Wyszukiwarka
Filtry
wszystkich: 42
Wyniki wyszukiwania dla: EPOXY RESIN
-
Mechanical Properties of Bio-Composites Based on Epoxy Resin and Nanocellulose Fibres
PublikacjaThe aim of our research was to investigate the effect of a small nanocellulose (NC) addition on an improvement of the mechanical properties of epoxy composites. A procedure of chemical extraction from pressed lignin was used to obtain nanocellulose fibers. The presence of nanoparticles in the cellulose pulp was confirmed by FTIR/ATR spectra as well as measurement of nanocellulose particle size using a Zetasizer analyzer. Epoxy...
-
Current-Voltage Characteristics of the Composites Based on Epoxy Resin and Carbon Nanotubes
Publikacja -
Effect of Surface Treatment of Halloysite Nanotubes (HNTs) on the Kinetics of Epoxy Resin Cure with Amines
PublikacjaThe epoxy/clay nanocomposites have been extensively considered over years because of their low cost and excellent performance. Halloysite nanotubes (HNTs) are unique 1D natural nanofillers with a hollow tubular shape and high aspect ratio. To tackle poor dispersion of the pristine halloysite (P-HNT) in the epoxy matrix, alkali surface-treated HNT (A-HNT) and epoxy silane functionalized HNT (F-HNT) were developed and cured with...
-
Kinetics of Cross-Linking Reaction of Epoxy Resin with Hydroxyapatite-Functionalized Layered Double Hydroxides
PublikacjaThe cure kinetics analysis of thermoset polymer composites gives useful information about their properties. In this work, two types of layered double hydroxide (LDH) consisting of Mg2+ and Zn2+ as divalent metal ions and CO32− as an anion intercalating agent were synthesized and functionalized with hydroxyapatite (HA) to make a potential thermal resistant nanocomposite. The curing potential of the synthesized nanoplatelets in the...
-
Curing epoxy resin with anhydride in the presence of halloysite nanotubes: the contradictory effects of filler concentration
PublikacjaEpoxy resins can be cured with a wide variety of curing agents such as amines and anhydrides, but anhydride curing would be more favorable for research purpose because of epoxy-anhydride curing taking place slowly at room temperature. Incorporation of natural nanosized minerals into epoxy is of environmental importance. Halloysite nanotubes (HNTs) display chemical properties similar to those of silica and alumina, and hydroxyl...
-
The Tribological, Physico-Chemical and Rheological Properties of Lubricating Grease Produced on Epoxy Resin Base
Publikacja -
The Effect of Texturing of the Surface of Concrete Substrate on the Pull-Off Strength of Epoxy Resin Coating
Publikacja -
Engineering and Manufacturing Technology of Green Epoxy Resin Coatings Modified with Recycled Fine Aggregates
Publikacja -
Epoxy Composites Filled with Natural Calcium Carbonate. 1. Epoxy Composites Obtained in the Presence of Monoperoxy Derivative of Epidian-6 Epoxy Resin
PublikacjaPhysico-mechanical properties of the products based on filled epoxy-oligomeric mixtures composed of Epidian-5 epoxy resin, oligoesteracrylate TGM-3 and monoperoxide derivative of Epidian-6 epoxy resin (PO) have been investigated. CaCO3 was used as a filler and polyethylene polyamine was a curing agent. The effect of PO and CaCO3 on the gel-fraction content and physico-mechanical properties was examined. Using a scanning electron...
-
The Effect of Recycled Fine Aggregate Sourced from Construction and Demolition Waste on the Properties of Epoxy Resin Coatings
Publikacja -
Synthesis and application of oligomer with hydroxy groups based on peroxy derivative of ED-24 epoxy resin and POLYTHF-2000 oligoether
PublikacjaNew oligomer with peroxy, primary and secondary hydroxy groups has been synthesized on the basis of peroxy derivative of ED-24 epoxy resin (PO) and PolyTHF-2000 oligoether according to the developed procedure. The effect of the catalysts nature and amount, temperature and process time on the reaction rate has been studied. Benzyltriethylammonium chloride, potassium hydroxide,1,4-diazobicyclooctane and the mixture composed of benzyltriethylammonium...
-
RP-HPLC WITH DETECTION BY MEANS OF ESI-MS AND UV FOR IDENTIFICATION OF CHROMATOGRAPHIC PEAKS OF SOME HYDROXY DERIVATIVES OF EPOXY RESIN
PublikacjaThe composition of products synthesized on the basis of ED-24 epoxy resin has been studied using a reversed phase high-performance liquid chromatography followed by an electrospray ionization mass spectrometry (RP-HPLC/ESI-MS). The synthesized products contain free hydroxy groups and such groups, as epoxy, peroxy, carboxy or acrylate.
-
Influence of Storage Time and Temperature on the Toxicity, Endocrine Potential, and Migration of Epoxy Resin Precursors in Extracts of Food Packaging Materials
PublikacjaThe aim of the present study was to establish a standard methodology for the extraction of epoxy resin precursors from several types of food packages (cans, multi-layered composite material, and cups) with selected simulation media (distilled water, 5% ethanol, 3% dimethyl sulfoxide, 5% acetic acid, artificial saliva) at different extraction times and temperatures (factors). Biological analyses were conducted to determine the acute...
-
Polyhydric SiO2 coating assistant to graft organophosphorus onto glass fabric for simultaneously improving flame retardancy and mechanical properties of epoxy resin composites
Publikacja -
Impact Behaviour of Glass Fribre /Epoxy Composites with Nano-Enhanced Resin after Water Exposure
PublikacjaImpact behaviour of glass fibre /epoxy composites with nano- SiO2 modified resin was studied in terms of low velocity impact after water exposure. Nanocomposites with 1%, 2%, 3% 5% 7% nano-SiO2 (Nanopox- Evonic) were investigated. Peak impact load and impact damage area as a function of nanoparticle contents were compared for dry specimens and for samples exposed to water (0.7 %wt. 1.7% water absorbed) at 1J, 2J 3J impact energies....
-
Computational modelling of the modification of epoxy resins
PublikacjaSymulacja komputerowa właściwości fizycznych sieci żywic epoksydowych (DGEBA/DDM) modyfikowanych związkami akrylowymi przy użyciu programu Cheops® MillionZillion Software.
-
Selected biotrends in development of epoxy resins and their composites
PublikacjaEpoxy resins and their fibre or particulate composites are widely used in various industries, including building, naval, aircraft, automotive and aerospace. Modern polymer science and technology focus on the development of green polymers and composites. There are two major areas of interest in the case of epoxy resins: the development of bio-based resins and the production of composites with natural fibers. One of the most interesting...
-
Engineering of composite materials made of epoxy resins modified with recycled fine aggregate
Publikacja -
Cross-linking of epoxy-oligomeric mixtures in the presence of modified phenol-formaldehyde resins
PublikacjaCross-linking of epoxy oligomeric mixtures consisting of industrial epoxy resin ED-20, oligoetheracrylate TGM-3, peroxide derivative of epoxy resin ED-24 and phenol-formaldehyde oligomer with unsaturated methacrylate fragments or peroxide groups was studied in the presence of polyethylenepolyamine at room temperature and heated to 383, 403 or 423 K for 15, 30, 45, 60 and 75 minute. The influence of mixture composition, temperature...
-
Cross-linked epoxy-isocyanate blends containing Epidian-6 modified by glycols
PublikacjaPolymeric films of cross-linked structure may be formed using epoxy-isocyanate blends composed of Epidian-5 epoxy resin, 4,4’-diphenylmethanediisocyanate (MDI), Z-1 polyamine hardener and Epidian-6 epoxy resin modified by glycols. The effect of the component natures and ratio, process temperature and time on the gel-fraction content, as well as film hardness, was examined. The chemistry of the film forming process was determined...
-
New Transparent Flame-Retardant (FR) Coatings Based on Epoxy-Aluminum Hypophosphite Nanocomposites
PublikacjaThe present study investigated the flame-retardant (FR) effect of transparent epoxy coating containing aluminum hypophosphite (AHP) nanoparticles (NPs) on polylactic acid (PLA) sheets used as a typical model of combustible polymeric material. First, AHP NPs (≤60 nm) were prepared by a specific two-stage wet milling process and deeply analyzed (morphology, thermal/mechanisms of degradation under nitrogen and air). The thermal properties...
-
Development of nanoscale morphology and role of viscoelastic phase separation on the properties of epoxy/recycled polyurethane blends
PublikacjaA novel and cost-effective approach towards the modification of epoxy matrix has been developed using recycled polyurethane for the first time without sacrificing any of the intrinsic properties of the resin. Polyurethane, recycled from waste foam by glycolysis process (RPU), was found to be very effective in improving the properties of the thermosetting resin based on Diglycidyl ether of bisphenol-A (DGEBA). The effect of the...
-
Toughness augmentation by fibrillation and yielding in nanostructured blends with recycled polyurethane as a modifier
PublikacjaIn the present paper, we have carefully investigated the morphology and fracture mechanism of the recycled polyurethane (RPU) /epoxy blend system. The second phase (RPU) added to the epoxy resin has a positive effect on the overall mechanical properties. Interestingly, the recycled polymer has a remarkable effect on the fracture toughness of epoxy resin. The mechanism behind the fracture toughness improvement up on the addition...
-
Integration of antifouling properties into epoxy coatings: a review
Publikacjahe need for nontoxic antifouling coatings has encouraged material scientists to develop a class of organic coatings for diverse applications. As a versatile thermosetting resin and well known for coating application, antifouling characteristics have been integrated into epoxy along with anticorrosion and adhesive functions. Accordingly, both micro- and macro-biofoulings have been successfully controlled by using epoxy-based antifouling...
-
Submicron inorganic particles as an additional filler in hybrid epoxy matrix composites reinforced with glass fibres
PublikacjaIn this study, the effect of selected submicron metal oxide (zinc oxide, titanium oxide) or non-metal oxide (silicon dioxide) particles on mechanical and thermo-mechanical properties of epoxy/glass composites was investigated. The applied epoxy resin was a diglycidyl ether of bisphenol-A cured with triethylenetetramine. As a reinforcement twill weave E-glass fabric was used. Hybrid composites (contained particulate and fibrous...
-
Curing epoxy with ethylenediaminetetraacetic acid (EDTA) surface-functionalized Co Fe3-O4 magnetic nanoparticles
PublikacjaIn this work, the bulk and surface composition of Fe3O4 supermagnetic nanoparticles were modified for efficient epoxy curing. The bare, ethylenediaminetetraacetic acid (EDTA) capped, and cobalt (Co)-doped EDTA capped Fe3O4 nanoparticles were synthesized electrochemically. The crystalline structure and phase information, surface capping, morphology and magnetization behavior of nanoparticles were studied by X-Ray diffraction (XRD),...
-
Sensing the onset of epoxy coating degradation with combined Raman spectroscopy/atomic force microscopy/electrochemical impedance spectroscopy
PublikacjaThe paper presents the results of investigation on epoxy resin durability upon 12-week exposure to UV radiation. The aim was early determination of the onset of epoxy degradation and for this purpose an epoxy film on steel substrate systems were periodically inspected using Raman spectroscopy, atomic force microscopy and electrochemical impedance spectroscopy. The behaviour of examined polymer could be divided into three periods: immunity,...
-
Cure kinetics of epoxy/MWCNTs nanocomposites: Nonisothermal calorimetric and rheokinetic techniques
PublikacjaNonisothermal calorimetric and isothermal rheokinetic analyses were used to study cure kinetics of epoxy/anhydride systems containing very low concentration of pristine and amine-functionalized multiwalled carbon nanotubes (MWCNTs). Isoconversional methods were applied in calorimetric modeling of cure kinetics. Eα vs. α dependency and autocatalytic nature of curing were identified for both types of nanocomposites by isoconversional...
-
Biowaste chicken eggshell powder as a potential cure modifier for epoxy/anhydride systems: competitiveness with terpolymer-modified calcium carbonate at low loading levels
PublikacjaBiowaste chicken eggshell (ES) powder was applied as a potential cure modifier in epoxy/anhydride systems. Cure behaviour and kinetics of composites filled with very low content (0.1 wt% based on epoxy resin) of ES, calcium carbonate (CaCO3), and terpolymer-modified fillers, mES and mCaCO3, were discussed comparatively. Surface analysis was performed by X-ray photoelectron spectroscopy. Cure kinetics was investigated by differential...
-
Impact damage in SiO2 nanoparticle enhanced epoxy – Carbon fibre composites
PublikacjaLow velocity impact behaviour of nano-SiO2 enhanced carbon fibre/epoxy composites for naval applications is reported. Epoxy resin matrix was enhanced by 1- 8 wt% SiO2 nanoparticles, based on industrial surface-modified nanosilica. Impact parameters: force, deformation, energy, damage size were recorded. The most pronounced effect was damage size decrease; e.g. ∼28% recorded by infrared thermography and X-ray computed radiography...
-
Properties of nano-Fe3O4 incorporated epoxy coatings from Cure Index perspective
PublikacjaThe mission of an advanced epoxy-based nanocomposite coating is to provide a given substrate with protection against an unwelcome guest; e.g. corrosive molecules/media, environmental stress, flame, thermal degradation or microorganisms. In such systems, the degree to which superior properties can be guaranteed depends on the state of network formation in the epoxy in the presence of nanoparticles. For low-filled epoxy nanocomposite coatings,...
-
In-Out Surface Modification of Halloysite Nanotubes (HNTs) for Excellent Cure of Epoxy: Chemistry and Kinetics Modeling
PublikacjaIn-out surface modification of halloysite nanotubes (HNTs) has been successfully performed by taking advantage of 8-hydroxyquinolines in the lumen of HNTs and precisely synthesized aniline oligomers (AO) of different lengths (tri- and pentamer) anchored on the external surface of the HNTs. Several analyses, including FTIR, H-NMR, TGA, UV-visible spectroscopy, and SEM, were used to establish the nature of the HNTs’ surface engineering....
-
Obtaining of Coumarone-Indene Resins Based on Light Fraction of Coal Tar. 4. Bitumen-Polymer Blends with Participation of Coumarone-Indene Resins with Epoxy Groups
PublikacjaUsing light fraction of coal tar (5.75 wt % of coumarone and 44.45 wt % of indene), glycidyl methacrylate and styrene, the coumarone-indene resin with epoxy groups (CIRE) has been synthesized. Monoperoxy derivative of diglycidyl ether Bisphenol A (PO) was used as an initiator. The possible formation of CIRE has been studied on the model systems consisting of PO, glycidyl methacrylate, indene or coumarone, or styrene, or mixture...
-
Polyurethane glycolysate from industrial waste recycling to develop low dielectric constant, thermally stable materials suitable for the electronics
PublikacjaWe are utilizing a new method to improve the dielectric properties of a conventional polymer using a recycled polymer product. The polyurethane foams are recycled by glycolysis process and the derived material was applied to improve the dielectric properties of the brittle DGEBA epoxy resin. Two main parameters that determine the applicability of the material as a dielectric (the dielectric constant and dielectric loss), were studied...
-
COMPOSITE MATERIAL SELECTION FOR A PATIENT TRANSFER ASSIST DEVICE
PublikacjaLaminates - layered composites containing at least two elements (matrix and reinforcement) widely used in industry have also found their usage in medicine. Their main feature is the ability to modify the material in order to obtain the required properties. Depending on the needs, we can modify reinforcement, type of resin or the method of bonding substrates. Commonly used fibers are: carbon fiber, glass and aramid fibers; resins...
-
Evaluating the influence of radiative heat flux on convective heat transfer from a vertical plate in air using an improved heating plate
PublikacjaThis article examines the influence of radiative heat flux on the accuracy of the results of free convective heat transfer in air. In order to carry out these tests, based on the experience gained during the operation of a plate heated on one side, compensated by a reverse heat loss flux counter-heater, a unique double-sided heating sandwich plate was designed and built, consisting of three thin epoxy resin plates reinforced with...
-
Detection of Delamination in Laminate Wind Turbine Blades Using One-Dimensional Wavelet Analysis of Modal Responses
PublikacjaThis paper demonstrates the effectiveness of a nondestructive diagnostic technique used to determine the location and size of delamination in laminated coatings of wind turbine blades. This is realized based on results of numerical and experimental investigations obtained by the use of the finite element method (FEM) and laser scanning vibrometry (LSV). The proposed method is based on the one-dimensional continuous wavelet transform...
-
Synthesis, structure and properties of novel poly(hydroxyurethane)s obtained by non-isocyanate route
PublikacjaNon-isocyanate polyurethanes (NIPUs) can be synthesized by polyaddition of five-membered bis(cyclic carbonate)s and primary diamines. NIPUs are an alternative for the commonly used (in the form of foams, elastomers, coatings or fibers) in the industry polyurethanes obtained using toxic and moisture sensitive diisocyanates, polyols and low-molecular weight chain extenders. The main aim of this work was to synthesize non-isocyanate...
-
Mechanical response of human thoracic spine ligaments under quasi-static loading: An experimental study
PublikacjaPurpose This study aimed to investigate the geometrical and mechanical properties of human thoracic spine ligaments subjected to uniaxial quasi-static tensile test. Methods Four human thoracic spines, obtained through a body donation program, were utilized for the study. The anterior longitudinal ligament (ALL), posterior longitudinal ligament (PLL), capsular ligament (CL), ligamenta flava (LF), and the interspinous ligament and...
-
The effect of hybridization of fire retarded epoxy/flax-cotton fiber laminates by expanded vermiculite: Structure-property relationship study
PublikacjaThe study describes the hybridization of epoxy/flax-cotton (EP/FF) composites containing ammonium polyphosphate (APP) with micrometric expanded vermiculite (VMT) (1–10 wt%). The efficiency of hybridization of flame retarded epoxy/flax-cotton composites was assessed by performing static tensile and flexural strength evaluation, supplemented by impact strength measurements of the composites. Moreover, thermal and thermomechanical...
-
Synthesis and properties of carboxy derivative of Epidian 6 monomethacrylate (in English)
PublikacjaWe present the synthesis of an oligomer with carboxy and methacrylic groups based on Epidian 6. The effect of the catalyst nature and amount, solvent nature and process temperature on the rate of the reaction between Epidian6 monomethacrylate and adipic acid was examined at 313, 323 and 333 K in the presence of 4-dimethylaminopyridine, 1,4-diazobicyclo[2.2.2]octane, and benzyltriammonium chloride. The synthesized oligomer was characterized...
-
Aiswarya Manohar
OsobyI joined as a PhD student in Gdansk tech university of Technology in 2022. In my scientific work, I am primarily focusing on studies related to 3D printing, laser induced graphene, electrochemical sensors and biosensors as well as micro arc oxidation, corrosion, and degradation with emphasis on impedance spectroscopy studies of electrode processes. I am specializing in Materials and surface modifications and characterization. ...