Wyszukiwarka
Filtry
wszystkich: 1196
wybranych: 676
Wyniki wyszukiwania dla: CONSTANT CONDUCTANCE DRIVER
-
Excitation-independent constant conductance isfet driver
PublikacjaA new constant conductance driver for ISFETs sensors has been developed. The proposed circuit maintains the sensor operating point at constant drain-source conductance. The combination of a simple, self-balancing resistance bridge and the subtraction half (or similar fraction) of source-drain voltage from the gate-source voltage provides the independence of output signal from current and voltage drivers instability. The use of...
-
Selection of physiological parameters for optoelectronic system supporting behavioral therapy of autistic children
PublikacjaIn this article the procedure of selection of physiological parameters for optoelectronic system supporting behavioral therapy of autistic children is proposed. Authors designed and conducted an experiment in which a group of 30 health volunteers (16 females and 14 males) were examined. Under controlled conditions people were exposed to a stressful situation caused by the picture or sound (1kHz constant sound, which was gradually...
-
Low cost set-up for supercapacitors parameters evaluation
PublikacjaWe propose a use of a power amplifier in the circuit of voltage to current converter (current driver) for supercapacitor charging/discharging in controlled conditions. The current driver is controlled by DAC output of DAQ board and voltage of DUT is measured and a control loop is realized by software. In the circuit the DC current method of evaluation of capacitance and equivalent series...
-
Low cost set-up for supercapacitors parameters evaluation
PublikacjaSupercapacitors are capable to store relatively high amount of energy comparing to its mass. Growing number of these devices applications requires development of new testing methods. Standard methods of evaluation of supercapacitor parameters, as cycling voltammetry, CV, galvanostatic cycling with potential limitation, GCPL, impedance measurements, require equipment of high cost...
-
Condition-Based Monitoring of DC Motors Performed with Autoencoders
PublikacjaThis paper describes a condition-based monitoring system estimating DC motor degradation with the use of an autoencoder. Two methods of training the autoencoder are evaluated, namely backpropagation and extreme learning machines. The root mean square (RMS) error in the reconstruction of successive fragments of the measured DC motor angular-frequency signal, which is fed to the input of autoencoder, is used to determine the health...
-
The impact of the temperament model on the behavior of an autonomous driver
PublikacjaBecause it is generally believed that the personality and temperament of a human driver influence his/her behavior on the road, the article presents a computational model of the temperament of an autonomous agent - a driver. First, a short review of the four ideas of Galen’s temperament in psychology is presented. Temperament traits are grouped into four other sets, one of which is chosen for implementation in the project of integration...
-
Gate Driver with Overcurrent Protection Circuit for GaN Transistors
PublikacjaThe improvement of the gate driver for GaN transistor is presented in this paper. The proposed topology contains the overcurrent protectionwith the two-stage turning off and independent control of turn on and off time of the GaN transistor. The operation of driver and its application in thehalf-bridge converter are described using both simulation and prototype measurements. The overcurrent protection was tested in Double Pulse...
-
Design and implementation of the driver system for Hamamatsu C12880MA microspectrometer
PublikacjaRecent miniaturization developments in devices for spectroscopy have reduced greatly their costs and increased their availability for a wide range of users and applications. This paper presents the design and implementation of a driver system for a Hamamatsu C12880MA microspectrometer. The system implementation was carried out and compared using two independent microcontroller modules: Arduino Uno and STM32F411RE Nucleo. We assessed...
-
Driver Fatigue and Road Safety on Poland's National Roads
PublikacjaThis paper presents an overview of factors causing driver fatigue as described in the literature. Next, a traffic crash database for 2003–2007 is used to identify the causes, circumstances and consequences of accidents caused by driver fatigue on Poland’s national roads. The results of the study were used to build a model showing the relationship between the concentration of road accidents and casualties, and the time of day. Finally,...
-
Photovoltaic Maximum Power Point Technique based on Incremental Conductance (INCON) control algorithm
PublikacjaMaximum output power status can significantly improve the deployment rate of solar energy system. In order to get the maximum power output, issue of tracking maximum power point (MPP), reduced harmonics around MPP and improve efficiency of the solar power energy system, this paper presents the improved maximum power point tracking (MPPT) control...
-
Autonomous Driver Based on an Intelligent System of Decision-Making
PublikacjaThe paper presents and discusses a system (xDriver) which uses an Intelligent System of Decision-making (ISD) for the task of car driving. The principal subject is the implementation, simulation and testing of the ISD system described earlier in our publications for the task of autonomous driving. The design of the whole ISD system is a result of a thorough modelling of human psychology based on an extensive literature study. Concepts...
-
Defect-induced conductance oscillations in short atomic chains
Publikacja -
Emotions Embodied in the SVC of an Autonomous Driver System
PublikacjaA concept of embodied intelligence (EI) is considered. None of such implementations can be fully identified with artificial intelligence. Projects that dare to approach AI and EI should be based on both the AI concepts (symbolic and sub-symbolic), in solving real problems of perception and decision-making. Therefore, the EI, in this paper, is understood as a methodology that uses all available resources and algorithms from the...
-
Psychosocial risks associated with the profession of train driver
PublikacjaExcellent competencies as well as a good physical and mental health are required in train drivers’ profession. Despite the changes in the structure of employment the train drivers above 46 years and job tenure longer than 30 years are the largest group. The generation gap is becoming more pronounced, and its fulfilment will not be easy. It is related not only to training of new personnel but also promotion of healthy work environment...
-
Constant vs. Variable Efficiency of Electric Drive in Train Run Simulations
PublikacjaTrain run simulations, which focus on various power- and energy-oriented aspects, should reflect the losses in the electric powertrain. In general, the powertrain efficiency varies with respect to load and speed. Including this relation in simulation requires knowledge about detailed drivetrain parameters, which are often unavailable. This paper verifies the possibility to approximate the drivetrain efficiency in train run simulations...
-
An analytic approach to the conductance and I-V characteristics of polymeric chains
Publikacja -
Negative impact of constant RPM control strategy on ship NOx emission in waves
PublikacjaIn severe wave conditions, the ship propulsion system is loaded with high fluctuations due to external disturbances. The highly fluctuating loads enforce radical changes in the main engine torque, which in turn demands variation of the fuel rate injected into the cylinders if a constant rotational speed strategy is applied. Therefore, the temperature of gases varies to a large extent during the combustion process in the cylinders....
-
Driver Fatigue and Road Safety on Poland’s National Roads
Publikacja -
Contribution of PsbS Function and Stomatal Conductance to Foliar Temperature in Higher Plants
Publikacja -
Constant-Factor Approximation Algorithm for Binary Search in Trees with Monotonic Query Times
PublikacjaWe consider a generalization of binary search in linear orders to the domain of weighted trees. The goal is to design an adaptive search strategy whose aim is to locate an unknown target vertex of a given tree. Each query to a vertex v incurs a non-negative cost ω(v) (that can be interpreted as the duration of the query) and returns a feedback that either v is the target or the edge incident to v is given that is on the path towards...
-
Psychophysiological strategies for enhancing performance through imagery – skin conductance level analysis in guided vs. self-produced imagery
PublikacjaAthletes need to achieve their optimal level of arousal for peak performance. Visualization or mental rehearsal (i.e., Imagery) often helps to obtain an appropriate level of activation, which can be detected by monitoring Skin Conductance Level (SCL). However, different types of imagery could elicit different amount of physiological arousal. Therefore, this study aims: (1) to investigate differences in SCL associated with two instructional...
-
Multidimentional innovation as a driver of economic development. European country study
PublikacjaArtykuł stanowi analizę innowacyjności w ujęciu wielowymiarowym, jako jednym z głównych czynników poziomu rozwoju gospodarczego kraju. Autorzy wykorzystują Summary Innovation Index jako miary wielowymiarowje innowacyjnosci kraju. Zdefiniowane zostaje pojęcie luki innowacyjnej.
-
Torsion of restrained thin-walled bars of open constant bisymmetric cross-section
PublikacjaElastic and geometric stiffness matrices were derived using Castigliano's first theorem, for the case of torsion of restrained thin-walled bars of open constant bisymmetric cross-section. Functions which describe the angles of torsion were adopted from the solutions of thedifferential equation for restrained torsion. The exact solutions were simplified by expanding them in a power series. Numerical examples were taken from Kujawa...
-
Bifurcation of equilibrium forms of a gas column rotating with constant speed around its axis of symmetry
PublikacjaWe will be concerned with the problem of deformation of the lateral surface of a column that rotates with constant speed around its axis of symmetry. The column is filled by a gas and our goal is to investigate the deformation of the lateral surface depending on the pressure of the gas.
-
The dying medium temperature impact on the final moisture content of pine wood at constant drying time
PublikacjaThe results of final moisture content of pine wood (Pinus sylvestris L.) after drying process are presented. The wood in the experiments was taken from the northern part of Pomeranian region in Poland. The drying process was performed in the experimental chamber equipped with the micro-jet heat exchanger. The air at temperatures of 40°C, 60°C, 80°C, 100°C and 120°C with relative humidity about 60% and atmospheric pressure was the...
-
Experimental Study of Flow Rate in Hydraulic Satellite Motor with the Rotating Case at a Low Constant Rotational Speed
PublikacjaIn this article was described the methodology for the experimental study of flows in the prototype of a satellite hydraulic motor with a rotating body. The experimental tests of the motor were carried out at a low constant rotational speed in a wide range of pressure drop in this motor. The constant rotational speed of the motor was kept by a worm gear. Based on the test results, the leakage characteristics in the flat gaps of...
-
Effective dielectric constant of two phase dielectric systems
PublikacjaW tym artykule model brick-layer ścianie został rozszerzony na dwufazowe systemy perkolacyjne. Porównano wyniki obliczeń z danymi eksperymentalnymi. Stałe dielektryczne obu faz oraz próg perkolacji pozwala na wyznaczenie efektywnej stałej dielektrycznej systemu dwufazowego.
-
Dimensional Synthesis of Coupled-Resonator Pseudoelliptic Microwave Bandpass Filters with Constant and Dispersive Couplings
PublikacjaIn this paper, we propose a novel technique for the dimensional synthesis of coupled-resonator pseudoelliptic microwave filters with constant and dispersive couplings. The proposed technique is based on numerical simulations of small structures, involving up to two adjacent resonators, and it accounts for a loading effect from other resonators by replacing them with terminations coupled through appropriately scaled inverters. The...
-
Analiza wzrostu polskiego eksportu na rynku Unii Europejskiej przy użyciu metody Constant Market Share.
PublikacjaArtykuł przedstawia metodę ''constant market share'' jako popularne narzędzie analizy osiągnięć eksportowych kraju lub grupy krajów. Na tym tle zaprezentowano wyniki badań nad przyczynami wzrostu polskiego eksportu towarów na rynki krajów Unii Europejskiej w latach 1992-2002.
-
Self-assembly, stability and conductance of amphotericin B channels: bridging the gap between structure and function
PublikacjaAmphotericin B (AmB), one of the most powerful but also toxic drugs used to treat systemic mycoses, is believed to selectively permeabilize fungal cell membranes to ions in a sterol-dependent manner. Unfortunately, the structure of the biologically active AmB channels has long eluded researchers, obstructing the design of safer alternatives. Here, we investigate the structural and thermodynamic aspects of channel formation, stability,...
-
Standing Waves in One-Dimensional Resonator Contaning an Ideal Isothermal Gas Affected by the Constant Mass Force
PublikacjaThe study is devoted to standing acoustic waves in one-dimensional planar resonator which containing an ideal gas. A gas is affected by the constant mass force. Two types of physically justified boundary conditions are considered: zero velocity or zero excess pressure at both boundaries. The variety of nodal and antinodal points is determined. The conclusion is that the nodes of pressure and antinodes of velocity do not longer...
-
Setups for measurement of thermal time constant of bolometers and resistive layers
PublikacjaPrzedstawiono dwa układy do pomiaru termicznej stałej czasowejbolometrów i warstw rezystywnych, umożliwiające pomiar wartości tego parametru w zakresie od pojedynczych milisekund do kilku sekund. Przedstawiono wyniki pomiarów termicznej stałej czasowej wybranych warstw rezystywnych wykonanych w technologii LTCC z niestechiometrycznych tlenków lantanowo-strontowo-żelazowych oraz bolometru cienkowarstwowego wykonanego w tej samej...
-
Dependence of bimolecular recombination rate constant on different experimental parameters
PublikacjaZ otrzymanych wzorów analitycznych oraz przeprowadzonych obliczeń numerycznych wynika, że dla wysokich natężeń pola elektrycznego stała szybkości rekombinacji bimolekularnej jest funkcją zewnętrznego pola elektrycznego oraz koncentracji nośników ładunku. Szczególnie interesujący jest wynik dotyczący obniżania się stałej szybkości rekombinacji wraz ze wzrostem natężenia pola elektrycznego, który różni się zupełnie od przewidywań...
-
Piece-wise constant approximation method of identification of RTS noise
PublikacjaPrzedstawiono nową metodę wydzielania szumów RTS z całkowitych szumów przyrządów półprzewodnikowych. Metoda ta oparta jest na aproksymacji liniowo odcinkowej przebiegu szumowego.Przedstawiono wyniki zastosowania tej metody do wydzielenia dwupoziomowego szumu RTS z szumu przyrządu półprzewodnikowego.
-
Polyurethane glycolysate from industrial waste recycling to develop low dielectric constant, thermally stable materials suitable for the electronics
PublikacjaWe are utilizing a new method to improve the dielectric properties of a conventional polymer using a recycled polymer product. The polyurethane foams are recycled by glycolysis process and the derived material was applied to improve the dielectric properties of the brittle DGEBA epoxy resin. Two main parameters that determine the applicability of the material as a dielectric (the dielectric constant and dielectric loss), were studied...
-
DETERMINING THE TIME CONSTANT USING TWO METHODS AND DEFINING THE THERMOCOUPLE RESPONSE TO SINE EXCITATION OF GAS TEMPERATURE
PublikacjaThis paper describes the two methods of determining the time constant of type K thermocouple, for two construction solutions: the exposed weld and the mantle fillet weld. This is an important parameter indicating the response time of the thermocouple on the recorded signal. The first method consists of determining the value of τ in the way of numerical simulation of heat exchange between the thermocouple and the current of gas...
-
Implementation of constant component filter in measurements of random telegraph signal noise
PublikacjaNoise is generated in all semiconductor devices. The intensity of these fluctuations depends on used elements, manufacturing process, operating conditions and device type. The result noise is a superposition of different kinds of fluctuations like thermal noise, generation-recombination noise, 1/f noise, shot noise and Random Telegraph Signal (RTS) noise. The last one, RTS noise is observed as nonstationary impulse fluctuations....
-
The simultaneous determination of hydrophobicity and dissociation constant by liquid chromatography–mass spectrometry
Publikacja -
Solvent dependency of carbon dioxide Henry's constant in aqueous solutions of choline chloride-ethylene glycol based deep eutectic solvent
PublikacjaThe Henry's constants of carbon dioxide absorbed in aqueous solutions of ethaline (choline chloride-ethylene glycol) were determined for temperatures ranging from 303.15 to 323.15 K based on solubility measurement at CO2 pressure ranging from 0 to 6 bar (0.6 MPa). These studies revealed that the Henry's constant increased with the increase of temperature. Data indicated the highest capacity of CO2 absorption is obtained for ethaline...
-
NUMERICAL SIMULATIONS OF HONING PROCESS OF THIN WALL CYLINDER LINERS, WITH CONSTANT AND WITH VARIABLE THICKNESS OF WALL OF HONED PARTS
PublikacjaNumerical simulations of honing process of thin-wall cylinder liners, with constant and with variable thickness of the wall of honed workpieces can improve and can help to conduct the experimental research of honing process and can improve the honing process. A very valuable research assumption, before performing the numerical analysis of computer simulation of honing process, is the measurement of the real geometry of the honing...
-
Effective dielectric constant of two phase systems: Application to mixed conducting systems
PublikacjaW pracy przedstawiono wyniki badań spektroskopii impedancyjnej systemów dwufazowych oraz ich porównanie z wynikami oczekiwanymi przez różne modele.
-
Single Sensor Hot-Wire Anemometer Based on Thermal Time Constant Estimation
Publikacja -
High-cycle fatique criterion for anisotropic metals under multiaxial constant and periodic loads
PublikacjaPrzedmiotem rozważań jest okresowe naprężenie, którego kartezjańskie składowe są dane w postaci szeregów Fouriera. Dla uwzględnienia wpływu składowych stałych zastosowano zmodyfikowaną formułę Soderberga. Zdefiniowano naprężenie równoważne o synchronicznych składowych i sformułowano kryterium ograniczonej trwałości zmęczeniowej. Kryterium to obejmuje warunki wytrzymałości statycznej i bezpieczeństwa zmęczeniowego z zakresie wysokocyklowym...
-
Fatigue ''safe-life'' criterion for metal elements under multiaxial constant and periodic loads.
PublikacjaRozpatrywane jest okresowe naprężenie którego kartezjańskie składowe są zadane w postaci szeregów Fouriera. Dla uwzględnienia naprężenia średniego wykorzystano uogólnioną formułę Soderberga dla materiałów ciągliwych. Zdefiniowano naprężenie równoważne o synchronicznych składowych i sformułowano kryterium zmęczenia, które obejmuje warunki zarówno wytrzymałości statycznej jak i bezpieczeństwa zmęczeniowego. Kryterium to zawiera stałe...
-
Resistance changes of carbon nanotubes decorated with platinum nanoparticles in the presence of hydrogen at different and constant concentrations
Publikacja -
Closed-form expression for the magnetic shielding constant of the relativistic hydrogenlike atom in an arbitrary discrete energy eigenstate: Application of the Sturmian expansion of the generalized Dirac–Coulomb Green function
PublikacjaWe present analytical derivation of the closed-form expression for the dipole magnetic shielding constant of a Dirac one-electron atom being in an arbitrary discrete energy eigenstate. The external magnetic field, by which the atomic state is perturbed, is assumed to be weak, uniform, and time independent. With respect to the atomic nucleus we assume that it is pointlike, spinless, motionless, and of charge Ze. Calculations are...
-
Driver influence on tyre/road noise generated by vehicle in road traffic.Wpływ kierowcy na hałas generowany przez pojazd w ruchu drogowym.
PublikacjaW pracy omówiono wkływ stylu jazdy kierowcy oraz stanu technicznego wybranych zespołów pojazdu na jego hałas generowany w ruchu drogowym. Wpływ został przeanalizowany w aspekcie takich parametrów, jak: prędkość jazdy, obciążenie kół siłami wzdłużnumi i poprzecznymi, ciśnienie w ogumieniu, obciążenie pionowe kół, zbieżność i inne.
-
The experimental identification of the dynamic coefficients of two hydrodynamic journal bearings operating at constant rotational speed and under nonlinear conditions.
PublikacjaHydrodynamic bearings are commonly used in ship propulsion systems. Typically, they are calculated using numerical or experimental methods. This paper presents an experimental study through which it has been possible to estimate 24 dynamic coefficients of two hydrodynamic slide bearings operating under nonlinear conditions. During the investigation, bearing mass coefficients are identified by means of a newly developed algorithm....
-
Finite element investigations of granular material behaviour during cyclic wall shearing under a constant normal stiffness condition
PublikacjaW artykule przedstawiono wyniki numnerycznej analizy zachowania sie materiałów granulowanych podczas cyklicznego ścinanai wzdłuz szorstkiej ściany z warunkiem stałej sztywności normalnej. Obliczenia wykonano przy zastosowaniu metody elementów skończonych i mikropolarnego nodelu hipopalstycznego. Obliczenia wykonano dla róznych sztywności, początkowych wskaźników porowatości i sredniej średnicy ziarna. Wyniki numeryczne porównano...
-
The interaction of antitumor 1-nitroacridines with DNA in cell-free systems
PublikacjaUzyskano nowe pochodne 1-nitro i 3-nitroakrydyny wykazujące zdolność do specyficznego cięcia DNA w miejscach bezzasadowych. Z użyciem oligonukleotydu z indukowanym miejscem bezzasadowym potwierdzono taką aktywność u obu otrzymanych pochodnych.