Wyniki wyszukiwania dla: model tests
-
Identification of Bodner-Partom Viscoplastic Model Parameters for Some Aluminum Alloys at Elevated Temperature
PublikacjaThe paper presents the identification process of inelastic (viscoplastic) properties for two aluminum alloys at a temperature of 120°C. The material parameters are calculated on the basis of uniaxial tension tests. Twelve tests at elevated temperature for each alloy have been performed—three tests for four different strain rates. The main purpose of the paper is to identify the Bodner-Partom viscoplastic model parameters for two...
-
Experimental tests of lintel hybrid beams
PublikacjaThe results of experimental tests of lintel hybrid beams made of air concrete and prestressed concrete were presented in paper. Blocks of air concrete was a protective element for the construction one. The length of hybrid beams was 3.0 m, while total height 27 cm. It was assumed that hybrid beams will work in the simply-supported scheme (with a 10 cm support) loaded uniformly over the entire length. The object of the tests were...
-
Geosynthetics tests in hydrotechnical structures design
PublikacjaW celu właściwego stosowania w konstrukcjach budowlanych (w tym również hydrotechnicznych)geosyntetyków - zarówno przepuszczalnych (geotekstylia i wyroby pokrewne) jak i nieprzepuszaczalnych (geomembrany i kompozyty uszczelniające), bardzo ważne jest wcześniejsze poddawanie go odpowiednim badaniom, których procedura musi być ściśle powiązana z późniejszym przeznaczeniem geomateriału i uwzględniać warunki, w jakich materiał będzie...
-
A measurement system for children endurance tests
PublikacjaThere are a lot of ethical problems concerning the use of invasive methods for the measurement of a child's body response to physical exercise and physical training. The alternative is are non-invasive methods like ergospirometry or NIRS. The article presents a measurement system dedicated for children endurance tests, composed of a few non-invasive measurement modules, including a temperature measurement module. Temperature is...
-
Strength tests of steel sandwich panel.
PublikacjaPrzedstawiono wyniki badań laboratoryjnych paneli SANDWICH, prowadzonych w Kat. Technol. Okr. i Obiekt. Oceanotech. Wydz. OiO, na konstrukcjach w skali rzeczywistej. Dokonano porównania uzyskanych rezultatów z wynikami prezentowanymi w literaturze.
-
Strength tests of steel sandwich panel
PublikacjaPrzedstawiono wyniki badań laboratoryjnych elementarnego, teowego złącza spawanego laserowo, których celem było określenie pola odkształceń i naprężeń w strefie przyspoinowej. Uzyskane wyniki wskazują na potrzebę bardzo starannego modelowania konstrukcji spawanych laserowo przy obliczeniach MES. W pracy zaprezentowano wyniki badań konstrukcji rzeczywistej pod statycznym obciążeniem ściskającym, które porównano z rezultatami analizy...
-
Strength tests of steel sandwich panel
PublikacjaPrzedstawiono wyniki badań laboratoryjnych elementarnych złączy spawanych laserowo i paneli SANDWICH, prowadzonych w Katedrze Technologii Okrętów i Obiektów Oceanotechnicznych WOiO, na konstrukcjach w skali rzeczywistej. Dokonano analizy zachowania połączenia podczas procesu obciążenia. Przedstawiono wyniki numerycznego zamodelowania własności złącza. Dokonano porównania uzyskanych rezultatów analizy numerycznej z wynikami z badań...
-
Combined numerical and experimental approach to determine numerical model of abdominal scaffold
PublikacjaA proper junction of the prosthesis and the abdominal wall is important in successful hernia repair. The number of tacks should be balanced to assure appropriate mesh fixation and not to induce post-operative pain. Numerical simulations help to find this balance. The study is aimed at creating a proper numerical model of a knitted surgical mesh subjected to boundary conditions and load occurring in the abdominal cavity. Continuous,...
-
CONTROL OF THE WAVES IN A TOWING TANK WITH THE USE OF A BLACK-BOX MODEL
PublikacjaThe paper describes an adaptive control system of the waves, implemented in the Ship Design and Research Centre, CTO S.A. The purpose of generating the waves in the towing tank is the modelling of the environmental conditions during hydrodynamic model tests. The tests are performed on scale models of towed or free running ships, anchored structures like oil rigs or bottommounted structures, e.g. wind turbines. In the towing tank...
-
Model of heat transfer in the stagnation point of rapidly evaporating microjet
PublikacjaThe paper presents investigation in the single water microjet surface cooling producing evaporating film. Reported tests were conducted under steady state conditions. It was proved that the phenomenon is similar to that of pool boiling. Results of experiments were compared with predictions by the model showing a good consistency.
-
Determination of Mathematical Model Parameters of a Medium Frequency Transformer
PublikacjaThe paper presents the results of experimental studies of the medium frequency transformer. The object of the research was a prototype of a single-phase transformer with a core made of ferrite I-core elements and windings made of Litz conductors. The research was carried out to determine the parameters of the transformer's mathematical model. The scope of the tests included determining the magnetic hysteresis loop and measuring...
-
Validation Process for Computational Model of Full-Scale Segment for Design of Composite Footbridge
PublikacjaExperimental tests and numerical simulations of a full-scale segment of a foot and cycle bridge made of polymer composites are presented in the paper. The analysed structure is made of sandwich panels, which consist of glass fibre reinforced polymer (GFRP) multi-layered laminate faces and a PET foam (obtained from recycling) core. The dimensions of the segment cross-section are the same as for the target footbridge; however, span...
-
SIMULATION MODEL OF ASON/GMPLS ARCHITECTURE
PublikacjaGrowing demands of information society concerned with sophisticated applications could be satisfied by ASON/GMPLS architecture comprehended as Automatically Switched Optical Network (ASON) with Generalized Multi-Protocol Label Switching (GMPLS). The ASON/GMPLS proposition represents the future direction of Next Generation Network (NGN) architecture. Therefore considerable work has to be done to examine this solution. In this aspect...
-
A material model of asphalt mixtures based on Monte Carlo simulations
PublikacjaThe paper aims to numerically reflect mineral-asphalt mixture structure by a standard FEM software. Laboratory test results are presented due to bending tests of circular notched elements. The result scatter is relatively high. An attempt was made to form a random aggregate distribution in order to obtain various results corresponding to laboratory tests. The material structure calibration, its homogenization and finite element...
-
Static and dynamic concrete calculations: Breakable aggregates in DEM model
PublikacjaThe paper deals with the calculations of a 3-point bending beam under static and dynamic loads. The real microstructure was obtained from laboratory tests using micro-tomography images. The quasi-static results were compared directly with experimental data at both macro and micro levels. Subsequently, higher strain rates were applied to investigate dynamic effects. The study focused on the influence of dynamic loading on the macroscopic...
-
Tensile curve of E grade steel for shipbuilding
Dane BadawczeIn the shipbuilding industry, the risk of brittle fractures developing in constructions is limited by employing certified materials of specific impact strength, determined using the Charpy method (for a given design temperature) and by exercising control over the welding processes (technology qualification, supervision of production, tests of non-destructive...
-
Small Vessel with Inboard Engine Retrofitting Concepts; Real Boat Tests, Laboratory Hybrid Drive Tests and Theoretical Studies
PublikacjaThe development of modern technologies and their increasing availability, as well as the falling costs of highly ecient propulsion systems and power sources, have resulted in electric or hybrid propulsions systems’ growing popularity for use on watercraft. Presented in the paper are design and lab tests of a prototype parallel hybrid propulsion system. It describes a concept of retrofitting a conventionally powered nine meter-long...
-
Bimodal deep learning model for subjectively enhanced emotion classification in films
PublikacjaThis research delves into the concept of color grading in film, focusing on how color influences the emotional response of the audience. The study commenced by recalling state-of-the-art works that process audio-video signals and associated emotions by machine learning. Then, assumptions of subjective tests for refining and validating an emotion model for assigning specific emotional labels to selected film excerpts were presented....
-
Reverberation chamber in emc tests of naval systems
PublikacjaPaper covers the techniques of emission and immunity testing to the electromagnetic field in reverberation chamber. The procedure of he chamber calibration and field homogeneity assessment were covered. The naval forces' product as selected as an example for discussing the testing procedure in the chamber. The paper's summary gives the assortment of methodology in radiation emission testing and immunity to the electromagnetic field...
-
Polish experience of dynamic tests for bored piles
PublikacjaPrzedstawiono zastosowanie badań dynamicznych, DLT, do oceny nośności wierconych pali wielkośrednicowych.Na podstawie badań terenowych, dla dwóch obiektów mostowych, wykonano badania dynamiczne (DLT) oraz korelacyjne badania statyczne (ASPLT). Określono pełną krzywą osiadania. Uzyskano dobrą zgodność krzywych obciążenie - osiadanie dla zakresu obciążeń roboczych.
-
Laboratory tests of medium voltage switchgear isolators
Publikacja -
Size effect in centrifuge cone penetration tests
PublikacjaOkreślenie efektu skali w badaniu wciskania stożka w zagęszczonych piaskach kwarcowych na podstawie badań modelowych w wirówce geotechnicznej. Badania przeprowadzono na dwóch piaskach kwarcowych przy przyśpieszeniach od 30g do 100g. Analizowano efekt skali związany ze stosunkiem średnicy modelu (mini-stożka) do średniej średnicy ziaren oraz wpływem poziomu naprężenia na opór stożka. Wpływ poziomu naprężenia powoduje powstanie geometrycznego...
-
Experimental tests of reinforced concrete deep-beams
PublikacjaThe paper presents results of experimental research of the reinforced concrete deep beam with a spatial arrangement. Tested structural elements consist of the cantilever deep beam loaded on the height and transverse deep beam with hanging on it another one. The analysis includes crack morphology, effort of steel and load distribution. The article verified effectiveness of two different kind of reinforcement in both tested deep...
-
Evaluation of Lightning Protection Earthings by Impulse Tests
PublikacjaW artykule zamieszczono opis nowej procedury pomiaru uziemień odgromowych metodą udarową. Zgodnie z propozycję podczas testu udarowego można pomierzyć nie tylko impedancję udarową uziemienia, ale także ocenić jego rezystancję oraz współczynnik udaru. Wynik takiego badania uwzględnia tylko tę część uziomu, którą określa się jako jego długość efektywną.
-
Loudness Scaling Tests in Hearing Problems Detection
PublikacjaThe number of people using portable audio players has increased significantly over the recent years. This implies the rise in the number of people having hearing loss problems. Therefore, there is a need to find appropriate procedures that simplify the process of the hearing problem detection. Investigations performed show that audiometric tests may not be sufficient to assess hearing in young people. Contrarily, the obtained results...
-
In Situ Verification of Numerical Model of Water Hammer in Slurries
PublikacjaThis paper presents a numerical model of transient flow in a pressure slurry pipeline network with verification based on in situ measurements. The model, primarily verified in laboratory conditions, has been extended and applied to the case of a large and complex slurry pipeline network in Poland. In the model, the equivalent density concept was applied. In situ experiments were performed for various unsteady flow episodes, caused by...
-
Laboratory Determination of Burger's Model Parameters for Visco-elastic Analysis of Road Pavement Materials
PublikacjaBurger's Model is one of those models that describes performance of asphalt mixtures. Its parameters can be used in road construction analysis based on visco-elastic properties in wide variety of temperatures using dedicated programs (e.g. Veroad) or in Finite Element Method (FEM). Parameters of Burger's Model can be used for example in prediction of low temperature cracking in low winter temperatures or permanent deformation...
-
Experimental determination of dynamic properties of cylindrical steel tank model filled with liquid
PublikacjaIn technical branches, such as chemical or petroleum industries, cylindrical steel tanks are essential structures used for storage of liquid products. Any failure might have disastrous consequences, therefore their safety and reliability is essential. The aim of the present paper is to show the results of the experimental study which has been conducted on a scaled model of a real tank used in Poland. The investigation was carried...
-
Numerical Estimation of Hull Hydrodynamic Derivatives in Ship Maneuvering Prediction
PublikacjaPrediction of the maneuvering characteristics of the ship at the design stage can be done by means of model tests, computational simulations or a combination of both. The model tests can be realized as direct simulation of the standard maneuvers with the free running model, which gives the most accurate results, but is also the least affordable as it requires very large tank or natural lake, as well as complex equipment of the...
-
OBTAINING FLUID FLOW PATTERN FOR TURBINE STAGE WITH NEURAL MODEL.
PublikacjaIn the paper possibility of applying neural model to obtaining patterns of proper operation for fluid flow in turbine stage for fluid-flow diagnostics is discussed. Main differences between Computational Fluid Dynamics (CFD) solvers and neural model is given, also limitations and advantages of both are considered. Time of calculations of both methods was given, also possibilities of shortening that time with preserving the accuracy...
-
ORF Approximation in Numerical Analysis of Fractional Point Kinetics and Heat Exchange Model of Nuclear Reactor
PublikacjaThis paper presents results concerning numerical solutions of the fractional point kinetics (FPK) and heat exchange (HE) model for a nuclear reactor. The model consists of a nonlinear system of fractional and ordinary differential equations. Two methods to solve the model are compared. The first one applies Oustaloup Recursive Filter (ORF) and the second one applies Refined Oustaloup Recursive Filter (RORF). Simulation tests have...
-
ORF Approximation in Numerical Analysis of Fractional Point Kinetics and Heat Exchange Model of Nuclear Reactor
PublikacjaThis paper presents results concerning numerical solutions of the fractional point kinetics (FPK) and heat exchange (HE) model for a nuclear reactor. The model consists of a nonlinear system of fractional and ordinary differential equations. Two methods to solve the model are compared. The first one applies Oustaloup Recursive Filter (ORF) and the second one applies Refined Oustaloup Recursive Filter (RORF). Simulation tests have...
-
Dynamic Tests and Technical Monitoring of a Novel Sandwich Footbridge
PublikacjaA novel sandwich composite footbridge is described in this paper, for the first time after it has been put into operation over the Radunia River in the Pruszcz Gdański municipality. This paper presents results of dynamic tests and describes technical monitoring of the footbridge. The dynamic tests were conducted to estimate pedestrian comfort and were compared with the ones from numerical simulations made in the environment of...
-
CFD Simulations and Tests of a Prototype Flow Control Valve
PublikacjaIn this paper a prototype of a flow control valve is described and numerically simulated. The flow control valve is used in hydraulic systems to maintain constant fluid flow despite changing loads of a receiver. The standard construction of this type of valves is modified mainly by eliminating the spring. The prototype consists the hydrostatically unloaded throttle valve and pressure ratio valve substituting pressure difference...
-
Experimental tests of water lubricated marine rubber bearing
PublikacjaW referacie przedstawiono stosowane obecnie rodzaje łożysk gumowych smarowanych wodą. Omówiono ich zalety i wady.W drugiej części pracy przedstawiono wyniki badań eksperymantalnych typowego okrętowego łożyska gumowego. Uzyskane rezultaty porównano z wynikami badań łożysk z polimerową panwią.
-
Estimation of pile bearing capacity by dynamic and static tests
PublikacjaBadania dynamiczne, szczególnie dla pali wbijanych, w budownictwie hydrotechnicznym stają się coraz bardziej popularne. Badania, poparte formalnie zapisami zawartymi w Eurokodzie 7, wykorzystywane w badaniach ''na wodzie'' i ''na lądzie'' są szybkie i ekonomiczne. Przedstawiono serię badań dla gruntów uwarstwionych dla pali prefabrykowanych żelbetowych, wbijanych stalowych pali rurowych oraz pali Vibro-Fundex. Badania dynamiczne...
-
Physiological tests on firefighters whilst using protective clothing
Publikacja -
Porosimetric, Thermal and Strength Tests of Aerated and Nonaerated Concretes
Publikacja -
Tests of a Steam Piston Engine Under Supercritical Conditions
Publikacja -
Penetration resistance of Lubiatowo sand in calibration chamber tests
PublikacjaAnaliza oporu na wciskanie na stożku sondy statycznej wciskanej na podstawie badań modelowych w komorze kalibracyjnej z kontrolą naprężeń bocznych. Przeprowadzono badania z zastosowaniem standardowej końcówki CPT, dylatometru DMT, mini-stożka CPT oraz pali modelowych o różnej średnicy. Badania wykonano na piasku modelowym z plaży w Lubiatowie w stanie średnio zagęszczonym i zagęszczonym w szerokim zakresie składowej pionowej naprężenia....
-
Dynamic load tests of piles in non-cohesive soils.
PublikacjaThe results of investigations of various types of piles, the analysis of dynamic tests carried out recently in Poland and the correlations between the results of dynamic and static tests of piles are presented. Przedstawiono wyniki badań nośności różnych rodzajów pali, analizę badań dynamicznych wykonanych w Polsce w ostatnich latach oraz korelacje pomiędzy wynikami badań statycznych i dynamicznych.
-
Thermo-mechanic tests using 3d printed elements
Publikacja -
Experimental tests for the determination of mechanical properties of PVC foil
PublikacjaThe paper presents an application of the PVC film in civil engineering. Mechanical behaviour of the PVC film applied for suspended ceilings, in the form of a stretch ceiling is investigated under uniaxial and biaxial tensile tests. The study is focused on the determination of mechanical properties from experimental data (uniaxial and biaxial tensile tests). The uniaxial cyclic tests are performed in order to observe a variation...
-
Experimental tests of steel double-type balcony connections
PublikacjaThe paper presents analysis and results of experimental tests of full scale prefabricated balcony sets with dimensions (width × length × height): 2.0 m × 2.78 m × 0.186 m (in slope to 0.17 m). The sets consists of reinforced concrete slabs (balcony and ceiling) connected with each other by double-type balcony connections. The paper analyses the impact of variable parameters on the load carry capacity of elements. Additionally...
-
Suitableness of SLM Manufactured Turbine Blade for Aerodynamical Tests
PublikacjasettingsOrder Article Reprints Open AccessArticle Suitableness of SLM Manufactured Turbine Blade for Aerodynamical Tests by Janusz Telega 1,*ORCID,Piotr Kaczynski 1ORCID,Małgorzata A. Śmiałek 2ORCID,Piotr Pawlowski 3ORCID andRyszard Szwaba 1ORCID 1 Institute of Fluid Flow Machinery Polish Academy of Sciences (IMP PAN), Fiszera 14, 80-231 Gdansk, Poland 2 Faculty of Mechanical Engineering and Ship Technology, Institute of Naval...
-
Truss models of RC corbels verified by experimental tests
PublikacjaW pracy przedstawiono wybrane modele kartownicowe krótkich wsporników żelbetowych oraz obliczone na podstawie tych modeli nośności graniczne wsporników na tle wyników uzyskanych w badaniach eksperymentalnych. Przedstawiono także weryfikację metody ścinania-tarcia wg wytycznych normy amerykańskiej. Dokonano obliczeń częściowych współczynników bezpieczeństwa, uwzględniających niepewność rozważanych modeli. Stwierdzono, ze modele...
-
Electromagnetic compatibility tests of warship antitorpedo jamming system
PublikacjaW artykule przedstawiono zagadnienie interferencji elektromagnetycznych na okręcie wojennym spowodowanych pracą antytorpedowego systemu zakłócającego. W warunkach laboratoryjnych, dla wybranej konfiguracji systemu, zostały przeprowadzone badania kompatybilnościowe i na podstawie otrzymanych rezultatów zostały sformułowane wnioski praktyczne.
-
Comparative investigation of lubricant properties in friction and wear tests
PublikacjaOpisano porównawcze badania obciążenia zacierania na tribometrze PT3, obciążenia zespawania na aparacie czterokulowym i zużycia frettingowego na stanowisku FRET3, sześciu olejów smarowych i sześciu smarów plastycznych. Próbki do badań na stanowiskach PT3 i FRET3 wykonane były ze stali 35.
-
Static puncture tests of geotextiles and geotextile - related prodcts
PublikacjaW artykule omówiono dwa rodzaje przebicia statycznego geotekstyliów i wyrobów pokrewnych: standardowe badanie CBR zgodnie z normą EN ISO 12236 i nowe metody opracowywane przez CEN TC 189 w ramach projektu normy PrEN 189066. Procedury wykonywania badań są podobne, różnią się: tłokiem obciążającym, metodą podparcia materiału, wypełnieniem cylindra oraz zastosowanym materiałem geosyntetycznym.
-
Manoeuvring forces on azimuthing podded propulsor model
PublikacjaThis paper presents the preliminary part of comprehensive manoeuvring open- water tests of a gas carrier model. The paper focuses on open water experiments with an azimuthing podded propulsor. The test program was carried out in the cavitation tunnel and the large towing tank of Ship Hydromechanics Division, Ship Design and Research Centre, Gdańsk. The pod was tested as a pushing unit with a 161.3 mm diameter propeller. Steering...