pr0.05Sm0.15O2-s layer. Samples were produced using aqueous soft chemistry methods (microemulsion method) and applied in form of a layer onto the anode of the commercial SOFC. The SOFC was working under biogas feeding.
Change of reaction quotients for SOFC fueled by biogas mixture at 750 C
Dane Badawcze
- B. Bochentyn
- P. Błaszczak
- seria: DIR-SOFC
The dataset contains the Change of reaction quotients for SOFC fueled by biogas mixture at 750 C (60:40 CH4:CO2). The outlet concentration of the gases from SOFC were measured using novel FTIR-based unit.
Electrical measurement data for SOFC fueled by H2 and biogas mixture at 750 C
Dane Badawcze
- B. Bochentyn
- P. Błaszczak
- seria: DIR-SOFC
The dataset contains the Electrical measurement data for SOFC fueled by H2 (30h) and biogas mixture at 750 C (60:40 CH4:CO2). The investigation of long-term electrical stability was performed during initial SOFC feeding with hydrogen (for 30 h) and further with biogas (for 90 h). The electrical properties of the fuel cell were measured using the HAMEG...
The electrical properties mesurements of SOFC with Ce0.8Pr0.2O2-s layer
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
- seria: DIR-SOFC
The dataset includes The electrical properties mesurements of SOFC with Ce0.8Pr0.2O2-s layer. Samples were produced using aqueous soft chemistry methods (microemulsion method) and applied in form of a layer onto the anode of the commercial SOFC. The SOFC was working under biogas feeding.
The electrical properties mesurements of SOFC with Ce0.8Pr0.15Sm0.05O2-s layer
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
- seria: DIR-SOFC
The dataset includes The electrical properties mesurements of SOFC with Ce0.8Pr0.15Sm0.05O2-s layer. Samples were produced using aqueous soft chemistry methods (microemulsion method) and applied in form of a layer onto the anode of the commercial SOFC. The SOFC was working under biogas feeding.
Change of catalytic parameters for SOFC fueled by H2 and biogas mixture at 750 C
Dane Badawcze
- B. Bochentyn
- P. Błaszczak
- seria: DIR-SOFC
The dataset contains the Change of catalytic parameters for SOFC fueled by H2 and biogas mixture at 750 C (60:40 CH4:CO2). The outlet concentration of the gases from SOFC were measured using novel FTIR-based unit. The parameters are conversion rates, selectivities and yields of products
The electrical properties mesurements of SOFC with Ce0.8Pr0.1Sm0.1O2-s layer
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
- seria: DIR-SOFC
The dataset includes The electrical properties mesurements of SOFC with Ce0.8Pr0.1Sm0.1O2-s layer. Samples were produced using aqueous soft chemistry methods (microemulsion method) and applied in form of a layer onto the anode of the commercial SOFC. The SOFC was working under biogas feeding.
Change of exhaust gases concentration for SOFC fueled by H2 and biogas mixture at 750 C
Dane Badawcze
- B. Bochentyn
- P. Błaszczak
- seria: DIR-SOFC
The dataset contains the Change of exhaust gases concentration for SOFC fueled by H2 (for 12h) and biogas mixture at 750 C (60:40 CH4:CO2). The outlet concentration of the gases from SOFC were measured using novel FTIR-based unit.
Carbon balance of SOFC fueled by biogas mixture at 750 C
Dane Badawcze
- B. Bochentyn
- P. Błaszczak
- seria: DIR-SOFC
The dataset contains the calculated carbon balance for the SOFC fueled by synthetic biogas mixture (60:40 CH4:CO2). The outlet concentration of the gases from SOFC were measured using novel FTIR-based unit.
The XRD diffraction patterns of Ce(Pr,Sm)O2-s samples
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
- seria: DIR-SOFC
The dataset includes XRD diffraction patterns of Ce(Pr,Sm)O2-s samples of various stoichiometries of Pr and Sm dopants. Samples were produced using aqueous soft chemistry methods (microemulsion method).
Euilibrium composition of CH4-CO2-CO-H2-H2O-C system under biogas reforming conditions
Dane Badawcze
- B. Bochentyn
- P. Błaszczak
- seria: DIR-SOFC
The equilibrium compositions of CH4, CO2, CO, H2, H2O and C under the biogas mixture reforming were supplied with this dataset
Equilibrium constants (Keq) of reforming reactions
Dane Badawcze
- B. Bochentyn
- P. Błaszczak
- seria: DIR-SOFC
The equilibrium constants (K) of reforming reactions in SOFC were supplied with this dataset
Carbon dioxide (CO2) calibration set of FTIR spectra
Dane Badawcze
- B. Bochentyn
- P. Błaszczak
- seria: DIR-SOFC
The calibration spectra for CO2 concentration calibration were supplied with this dataset
Carbon (II) oxide (CO) calibration set of FTIR spectra
Dane Badawcze
- B. Bochentyn
- P. Błaszczak
- seria: DIR-SOFC
The calibration spectra for CO concentration calibration were supplied with this dataset
Methane (CH4) calibration set of FTIR spectra
Dane Badawcze
- B. Bochentyn
- P. Błaszczak
- seria: DIR-SOFC
The calibration spectra for CH4 concentration calibration were supplied with this dataset

seria: Exsolution liczba: 18

rozwiń zwiń

The EDS elemental maps of reduced LSCNT (SEM)
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
- seria: Exsolution
The dataset includes elemental maps of La, Ce, Ti, O, Sr, Ni in La0.27Sr0.54Ce0.09Ni0.1Ti0.9O3-s produced using Pechini method sintered at 1200oC under air atmosphere and reduced at 900 for 12 h in wet H2.
The TEC measurement of LSCNT (dilatometry) in air
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
- seria: Exsolution
The dataset includes dilatometry results for La0.27Sr0.54Ce0.09Ni0.1Ti0.9O3-s measured in air from 100 to 800C using Netzsch DIL 402 PC.
The XRD diffraction patterns of reduced LSCNT prepared using two methods and two sintering temperatures
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
- seria: Exsolution
The dataset includes XRD diffraction patterns of La0.27Sr0.54Ce0.09Ni0.1Ti0.9O3-s produced using two methods, namely organic (citrate assisted) and Pechini sintered at 1000 or 1200oC under air atmosphere and reduced at 900 for 12 h in wet H2.
FTIR spectra of SOFC with LSCNT layer fueled by biogas mixture at 750 C (pure)
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
- seria: Exsolution
The dataset contains the FTIR spectra collected during the electrical measurements DIR-SOFC with LSCNT layer. The SOFC was reduced at 800degC in H2 prior to mesurements. The spectra were collected every 10 min.
Electrical performance measurement of reference and SOFC with LSCNT layer fueled by H2 and 20ppm H2S/biogas mixture at 750 C - cyclic measurements (12h per cycle)
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
- seria: Exsolution
The dataset contains the electrical IV measurements collected during the cyclic measurements of H2S poisoning in DIR-SOFC with/-out LSCNT layer. The H2S poisoning and H2 regenrating cycles were 12 h each. The spectra were collected every 10 min.
FTIR spectra of SOFC with LSCNT layer fueled by H2 and 20ppm H2S/biogas mixture at 750 C - cyclic measurements (12h per cycle)
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
- seria: Exsolution
The dataset contains the FTIR spectra collected during the cyclic measurements of H2S poisoning in DIR-SOFC with LSCNT layer. The H2S poisoning and H2 regenrating cycles were 12 h each. The spectra were collected every 10 min.
FTIR spectra of reference SOFC fueled by H2 and 20ppm H2S/biogas mixture at 750 C - cyclic measurements (12h per cycle)
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
- seria: Exsolution
The dataset contains the FTIR spectra collected during the cyclic measurements of H2S poisoning in DIR-SOFC without LSCNT layer. The H2S poisoning and H2 regenrating cycles were 12 h each. The spectra were collected every 10 min.
Electrical power measurement of reference SOFC fueled by biogas mixture at 750 C
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
- seria: Exsolution
The dataset contains the electrical measurements of IV curves for SOFC without La0.27Sr0.54Ce0.09Ni0.1Ti0.9O3-s layer working under biogas and H2 feeding stream. The SOFC was reduced at 900C and conditioned for 12 h under H2 prior the measurements. The measurements were performed using Gamry potentiostat/galvanostat
Electrical power measurement of LSCNT modified SOFC fueled by biogas mixture at 750 C
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
- seria: Exsolution
The dataset contains the electrical measurements of IV curves for SOFC with La0.27Sr0.54Ce0.09Ni0.1Ti0.9O3-s layer working under biogas and H2 feeding stream. The SOFC was reduced at 900C and conditioned for 12 h under H2 prior the measurements. The measurements were performed using Gamry potentiostat/galvanostat
Change of exhaust gases concentration for LSCNT modified SOFC fueled by biogas mixture at 750 C
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
- seria: Exsolution
The dataset changes of exhaust gases concentrations (CH4,CO,CO2,H2) over working time for SOFC with La0.27Sr0.54Ce0.09Ni0.1Ti0.9O3-s layer. Concentrations were calculated based on the FTIR measurements and calibration files presented in coupled dataset.
The XRD diffraction patterns of LSCNT of different A site nonstoichiometry
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
- seria: Exsolution
The dataset includes XRD diffraction patterns of La0.27Sr0.54Ce0.09Ni0.1Ti0.9O3-s and La0.3Sr0.6Ce0.1Ni0.1Ti0.9O3-s sintered at 1200oC under air atmosphere for 12 h. Samples were produced using aqueous soft chemistry methods (Pechini).
The SEM images of LSCNT reduced at 1000 degrees C under H2
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
- seria: Exsolution
The dataset includes SEM images of La0.27Sr0.54Ce0.09Ni0.1Ti0.9O3-s sintered at 1200oC under air atmosphere for 12 h and reduced at 1000oC under H2 for 10 h. Samples were produced using aqueous soft chemistry methods (Pechini).
The SEM images of LSCNT reduced at 900 degrees C under H2
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
- seria: Exsolution
The dataset includes SEM image of La0.27Sr0.54Ce0.09Ni0.1Ti0.9O3-s sintered at 1200oC under air atmosphere for 12 h and reduced at 900oC under H2 for 10 h. Samples were produced using aqueous soft chemistry methods (Pechini).
The SEM images of LSCNT reduced at 800 degrees C under H2
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
- seria: Exsolution
The dataset includes SEM images of La0.27Sr0.54Ce0.09Ni0.1Ti0.9O3-s sintered at 1200oC under air atmosphere for 12 h and reduced at 800oC under H2 for 10 h. Samples were produced using aqueous soft chemistry methods (Pechini).
The SEM images of LSCNT sintered at 1200 degrees C in air
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
- seria: Exsolution
The dataset includes SEM images of La0.27Sr0.54Ce0.09Ni0.1Ti0.9O3-s sintered at 1200oC under air atmosphere for 12 h. Samples were produced using aqueous soft chemistry methods (Pechini). The grain structure can be seen on higher resolution image.
Change of exhaust gases concentration for reference SOFC and SOFC with LSCNT layer fueled by biogas mixture at 750 C
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
- seria: Exsolution
The dataset changes of exhaust gases concentrations (CH4,CO,CO2,H2) over working time for SOFC with La0.27Sr0.54Ce0.09Ni0.1Ti0.9O3-s layer as well as reference SOFEC (unmodified). Concentrations were calculated based on the FTIR measurements and calibration curves presented in different dataset. Longterm measurements of SOFC were performed using in-house...
The XPS spectra of LSCNT sintered at 1200C
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
- seria: Exsolution
The dataset includes XPS spectra of La0.27Sr0.54Ce0.09Ni0.1Ti0.9O3-s sintered at various temperatures under air atmosphere for 12 h. Samples were produced using aqueous soft chemistry methods (Pechini). The XPS spectra were collected for all species.
The XRD diffraction patterns of LSCNT sintered at various temperatures
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
- seria: Exsolution
The dataset includes XRD diffraction patterns of La0.27Sr0.54Ce0.09Ni0.1Ti0.9O3-s sintered at various temperatures under air atmosphere for 12 h. Samples were produced using aqueous soft chemistry methods (Pechini).

The XRD diffraction patterns of Ce0.9Gd0.1O2 prepared using soft template precipitation method
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
The dataset includes XRD patterns of Ce0.9Gd0.1O2-s nanopowder (nanoparticles) prepared using soft template precipitation method. CTAB was used as a micelle-based templating agent. The powders were precipitated from aqueous nitrate solution using NaOH solution and 25xCMC (critcal micelle concentration) of CTAB. Precipitates were heated up to 90oC,...
FTIR spectra of gas mixtures from the methanation chamber filled with 25-75wt.% NiO-Al2O3
Dane Badawcze
The dataset includes the FTIR spectra collection of the outlet gas mixtures (CO2, CO, CH4) from reactor chamber filled with 25/75 wt.% NiO-Al2O3 catalyst for perfoming methanation reaction. The inlet gas mixture was composed of 3:1 by vol. H2:CO. Spectra were collected using PerkinElmer FTIR every 1 min.
FTIR spectra of gas mixtures from the methanation chamber filled with 50-50wt.% NiO-GDC
Dane Badawcze
The dataset includes the FTIR spectra collection of the outlet gas mixtures (CO2, CO, CH4) from reactor chamber filled with 50/50 wt.% NiO-GDC (Gadolinia Doped Ceria 20mol.%Gd2O3) catalyst for perfoming methanation reaction. The inlet gas mixture was composed of 3:1 by vol. H2:CO. Spectra were collected using PerkinElmer FTIR every 1 min.
The TPR reduction profile of MCO powder
Dane Badawcze
The dataset includes the TPR reduction profiles of MnCo2O4 (MCO) commercial powder. The dataset includes a cycle of reduction under H2/Ar mixture from 100C to 900C. Gas flow:40ml/min and temperature ramp: 10deg/min. Degassed at 200C in He for 1 h.
FTIR spectra of gas mixtures from the methanation chamber filled with 50-50wt.% NiO-Al2O3
Dane Badawcze
The dataset includes the FTIR spectra collection of the outlet gas mixtures (CO2, CO, CH4) from reactor chamber filled with 50/50 wt.% NiO-Al2O3 catalyst for perfoming methanation reaction. The inlet gas mixture was composed of 3:1 by vol. H2:CO. Spectra were collected using PerkinElmer FTIR every 1 min.
The XRD diffraction patterns of Ce0.9Gd0.1O2 prepared using soft template precipitation method - 50xCMC
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
The dataset includes XRD patterns of Ce0.9Gd0.1O2-s nanopowder (nanoparticles) prepared using soft template precipitation method. CTAB was used as a micelle-based templating agent. The powders were precipitated from aqueous nitrate solution using NaOH solution and 50xCMC (critcal micelle concentration) of CTAB. Precipitates were heated up to 90oC,...
The XRD diffraction patterns of Ce0.9Gd0.1O2 prepared using modified Pechini/EDTA method
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
The dataset includes XRD patterns of Ce0.9Gd0.1O2-s nanopowder (nanoparticles) prepared using modified Pechini method consisting of CA (citric acid), PEG (propylene glycol) and EDTA. Exact amount of metal nitrates were dissolved in water followed by addition of gelling agents and heated to 100C. Obtained gel was calcined at 600C for 4h. The powder...
BET adsorption-desorption isotherm of CeO2 prepared using Pechini method
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
The dataset includes the isotherms of adortion and desorption of N2 at LN2 temperature. The sorption isotherms were obtained using Quatachrome NovaTouch LX1 equippment. The ceramic measured powder was composed of nanometric pure CeO2 prepared using modified Pechini method - citric acid and propylene glycol (2:1)
BET adsorption-desorption isotherm of CeO2 pure
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
The dataset includes the isotherms of adortion and desorption of N2 at LN2 temperature. The sorption isotherms were obtained using Quatachrome NovaTouch LX1 equippment. The ceramic measured powder was composed of nanometric pure CeO2 (CA-assisted method of synthesis)
BET adsorption-desorption isotherm of nano-ZrO2
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
The dataset includes the isotherms of adortion and desorption of N2 at LN2 temperature. The sorption isotherms were obtained using Quatachrome NovaTouch LX1 equippment. The ceramic measured powder was composed of nanometric ZrO2 (CA-assisted method of synthesis)
BET adsorption-desorption isotherm of nano-MgO
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
The dataset includes the isotherms of adortion and desorption of N2 at LN2 temperature. The sorption isotherms were obtained using Quatachrome NovaTouch LX1 equippment. The ceramic measured powder was composed of nanometric MgO (CA-assisted method of synthesis)
BET adsorption-desorption isotherm of nano-SrTiO3
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
The dataset includes the isotherms of adortion and desorption of N2 at LN2 temperature. The sorption isotherms were obtained using Quatachrome NovaTouch LX1 equippment. The ceramic measured powder was composed of nanometric SrTiO3 (CA-assisted method of synthesis)
BET adsorption-desorption isotherm of nano-CeO2
Dane Badawcze
The dataset includes the isotherms of adortion and desorption of N2 at LN2 temperature. The sorption isotherms were obtained using Quatachrome NovaTouch LX1 equippment. The catalyts powder composed of nanoCeO2 (AlfaAesar)
BET adsorption-desorption isotherm of nano-CeO2 impregnated with Fe
Dane Badawcze
The dataset includes the isotherms of adortion and desorption of N2 at LN2 temperature. The sorption isotherms were obtained using Quatachrome NovaTouch LX1 equippment. The catalyts powder composed of nanoCeO2 impreganted with Fe oxide nanoparticles with the usage of BCD (Beta-cyclodextrins) and without addition.
BET adsorption-desorption isotherm of nano-CeO2 impregnated with Mn
Dane Badawcze
The dataset includes the isotherms of adortion and desorption of N2 at LN2 temperature. The sorption isotherms were obtained using Quatachrome NovaTouch LX1 equippment. The catalyts powder composed of nanoCeO2 impreganted with Mn oxide nanoparticles with the usage of BCD (Beta-cyclodextrins) and without addition.
BET adsorption-desorption isotherm of nano-CeO2 impregnated with Cu
Dane Badawcze
The dataset includes the isotherms of adortion and desorption of N2 at LN2 temperature. The sorption isotherms were obtained using Quatachrome NovaTouch LX1 equippment. The catalyts powder composed of nanoCeO2 impreganted with Cu oxide nanoparticles with the usage of BCD (Beta-cyclodextrins) and without addition.
BET adsorption-desorption isotherm of nano-CeO2 impregnated with Ni
Dane Badawcze
The dataset includes the isotherms of adortion and desorption of N2 at LN2 temperature. The sorption isotherms were obtained using Quatachrome NovaTouch LX1 equippment. The catalyts powder composed of nanoCeO2 impreganted with Ni oxide nanoparticles with the usage of BCD (Beta-cyclodextrins) and without addition.
BET adsorption-desorption isotherm of nano-CeO2 impregnated with Co
Dane Badawcze
The dataset includes the isotherms of adortion and desorption of N2 at LN2 temperature. The sorption isotherms were obtained using Quatachrome NovaTouch LX1 equippment. The catalyts powder composed of nanoCeO2 impreganted with Co oxide nanoparticles with the usage of BCD (Beta-cyclodextrins) and without addition.
Euilibrium composition of CH4-CO2-CO-H2-H2O system for CO2/H2/H2O methanation
Dane Badawcze
- B. Bochentyn
- P. Błaszczak
The equilibrium compositions of CH4, CO2, CO, H2, H2O without C under the methanation reaction of 1:2 CO:H2 syngas mixtures were supplied with this dataset
Euilibrium composition of CH4-CO2-CO-H2-H2O-C system for CO2/H2/H2O methanation
Dane Badawcze
- B. Bochentyn
- P. Błaszczak
The equilibrium compositions of CH4, CO2, CO, H2, H2O and C under the methanation reaction of 1:2 CO:H2 syngas mixtures were supplied with this dataset
The XRD diffraction pattern of interdiffusion test in the CLO-NiO-YSZ system (30wt.%YSZ)
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
The dataset includes the XRD pure diffraction pattern of the interdiffusion system consisting of CLO (Ce0.8La0.2O2), NiO and 8YSZ (8mol.% Y2O3 stabilized ZrO2). The mixture contains equal amounts of CLO and NiO as well as 30wt.% 8YSZ. Samples were sintered at 1400 oC. The reaction between CLO and YSZ is visible.
The XRD diffraction pattern of interdiffusion test in the CLO-NiO-YSZ system (20wt.%YSZ)
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
The dataset includes the XRD pure diffraction pattern of the interdiffusion system consisting of CLO (Ce0.8La0.2O2), NiO and 8YSZ (8mol.% Y2O3 stabilized ZrO2). The mixture contains equal amounts of CLO and NiO as well as 20wt.% 8YSZ. Samples were sintered at 1400 oC. The reaction between CLO and YSZ is visible.
The XRD diffraction pattern of interdiffusion test in the CLO-NiO-YSZ system (10wt.%YSZ)
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
The dataset includes the XRD pure diffraction pattern of the interdiffusion system consisting of CLO (Ce0.8La0.2O2), NiO and 8YSZ (8mol.% Y2O3 stabilized ZrO2). The mixture contains equal amounts of CLO and NiO as well as 10wt.% 8YSZ. Samples were sintered at 1400 oC. The reaction between CLO and YSZ is visible.
The TPO oxidation profile of CeO2/10wt.%Cu without BCD - prereduced
Dane Badawcze
The dataset includes the TPO oxidation profiles of CeO2/10wt.%Cu. The samples of nanoCeO2 impregnated without BCD-assisted precursor solution (betacyclodextrin). The dataset includes oxidation profile of the prereduced sample.
The TPO oxidation profile of CeO2/10wt.%Mn with BCD - prereduced
Dane Badawcze
The dataset includes the TPO oxidation profiles of CeO2/10wt.%Mn. The samples of nanoCeO2 impregnated with BCD-assisted precursor solution (betacyclodextrin). The dataset includes oxidation profile of the prereduced sample.
The XRD pattern of CeO2/10wt.%Ni with BCD
Dane Badawcze
The dataset includes the XRD pattern of CeO2/10wt.%Ni. The samples of nanoCeO2 were impregnated with BCD-assisted precursor nitrate solution (betacyclodextrin). The dataset includes 5-90 2 theta degree measurement. Nonreduced. Sintered at 400oC for 4h.
The XRD pattern of CeO2/10wt.%Fe prepared with BCD
Dane Badawcze
The dataset includes the XRD pattern of CeO2/10wt.%Fe. The samples of nanoCeO2 were impregnated with BCD-assisted precursor solution (betacyclodextrin). The dataset includes the 5-90 2theta degree measurement. Nonreduced. Sintered at 400oC for 4 h in air.
The XRD pattern of CeO2/10wt.%Cu prepared with BCD
Dane Badawcze
The dataset includes the XRD pattern of CeO2/10wt.%Cu. The samples of nanoCeO2 were impregnated with BCD-assisted precursor solution (betacyclodextrin). The dataset includes the 5-90 2theta degree measurement. Nonreduced. Sintered at 400oC for 4 h in air.
The XRD pattern of CeO2/10wt.%Cu prepared without BCD
Dane Badawcze
The dataset includes the XRD pattern of CeO2/10wt.%Cu. The samples of nanoCeO2 were impregnated without BCD-assisted precursor solution (betacyclodextrin) - pure nitarte solution 1M. The dataset includes the 5-90 2theta degree measurement. Nonreduced. Sintered at 400oC for 4 h in air.
The XRD pattern of CeO2/10wt.%Co prepared without BCD
Dane Badawcze
The dataset includes the XRD pattern of CeO2/10wt.%Co. The samples of nanoCeO2 were impregnated without BCD-assisted precursor solution (betacyclodextrin) - pure nitarte solution 1M. The dataset includes the 5-90 2theta degree measurement. Nonreduced. Sintered at 400oC for 4 h in air.
The TPO oxidation profile of CeO2/10wt.%Cu with BCD - prereduced
Dane Badawcze
The dataset includes the TPO oxidation profiles of CeO2/10wt.%Cu. The samples of nanoCeO2 impregnated with BCD-assisted precursor solution (betacyclodextrin). The dataset includes oxidation profile of the prereduced sample.
The TPR reduction profile of CeO2/10wt.%Cu without BCD - 2 cycles
Dane Badawcze
The dataset includes the TPR reduction profiles of CeO2/10wt.%Cu. The samples of nanoCeO2 impregnated without BCD-assisted precursor solution (betacyclodextrin). The dataset includes two cycles of reduction (samples oxidized in between)
The XRD pattern of CeO2/10wt.%Mn prepared with BCD
Dane Badawcze
The dataset includes the XRD pattern of CeO2/10wt.%Mn. The samples of nanoCeO2 were impregnated with BCD-assisted precursor solution (betacyclodextrin). The dataset includes the 5-90 2theta degree measurement. Nonreduced. Sintered at 400oC for 4 h in air.
The XRD pattern of CeO2/10wt.%Mn prepared without BCD
Dane Badawcze
The dataset includes the XRD pattern of CeO2/10wt.%Mn. The samples of nanoCeO2 were impregnated without BCD-assisted precursor solution (betacyclodextrin) - pure nitarte solution 1M. The dataset includes the 5-90 2theta degree measurement. Nonreduced. Sintered at 400oC for 4 h in air.
The TPO oxidation profile of CeO2/10wt.%Ni with BCD - prereduced
Dane Badawcze
The dataset includes the TPO oxidation profiles of CeO2/10wt.%Ni. The samples of nanoCeO2 impregnated with BCD-assisted precursor solution (betacyclodextrin). The dataset includes oxidation profile of the prereduced sample.
The TPR reduction profile of CeO2/10wt.%Ni without BCD - 2 cycles
Dane Badawcze
The dataset includes the TPR reduction profiles of CeO2/10wt.%Ni. The samples of nanoCeO2 impregnated without BCD-assisted precursor solution (betacyclodextrin). The dataset includes two cycles of reduction (samples oxidized in between)
The TPR reduction profile of CeO2/10wt.%Co without BCD - 2 cycles
Dane Badawcze
The dataset includes the TPR reduction profiles of CeO2/10wt.%Co. The samples of nanoCeO2 impregnated without BCD-assisted precursor solution (betacyclodextrin). The dataset includes two cycles of reduction (samples oxidized in between)
The XRD diffraction patterns of Sr2Al0.1Fe1.4Mo0.5O6 powder calcined at 1100oC in air
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
The dataset includes XRD patterns of Sr2Al0.1Fe1.4Mo0.5O6 powder prepared using wet chemistry methods, namely modified Pechini route. The powders were sintered at 1100oC for 12 h in air.
The XRD diffraction patterns of Sr1.9Fe1.4Ni0.1Mo0.5O6 powder calcined at 1100oC in air
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
The dataset includes XRD patterns of Sr1.9Fe1.4Ni0.1Mo0.5O6 powder prepared using wet chemistry methods, namely modified Pechini route. The powders were sintered at 1100oC for 12 h in air.
The TPO oxidation profile of CeO2/10wt.%Fe with BCD - prereduced
Dane Badawcze
The dataset includes the TPO oxidation profiles of CeO2/10wt.%Fe. The samples of nanoCeO2 impregnated with BCD-assisted precursor solution (betacyclodextrin). The dataset includes oxidation profile of the prereduced sample.
The TPO oxidation profile of CeO2/10wt.%Co with BCD - prereduced
Dane Badawcze
The dataset includes the TPO oxidation profiles of CeO2/10wt.%Co. The samples of nanoCeO2 impregnated with BCD-assisted precursor solution (betacyclodextrin). The dataset includes oxidation profile of the prereduced sample.
The XRD pattern of CeO2/10wt.%Ni prepared without BCD
Dane Badawcze
The dataset includes the XRD pattern of CeO2/10wt.%Ni. The samples of nanoCeO2 were impregnated without BCD-assisted precursor solution (betacyclodextrin) - pure nitarte solution 1M. The dataset includes the 5-90 2theta degree measurement. Nonreduced. Sintered at 400oC for 4 h in air.
The XRD pattern of CeO2/10wt.%Fe prepared without BCD
Dane Badawcze
The dataset includes the XRD pattern of CeO2/10wt.%Fe. The samples of nanoCeO2 were impregnated without BCD-assisted precursor solution (betacyclodextrin) - pure nitarte solution 1M. The dataset includes the 5-90 2theta degree measurement. Nonreduced. Sintered at 400oC for 4 h in air.
The XRD pattern of CeO2/10wt.%Ni prepared with BCD
Dane Badawcze
The dataset includes the XRD pattern of CeO2/10wt.%Ni. The samples of nanoCeO2 were impregnated with BCD-assisted precursor solution (betacyclodextrin). The dataset includes the 5-90 2theta degree measurement. Nonreduced. Sintered at 400oC for 4h in air.
The XRD pattern of CeO2/10wt.%Co prepared with BCD
Dane Badawcze
The dataset includes the XRD pattern of CeO2/10wt.%Co. The samples of nanoCeO2 were impregnated with BCD-assisted precursor solution (betacyclodextrin). The dataset includes the 5-90 2theta degree measurement.
The XRD diffraction patterns of Sr1.9Fe1.5Mo0.5O6 powder calcined at 1100oC in air
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
The dataset includes XRD patterns of Sr1.9Fe1.5Mo0.5O6 powder prepared using wet chemistry methods, namely modified Pechini route. The powders were sintered at 1100oC for 12 h in air.
The XRD diffraction patterns of La0.3Sr1.7Al0.1Fe1.5Mo0.5O6 powder calcined at 1100oC in air
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
The dataset includes XRD patterns of La0.3Sr1.7Al0.1Fe1.5Mo0.5O6 powder prepared using wet chemistry methods, namely modified Pechini route. The powders were sintered at 1100oC for 12 h in air.
The XRD diffraction patterns of Sr1.9Fe1.4Ni0.1Mo0.5O6 powder calcined at 1200oC in air
Dane Badawcze
- P. Błaszczak
- B. Bochentyn
The dataset includes XRD patterns of Sr1.9Fe1.4Ni0.1Mo0.5O6 powder prepared using wet chemistry methods, namely modified Pechini route. The powders were sintered at 1200oC for 12 h in air.
The TPO oxidation profile of CeO2/10wt.%Ni without BCD - prereduced
Dane Badawcze
The dataset includes the TPO oxidation profiles of CeO2/10wt.%Ni. The samples of nanoCeO2 impregnated without BCD-assisted precursor solution (betacyclodextrin). The dataset includes oxidation profile of the prereduced sample.
The TPO oxidation profile of CeO2/10wt.%Co without BCD - prereduced
Dane Badawcze
The dataset includes the TPO oxidation profiles of CeO2/10wt.%Co. The samples of nanoCeO2 impregnated without BCD-assisted precursor solution (betacyclodextrin). The dataset includes oxidation profile of the prereduced sample.

wyświetlono 4721 razy

Wyszukiwarka

mgr inż. Patryk Błaszczak

Zatrudnienie

Obszary badawcze

seria: Impact of strontium non-stoichiometry of SrxTi0.3Fe0.7O3-δ liczba: 6

seria: Ceria liczba: 3

seria: DIR-SOFC liczba: 43

seria: Exsolution liczba: 18