Wyszukiwarka
Wyniki wyszukiwania dla: HYDRODYNAMIC THRUST BEARING
-
Large hydrodynamic thrust bearing: Comparison of the calculations and measurements
PublikacjaHydrodynamic thrust bearings, used to carry axial loads in heavily loaded shafts of water power plants hydro turbines, can reach outer diameters even exceeding 5 m. In such large objects scale effect could be observed. According to this, allowable bearing specific load assuring safe operation of the bearings has to be decreased, which increases thrust bearing dimensions. This effect is caused by excessive thermal deflections of...
-
Influence of Collar Deformations on Hydrodynamic Thrust Bearing Performance
Publikacja -
Effect of manufacturing errors of the pad sliding surface on the performance of the hydrodynamic thrust bearing
PublikacjaIn the present study, investigation of the effect of manufacturing errors on the performance of large tilting pad thrust bearings has been performed, following a CFD-based Thermohydrodynamic analysis of a single pad. A 3D model has been generated, including the pad, the lubricant film and the corresponding part of the collar. The pad has been assumed to be deformed about the pivot point, due to thrust loading. Manufacturing errors...
-
HYDRODYNAMIC THRUST BEARINGS WITH POLYMER LINING
PublikacjaPolymeric linings of sliding surfaces of the hydrodynamic bearings have been used successfully for over 50 years. Despite of their long history of operation and research, they have not become wide spread in industrial applications. This fact may be surprising, considering th e conclusions that have been published concerning bearing operation and design. This paper summarizes the current...
-
Experimental research on a hydrodynamic thrust bearing with hydrostatic lift pockets: Influence of lubrication modes on bearing performance
PublikacjaThe aim of the study is to investigate the performance of a thrust bearing equipped with hydrostatic lift pockets under different lubrication modes. Three types of flat land bearing lubrication modes are studied experimentally: hydrostatic lubrication (HS; forced oil injection to the pockets), hybrid lubrication (HS + HD; hydrostatic lubrication combined with the external forced bearing oil supply) and hydrodynamic lubrication...
-
Large Hydrodynamic Thrust Bearings and Their Application in Hydrogenerators
PublikacjaLarge hydrodynamic thrust bearings are the bearings which, due to hydrodynamic lubrication, allow large axial load to be transferred from a moving part (shaft) to the stationary part via a thin layer of the lubricant (usually oil), thus providing extremely low friction and practically no wear. Hydrogenerators with vertical shafts are the most important application of large thrust bearings. Main design and scientific problems of...
-
Evaluation of water turbine hydrodynamic thrust bearing performance on the basis of thermoelastohydrodynamic calculations and operational data.
PublikacjaW pracy przedstawiono analizę konstrukcji łożyska wzdłużnego turbiny wodnej. Łożysko zostało skonstruowane około 50 lat temu, a jego konstrukcja przewiduje kompensację termicznych odkształceń klocków. W analizie uwzględniono odkształcenia łożyska i wymianę ciepła w filmie smarowym i klockach łożyskowych. Poza obecną konstrukcją łożyska przeprowadzono również studium wpływu podstawowych parametrów konstrukcyjnych: grubości klocka...
-
Evaluation of water turbine hydrodynamic thrust bearing performance on the basis of thermoelastohydrodynamic calculations and operational data
Publikacja -
Experimental comparison of hydrodynamic thrust bearings with different pad surface materials
PublikacjaBabbitt is the material most frequently used as the pad surface material for hydrodynamic bearings operating at usual operating conditions. It shows many advantages important for safe bearing operation, as for example: low friction coefficient, corrosion resistance, fair mechanical properties and outstanding conformability. On the other hand, it is not free from disadvantages, such as limited fatigue strength or limited resistance...
-
Wpływ odkształceń tarczy oporowej wału na właściwości hydrodynamicznego łożyska wzdłużnego = Influence collar deformations of hydrodynamic thrust bearing performance
PublikacjaPodjęto próbę określenia możliwego wpływu deformacji termosprężystej tarczy oporowej łożyska na jego cechy. Porównano wyniki trzech wariantów obliczeń TEHD: bez uwzględniania deformacji tarczy, z uwzględnieniem deformacji tylko sprężystych oraz z uwzględnieniem deformacji termosprężystych tarczy oporowej.
-
Field Tests on Hydrodynamic and Hybrid Operation of a Bidirectional Thrust Bearing of a Pump-Turbine
PublikacjaIn vertical shaft pump turbines operating in pumped storage power plants an important role is played by a thrust bearing. Due to the bidirectional character of operation, thrust bearing tilting pads have to be supported symmetrically, which is known to be unfavourable from the point of view of their performance. Large thrust bearings have to be carefully designed so as to minimise excessive thermo-elastic pad deformations. The...
-
Ocena wybranych własności materiałowych polimerowej warstwy ślizgowej hydrodynamicznego łożyska wzdłużnego = An estimation of selected material properties of the hydrodynamic thrust bearing polymer lining
PublikacjaZaprezentowano metody pomiaru najważniejszych własności mechanicznych i cieplnych polimerowego pokrycia segmentowego łożyska wzdłużnego, do których zaliczyć należy moduł sprężystości wzdłużnej oraz współczynnik przewodności cieplnej materiału dodatkowym utrudnieniem planowanego zadania jest fakt, że próbka do badań dostępna będzie jedynie w formie wycinka z segmentu łożyskowego, z tego powodu nie jest możliwe zastosowanie ogólnie...
-
Field tests on hydrodynamic and hybrid operation of a bi-directional thrust bearing of a pump-turbine
PublikacjaIn vertical shaft pump turbines operating in pumped storage power plants an important role is played by a thrust bearing. Because of bi-directional character of operation, thrust bearing tilting pads have to be supported symmetrically, which is known to be unfavourable from the point of view of their performance. Large thrust bearings have to be carefully designed so as to minimise excessive thermo-elastic pad deformations. The...
-
Evaluation of apparent Young׳s modulus of the composite polymer layers used as sliding surfaces in hydrodynamic thrust bearings
PublikacjaHydrodynamic bearings with a polymer sliding layer are able to operate in severe conditions, mainly due to favorable properties of the polymers. The goal of this research was to evaluate apparent Young׳s modulus of two types of the polymer composite layers used for sliding surfaces in hydrodynamic bearings, as a function of temperature. The Young׳s modulus was evaluated on the basis of compression tests carried out on samples obtained...
-
EXPERIMENTAL STUDY OF DIFFERENT SUPPLY DESIGNS IN HYDRODYNAMIC THRUST BEARINGS = Badania doświadczalne różnych sposobów smarowania wzdłużnych łożysk ślizgowych
PublikacjaHydrodynamiczne łożyska wzdłużne charakteryzują się znacznymi stratami tarcia, które przyczyniają się do wzrostu temperatury łożyska i obniżenia jego nośności. Obecnie olej smarujący jest zazwyczaj chłodzony w zewnętrznych układach chłodzenia. Po schłodzeniu olej jest dostarczany z powrotem do korpusu łożyska, z reguły do przestrzeni między klockami łożyska. Skuteczność dostarczania schłodzonego oleju w pobliże wlotu do szczeliny...
-
Analiza przepływu oleju przez rowek smarowy wzdłużnego łożyska ślizgowego = Analysis of the lubricant flow through the hydrodynamic thrust bearings groove
PublikacjaSmarowanie zanurzeniowe jest tradycyjnym sposobem smarowania wzdłużnych łożysk ślizgowych. Jednak rozwiązanie to wykazuje umiarkowaną skuteczność w zapewnieniu optymalnie niskich temperatur w filmie smarowym a ponadto jest przyczyną strat mocy związanych z mieszaniem oleju w obudowie łożyska, co jest szczególnie widoczne w łożyskach szybkoobrotowych. Wymagania stawiane nowym konstrukcjom łożysk ślizgowych to zwiększanie nośności...
-
HYDROSTATIC THRUST BEARING WITH REDUCED POWER LOSSES
PublikacjaIn many cases in rotating machinery, axial load is carried by tilting pad thrust bearings which have been developed since the beginning of 20th century. For high reliability and simplicity, most commonly the bearings are bath lubricated. In the times of sustainable development, however, minimization of friction losses becomes an important criterion for machinery assessment, and a strategic goal of their development. Performed calculations,...
-
Wpływ założeń modelu obliczeniowego na wyniki obliczeń hydrodynamicznych łożysk wzdłużnych = The influence of model simplifications on the predicted performance of hydrodynamic thrust bearings
PublikacjaPrzedstawiono porównanie wyników obliczeń hydrodynamicznych łożysk wzdłużnych otrzymanych z wykorzystaniem dwóch niezależnie opracowanych modeli obliczeniowych TEHD (termoelastohydrodynamicznych). Wykorzystane w obliczeniach programy różnią się głównie założeniami i uproszczeniami przyjętymi, zwłaszcza w odniesieniu do części przepływowej zadania. Symulacje obliczeniowe przeprowadzono stosując w przypadku obu modeli te same warunki...
-
Obliczeniowa analiza wybranych systemów dostarczania smaru w hydrodynamicznych łożyskach wzdłużnych = Computational analysis of selected supply designs in hydrodynamic thrust bearings
PublikacjaPrzedstawiono przykładowe wyniki obliczeniowej analizy wpływu zastosowania wybranych systemów dostarczania schłodzonego oleju do łożyska na właściwości łożyska.
-
Prospects of Decreasing Power Losses in a Hydrostatic Thrust Bearing
PublikacjaIn numerous machines, axial load is carried by tilting pad thrust bearings known since the beginning of 20th century. These bearings are commonly bath lubricated, which is simple, does not require any additional pumps, and, due to this, such systems are highly reliable. In a contemporary technology, however, minimization of friction losses became an important goal of machinery improvement. Calculations based on elementary rules...
-
Modeling lubricant flow between thrust-bearing pads
PublikacjaInlet temperature is one of the main inputs in all models for the analysis of fluid film bearing performance. At the same time, inlettemperature distribution and also oil velocity distribution at the inlet are the result of flow phenomena in the gap between the bearingpads. These phenomena are complex and in many cases further affected by any special arrangements of forced oil supply to the gapbetween pads. The reason for such...
-
Hydrodynamic pressure in micro-and nano bearing gap
Publikacja.
-
Hydrodynamic journal bearing - ''Y'' particularly for steam turbines.
PublikacjaW artykule przedstawiono koncepcję i zasadę działania nowego, ślizgoweo łożyska poprzecznego typu ''Y''. Przedstawiono wady i zalety nowego rozwiązania. Porównano charakterystyki dynamiczne i statyczne klasycznego łożyska cytrynowego (soczewkowego) z nowym łożyskiem ''Y''.Podano przykładowe wdrożenia i ich efekty.
-
Effect of Coating Material Properties on Tilting-pad Thrust Bearing Performance
PublikacjaPolymer lined tilting-pad bearings demonstrate many advantages over traditional bearing systems. Bearings with a polymer layer in comparison with a babbitted layer show, for example: lower value of friction coefficient (important during start/stops), higher fatigue strength of the coating, better distribution of the load on individual pads due to lower elasticity of the polymers, wider range of operational temperatures or the ability...
-
Compliance tests of the polymer layers used as hydrodynamic bearing coatings
PublikacjaOperational experience and scientific investigations results showed that polymer lined hydrodynamic bearings can withstand more severe operating conditions compared than white metal bearings. PTFE and PEEK-based coatings are the most frequently used as Babbitt alternatives. Both polymers differ significantly from the each other in material properties. According to catalogue data compression modulus of PTFE, it is about an order...
-
Combined thrust radial bearing of a submarine main shaft – Design and analysis of failure
PublikacjaThis paper presents an analysis of the combined thrust radial bearing of a submarine propulsion shaft. The lubrication system of the bearing is based on a fixed ring. The efficiency of the lubrication system depends on the shaft speed and temperature, which affects oil viscosity. In turn, the thrust bearing load also depends on the rotational speed of the shaft, because as the speed increases, the drag of the ship increases simultaneously,...
-
Simulation of large thrust-bearing performance at transient states, warm and cold start-up
PublikacjaThe start-up of a large hydrodynamic thrust bearing of a vertical hydrogenerator is one of the most critical situations during the lifetime of a bearing. Hydrodynamic load capacity is low due to low speed and higher thermal deformations of the pad. A new approach to the simulation of a hydrodynamic bearing is shown in this article. A combination of finite elements method and computational fluid dynamics is used to perform the transient...
-
Effect of presence of lifting pocket on the THD performance of a large tilting-pad thrust bearing
PublikacjaHydrostatic assistance is a commonly used method to improve limited load carrying ability of tiltingpad thrust bearings during transient states of operation of vertical shaft hydro-generators. Despite of special hydraulic equipment (as pumps, valves, etc.), it also requires manufacturing of special recesses/pockets at pad sliding surfaces, into which oil is injected under high pressure. It allows to lift the rotor before start-up...
-
Improvement of Thrust Bearing Calculation Considering the Convectional Heating within the Space between the Pads
PublikacjaA modern thrust bearing tool is used to estimate the behavior of tilting pad thrust bearings not only in the oil film between pad and rotating collar, but also in the space between the pads. The oil flow in the space significantly influences the oil film inlet temperature and the heating of pad and collar. For that reason, it is necessary to define an oil mixing model for the space between the pads. In the bearing tool, the solutions...
-
Effect of the Presence of the Lifting Pocket on The THD Performance of a Large Tilting-Pad Thrust Bearing
PublikacjaIn this paper, an attempt was taken to study the effect of the lifting pocket on THD performance of a large tilting-pad thrust bearing of Itaipu power plant. B3earing performance was evaluated including recess shape for several cases of its depth. The results show, that hydrostatic recess changes calculated bearing properties quite significantly, especially in the vicinity of the pocket
-
Improvement of the thrust bearing calculation considering the convectional heating within the space between the pads
PublikacjaA modern thrust bearing calculation tool should consider not only the oil film between pad and rotating collar but also the space between the pads. The oil flow in the space has a significant influence on the oil film inlet temperature, the convectional cooling of pad and collar and should be included in the bearing calculation methods. The authors use a tool developed at Clausthal University of Technology in cooperation with the...
-
Study of the Influence of Heat Convection Coefficient on Predicted Performance of a Large Tilting-Pad Thrust Bearing
PublikacjaPart of the heat generated by the shearing of the lubricating film during operation of a hydrodynamic bearing is transferred to the bearing components. In the case of the pad, which is usually fully submerged in the lubricating oil, heat is further transferred at the pad free walls to the oil by convection. This mechanism causes a thermal gradient in a pad and, consequently, its thermal deflection. In large hydrodynamic thrust...
-
A comparative performance assessment of a hydrodynamic journal bearing lubricated with oil and magnetorheological fluid
PublikacjaThis work presents the investigation results of a journal bearing lubricated with magnetorheological fluid that is activated by a local constant magnetic field to vary both the local flow resistance and pressure. The bearing performance is assessed via Finite Element Modelling (FEM) and results are corroborated by experiments. The FEM model uses the Bingham model to describe the fluid film. A dedicated test rig is used to assess...
-
Analiza przepływu oleju przez rowek smarowy wzdłużnego łożyska ślizgowego z wykorzystaniem komputerowej dynamiki płynów (CFD) = Analysis of the lubricant flow through the hydrodynamic thrust bearings groove with the use of computational fluid dynamic
PublikacjaSmarowanie zanurzeniowe jest tradycyjnym sposobem smarowania wzdłużnych łożysk ślizgowych. Jednak rozwiązanie to wykazuje umiarkowaną skuteczność w zapewnieniu optymalnie niskich temperatur w filmie smarowym a ponadto jest przyczyną strat mocy związanych z mieszaniem oleju w obudowie łożyska, co jest szczególnie widoczne w łożyskach szybkoobrotowych. Obecnie wymagania stawiane nowym konstrukcjom łożysk ślizgowych to zwiększanie...
-
Influence of hydrostatic pump operation period on performance of a thrust bearing of a 125 MW pump-turbine.
PublikacjaW pracy przedstawiono wyniki badań eksploatacyjnych łożysk wzdłużnych pompoturbin 125 MW elektrowni szczytowo pompowej (esp) Żar. W celu oceny warunków pracy łożysk wyposażono je w segmenty pomiarowe umożliwiające pomiary temperatury i położenia segmentu. W pracy omówiono konstrukcję i wyposażenie segmentu badawczego, metodykę wyznaczania charakterystycznych wielkości. Omówiono także wyniki badań wpływu czasu pracy pompy hydrostatycznego...
-
Influence of hydrostatic pump operation period on performance of a thrust bearing of a 125 MW pump-turbine
Publikacja -
ANALYSIS OF THE LOAD-CARRYING CAPACITY OF A HYDRODYNAMIC WATER-LUBRICATED BEARING IN A HYDROELECTRIC POwER PLANT
PublikacjaThe paper presents an analysis of the load-carrying capacity of a historic hydrodynamic water-lubricated radial bearing of an unconventional segment design installed in the Braniewo Hydroelectric Power Plant. The aim of the calculations was to determine whether the bearing operates in the conditions of hydrodynamic or mixed lubrication, as well as to establish the optimal geometry of the axial grooves allowing for the highest load-carrying...
-
Experimental comparison of the transition speed of a hydrodynamic journal bearing lubricated with oil and magnetorheological fluid
PublikacjaA journal bearing test bench is used to find the transition speed between the hydrodynamic and mixed lubrication regimes for a modified magnetorheological (MR) fluid. It is shown that the transition speed of the bearing can be reduced by applying a local magnetic field near minimum film when it is lubricated with the MR fluid, and that this will only marginally increase friction. The lubricating performance of the MR fluid is compared...
-
Tilting pad thrust bearing with novel material selection - experimental comparison of low and medium speed operation
PublikacjaThe advances in material engineering led to the development of hard carbon based coatings applied in numerous applications in order to prevent or minimize wear of the parts in contact. With Triondur® coatings, the bearing company Schaeffler has succeeded in halving the friction losses in the valve trains of passenger cars. The coatings are optimized for high abrasive wear protection and low sliding friction moments. Altogether...
-
ANALYSIS OF BEARING CLEARANCE AND WIDTH OF OIL GROOVE ON CHARACTERISTIC OF FLUID FILM IN HYDRODYNAMIC MAIN CRANKSHAFT BEARINGS
PublikacjaAbstract Paper represents analysis of influence of oil groove width and bearing clearance on characteristics of oil film in hydrodynamic journal main crankshaft bearing. Analysis was performed in purpose to define influence of bearing clearance and dimensions of oil groove on static characteristics and manufacturability of half shelf bearings in industrial high-volume production. Computer simulations was made using ARTbear program...
-
Centrally Pivoted Tilting Pad Thrust Bearing with Carbon-Based Coated Collar—Experimental Results of Low- and Medium-Speed Operation
PublikacjaExperimental results of the research on a tilting pad thrust bearing with symmetrical pad support in the conditions of high loads and low speeds are presented in the paper. As described in the literature review, experimental results of tilting pad bearings at low speed/high load regime and transient conditions are rare. Unusual material selection - steel pad against a DLC-type coating on the collar was utilized. Such material combination...
-
Badania teoretyczne łożysk ślizgowych podpartych na czaszy kulistej = Theoretical tests of hydrodynamic journal bearing with self-aligning spherical support
PublikacjaPrzedstawiono metodykę badań teoretycznych i doświadczalnych łożysk ślizgowych podpartych na czaszy kulistej. Badania teoretyczne prowadzono z wykorzystaniem programu komputerowego MES oraz programu wyznaczającego charakterystyki filmu olejowego. W celu opisu systemu tribologicznego łożysko-podpora stworzono trójwymiarowy model MES łożyska i gniazda. W czasie badań analizowano wpływ wielu czynników mogących ułatwiać lub utrudniać...
-
Michał Wasilczuk prof. dr hab. inż.
OsobyMichał Wasilczuk, absolwent Wydziału Budowy Maszyn Politechniki Gdańskiej (1986), a obecnie profesor zwyczajny na Wydziale Mechanicznym PG i kierownik Katedry Konstrukcji Maszyn i Pojazdów od początku swojej działalności naukowej zajmuje się hydrodynamicznymi łożyskami wzdłużnymi oraz, szerzej inżynierią łożyskowania, w ramach zespołu naukowego stworzonego przez doc. Olgierda Olszewskiego. Od kilkunastu lat zespół specjalizuje...
-
Application of the fluid–structure interaction technique for the analysis of hydrodynamic lubrication problems.
PublikacjaFluid–structure interaction technique seems to be one of the most promising possibilities for theoretical analysis of lubrication problems. It allows coupling of different physical fields in one computational task, taking into account the interaction between them. In this article, two sets of fluid–structure interaction analyses focusing on the bearing performance evaluation are presented. One analysis was applied to a water-lubricated...
-
The effect of the exposure-in-oil on the contact of the polymers forming sliding layers in hydrodynamic bearings. Wpływ ekspozycji w oleju na kąt zwilżania polimerów stosowanych na warstwy ślizgowe w łożyskach hydrodynamicznych.
PublikacjaPolimery stosowane jako warstwy ślizgowe w hydrodynamicznych łożyskach wzdłużnych to zazwyczaj tworzywa termoplastyczne charakteryzujące się relatywnie wysokimi wartościami kątów zwilżania w porównaniu z metalami. Metale, w tym również Babbitt czy inne stopy łożyskowe, cechują niskie wartości kątów zwilżania. Im niższy kąt, tym powierzchnia lepiej się zwilża. Tworzywa sztuczne wykorzystywane w węzłach tribologicznych mających zapewnić...
-
Experimental study on the feasibility of alternative materials for tilting pad thrust bearings operating in transition to mixed friction
PublikacjaIn hydrodynamic bearings traditional bearing alloys: Babbitts and bronzes are most frequently utilized. Polymer sliding layers are sometimes applied as a valuable alternative. Hard diamond-like carbon (DLC) coatings, which are also considered for certain applications may show some advantages, as well. Although material selection is of secondary importance in a full film lubrication regime it becomes important in mixed friction...
-
Measurement file of stainless stell shaft LSS1 and LSS2 with diameter 95,995 with 3d measurment device
Dane Badawcze3d point cloud consist of measured points on new stainless steel shaft used during testing hydrodynamic journal PEEK bearing.
-
Should we seek further improvement of fluid film bearings - what for and how?
PublikacjaFluid film bearings have been extensively used in the industry because of their unbeatable durability and extremely low friction coefficient. Large bearings supporting shafts of huge and important rotating machines constitute a special group of fluid film bearings since the reliability of crucial systems, like for example electro-energetic system, rely on their trouble-free operation. Large thrust bearings, apart from enormous...
-
Improving performance of large thrust bearings through modeling and experimentation
PublikacjaLarge thrust bearings are highly loaded machine elements and their failures cause serious losses. Start ups and stoppages of the bearing under load are specially critical regimes of operation. Load carrying capacity depends on the profile of the oil gap. In transient states this profile is also changing. In the design of large thrust bearings minimizing thermo-elastic deformations is an important goal, which can be accomplished...
-
On the Possibilities of Decreasing Power Loss in Large Tilting Pad Thrust Bearings
PublikacjaJournal Menu About this Journal Abstracting and Indexing Aims and Scope Article Processing Charges Articles in Press Author Guidelines Bibliographic Information Citations to this Journal Contact Information Editorial Board Editorial Workflow Free eTOC Alerts Publication Ethics Submit a Manuscript Table of Contents Abstract Full-Text PDF Full-Text HTML...