Corrosion process monitoring by AFM higher harmonic imaging - Publikacja - MOST Wiedzy


Corrosion process monitoring by AFM higher harmonic imaging


The atomic force microscope (AFM) was invented in 1986 as an alternative to the scanning tunnelling microscope, which cannot be used in studies of non-conductive materials. Today the AFM is a powerful, versatile and fundamental tool for visualizing and studying the morphology of material surfaces. Moreover, additional information for some materials can be recovered by analysing the AFM's higher cantilever modes when the cantilever motion is inharmonic and generates frequency components above the excitation frequency, usually close to the resonance frequency of the lowest oscillation mode. This method has been applied and developed to monitor corrosion processes. The higher-harmonic imaging is especially helpful for sharpening boundaries between objects in heterogeneous samples, which can be used to identify variations in steel structures (e.g. corrosion products, steel heterogeneity). The corrosion products have different chemical structures because they are composed of chemicals other than the original metal base (mainly iron oxides). Thus, their physicochemical properties are different from the primary basis. These structures have edges at which higher harmonics should be more intense because of stronger interference between the tip and the specimen structure there. This means that the AFM's higher-harmonic imaging is an excellent tool for monitoring surficial effects of the corrosion process.


  • 1


  • 1

    Web of Science

  • 1


Pełna treść

pobierz publikację
pobrano 14 razy


Copyright (2017 IOP Publishing Ltd)

Informacje szczegółowe

Publikacja w czasopiśmie
artykuł w czasopiśmie wyróżnionym w JCR
Opublikowano w:
ISSN: 0957-0233
Rok wydania:
Opis bibliograficzny:
Babicz-Kiewlicz S., Zieliński A., Smulko J., Darowicki K.: Corrosion process monitoring by AFM higher harmonic imaging// MEASUREMENT SCIENCE & TECHNOLOGY. -Vol. 28, iss. 11 (2017), s.1-10
Cyfrowy identyfikator dokumentu elektronicznego (otwiera się w nowej karcie) 10.1088/1361-6501/aa844a
Bibliografia: test
  1. Smulko J, Darowicki K and Zielinski A 2006 Evaluation of reinforcement corrosion rate in concrete structures by electrochemical noise measurements Russ. J. Electrochem. 42 546 otwiera się w nowej karcie
  2. Darowicki K, Zielinski A and Kurzydlowski K J 2008 Application of dynamic impedance spectroscopy to atomic force microscopy Sci. Technol. Adv. Material. 9 045006 otwiera się w nowej karcie
  3. Artunow A, Darowicki K and Tobiszewski M T 2013 Electrical mapping of AISI 304 stainless steel subjected to intergranular corrosion performed by means of AFM-LIS in the contact mode Corros. Sci. 71 37 otwiera się w nowej karcie
  4. Binnig G and Quate C F 1996 Surface studies by scanning tunneling microscopy Phys. Rev. Lett. 49 57 otwiera się w nowej karcie
  5. Antoniuk P, Strąkowski M, Pluciński J and Kosmowski B 2012 Non-destructive inspection of anti-corrosion protective coatings using optical coherent tomography Metrol. Meas. Syst. 19 365 otwiera się w nowej karcie
  6. Hoja J and Lentka G 2013 A family of new generation miniaturized impedance analyzers for technical object diagnostics Metrol. Meas. Syst. 20 43 otwiera się w nowej karcie
  7. Ryl J, Bogdanowicz R, Slepski P, Sobaszek M and Darowicki K 2014 Dynamic electrochemical impedance spectroscopy (DEIS) as a tool for analyzing surface oxidation processes on boron-doped diamond electrodes J. Electrochem. Soc. 161 H359 otwiera się w nowej karcie
  8. Babicz S, Smulko J and Zieliński A 2013 Enhancing capabilities of atomic force microscopy by tip motion harmonics analysis Bull. Acad. Pol. Sci. 61 535 otwiera się w nowej karcie
  9. Babicz S, Zieliński A, Smulko J and Darowicki K 2013 A measurement system for nonlinear surface spectroscopy with an atomic force microscope during corrosion process monitoring Pomiary Autom. Kontrola 59 287 otwiera się w nowej karcie
  10. Stark R W and Stark M 2000 Applied Scanning Probe Methods II. NanoScience and Technology (Berlin: Springer) p 1 otwiera się w nowej karcie
  11. Stark R W and Heckl W M 2000 Fourier transformed atomic force microscopy: tapping mode atomic force microscopy beyond the Hookian approximation Surf. Sci. 457 219 otwiera się w nowej karcie
  12. Legleiter J, Park M, Cusick B and Kowalewski T 2006 Scanning probe acceleration microscopy (SPAM) in fluids: mapping mechanical properties of surfaces at the nanoscale Proc. Natl Acad. Sci. USA 103 4813 otwiera się w nowej karcie
  13. Kokawa H, Shimada M and Sato Y 2000 Grain-boundary structure and precipitation in sensitized austenitic stainless steel JOM 52 34 otwiera się w nowej karcie
  14. Preiner J, Tang J, Pastushenko V and Hinterdorfer P 2007 Higher harmonic atomic force microscopy: imaging of biological membranes in liquid Phys. Rev. Lett. 99 046102 otwiera się w nowej karcie
  15. Aydoğdu G H and Aydinol M K 2006 Determination of susceptibility to intergranular corrosion and electrochemical reactivation behaviour of AISI 316L type stainless steel Corros. Sci. 48 3565 otwiera się w nowej karcie
  16. Kokawa H, Shimada M, Michiuchi M, Wang Z J and Sato Y S 2007 Arrest of weld-decay in 304 austenitic stainless steel by twin-induced grain boundary engineering Acta Mater. 54 5401 otwiera się w nowej karcie
  17. Gaudett M A and Scully J R 1993 Distributions of Cr depletion levels in sensitized AISI 304 stainless steel and its implications concerning intergranular corrosion phenomena J. Electr. Soc. 140 3425 otwiera się w nowej karcie
  18. Kelly W K, Iyer R N and Pickering H W 1993 Another grain boundary corrosion process in sensitized stainless steel J. Electr. Soc. 140 3134 otwiera się w nowej karcie
  19. Kerner Z, Horvath A and Nagy G 2007 Comparative electrochemical study of 08H18N10T, AISI 304 and AISI 316L stainless steels Electrochim. Acta 52 7529 otwiera się w nowej karcie
  20. Sahlaoui H, Makhlouf K, Sidhom H and Philibert J 2004 Effects of ageing conditions on the precipitates evolution, chromium depletion and intergranular corrosion susceptibility of AISI 316L: experimental and modeling results Mater. Sci. Eng. A 372 98 otwiera się w nowej karcie
  21. Michiuchi M, Kokawa H, Wang Z J, Sato Y S and Sakai K 2006 Twin-induced grain boundary engineering for 316 austenitic stainless steel Acta Mater. 54 5179 otwiera się w nowej karcie
  22. Lopez N, Cid M and Puiggali M 1997 Application of double loop electrochemical potentiodynamic reactivation test to austenitic and duplex stainless steels Mater. Sci. Eng. A 229 123 otwiera się w nowej karcie
  23. Yanliang H, Kinsella B and Becker T 2008 Sensitisation identification of stainless steel to intergranular stress corrosion cracking by atomic force microscopy Mater. Lett. 62 1863 otwiera się w nowej karcie
  24. Maachi B, Pirri C, Mehdaoui C, Hakiki N E and Bubendorff J L 2011 Atomic force microscopy, scanning Kelvin probe force microscopy and magnetic measurements on thermally oxidized AISI 304 and AISI 316 stainless steels Corros. Sci. 53 984 otwiera się w nowej karcie
  25. Sathirachinda N, Pettersson R and Pan J 2009 Depletion effects at phase boundaries in 2205 duplex stainless steel characterized with SKPFM and TEM/EDS Corros. Sci. 51 1850 otwiera się w nowej karcie
  26. Kreta A, Rodošek M, Slemenik Perše L, Orel B, Gaberšček M and Šurca Vuk A 2016 In situ electrochemical AFM, ex situ IR reflection-absorption and confocal Raman studies of corrosion processes of AA 2024-T3 Corros. Sci. 104 290 otwiera się w nowej karcie
  27. Singh S, Basu S, Poswal A K, Tokas R B and Ghosh S K 2009 Electrochemically controlled pitting corrosion in Ni film: a study of AFM and neutron reflectometry Corros. Sci. 51 575 otwiera się w nowej karcie
  28. Sarvghad-Moghaddam M, Parvizi R, Davoodi A, Haddad-Sabzevar M and Imani A 2014 Establishing a correlation between interfacial microstructures and corrosion initiation sites in Al/Cu joints by SEM-EDS and AFM-SKPFM Corros. Sci. 79 148 otwiera się w nowej karcie
  29. Davoodi A, Pan J, Leygraf C and Norgren S 2007 Integrated AFM and SECM for in situ studies of localized corrosion of Al alloys Electrochim. Acta 52 7697 otwiera się w nowej karcie
  30. Sudesh Wijesinghe T L L and Blackwood D J 2007 Real time pit initiation studies on stainless steels: the effect of sulphide inclusions Corros. Sci. 49 1755 otwiera się w nowej karcie
  31. Martin F A, Bataillon C and Cousty J 2008 In situ AFM detection of pit onset location on a 304L stainless steel Corros. Sci. 50 84 otwiera się w nowej karcie
  32. Williford R E, Windisch C F and Jones R H 2000 In situ observations of the early stages of localized corrosion in Type 304 SS using the electrochemical atomic force microscope Mater. Sci. Eng. A 288 54 otwiera się w nowej karcie
  33. Li J and Meier D J 1998 An AFM study of the properties of passive films on iron surfaces J. Electroanal. Chem. 454 53 otwiera się w nowej karcie
  34. Wang R 2004 An AFM and XPS study of corrosion caused by micro-liquid of dilute sulfuric acid on stainless steel Appl. Surf. Sci. 227 399 otwiera się w nowej karcie
  35. Kiwilszo M and Smulko J 2009 Pitting corrosion characterization by electrochemical noise measurements on asymmetric electrodes J. Solid State Electrochem. 13 1681 otwiera się w nowej karcie
  36. Lütjering G 1998 Influence of processing on microstructure and mechanical properties of (α + β) titanium alloys Mater. Sci. Eng. A 243 32 otwiera się w nowej karcie
  37. Zieliński A, Bogdanowicz R, Ryl J, Burczyk L and Darowicki K 2014 Local impedance imaging of boron-doped polycrystalline diamond thin films Appl. Phys. Lett. 105 131908 otwiera się w nowej karcie
  38. Ryl J, Wysocka J, Jarzynka M, Zielinski A, Orlikowski J and Darowicki K 2014 Effect of native air-formed oxidation on the corrosion behavior of AA 7075 aluminum alloys Corros. Sci. 87 150 otwiera się w nowej karcie
  39. Ryl J, Wysocka J, Slepski P and Darowicki K 2016 Instantaneous impedance monitoring of synergistic effect between cavitation erosion and corrosion processes Electrochim. Acta 203 388 otwiera się w nowej karcie
  40. Ryl J, Wysocka J and Darowicki K 2014 Determination of causes of accelerated local corrosion of austenitic steels in water supply systems Constr. Build. Mater. 64 246 otwiera się w nowej karcie
Politechnika Gdańska

wyświetlono 27 razy

Publikacje, które mogą cię zainteresować

Meta Tagi