Abstrakt
The paper presents an experimental investigation of a silicone based heat exchanger, with passive heat transfer intensification by means of surface enhancement. The main objective of this paper was to experimentally investigate the performance of a heat exchanger module with the enhanced surface. Heat transfer in the test section has been examined and described with precise measurements of thermal and flow conditions. Reported tests were conducted under steady-state conditions for single-phase liquid cooling. Proposed surface modification increases heat flux by over 60%. Gathered data presented, along with analytical solutions and numerical simulation allow the rational design of heat transfer devices.
Cytowania
-
0
CrossRef
-
0
Web of Science
-
1
Scopus
Autorzy (4)
Cytuj jako
Pełna treść
- Wersja publikacji
- Accepted albo Published Version
- Licencja
-
otwiera się w nowej karcie
Słowa kluczowe
Informacje szczegółowe
- Kategoria:
- Publikacja w czasopiśmie
- Typ:
- artykuły w czasopismach recenzowanych i innych wydawnictwach ciągłych
- Opublikowano w:
-
Archives of Thermodynamics
nr 40,
strony 127 - 143,
ISSN: 1231-0956 - Język:
- angielski
- Rok wydania:
- 2019
- Opis bibliograficzny:
- Muszyński T., Andrzejczyk R., Wong Park I., Dorao C.: Heat transfer and pressure drop characteristics of the silicone-based plate heat exchanger// Archives of Thermodynamics. -Vol. 40., iss. 1 (2019), s.127-143
- DOI:
- Cyfrowy identyfikator dokumentu elektronicznego (otwiera się w nowej karcie) 10.24425/ather.2019.128294
- Bibliografia: test
-
- Muszynski T.: Design and experimental investigations of a cylindrical microjet heat exchanger for waste heat recovery systems. Appl. Therm. Eng. 115(2017), 782-792. DOI:10.1016/j.applthermaleng.2017.01.021. otwiera się w nowej karcie
- Kowalczyk C., Rolf R.M., Kowalczyk B., Badyda K.: Mathematical model of combined geat and power plant using GateCycle TM software. J. Power Technol. 95(2015), 183-191.
- Mikielewicz D., Jakubowska B.: Prediction of flow boiling heat transfer coeffi- cient for carbon dioxide in minichannels and conventional channels. Arch. Thermo- dyn. 37(2016), 2, 89-106. DOI:10.1515/aoter-2016-0014. otwiera się w nowej karcie
- Mikielewicz D., Jakubowska B.: Calculation method for flow boiling and flow condensation of R134a and R1234yf in conventional and small diameter channels. Polish Marit. Res. 24(2017), 141-148. DOI:10.1515/pomr-2017-0032. otwiera się w nowej karcie
- Cho E.S., Choi J.W., Yoon J.S., Kim M.S.: Experimental study on microchannel heat sinks considering mass flow distribution with non-uniform heat flux conditions. Int. J. Heat Mass Tran. 53(2010), 9, 2159-2168. DOI:10.1016/j.ijheatmasstransfer.2009.12.026. otwiera się w nowej karcie
- Muszynski T., Mikielewicz D.: Structural optimization of microjet array cooling system. Appl. Therm. Eng. 123 (2017), 103-110. DOI:10.1016/j.applthermaleng.2017.05.082. otwiera się w nowej karcie
- Muszynski T., Andrzejczyk R.: Heat transfer characteristics of hybrid mi- crojet -microchannel cooling module. Appl. Therm. Eng. 93(2016), 1360-1366. DOI:10.1016/j.applthermaleng.2015.08.085. otwiera się w nowej karcie
- Muszynski T., Mikielewicz D.: Comparison of heat transfer characteristics in surface cooling with boiling microjets of water, ethanol and HFE7100. Appl. Therm. Eng. 93(2016), 1403-1409. DOI:10.1016/j.applthermaleng.2015.08.107. otwiera się w nowej karcie
- Muszynski T., Andrzejczyk R., Dorao C.A.: Detailed experimental investi- gations on frictional pressure drop of R134a during flow boiling in 5 mm diame- ter channel: The influence of acceleration pressure drop component. Int. J. Refrig. 82(2017). DOI:10.1016/j.ijrefrig.2017.05.029. otwiera się w nowej karcie
- Muszynski T., Andrzejczyk R., Dorao C.A.: Investigations on mixture prepa- ration for two phase adiabatic pressure drop of R134a flowing in 5 mm diameter channel. Arch. Thermodyn. 38(2017), 3, 101-118. DOI:10.1515/aoter-2017-0018. otwiera się w nowej karcie
- Motyliński K., Kupecki J.: Modeling the dynamic operation of a small fin plate heat exchanger-parametric analysis. Arch. Thermodyn. 36(2015), 3, 85-103. DOI:10.1515/aoter-2015-0023. otwiera się w nowej karcie
- Taler D., Ocłoń P.: Thermal contact resistance in plate fin-and-tube heat ex- changers, determined by experimental data and CFD simulations. Int. J. Therm. Sci. 84(2014), 309-322. DOI:10.1016/j.ijthermalsci.2014.06.001. otwiera się w nowej karcie
- Zhu Y., Hu Z., Zhou Y., Jiang L., Yu L.: Discussion of the internal heat ex- changer's effect on the organic rankine cycle. Appl. Therm. Eng. 75(2015), 334-343. DOI:10.1016/j.applthermaleng.2014.10.037. otwiera się w nowej karcie
- Wang Q., Zeng M., Ma T., Du X., Yang J.: Recent development and appli- cation of several high-efficiency surface heat exchangers for energy conversion and utilization. Appl. Energy. 135(2014), 748-777. otwiera się w nowej karcie
- Bustamante J.G., Rattner A.S., Garimella S.: Achieving near-water-cooled power plant performance with air-cooled condensers. Appl. Therm. Eng. 105(2016), 362-371. DOI:10.1016/j.applthermaleng.2015.05.065. otwiera się w nowej karcie
- Kupecki J., Badyda K.: Mathematical model of a plate fin heat exchanger oper- ating under solid oxide fuel cell working conditions. Arch. Thermodyn. 34(2013), 4, 3-21. DOI:10.2478/aoter-2013-0026. otwiera się w nowej karcie
- Muszynski T., Andrzejczyk R.: Applicability of arrays of microjet heat transfer correlations to design compact heat exchangers. Appl. Therm. Eng. 100(2016), 105- 113. DOI:10.1016/j.applthermaleng.2016.01.120 otwiera się w nowej karcie
- Fratczak M., Nowak P., Czeczot J., Metzger M.: Simplified dynamical input- output modeling of plate heat exchangers -case study. Appl. Therm. Eng. 98(2016), 880-893. DOI:10.1016/j.applthermaleng.2016.01.004. otwiera się w nowej karcie
- Trojanowski R., Butcher T., Worek M., Wei G.: Polymer heat exchanger design for condensing boiler applications. Appl. Therm. Eng. 103(2016), 150-158. DOI:10.1016/j.applthermaleng.2016.03.004. otwiera się w nowej karcie
- Muszynski T., Koziel S.M.: Parametric study of fluid flow and heat transfer over louvered fins of air heat pump evaporator. Arch. Thermodyn. 37(2016), 3, 45-62. DOI:10.1515/aoter-2016-0019. otwiera się w nowej karcie
- Andrzejczyk R., Muszynski T.: Performance analyses of helical coil heat ex- changers. The effect of external coil surface modification on heat exchanger effec- tiveness. Arch. Thermodyn. 37(2016) 4, 137-159. DOI:10.1515/aoter-2016-0032. otwiera się w nowej karcie
- National Instruments Coorporation LabVIEW User Manual. Ni.com (2013). otwiera się w nowej karcie
- Taylor B.N., Kuyatt C.E.: Guidelines for evaluating and expressing the uncertainty of NIST measurement results. NIST Tech. Note. 1297(1994), 20. DOI:10.6028/NIST.TN.1900. otwiera się w nowej karcie
- Jansen H., de Boer M., Legtenberg R., Elwenspoek M.: The black silicon method: a universal method for determining the parameter setting of a fluorine-based reactive ion etcher in deep silicon trench etching with profile control. J. Micromech. Microeng. 5(1995), 5, 115. DOI:10.1088/0960-1317/5/2/015. otwiera się w nowej karcie
- Park I.W., Fernandino M., Dorao C.A.: Wetting state transitions over hierarchical conical microstructures. Adv. Mater. Interfaces. 5(2018) 1701039. DOI:10.1002/admi.201701039. otwiera się w nowej karcie
- Weryfikacja:
- Politechnika Gdańska
wyświetlono 135 razy