Wyszukiwarka
Filtry
wszystkich: 23
Wyniki wyszukiwania dla: CORRUGATED LINE
-
Analysis of Corrugated Coaxial Line with the Use of Body of Revolution and Finite Element Method
PublikacjaA combination of the body-of-revolution and finite element methods is utilized to the analysis of coaxial lines with corrugated rod and wall. Both periodic and non-periodic structures can be investigated. As the structure is axially symmetrical the two dimensional scalar-vector finite element method can be used, which allows for the investigation of complex geometries and is computationally efficient. A generalized impedance matrix...
-
Stability of roof trusses stiffened by corrugated sheets
PublikacjaThe present parametric study is devoted to the stability analysis of a set of trusses stiffened by decking of corrugated steel sheets. For different parameters of corrugated sheets the critical loading of the roof is calculated. In the parametrical analysis the threshold bracing condition of the roof is obtained. Then the geometrically non-linear analysis of trusses braced by corrugated sheets was conducted. As a results of non-linear...
-
ECONOMICAL AND SAFE METHOD OF GRANULAR MATERIAL STORAGE IN SILOS IN OFFSHORE PORT TERMINALS
PublikacjaThe article discusses issues related with storage of granular materials in silos made of corrugated sheets and reinforced with vertical ribs. Advantages and disadvantages of these structures are named, and typical technological solutions used by largest silo producers are presented. Moreover, basic assumptions of Eurocode 3 are discussed in the context of determining the buckling load capacity of a ribbed jacket. Alternative methods...
-
Compact Dual-Polarized Corrugated Horn Antenna for Satellite Communications
PublikacjaIn this paper, a structure and design procedure of a novel compact dual-polarized corrugated horn antenna with high gain and a stable phase center for satellite communication is presented. The antenna incorporates an Ortho-Mode Transducer (OMT), a mode converter, and a corrugated structure. The compact OMT section is designed to be fed by standard WR-75 waveguides. The proposed compact design utilizes only ten corrugated slots...
-
Buckling of simplified models of silo with corrugated walls and vertical stiffeners
PublikacjaThe paper deals with buckling of cylindrical silos composed of corrugated sheets and vertical stiffeners (columns). Comprehensive finite element analyses were carried out for a perfect silo by means of a linear buckling approach. Corrugated walls were simulated as an equivalent orthotropic shell and vertical thin-walled columns as beam elements. Calculations for perfect silos with different numbers of columns made it possible to...
-
A Wideband Corrugated Ridged Horn Antenna with Enhanced Gain and Stable Phase Center for X- and Ku-Band Applications
PublikacjaIn this letter, a structure and design procedure of a novel double-flared conical horn antenna with an improved gain and a stable phase center is presented. The antenna incorporates a hybrid ridged and corrugated structure. A double-ridged section is responsible for ensuring a wideband operation, whereas the corrugated section supports the hybrid mode. The antenna impedance bandwidth (VSWR < 2) is 6 GHz to 20 GHz. Excellent performance...
-
Application of linear buckling sensitivity analysis to economic design of cylindrical steel silos composed of corrugated sheets and columns
PublikacjaThe paper deals with global stability of steel cylindrical silos composed of corrugated walls and vertical columns with loads imposed by a bulk solid following Eurocode 1. The optimum silo design with respect to the steel weight was based on a sensitivity analysis method. The changes of silo column profiles at each design step were performed by means of influence lines for the buckling load factor due to the unit column bending...
-
Buckling resistance of a metal column in a corrugated sheet silo - experiments and non-linear stability calculations
PublikacjaThe results of experimental and numerical tests of a single corrugated sheet silo column’s buckling resistance are presented in this study. The experiments were performed in a real silo with and without bulk solid (wheat). A very positive impact of the bulk solid on the column buckling resistance occurred. The experimental results were first compared to the buckling resistance calculated by Eurocode 3 formulae. The comparison revealed that...
-
Stability of roof trusses stiffened by trapezoidal sheeting and purlins
PublikacjaIn the article linear buckling analysis of a set of steel trusses braced by purlins and trapezoidal sheeting are conducted. The buckling load factor due to the height of a corrugated sheeting profile is investigated in parametric studies. The minimal height of trapezoidal sheeting required for preventing the sheeting and chords of the trusses against the buckling is obtained. Two groups of models are considered: “axial” model as...
-
Stability of cylindrical steel silos composed of corrugated sheets and columns based on FE analyses versus Eurocode 3 approach
PublikacjaComprehensive static and dynamic 3D stability finite element analyses of a cylindrical steel silo composed of corrugated sheets and open thin-walled vertical stiffener profiles were carried out by taking the geometric and material non-linearity into account. The silowas subjected to axisymmetric and non-axisymmetric loads imposed by a bulk solid following Eurocode 1. Theoretical and measured initial geometric imperfections were...
-
Effect of Sinusoidal Corrugated Geometries on the Vibrational Response of Viscoelastic Nanoplates
PublikacjaThe vibrational behavior of viscoelastic nanoplates with a corrugated geometry is a key topic of practical interest. This problem is addressed here for wrinkled nanoplates with small corrugations related to incorrect manufacturing. To this end, a new One-Variable First-order Shear Deformation plate Theory (OVFSDT) is proposed in a combined form with a non-local strain gradient theory. The Kelvin–Voigt model is employed to describe...
-
Buckling analyses of metal cylindrical silos containing bulk solids during filling
PublikacjaThe paper presents 3D results on stability of thin-walled cylindrical metal silos made of isotropic rolled and corrugated plates containing bulk solids. The behavior of bulk solids was described using a hypoplastic constitutive model. Nonlinear finite element (FE) analyses with both geometric and material nonlinearity were performed with a perfect and an imperfect silo shell wherein initial geometric imperfections were taken into...
-
Impact of Geometrical Imperfections on Estimation of Buckling and Limit Loads in a Silo Segment Using the Vibration Correlation Technique
PublikacjaThe paper examines effectiveness of the vibration correlation technique which allows determining the buckling or limit loads by means of measured natural frequencies of structures. A steel silo segment with a corrugated wall, stiffened with cold-formed channel section columns was analysed. The investigations included numerical analyses of: linear buckling, dynamic eigenvalue and geometrically static non-linear problems. Both perfect...
-
Influence of sheet/purlin fasteners spacing on shear flexibility of the diaphragm
PublikacjaThe paper presents the influence of sheet/purlin fasteners location (in reference to trapezoidal profile cross section) on shear flexibility of the cladding acting as a diaphragm. Analytical procedures were presented and their limitations were discussed. Next, selected schemes of fasteners location, known from engineering practice, but not included in European codes and recommendations, were analysed numerically in order to observe...
-
Correlation between natural frequencies and buckling load in a stiffened shell
PublikacjaThe paper deals with correlation between natural frequencies and buckling load of a stiffened shell composed of corrugated sheets and vertical stiffeners (columns). The simplified shell segment represents the buckling behaviour of a whole silo with sparsely distributed columns. The paper covers variants of linear buckling anal-yses, dynamic eigenvalue analyses and geometrically non-linear analyses of a segment modelled with shell...
-
Influence of fasteners and connections flexibility on deflections of steel building including the stressed skin effect
PublikacjaThe paper presents the analysis of the influence of fasteners and connections flexibility on displacements of symmetrical single-bay pitched-roof steel building, including trapezoidal cladding acting as a diaphragm. The purpose of the article was to compare numerical models with and without taking into consideration fasteners and connections flexibility in order to observe the differences in transverse stiffness of the building...
-
Buckling Analysis of Cold Formed Silo Column
PublikacjaThe paper is devoted to stability analysis of different models of steel cold formed silo column. The steel cylindrical silos are often composed of corrugated walls and vertical open-sectional columns uniformly placed along the silo circumference. Both the whole 3D silo, a simplified model consisting of one column with a part of the silo walls, and a single column resting on elastic foundation provided by the silo walls were analyzed....
-
Testing of the longest span soil-steel bridge in Europe – new quality in measurements
PublikacjaThe article describes interdisciplinary and comprehensive diagnostic tests of final bridge inspection and acceptance proposed for a soil – steel bridge made of corrugated sheets, being the European span length record holder (25.74 m). As an effect of an original concept a detailed and precise information about the structure response was collected. The load test design was based on the nonlinear numerical simulations performed by...
-
The buckling analysis of a cold-formed steel C-sectional column resting on an elastic foundation
PublikacjaThe paper is focused on stability analysis of different models of steel cold-formed C-section column. The analysed element may be applied as a primary load-bearing member in steel trusses or silo columns. The column can be used as a support for a wall of roof plates made of corrugated sheets. The wall sheeting that restrains the column against buckling may be considered as an elastic foundation. Due to the design solutions the...
-
NUMERICAL ANALYSIS OF SPECIES DIFFUSION AND METHANOL DECOMPOSITION IN THERMOCATALYTIC REACTOR BASED ON THE INTERMETALLIC PHASE OF Ni3Al FOR LOW REYNOLDS NUMBERS
PublikacjaNumerical modelling of hydrogen production by means of methanol decomposition in a thermocatalytic reactor using corrugated foil made of the Ni3Al intermetallic phase is shown in the paper. Experimental results of the flow analysis of mixtures containing helium and methanol in a thermocatalytic reactor with microchannels were used for the initial calibration of the CFD calculations (calculations based on the Computational Fluid...
-
Interplay between Aryl···Perfluoroaryl and Hydrogen Bonding Interactions in Cocrystals of Pentafluorophenol with Molecules of Trigonal Symmetry
PublikacjaCocrystals of seven star-shaped triaryl compounds with pentafluorophenol (pfp) were prepared and structurally characterized by the single-crystal X-ray diffraction method. Cocrystallization of pfp with planar (or almost planar) compounds gave six 3:1 molecular complexes with well-defined layered structures. The layers are composed of alternating pfp3 trimers, linked by hydrogen bonding, and triaryl molecules held together in planes...
-
Non-Destructive Testing of the Longest Span Soil-Steel Bridge in Europe—Field Measurements and FEM Calculations
PublikacjaThe article describes interdisciplinary and comprehensive non-destructive diagnostic tests of final bridge inspection and acceptance proposed for a soil-steel bridge made of corrugated sheets, being the European span length record holder (25.74 m). As an effect of an original concept a detailed and precise information about the structure short-term response was collected. Periodic diagnostics of bridge deformations was done one...
-
A Critical Reanalysis of Uncontrollable Washboarding Phenomenon in Metal Band Sawing
PublikacjaThe article analyzes the cutting process of hard bars. Investigations conducted in industrial conditions demonstrated the presence of surface errors in the machined workpieces in the form of washboard patterns. The purpose of this study was to analyze the results of cutting on band sawing machines with different band saw blades. The cutting processes were conducted on three different horizontal band sawing machine types. Analyzed...