Wyszukiwarka
Nie znaleźliśmy wyników w zadanych kryteriach!
Ale mamy wyniki w innych katalogach.Filtry
wszystkich: 6117
-
Katalog
- Publikacje 5194 wyników po odfiltrowaniu
- Czasopisma 101 wyników po odfiltrowaniu
- Konferencje 8 wyników po odfiltrowaniu
- Osoby 110 wyników po odfiltrowaniu
- Projekty 3 wyników po odfiltrowaniu
- Kursy Online 88 wyników po odfiltrowaniu
- Wydarzenia 3 wyników po odfiltrowaniu
- Dane Badawcze 610 wyników po odfiltrowaniu
Wyniki wyszukiwania dla: MILLING PROCESS DYNAMICS
-
Tool Life and Process Dynamics in High Speed Ball End Milling of Hardened Steel
Publikacja -
Effect of the Relative Position of the Face Milling Tool towards the Workpiece on Machined Surface Roughness and Milling Dynamics
Publikacja -
A surveillance of dynamic state of the slender end milling process.
PublikacjaPraca poświącona jest nadzorowaniu drgań wirujących narzędzi w nowoczesnych frezarkach. Polega ono na zastosowaniu sterowania programowego w układach niestacjonarnych. Podejście dotyczy zamkniętego układu obrabiarki, w przypadku którego istotną rolę odgrywają drgania samowzbudne typu chatter. Stąd, sygnałem sterującym jest chwilowa zmiana prędkości obrotowej wrzeciona. Przedmiotem rozważań jest proces frezowania czołowego smukłym...
-
FPGA Based Real Time Simulations of the Face Milling Process
PublikacjaThe article presents a successful implementation of the milling process simulation at the Field-Programmable Gate Array (FPGA). By using FPGA, very rigorous Real-Time (RT) simulation requirements can be met. The response time of the FPGA simulations is significantly reduced, and the time synchronization is better than in a typical RT system implemented in software. The FPGA-based approach is characterized by enormous flexibility...
-
Technological and tribological aspects of milling-burnishing process of complex surfaces
Publikacja -
The clamping selection method to reduce the vibration of large-size workpieces during the face milling process
PublikacjaThe article introduces a method for selecting the best clamping conditions to obtain vibration reduction during milling of large-size workpiece. It is based on experimental modal analysis performed for a set of assumed, fixing conditions of a considered workpiece to identify Frequency Response Functions (FRFs) for each tightening torque of the mounting screws. Simulated plots of periodically changing nominal cutting forces are...
-
A method of predicting the best conditions for large-size workpiece clamping to reduce vibration in the face milling process
PublikacjaThe paper presents an innovative method of solving the problem of vibration suppression during milling of large-size details. It consists in searching for the best conditions for clamping the workpiece based on a rapid modal identification of the dominant natural frequencies only and requires repetitive changes in the tightening torque of the clamping screws. Then, by estimating the minimum work of the cutting forces acting in...
-
Study of the influence of high-energy milling time on the Cu–13Al–4Ni alloy manufactured by powder metallurgy process
Publikacja -
Effect of ball-milling process parameters on mechanical properties of Al/Al2O3/collagen powder composite using statistical approach
Publikacja -
Surface Roughness Evaluation in Thin EN AW-6086-T6 Alloy Plates after Face Milling Process with Different Strategies
PublikacjaLightweight alloys made from aluminium are used to manufacture cars, trains and planes. The main parts most often manufactured from thin sheets requiring the use of milling in the manufacturing process are front panels for control systems, housing parts for electrical and electronic components. As a result of the final phase of the manufacturing process, cold rolling, residual stresses remain in the surface layers, which can influence...