Wyszukiwarka
Filtry
wszystkich: 3058
-
Katalog
- Publikacje 2564 wyników po odfiltrowaniu
- Czasopisma 86 wyników po odfiltrowaniu
- Konferencje 5 wyników po odfiltrowaniu
- Osoby 83 wyników po odfiltrowaniu
- Projekty 3 wyników po odfiltrowaniu
- Kursy Online 63 wyników po odfiltrowaniu
- Wydarzenia 24 wyników po odfiltrowaniu
- Oferty 1 wyników po odfiltrowaniu
- Dane Badawcze 229 wyników po odfiltrowaniu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: INDUCTIVE POWER TRANSMISSION
-
Research and Development of Inductive-Resonant Wireless Power Transfer System
Publikacja -
COMPARATIVE EVALUATION OF FERRITE SHIELDING DESIGNS IN INDUCTIVE POWER TRANSFER SYSTEMS
PublikacjaWireless power transfer technology is becoming widespread in last few years. In comparison to conventional solutions this technology can significantly increase maintainability and safety of charging systems. From the other side there are list of factors that limit efficiency of wireless systems. One of them is low coupling between coils caused by comparably high leakage inductance in comparison to regular transformer.
-
Predictive method of improvement of the generators rated power usage in inductive heating
Publikacja -
Installation of Compensators in the Power System Transmission Grid
PublikacjaThe article discusses issues of reactive power compensation in transmission grids, with particular focus on the selection of compensator locations and basic parameters. Attention was focused on modern power electronics systems that ensure full automatic compensator adjustment to voltage or power criteria.
-
Comparative Evaluation of Multicoil Inductive Power Transfer Approaches Based on Z-source Network
PublikacjaThis paper describes comparative evaluation between wireless power transfer topologies with utilization of Z-source network. Paper describes components calculation method. List of open-loop, close-loop simulations were conducted to compare both topologies. Spectrum of signals is also researched.
-
Analysis of inductive power transfer systems for variable air gap and voltage supply frequency
PublikacjaThe paper describes an IPT system, by which electrical energy may be transmitted through a large air gap between coils without electrical connection. It presents theoretical and simulation analysis of IPT, which allows for supplying a receiver in the conditions of slow, in relation to the dynamics of power supply, changes in dimension of the air gap. The influence of frequency characteristics of the system on the possible selection...
-
Comparative Evaluation of Multicoil Inductive Power Transfer Approaches Based on Z-source Network
Publikacja -
Novel Inductive Power Transfer Approach Based on Z-Source Network with Compensation Circuit
Publikacja -
Structural Health Monitoring of Overhead Power Transmission Lines
PublikacjaStructural Health Monitoring (SHM) is a novel and continuously developing branch of science and technology that draws attention of scientists all over the world. It creates opportunities to detect, localize and identify structural damage of various types such as: line breakage, permissible sag, bolt loosening, fatigue cracking or insulator contamination. On the other hand the methods used to estimate the remaining operational...
-
Modified Inductive Multi-Coil Wireless Power Transfer Approach Based On Z-Source Network
PublikacjaThis article presents a non-conventional approach to a multi-coil wireless power transfer system based on a Z-source network. The novelty of the approach lies in the use of a Z-source as a voltage source for energy transmission through the wireless power transfer coils. The main advantage is in a reduced number of semiconductors. This paper provides the design approach, simulation and experimental study. Feasibility and possible...
-
The Issues of Reactive Power Compensation in High-voltage Transmission Lines
PublikacjaThis paper discusses the selection of compensation shunt reactors for a double-circuit 400 kV transmission line using the example of the newly built Elk Bis – Alytus transmission line. The analysis takes into account various conditions of the power system. The published results relate to voltage levels in steady states and during switching processes and short circuits.
-
The effect of the power transmission of the spindle on the position of the circular saw teeth
PublikacjaNa dokładność przecinania ma decydujący wpływ położenie ostrzy piły tarczowej. W pracy analizowano przyczyny i błędy połozenia ostrzy piły w stosunku do przedmiotu obrabianego spowodowane odkształceniem wrzeciona wywołanym przez siły skrawania i siły pochodzące od napędu.
-
Power and energy measurement problems in transmission line between Poland-Lithuania
PublikacjaThe paper discusses problem of power and energy metering in double circuit overhead transmission line. Considerations are based on example of transmission line connecting Polish substation Bis Elk and Lithuanian substation Alytus.
-
Fiber optic interface channels for united data and power supply transmission for neutral interaction application in signal transmission networks
Publikacja -
Damage Detection Strategies in Structural Health Monitoring of Overhead Power Transmission System
PublikacjaOverhead power transmission lines, their supporting towers, insulators and other elements create a highly distributed system that is vulnerable to damage. Typical damage scenarios cover cracking of foundation, breakage of insulators, loosening of rivets, as well as cracking and breakage of lines. Such scenarios may result from various factors: groundings, lightning strikes, floods, earthquakes, aeolian vibrations, conductors galloping,...
-
Feasibility Study GaN Transistors Application in the Novel Split-Coils Inductive Power Transfer System with T-Type Inverter
PublikacjaA promising solution for inductive power transfer and wireless charging is presented on the basis of a single-phase three-level T-type Neutral Point Clamped GaN-based inverter with two coupled transmitting coils. The article focuses on the feasibility study of GaN transistor application in the wireless power transfer system based on the T-type inverter on the primary side. An analysis of power losses in the main components of the...
-
Cross-border transmission line configuration influence on the electrical power and energy billing process
PublikacjaIn 2015 a connection between the Polish and Lithuanian power systems become fully operational. The connection consists of a 400 kV double circuit transmission line and a back-to-back HVDC substation located on the Lithuanian side. A magnetic couplings between the circuits of the transmission line cause that during power transmission a different values of active power losses are observed in both circuits. This situation may cause...
-
Reliability assessment of an OVH HV power line truss transmission tower subjected to seismic loading
PublikacjaThe study focuses on the reliability of a transmission tower OS24 ON150 + 10, an element of an OVH HV power line, under seismic loading. In order to describe the seismic force, the real-life recording of the horizontal component of the El Centro earthquake was adopted. The amplitude and the period of this excitation are assumed random, their variation is described by Weibull distribution. The possible space state of the phenomenon...
-
Multiservice Optical Fibre Local Area Networks For Data Transmission And Telemetry In The Electric Power Industry
Publikacja -
Magnetic and capacitive couplings influence on power losses in double circuit high voltage overhead transmission line
PublikacjaPurpose – The paper aims to discuss problems of power and energy losses in a double-circuit overhead transmission line. It was observed from energymeters’ readings, that in such a line, active power losses can be measured as “negative”. The “negative” active power losses appear when the active power injected to the circuit is lower than the active power received at the circuit end. The purpose of this paper is to explain this phenomenon. Theoretical...
-
Simulating Power Generation from Photovoltaics in the Polish Power System Based on Ground Meteorological Measurements—First Tests Based on Transmission System Operator Data
PublikacjaThe Polish power system is undergoing a slow process of transformation from coal to one that is renewables dominated. Although coal will remain a fundamental fuel in the coming years, the recent upsurge in installed capacity of photovoltaic (PV) systems should draw significant attention. Owning to the fact that the Polish Transmission System Operator recently published the PV hourly generation time series in this article, we aim...
-
Magnetic and capacitive couplings influence on power and energy measurement in double circuit high voltage overhead transmission line
PublikacjaThe paper discusses influence of magnetic and capacitive couplings on power and energy measurement in case of double circuit high voltage overhead transmission line. There are presented and discussed various factors influencing the power flow among the line‟s circuits. Mathematical model based calculations results are compared to the real transmission line measurements.
-
Low-Power Receivers for Wireless Capacitive Coupling Transmission in 3-D-Integrated Massively Parallel CMOS Imager
PublikacjaThe paper presents pixel receivers for massively parallel transmission of video signal between capacitive coupled integrated circuits (ICs). The receivers meet the key requirements for massively parallel transmission, namely low-power consumption below a single μW, small area of less than 205 μm2, high sensitivity better than 160 mV, and good immunity to crosstalk. The receivers were implemented and measured in a 3-D IC (two face-to-face...
-
Selection of C-Type Filters for Reactive Power Compensation and Filtration of Higher Harmonics Injected into the Transmission System by Arc Furnaces
PublikacjaThis article presents a method for selecting the elements of a C-type filter working with a conventional LC-type filter for compensating reactive power and filtering out higher harmonics generated by arc furnaces and ladle furnaces. The study was conducted in a steel mill supplied by a 110 kV transmission system, where higher harmonic currents and nonlinear loads were measured. A series of computer simulations were performed under...
-
Multicast Traffic Throughput Maximization through Joint Dynamic Modulation and Coding Schemes Assignment, and Transmission Power Control in Wireless Sensor Networks
Publikacja -
Attempt to a Video-Transmission Capability in MV Mine Cable Network Using BPL-PLC Technology
PublikacjaThis article presents and discusses the attempt to transmit video content using the BPL-PLC (Broadband over Power Line - Power Line Communication) technology. It includes simulation results of a specially developed digital transmitter and receiver, dedicated to a given predefined 6 kV mining power cable. The effect of two different transmission modes (2-7 MHz and 3-7.5 MHz) and two types of coupling (capacitive-inductive and induction-inductive),...
-
Subjective and Objective Quality Evaluation Study of BPL -PLC Wired Medium
PublikacjaThis paper presents results of research on the effectiveness of bi-directional voice transmission in a 6 kV mine cable network using BPL-PLC (Broadband over Power Line - Power Line Communication) technology. It concerns both emergency cable state (supply outage with cable shorted at both ends) and loaded with distorted current waveforms. The narrowband (0.5 MHz–15 MHz) and broadband (two different modes, frequency range of 3 MHz–7.5...
-
Quality Evaluation of Speech Transmission via Two-way BPL-PLC Voice Communication System in an Underground Mine
PublikacjaIn order to design a stable and reliable voice communication system, it is essential to know how many resources are necessary for conveying quality content. These parameters may include objective quality of service (QoS) metrics, such as: available bandwidth, bit error rate (BER), delay, latency as well as subjective quality of experience (QoE) related to user expectations. QoE is expressed as clarity of speech and the ability...
-
Subjective Quality Evaluation of Underground BPL-PLC Voice Communication System
PublikacjaDesigning a reliable voice transmission system is not a trivial task. Wired media, thanks to their resistance to mechanical damage, seem an ideal solution. The BPL-PLC (Broadband over Power Line – Power Line Communication) cable is resilient to electricity stoppage and partial damage of phase conductors. It maintains continuity of transmission in case of an emergency situation, including paramedic rescue operations. These features...
-
Compensation Topologies in IPT Systems: Standards, Requirements, Classification, Analysis, Comparison and Application
PublikacjaWireless power transfer devices are becoming more relevant and widespread. Therefore, an article is devoted to a review, analysis and comparison of compensation topologies for an inductive power transfer. A new classification of topologies is developed. A lot of attention is paid to the problems of the physical fundamentals of compensation work, standards, safety, and five main topology requirements. It is determined, that topologies...
-
BPL-PLC Voice Communication System for the Oil and Mining Industry
PublikacjaApplication of a high-efficiency voice communication systems based on broadband over power line-power line communication (BPL-PLC) technology in medium voltage networks, including hazardous areas (like the oil and mining industry), as a redundant mean of wired communication (apart from traditional fiber optics and electrical wires) can be beneficial. Due to the possibility of utilizing existing electrical infrastructure, it can...
-
TRANSFER OF ELECTRIC ENERGY [2023/24]
Kursy OnlineCourse content: Basic information on the structure of the power system, the major devices (components) for generation, transmission and distribution of electricity. Active and reactive power generation and their sources. Power supply networks. Tasks, structure, parameters. AC and DC transmission of electricity. Equivalent diagrams of the components of the power system. Steady state load flow calculation: currents, voltage,...
-
TRANSFER OF ELECTRIC ENERGY [2022/23]
Kursy OnlineCourse content: Basic information on the structure of the power system, the major devices (components) for generation, transmission and distribution of electricity. Active and reactive power generation and their sources. Power supply networks. Tasks, structure, parameters. AC and DC transmission of electricity. Equivalent diagrams of the components of the power system. Steady state load flow calculation: currents, voltage,...
-
A Low-Profile Metal-backed Dipole Loaded with Closely Coupled Arc-shaped Open Stubs for On-metal Tag Design with Wide Frequency Tuning Capability
PublikacjaThis research has presented a single-layer metal-backed dipole antenna, which consists of a feedline loaded with two pairs of closely-coupled arc-shaped open stubs, for designing a metal-mountable tag that features tuning capability over a wide range of frequency. Here, the stubs can generate sufficient inductive reactance for bringing down the tag resonant frequency tunable in both the regulated UHF RFID passbands (North American...
-
Miniaturized bandpass substrate integrated waveguide filter with frequency-dependent coupling realized using asymmetric GCPW discontinuity
PublikacjaAn asymmetric GCPW discontinuity is proposed to provide frequency-dependent coupling in microwave bandpass filters. Wider and narrow sections introduce, respectively, the capacitive and inductive component to the equivalent circuit representing coupling. By selecting the dimensions of the discontinuity and width of the inductive window in substrate integrated waveguide, an additional transmission zero can be introduced at prescribed...
-
Bandwidth-Controllable Third-Order Band Pass Filter Using Substrate Integrated Full- and Semi-Circular Cavities
PublikacjaThe article presents a novel circular substrate integrated waveguide (SIW) bandpass filter (BPF) with controllable bandwidth. The proposed BPF is configured using two microstrip feedlines, semi- circular SIW cavities, capacitive slots, and inductive vias. The circular cavity is bisected into two halves, with the two copies thereof being cascaded. Two bisected and cascaded structures obtained this way are subsequently connected...
-
Investigation of plasmon resonance in a silver nanoparticles
Dane BadawczeSilver nanostructures were prepared on borosilicate glass (Corning 1737F) substrates. Thin Ag films (1–9 nm thickness) were deposited using a table-top dc magnetron sputtering coater (EM SCD 500, Leica) in pure Ar plasma (argon, Air Products 99.999%). The Ag target was of 99.99% purity, the rate of layer deposition was about 0.4 nm·s−1, and the incident...
-
A Linear Phase Filter in Quadruplet Topology With Frequency-Dependent Couplings
PublikacjaThis letter presents a design of a linear phase microwave bandpass filter. The filter is composed of four resonators arranged in the quadruplet topology. Making the cross and one direct coupling dispersive gives additional design flexibility. The first advantage of using frequency-dependent couplings is the possibility to chose an arbitrary location of a pair of complex transmission zeros (TZs) in the s-domain. The second one is...
-
Krzysztof Nyka dr hab. inż.
OsobyKrzysztof Nyka, absolwent Wydziału Elektroniki Telekomunikacji i Informatyki Politechniki Gdańskiej (WETI PG), gdzie uzyskał tytuł magistra inżyniera (1986, telekomunikacja) stopień doktora nauk technicznych (2002, elektronika) i doktora habilitowanego (2020 automatyka, elektronika i elektrotechnika). Obecnie jest zatrudniony na stanowisku profesora uczelni w Katedrze Inżynierii Mikrofalowej i Antenowej WETI PG. Zainteresowania...
-
Plasmon resonance in a TiO2-Au NPs structures
Dane BadawczeInvestigated structures were deposited on a pre cleaned Corning 1737 glass substrates, which provided flat optical transmission characteristics and high transmission coefficient in a visible light range. Plasmonic nanostructures were formed as a result of thermal annealing. For gold films with thickness of 2.8 nm depiction a table-top dc magnetron sputtering...
-
Vehicle Dynamics - L-15/C-15/L-15/P-15, Design and Production Engineering, WIMiO, undergraduate studies, engineering studies, full-time (stationary) studies, 2021/2022, se06, (M:320383W0), summer semester 2023/2024
Kursy OnlineModuł przedmiotów wybieralnych, MiBM, I stopień, specjalność w j. angielskim: Design and Production Engineering (DaPE), semestr 6?, (przedmiot dla Chińczyków), Lecture: Throttle by tyred wheel: slip rolling, rolling with tyre strain, vertical and lateral surface reactions, traction, energetic looses, forces in contact path. Drugs of movement: rolling, air, gradient, inertia, cornering and towing. Forces ant torques acting to vehicle...
-
Poland’s energy dependence - economic context
Dane BadawczePoland does not have vast resources of non-renewable energy and no nuclear power plant, therefore the issue of the energy dependence of the state, which affects the level of energy security of the country, is an extremely important factor. It depends on both the volume of imports of energy raw materials and the policy of diversification of sources of...
-
Arsalan Muhammad Soomar Doctoral Student
OsobyHi, I'm Arsalan Muhammad Soomar, an Electrical Engineer. I received my Master's and Bachelor's Degree in the field of Electrical Engineering from Mehran University of Engineering and Technology, Jamshoro, Sindh, Pakistan. Currently enrolled as a Doctoral student at the Gdansk University of Technology, Gdansk, Poland. Also worked in Yellowlite. INC, Ohio as a Solar Design Engineer. HEADLINE Currently Enrolled as a Doctoral...
-
Accurate design of pseudoelliptic inline SIW filters with frequency-dependent couplings
PublikacjaThis paper presents an accurate synthesis method for inline SIW (Substrate Integrated Waveguide) generalized Chebyshev bandpass filters with frequency-dependent couplings. The technique is based on the synthesis of a coupling matrix that takes into account the impedance of the frequency-dependent stub. Thus, a loading effect compensation in adjacent resonators (via resonant frequency adjustment) and coupling elements (via coupling-value...
-
Przesył energii elektrycznej - potrzeby,progi i bariery
PublikacjaW artykule przeanalizowano stan aktualny i kierunki rozwoju krajowego systemu przesy ł owego w kontek ś cie potrzeb gospodarki krajowej. Przedstawiono znaczenie sieci przesy ł owych oraz rol ę operatorów systemu przesy ł owego i systemów dystrybucyjnych w sektorze energetycznym. Oceniono mo ż liwo ś ci rozwoju przy uwzgl ę dnieniu aktualnych prognoz zapotrzebowania na energi ę , wytyczono potencjalne...
-
Zastosowanie modułu symulacji dynamicznej programu CAD w analizie układu napędowego elektronarzędzia
PublikacjaW referacie przedstawiono analizę mechanicznego układu przeniesienia napędu elektronarzędzia (wyrzynarki elektrycznej) przy zastosowaniu Modułu Symulacji Dynamicznej (MSD) programu Autodesk Inventor (AI). Opracowano modele 3D poszczególnych części elektronarzędzia i połączono je przy zachowaniu tzw. kinematyki odwrotnej. Przeprowadzono analizę wpływu poszczególnych węzłów kinetycznych na przebieg momentu na wale silnika elektrycznego....
-
Koncepcja platformy wymiany informacji o incydentach cyberbezpieczeństwa dla krajowego systemu elektroenergetycznego
PublikacjaArtykuł opisuje wybrane zagadnienia związane z cyberbezpieczeństwem w sektorze elektroenergetyki. Jednym z elementów zapewniania bezpieczeństwa sieci elektro-energetycznej jest efektywna wymiana informacji o incydentach bezpieczeństwa. W jej ramach wszystkie zaangażowane podmioty systemu elektroenergetycznego, tj.: elektrownie, operatorzy systemów przesyłowych, operatorzy systemów dystrybucyjnych, dostawcy rozwiązań bezpieczeństwa,...
-
Zastosowanie specjalnego uziemienia żył powrotnych w liniach kablowych SN
PublikacjaW artykule porównano metody uziemiania żył powrotnych kabli średniego napięcia. Głównym kryterium oceny poszczególnych rozwiązań było ograniczenie strat w przesyle energii elektrycznej oraz zapewnienie ochrony przeciwprzepięciowej osłon kabli. Na podstawie symulacji kabli zamodelowanych w programie CYMCAP i otrzymanych wyników obciążalności prądowej i strat w linii zaprezentowano metodę krzyżowania żył powrotnych (CB – cross-bonding...
-
KRYTERIA STOSOWANE W WIELOKRYTERIALNYM PLANOWANIU ROZWOJU SYSTEMU ELEKTROENERGETYCZNEGO
PublikacjaProblematyka planowania rozwoju systemów elektroenergetycznych jest zagadnieniem często podejmowanym w badaniach optymalizacyjnych ze względu na wagę i zasięg problemu. Rozwój techniki komputerowej pozwolił na połączenie tematyki optymalizacji struktury wytwarzania i planowania sieci elektroenergetycznej, co jest zagadnieniem wielowątkowym oraz wielowymiarowym. W prezentowanym artykule przedstawiono kryteria stosowane w analizach...
-
WARUNKI REZONANSOWE W WĘŹLE Z KOMPENSATOREM SVC
PublikacjaInstalowanie kompensatorów statycznych w sieciach rozdzielczych i przesyłowych służy poprawie profili napięciowych. Kompensatory jako źródła mocy biernej zwiększają stabilność napięciową systemu. Pozwalają także na szybszą odbudowę systemu w przypadku awarii napięciowej. W artykule zaprezentowano wpływ struktury i wysterowania układu SVC na zmianę impedancji w układzie zasilania. Ma to bezpośredni wpływ na częstotliwości, przy...