Wyszukiwarka
Wyniki wyszukiwania dla: SHIP DYNAMICS
-
Problems of Determination of Welding Angular Distortions of T-fillet Joints in Ship Hull Structures
PublikacjaShip hull structure elements are in majority joined by welding. Welding distortions can cause a lot of problems during the manufacturing process. In the literature it is proposed wide spectrum of suggestions for a correct estimation of welding deformation in particular angular deformation in the fillet welded T joint. In the work verification of selected methods is proposed basing upon of the results of the laboratory measurements....
-
Design of Inner Gate for CRIST Shipyard Dry Dock
PublikacjaThe paper deals with a removable steel inner gate which was designed to separate two parts of a dry dock of about 70 m in width and 380 m in length. The gate allows for independent assembly of ship structures in two separated parts of the dock. The fore part of the dock can be flooded while the after part is dry. Tthe gate was designed by IDEK Company Ltd in 2011 and it was soon constructed and used by CRIST Shipyard in Gdynia.
-
Digital Control System of the Wavemaker in the Towing Tank
PublikacjaThe paper describes a digital control system of the rigid flap wavemaker in a towing tank in CTO S.A. Ship Design and Research Centre. The control system is based on an 8-bit AVR microcontroller and consists of two cascading PID controllers. The digital system replaced the previous analogue system from 1974 and has been integrated with the existing sensors and actuators of the wavemaker. The new control system allows to obtain...
-
OPERATION OF TWO-SHAFT GAS TURBINE IN THE RANGE OF OPEN ANTI-SURGE VALVE
PublikacjaThis paper presents experimental tests of full-scale two-shaft gas turbine in the range of open anti-surge valve (ASV). The tests were carried out in a laboratory gas- turbine test stand belonging to Department of Automation and Power Engineering , Faculty of Ocean Engineering and Ship Technology , Gdańsk University of Technology. The tests covered the start-up and low load operation of the turbine set in the range of open...
-
A novel approach to energy safety improvement in the marine power plants with active power surge compensator
PublikacjaPaper raises a point of power surges and theirs adverse effects in the marine power plants. The article explains a source of surges appearance, and presents measurements carried out on a modern ship. It discusses effects of dynamic power transients on the ship’s energy safety. Finally it proposes, a novel approach for power surge elimination, based on medium voltage active conditioner. As well as it propose the topology and control...
-
Virtual reality as a tool for development and simulation. Research projects and experience of the Gdańsk University of Technology
PublikacjaBy supporting the human imagination, virtual reality technology can be applied in almost every human activity. This is evidenced by the cooperation of the Immersive 3D Visualization Lab with specialists representing such different professions from architects and artists, astronomers and chemists, through historians and museologists, criminologists and military educators, mechanical and ship engineers, up to physicians and psychologists....
-
AN ENERGY APPROACH TO THE FATIGUE LIFE OF SHIP PROPULSION SYSTEMS
PublikacjaThe conducted research investigations aimed to carry out an identification of the constructional materials fatigue state of the ship propulsions’ rotational mechanical units for diagnostic purposes. The fatigue cracks of the elements transmitting mechanical energy streams from the propulsion engines to the ship propellers or to the generators of the ship’s electric power station stand for a primary reason for the secondary, usually...
-
Evaluation of Response Amplitude Operator of Ship Roll Motions Based on the Experiments in White Noise Waves
PublikacjaEvaluation of the response amplitude operator (RAO) function for ship wave frequency motions by means of scale model tests in regular waves is a standard procedure conducted by hydrodynamic model testing institutions. The resulting RAO function allows for evaluating sufficiently reliable seakeeping predictions for low to moderate sea states. However, for standard hull forms, correct prediction of roll motion in irregular wave (and...
-
UUV and AUV Vehicles as the autonomous systems for naval applications
PublikacjaThere is a growing pressure to investigate how to design and build the unmanned underwater vehicles of different types which are devoted towards performing many tasks under the water surface according to the data missions. During the recent years the Department of Ship Design and Subsea Robotics, Faculty of Ocean Engineering and Ship Technology, Gdansk University of Technology designed and built a few types of unmanned underwater...
-
Minimization of a ship's magnetic signature under external field conditions using a multi-dipole model
PublikacjaThe paper addresses the innovative issue of minimizing the ship's magnetic signature under any external field conditions, i.e., for arbitrary values of ambient field modulus and magnetic inclination. Varying values of the external field, depending on the current geographical location, affect only the induced part of ship's magnetization. A practical problem in minimizing the ship signature is separating permanent magnetization...
-
Evolutionary Sets of Safe Ship Trajectories: simulation results
PublikacjaThe Evolutionary Sets of Safe Ship Trajectories is a method solving multi-ship encounter situations. For given positions and motion parameters the method finds a near optimal set of safe trajectories of all ships involved in an encounter. The paper briefly presents foundations of the method and focuses on simulation results for selected test cases based on the Baltic Basin. The computer simulations cover both open waters and restricted...
-
Tracking of the broadband source of the underwater noise in the very shallow water conditions
PublikacjaThe paper contains the result s, both theoretical and experimental , connected with the tracking of the underwater noise source as small ships, pontoon , diver and so on. The pro blem of security in the shallow water area is the challenge for underwater acousticians. In this paper there is take n into account the detection of the sources that move on the surface of the sea or underwater in shallow...
-
Determining and visualizing safe motion parameters of a ship navigating in severe weather conditions
PublikacjaThe paper presents a method of determining, organizing and displaying ship collision avoidance information, which is based on the Collision Threat Parameters Area (CTPA) technique. The method makes it possible to visualize navigational threats as well as possible collision avoidance manoeuvres. The solution is focused on supporting navigation in severe weather conditions. Normally collision avoidance decisions are made taking into...
-
Full-scale CFD simulations for the determination of ship resistance as a rational, alternative method to towing tank experiments
PublikacjaResults of ship resistance predictions obtained from towing tank experiments are affected by the method used to extrapolate from a model scale to a ship scale. Selection of method to determine a form factor is subjective and the extrapolation method is accurate for typical hull forms. For innovative hull forms the proper method for calculating the form factor is questionable. Moreover, the influence of the extrapolation method...
-
Pre-swirl energy saving device in marine application
PublikacjaThis paper covers topics of energy saving device (ESD) with application to marine propulsors. The form of ESD, considered in this paper, consists of fixed lifting foils mounted in front of the screw propeller (the pre-swirl stator/guide vanes). An algorithm for designing propulsion systems, consisting of guide vanes and screw propeller, is presented. The proposed method relies on hybrid lifting line (guide vanes)-lifting surface...
-
Generation and Propagation of Nonlinear Waves in a Towing Tank
PublikacjaThe paper presents the results of the research focused on linear and nonlinear wave generation and propagation in a deepwater towing tank equipped with a single flap-type wavemaker of variable draft. The problem of wave generation and propagation has been theoretically formulated and solved by applying an analytical method; linear and nonlinear solutions were obtained. The linear solution has been verified experimentally. The...
-
Towards an analysis framework for operational risk coupling mode: A case from MASS navigating in restricted waters
PublikacjaMaritime Autonomous Surface Ships (MASSs) constitute highly interconnected and tightly coupled multistate systems. Incorporating the coupling effects of both interactions and dependencies is centrally important to ensure navigation safety of MASSs. This paper proposes a framework for examining the coupling effects in the operational modes (OM) of MASSs. Failure Modes (FMs) of MASSs related to interactions with the environment and...
-
The influence of compensate coils on own ship magnetic field
PublikacjaA ferromagnetic object placed in the earth magnetic field causes a local disturbance in this field distribution. The field distribution disturbance is a function of many arguments like the dimensoins and shape of the object, its ferromagnetic properties ande its positon in relation to the earth magnetic field. in order to minimize the influence of this disturbance one places compensate coils on the ship. Some chosen results of...
-
THE POSSIBILITIES OF ESTIMATING THE RELIABILITY OF SHIP PIPELINES’ ELEMENTS INCLUDING DESTRUCTIVE PHENOMENA ACTING ON THEM
PublikacjaIn the article an approach to the problem of estimating reliability data based on physical models is proposed. The possibility of reliability assessment for selected elements of ship pipelines, based on the recognition of the destructive physical phenomena taking place in them, is discussed. To do this, an overview of these phenomena has been made. In addition, a preliminary review of existing measures of destruction of materials...
-
Comparison of selected parametric methods for prediction of inland waterways ship hull resistance in towing tank test
PublikacjaIn the paper selected approximate methods for calculation of inland waterways ship resistance and their verification by towing tests, compared on the example of a small urban ferry, are presented. The test results are made for both the bare hull and the hull with appendages (skeg, azimuthal propeller). Significant differences between results of the theoretical methods and experimental ones, especially in the case of the model with...
-
Solutions of inverter systems in Shore-to-Ship Power supply systems
PublikacjaThe article presents a clearly formulated need for installing S2SP (Shore to Ship Power) systems, in particular Medium Voltage (MV) systems, along with certain solutions of modern inverter systems used in those systems. Requirements and basic configurations of S2SP systems are discussed, focusing in particular on capabilities of the S2SP system with DC distribution busbar. Moreover, on the background of the executing assumptions...
-
Negative impact of constant RPM control strategy on ship NOx emission in waves
PublikacjaIn severe wave conditions, the ship propulsion system is loaded with high fluctuations due to external disturbances. The highly fluctuating loads enforce radical changes in the main engine torque, which in turn demands variation of the fuel rate injected into the cylinders if a constant rotational speed strategy is applied. Therefore, the temperature of gases varies to a large extent during the combustion process in the cylinders....
-
The effect of numerical 2D and 3D FEM element modelling on strain and stress distributions at laser weld notches in steel sandwich type panels
PublikacjaLike other means of transport, merchant ships face the problem of increasing requirements concerning the environment protection, which, among other issues, implies the reduction of fuel consumption by the ship. Here, the conventional approach which consists in making use of higher strength steels to decrease the mass of the ship hull can be complemented by the use of new steel structures of sandwich panel type. However, the lack...
-
Impact of steel grade on a ship colliding with an offshore wind turbine monopile supporting structure
PublikacjaOffshore wind power is experiencing rapid development around the world. The number of installations and their size is growing. Thousands of monopile support structures with diameters of 10 m and weights of 2000 tons will be installed in the coming years. Offshore wind power installations, often located close to the shore and shipping routes, pose a new challenge to ship safety. The study analyses the damages from an accidental...
-
Ship Evolutionary Trajectory Planning Method with Application of Polynomial Interpolation
PublikacjaPaper presents the application of evolutionary algorithms and polynomial interpolation in ship evolutionary trajectory planning method. Evolutionary algorithms allows to find a coIlision free trajectory in real time, while polynomial interpolation allows to model smooth trajectory which keeps continuity of velocity and acceleration values along path. Combination of this two methods allows to find trajectory, which under some assumptions,...
-
PROBLEMS OF EXPERIMENTAL DETERMINATION OF COEFFICIENTS OF THE WEAR OF SHIP PIPING SYSTEMS
PublikacjaThe article presents series of considerations relating to experimental evaluation of the reliability of ship piping systems. The aim of this study is to attempt to answer the following questions: What should be the tested element? How to choose the diameter of the tested item? What should be the result of measurements and calculations? How to measure? How to choose the duration of the test? How to choose the sample size and elaborate...
-
Combined thrust radial bearing of a submarine main shaft – Design and analysis of failure
PublikacjaThis paper presents an analysis of the combined thrust radial bearing of a submarine propulsion shaft. The lubrication system of the bearing is based on a fixed ring. The efficiency of the lubrication system depends on the shaft speed and temperature, which affects oil viscosity. In turn, the thrust bearing load also depends on the rotational speed of the shaft, because as the speed increases, the drag of the ship increases simultaneously,...
-
SAILING ROUTE PLANNING METHOD CONSIDERING VARIOUS USER CATEGORIES
PublikacjaThe article describes the methodology related to determining the multi-criteria routes for sailing ships. Details of sea area discretisation and discretisation of the description of the sailing vessel properties and manoeuvring principles are shown. User requirements were specified (for five different categories of users) and on this basis the criteria for selecting the most suitable shipping route were formulated. The presented...
-
A Generative Approach to Hull Design for a Small Watercraft
PublikacjaIn the field of ocean engineering, the task of spatial hull modelling is one of the most complicated problems in ship design. This study presents a procedure applied as a generative approach to the design problems for the hull geometry of small vessels using elements of concurrent design with multi-criteria optimisation processes. Based upon widely available commercial software, an algorithm for the mathematical formulation of...
-
Ship Dynamic Positioning Based on Nonlinear Model Predictive Control
PublikacjaThe presented work explores the simulation test results of using nonlinear model predictive control algorithm for ship dynamic positioning. In the optimization task, a goal function with a penalty was proposed with a variable prediction step. The results of the proposed control algorithm were compared with backstepping and PID. The effect of estimation accuracy on the control quality with the implemented algorithms was investigated....
-
PREDICTION OF SHIP MOTIONS IN IRREGULAR WAVES BASED ON RESPONSE AMPLITUDE OPERATORS EVALUATED EXPERIMENTALLY IN NOISE WAVES
PublikacjaThe most common methods for predicting ship roll motions in a specified sea state are direct measurements of motions in a representative irregular wave realisation (time domain) or calculations of motions from response amplitude operators (RAOs) in the frequency domain. The result of the first method is valid only for the tested sea state, whilst the second method is more flexible but less accurate. RAO-based predictions are calculated...
-
Marine traffic risk modelling – an innovative approach and a case study
PublikacjaThis paper presents a model to analyse the risk of two common marine accidents: collision and grounding. Attention is focused on oil tankers since they pose the highest environmental risks. A case study in selected areas of the Gulf of Finland in ice-free conditions is presented. The model utilizes a formula for risk calculation that considers both the probability of an unwanted event and its consequences. The model can be decomposed...
-
Equivalent standard manoeuvres for pod-driven ships
PublikacjaProcedures for carrying out the manoeuvring tests presented in International Maritime Organisation (IMO) resolution MSC.137(76) are based on the capabilities of ships with conventional steering-propulsion systems. Therefore they do not correspond to ships with other steering-propulsion devices, like pod drives. IMO is aware of this shortcoming and for ships with non-conventional steering and propulsion system may permit the use...
-
REVIEW OF WEATHER FORECAST SERVICES FOR SHIP ROUTING PURPOSES
PublikacjaWeather data is nowadays used in a variety of navigational and ocean engineering research problems: from the obvious ones like voyage planning and routing of sea-going vessels, through the analysis of stability-related phenomena, to detailed modelling of ships’ manoeuvrability for collision avoidance purposes. Apart from that, weather forecasts are essential for passenger cruises and fishing vessels that want to avoid the risk...
-
Advanced Bayesian study on inland navigational risk of remotely controlled autonomous ship
PublikacjaThe arise of autonomous ships has necessitated the development of new risk assessment techniques and methods. This study proposes a new framework for navigational risk assessment of remotely controlled Maritime Autonomous Surface Ships (MASS). This framework establishes a set of risk influencing factors affecting safety of navigation of a remotely-controlled MASS. Next, model parameters are defined based on the risk factors, and...
-
Quantumness in Diagnostics of Marine Internal Combustion Engines and Other Ship Power Plant Machines
PublikacjaThe article provides proof that the diagnostics of marine internal combustion engines and other ship power plant machines should take into account the randomness and unpredictability of certain events, such as wear, damage, the variations of mechanical and thermal loads, etc., which take place during machine operation. In the article, the energy E, like the other forms (methods) that it can be converted into (heat and work), is...
-
The Niching Mechanism in the Evolutionary Method of Path Planning
PublikacjaThis paper presents the concept of the niching mechanism in the evolutionary method of path planning. The problem is considered based on the example of a ship path planning. In this method the diversity of individuals is tested in respect to their physical distance, not the fitness function value. The researches show that such an approach increases effectiveness of solution space exploration, what results in a final solution with...
-
Założenia modelu zarządzania kryzysowego bezpieczeństwem w portach morskich
PublikacjaZłożoność przestrzenna i gospodarcza oraz silne oddziaływanie działalności portowej na procesy społeczno-gospodarcze w regionie, wymaga opracowania specjalnego podejścia do zarządzania bezpieczeństwem na obszarach portowych. W pracy przedstawiono założenia modelu zarządzania kryzysowego bezpieczeństwem w portach morskich uwzględniające zasady międzynarodowego kodeksu ISPS (International Ship and Port Security Code) oraz wymagania...
-
Experimental Comparison of Straight Lines and Polynomial Interpolation Modeling Methods in Ship Evolutionary Trajectory Planning Problem
PublikacjaPaper presents the application of evolutionary algorithms and polynomial interpolation in ship evolutionary trajectory planning method and its comparison to classic approach, where trajectory is modeled by straight lines. Evolutionary algorithms are group of methods that allows\ to find a collision free trajectory in real time, while polynomial interpolation allows to model smooth trajectory, which keeps continuity of velocity...
-
Approach to evaluation of time to the critical degradation of ship pipelines
PublikacjaIn the article an approach to the problem of estimating time to the critical degradation of ship pipelines is considered. Such an assessment would consist of six stages. The fundamental idea is to include to the estimation of time to failure of pipelines such elements like: materials that the pipelines are made, destructive physical phenomena taking place in them and applied means of protection. The result of that evaluation should...
-
Evolutionary Ship Track Planning within Traffic Separation Schemes – Evaluation of Individuals
PublikacjaThe paper presents an extended version of the author’s Evolutionary Sets of Safe Ship Trajectories method. The method plans safe tracks of all ships involved in an encounter including speed reduction manoeuvres, if necessary, and taking into account Rule 10 of COLREGS, which specifies ships’ behaviour within Traffic Separation Schemes governed by IMO. The paper focuses on the evaluation phase of the evolutionary process and shows...
-
Impact of Initial Population on Evolutionary Path Planning Algorithm
PublikacjaIn this paper an impact of initial population on evolutionary path planning algorithm is presented. Tested algorithm is used to determine close to optimal ship paths in collision avoidance situation. For this purpose a path planning problem is defined. A specific structure of the individual path and fitness function is presented. For the simulation purposes a close to real tested environment is created. Four tests are performed....
-
Ship Resistance Prediction with Artificial Neural Networks
PublikacjaThe paper is dedicated to a new method of ship’s resistance prediction using Artificial Neural Network (ANN). In the initial stage selected ships parameters are prepared to be used as a training and validation sets. Next step is to verify several network structures and to determine parameters with the highest influence on the result resistance. Finally, other parameters expected to impact the resistance are proposed. The research utilizes...
-
Monitoring of underdeck corrosion by using acoustic emission method
PublikacjaThis paper presents first short characteristics of underdeck corrosion process as well as a problem of its monitoring. Next is described an acoustic emission (AE) method elaborated by Department of Ship Technology , Quality Systems and Material Engineering, Gdańsk University of Technology in cooperation with partners of CORFAT project realized within 7th EU Frame Program . Further are presented short characteristics of the emission...
-
Evolutionary Sets of Safe Ship Trajectories: problem dedicated operators
PublikacjaThe paper presents the optimization process of the evolutionary sets of safe ship trajectories method, with a focus on its problem-dedicated operators. The method utilizes a customized evolutionary algorithm to solve a constrained optimization problem. This problem is defined as finding a set of cooperating trajectories (a set is an evolutionary individual) of all the ships involved in the encounter situation. The resulting trajectories...
-
The study of acoustic climate of the Southern Baltic
PublikacjaThis paper presents the statistical characteristics of seawater properties, which are necessary for predicting the propagation of acoustic waves in selected areas of the Baltic Sea. The statistics were elaborated based on long-term measurements of vertical distributions of sound speed, temperature, and salinity, and the nonlinearity parameter B/A. Nonlinear properties of the environment are considered, in connection...
-
Predicting a passenger ship's response during evasive maneuvers using Bayesian Learning
PublikacjaThe rapidly advancing automation of the maritime industry – for instance, through onboard Decision Support Systems (DSS) – can facilitate the introduction of advanced solutions supporting the process of collision avoidance at sea. Nevertheless, relevant solutions that aim to correctly predict a ship's behavior in irregular waves are only available to a limited extent by omitting the impact of wave stochastics on resulting evasive...
-
Propagation of Ship-Generated Noise in Shallow Sea
PublikacjaContamination of sea environment by noise and any energy radiated to water constitutes today a problem to which more and more attention is paid, in view, a.o., of consequences of an impact of these factors onto marine fauna. European Union has introduced a directive by which EU countries are made responsible to undertake efforts aimed at reaching a good envirenmental status of European seas by 2020. A main source of underwater...
-
Minimizing Greenhouse Gas Emissions From Ships Using a Pareto Multi-Objective Optimization Approach
PublikacjaTo confront climate change, decarbonization strategies must change the global economy. According to statements made as part of the European Green Deal, maritime transport should also become drastically less polluting. As a result, the price of transport must reflect the impact it has on the environment and on health. In such a framework, the purpose of this paper is to suggest a novel method for minimizing emissions...
-
Assesment of operation of ship main diesel engine using the theory of semi-markovian and markov processes.
PublikacjaTo precisely determine the task it is necessary to specify also its duration time, apart from conditions in which it will be realized. When considering propulsion engine, i.e. the main element of ship propulsion system, especially important becomes not only the problem which amount of energy could be at one's disposal but also within which time interval it could be delivered. Therefore apart from applying the commonly used reliability...