Wyszukiwarka
Filtry
wszystkich: 1904
-
Katalog
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: LOAD EQUIVALENCY FACTOR
-
Impact of overloaded vehicles on load equivalency factors and service period of flexible pavements
PublikacjaOverloaded vehicles occur less frequently in comparison to properly loaded vehicles but due to their greater potential to cause damage they significantly contribute to the distress of pavement structure. As the studies show, the phenomena of vehicles overloading intensifies when the control of traffic is poor and the average percentage of overloaded vehicles on analyzed roads varies from 6% to 23%. The main goal of the ar-ticle...
-
Determination of Vehicles Load Equivalency Factors for Polish Catalogue of Typical Flexible and Semi-rigid Pavement Structures
PublikacjaThe new Polish Catalog of Typical Flexible and Semi-rigid Pavement Structures was introduced to use in practice in 2014. Much of works were focused on actualization of vehicles load equivalency factors. For this purpose data delivered from weigh-inmotion were analyzed. Four methods of determination of load equivalency factors for pavement structure design were compared. The analysis showed that fourth power equation, AASHTO 1993...
-
Analysis of effect of overloaded vehicles on fatigue life of flexible pavements based on weigh in motion (WIM) data
PublikacjaOverloaded vehicles have a significant impact on pavement fatigue life and distress. As the studies show, the phenomena intensify when the control of traffic is poor. The paper presents the results of the research including analysis of weigh in motion data from eight stations and analysis of asphalt pavement fatigue caused by mixed traffic. Distributions of vehicles axles load including the multiple axles effects are presented....
-
Analysis of pavement structure sensitivity to passage of oversized heavy duty vehicle in terms of bearing capacity
PublikacjaOversized heavy duty vehicles occur in traffic very rarely but they reach extremely high weights, even up to 800 tonne. The detrimental impact of these vehicles on pavement structure is much higher than in case of commercial vehicles that comprise typical traffic, thus it is necessary to assess the sensitivity of pavement structure to passage of oversized vehicles. The paper presents results of sample calculations of load equivalency factor...
-
Effect of Overloaded Vehicles on Whole Life Cycle Cost of Flexible Pavements
PublikacjaThe phenomenon of vehicle overloading—illegal exceeding of maximum legal weight of vehicles, is a serious problem both in developing and developed countries around the world. Overloaded vehicles occur less frequently in comparison to properly loaded vehicles but due to their greater potential to cause damage they significantly contribute to distress of pavement structure. As studies show, the number of overloaded vehicles increases...
-
Stateczność samopodnoszących pełnomorskich platform wiertniczych w fazie eksploatacji
PublikacjaWspółczynnik bezpieczeństwa platformy Petrobaltic na moment obrotowy (stateczność ogólna) oszacowany przy założeniu, że konstrukcja jest traktowana jako układ słupów połączonych sztywnym pokładem, z korekcją efektów drugiego rzędu. Przemieszczenie poziome pokładu platformy wyznaczone, stosując odpowiedni model MES. Siła krytyczna nogi obliczona przy założeniu jej utwierdzenia w dnie morza. Wpływ odchyłki od idealnej geometrii rur...
-
Determination of equivalent axle load factors with the use of strain energy of distortion
PublikacjaThe paper proposes a new method for calculation of equivalent axle load factors based on the analysis of strain energy of distortion induced in road pavements by traffic loads. The main advantage of the method is the more accurate calculation of the effects of multiple axles and super single versus dual tyres. The methodconsiders the location of critical points, at which strain energy of distortion reaches extreme values. When...
-
СИЛОВОЙ ПРЕОБРАЗОВАТЕЛЬ С АКТИВНЫМ ПОДАВЛЕНИЕМ ВЫСШИХ ГАРМОНИК ДЛЯ СИСТЕМ ЭЛЕКТРОСНАБЖЕНИЯ ЛЕТАТЕЛЬНЫХ АППАРАТОВ (Power converter with active suppression of higher harmonics for aircraft power supply systems)
PublikacjaПредставлены два алгоритма активной фильтрации для силового преобразователя с активным подавлением высших гармоник. Первый алгоритм основан на дискретном преобразовании Фурье: посредством синтезированной системы управления инвертированные измеренные высшие гармоники напряжения поступают на вход инвертора. Второй метод управления основан на алгоритме с использованием принципов самообучения, что значительно снижает потребность в...
-
Wpływ równości nawierzchni i dynamicznego oddziaływania pojazdów ciężkich na trwałość zmęczeniową nawierzchni podatnych
PublikacjaPodczas ruchu pojazdu obserwuje się odchylenia nacisków osi pojazdów od nacisku statycznego, co jest spowodowane nierównościami nawierzchni. Dynamiczne obciążenia pojazdów w większym stopniu wytężają konstrukcję nawierzchni drogowej. Rozkład obciążeń dynamicznych ma kształt rozkładu normalnego i jest opisywany poprzez obciążenie statyczne oraz wskaźniki dynamiczne DI lub DLC. Wraz z pogorszeniem równości i zwiększeniem prędkości...
-
The experimental results of diesel fuel spray with marine engine injector
Dane BadawczeThe data set presents the measurement of the diesel fuel spray from with marine engine injector. The main target presents results is a study of the time course of macro parameters (spray tip penetration, spray cone angle) of fuel spray in the cylinder of marine diesel engine. The impact of ambient conditions and the geometrical parameters of the injector...
-
The flux compression generator load parameters selection
PublikacjaComputer simulation results of the flux compression generator (FCG) loaded with an inductor has been presented in this paper. Simulation research has been performed in order to select the parameters of FCG load coil properly. The influence of the load inductance and resistance on the current gain factor and the magnetic field energy accumulated in a load coil has been investigated.
-
A modified static equivalency method for roll-on/roll-off vessels
PublikacjaPrzedstawiono zmodyfikowaną metodę statycznej równoważności dla statków ro-ro, opartą na wypiętrzaniu się wody na pokładzie samochodowym w wypadku wystąpienia otworu w burcie, do oceny bezpieczeństwa statku.
-
Charakterystyka eksploatacyjna pomp ciepła zainstalowanych w oczyszczalni ścieków
PublikacjaW artykule przedstawiono charakterystykę eksploatacyjną sprężarkowych pomp ciepła zainstalowanych w oczyszczalni komunalnej i wykorzystujących ścieki oczyszczone jako dolne źródło ciepła. Zastosowanie ścieków oczyszczonych jest uzasadnione ich dostępnością oraz stosunkowo wysoką temperaturą (10-25°C). Prawidłowa eksploatacja układu wymaga zastosowania pośredniego obiegu parowacza oraz regularnych zabiegów czyszczenia wymiennika...
-
Stability and load bearing capacity of a truss with elastic braces
PublikacjaThe present paper is devoted to the numerical and experimental investigations of stability of a truss stiffened by elastic braces. The model of a real roof truss scaled by factor ¼ was investigated. In the research the linear buckling and non-linear static analysis of the truss shell and beam model with geometric and material non-linearity is presented. The initial imperfections were assumed in the form of the first buckling mode....
-
Load function walking pedestrian on the footbridge.
PublikacjaModern foot bridges are more and more sensitive to variable load created by moving pedestrians. These are several reasons for that. Quickly growing up road infrastructure forces us to build foot bridges just to reconnect one piece of land, separated now by the new road or railway. These bridges are lightweight because the only live load acting on them comes from pedestrians.The paper focuses on the definition of human induces dynamic...
-
Verification of baffle factor for straight pipe flow
PublikacjaDuring the water disinfection devices designing, it is often assumed that the baffle factor for a straight pipe reactors is equal to one. It would be possible only for the plug flow, which is a simplified model of the flow and does not appear in real situations. The paper contains an equation which enables calculation of the real value of the baffle factor for the pipe flow.
-
Within- and between-person factor structure of the Oldenburg Burnout Inventory: Analysis of a diary study using multilevel confirmatory factor analysis
PublikacjaThe study examined the factor structure of burnout, as measured with the Oldenburg Burnout Inventory. The participants were 235 employees of a public administration agency who assessed their burnout online for 10 consecutive working days. Two models were tested with multilevel confirmatory factor analysis, assuming the same one or two-factor structure at the within- and between-person levels. Both models showed a reasonable fit...
-
Share of the wage factor in national income – selected aspects
PublikacjaThe aim of this study is to examine changes in the share of the wage factor in national income, in selected EU countries against labour productivity and investment rates reflecting changes in capital-labour relations, indicated by researchers as determinants of change of the share of the wage factor in national income. The scope of the study includes a review of literature devoted to the issue of wage factor share in national income...
-
Ice Load Characteristics on Floating Photovoltaic Platform
PublikacjaNowadays, based upon human needs and preferring perpetual types of energy, photovoltaic system (PV) is a suitable alternative and more frequently used in northern countries, which are recently more attracted by solar power. The new floating type of the structure is installed in the water bodies instead of land. One of the main elements in floating photovoltaic structures is the forces imposed on the panels. In the northern regions,...
-
How much is Impact Factor worth?
PublikacjaThe purpose of this work is to present an aspect of counting citations, which is correlated to the Impact Factor, very important for journals in scientific communication, and provides information about the position of a scientific journal in a particular research area. Sometimes citations don’t count in a research output, e.g. if an article is published in a predatory journal. Those journals ...
-
System load impact on VRRP advertisements delay
PublikacjaThe aim of the paper is to show how system load can affect network tasks (especially VRRP advertising depending on factors such as kernel schedu-ler [3] version, kernel settings and load priority. Two versions of the Linux kernel will be used: 2.6.22 (with "O(1) scheduler) and 2.6.23 (with "CFS" scheduler). "vrrpd" version 0.4 is used as an VRRP protocol implementation.
-
A method of nonlinearities of transformer no-load characteristic modelling
PublikacjaA way in which changes of the no-load characteristic are taken into account in the mathematical model of the transformer is presented. Changes of saturation within core of transformer are presented as a combined non-linear flux curve. Analysis of magnetization of the transformer core and simulation of no-load state for distribution transformer of 30 kVA power rating and 15.75/0.4 kV/kV (especially supplying VLV) transformation...
-
Load-settlement characteristics of piles working in a group
PublikacjaLoad-settlement characteristic (Q-s) of an axially loaded pile can be empirically determined from a static pile load test or on the basis of calculations using, e.g. transfer functions or numerical methods (FEM). The transfer functions method usually rely on empirical data, i.e. the function parameters are determined on the basis of numerous pile test results. Thus this method takes into account pile installation technology and...
-
Scaling of numbers in residue arithmetic with the flexible selection of scaling factor
PublikacjaA scaling technique of numbers in resudue arithmetic with the flexible selection of the scaling factor is presented. The required scaling factor can be selected from the set of moduli products of the Residue Number System (RNS) base. By permutation of moduli of the number system base it is possible to create many auxilliary Mixed-Radix Systems associated with the given RNS with respect to the base, but they have different sets...
-
Estimation of Rician K-factor Values in Urban Terrain
PublikacjaThis paper presents results of Rician K-factor estimation from CDMA2000 downlink signals recorded in the area of medium city. Signal and data processing methods used to estimate fading parameters are also briefly described.
-
Stability and load bearing capacity of a braced truss under upward wind loading
PublikacjaThe paper is focused on the numerical and experimental investigation of stability of a steel truss under upward wind loading. The structure was stiffened by elastic braces situated at the top and bottom chord. Usually the lateral (translational) brace stiffness is considered. However, the rotational stiffness of braces caused by interaction between torsional stiffness of the truss top chord and bending stiffness of the roof elements...
-
Stability and load bearing capacity of a braced truss under upward wind loading
PublikacjaThe paper is focused on the numerical and experimental investigation of stability of a steel truss under upward wind loading. The structure was stiffened by elastic braces situated at the top and bottom chord. Usually the lateral (translational) brace stiffness is considered. However, the rotational stiffness of braces caused by interaction between torsional stiffness of the truss top chord and bending stiffness of the roof elements...
-
Korzyści z zastosowania układów Load Sensing
PublikacjaW artykule porównano układy Load Sensing I i II rodzaju z układem z dwudrogowym regulatorem przepływu. Dokonano oceny mocy traconych oraz korzyści stosowania układów LS w stosunku do tradycyjnych rozwiązań
-
Image as a key factor of brand value at social media
PublikacjaThe paper aims to investigate the relationship between social media presence and activities and brand value for the most valuable Global Brands 2012 (Interbrandt 2013). Social media communication is an innovative way of communication. Brand value is a key performance indicator of brand strategy for managers. Brand and category image realized to be the key factor of investigated relation.
-
The Influence of LED Lighting Sources on the Nature of Power Factor
PublikacjaThis article presents measurements of electric power absorbed by a newly built facility for office and scientific research activities. These measurements highlighted the need for compensation of capacitive reactive power—not predicted by the designer—due to the vast use of LED lighting in the facility. The article also describes a reactive power compensation system, designed on the basis of the above-mentioned measurements, and...
-
Underfrequency Load Shedding: An Innovative Algorithm Based on Fuzzy Logic
PublikacjaIn contemporary power systems, the load shedding schemes are typically based on disconnecting a pre-specified amount of load after the frequency drops below a predetermined value. The actual conditions at the time of disturbance may largely dier from the assumptions, which can lead to non-optimal or ineective operation of the load shedding scheme. For many years, increasing the eectiveness of the underfrequency load shedding (UFLS)...
-
Analysis of the Impact of Charging Electric Cars on the Power System Load
PublikacjaThe paper presents ways of integrating electric cars with the power system. In connection with this, daily load curves in the average working day have been developed in the G2V (Grid-to-Vehicle) and V2G (Vehicle-to-Grid) variants. The G2V solution consists in unidirectional energy flow from the power system to a vehicle’s battery. The V2G solution consists in bi-directional energy exchange between the power system and electric...
-
Anticancer imidazoacridinone C-1311 inhibits hypoxia-inducible factor-1α (HIF-1α), vascular endothelial growth factor (VEGF) and angiogenesis
PublikacjaAntitumor imidazoacridinone C-1311 is a DNA-reactive topoisomerase II and FLT3 receptor tyrosine kinase inhibitor. Here, we demonstrate the mechanism of C-1311 inhibitory action on novel targets: hypoxia-inducible factor-1α (HIF-1α), vascular-endothelial growth factor (VEGF), and angiogenesis. In a cell-free system, C-1311 prevented HIF-1α binding to an oligonucleotide encompassing a canonical hypoxia-responsive element (HRE),...
-
Displacement measurements during load testing of railway arch bridge
PublikacjaThe paper discusses issues concerning load tests carried out on a twin-track, arch railway bridge over the Martwa Wisla river in Gdansk. Currently, it is the bridge with the longest span in its class in Poland. The load-bearing structure consists of three no-hinge arches and an orthotropic deck suspended from them. The studies of the structure assumed the performing of static and dynamic tests. The paper presents the method for...
-
Correlation between natural frequencies and buckling load in a stiffened shell
PublikacjaThe paper deals with correlation between natural frequencies and buckling load of a stiffened shell composed of corrugated sheets and vertical stiffeners (columns). The simplified shell segment represents the buckling behaviour of a whole silo with sparsely distributed columns. The paper covers variants of linear buckling anal-yses, dynamic eigenvalue analyses and geometrically non-linear analyses of a segment modelled with shell...
-
Load Testing of GFRP Composite U-Shape Footbridge
PublikacjaThe paper presents the scope of load tests carried out on an innovative shell composite footbridge. The tested footbridge was manufactured in one production cycle and has no components made from materials other than GFRP laminates and PET foam. The load tests, performed on a 14-m long structure, were the final stage of a research program in the Fobridge project carried out in cooperation with: Gdańsk University of Technology (leader),...
-
High load capacity spur gears with conchoidal path of contact
PublikacjaThe present study is devoted to investigation of spur gears with a conchoidal path of contact and a convex-convex contact between teeth. The load capacity and energy efficiency were evaluated using both theoretical and experimental approaches. The theoretical analysis showed that the conchoidal gear pairs are 5–21% stronger in terms of contact stress and have similar energy efficiency as compared to the involute gear pairs of the...
-
Heuristic scheduling algorithms for uniform load of computer system
PublikacjaW pracy zaprezentowano opracowany heurystyczny algorytm szeregowania zadań UNILO (ang. UNIform LOad - jednakowe obciążenie), umożliwiający redukcję całkowitego zapotrzebowania na moc obliczeniową systemu komputerowego bez pogarszania jego wydajności. Algorytm ten realizuje takie przydzielenie zadań obliczeniowych do poszczególnych jednostek (procesorów), aby zapewnić ich jednakowe obciążenie. Opracowany algorytm został zweryfikowany...
-
INFLUENCE OF LOAD AND INFLATION PRESSURE ON THE TYRE ROLLING RESISTANCE
PublikacjaTyre load and inflation pressure are important factors controlling rolling resistance of road vehicles. The article presents results obtained in the Technical University of Gdańsk during laboratory and road measurements of different car tyres rolling on different pavements. The knowledge of rolling resistance characteristics is important for modelling car dynamics as well as fuel consumption. It is also necessary to establish proper...
-
The Influence of External Load on the Performance of Microbial Fuel Cells
PublikacjaIn this work, the effect of the external load on the current and power generation, as well as on the pollutant removal by microbial fuel cells (MFCs), has been studied by step-wise modifying the external load. The load changes included a direct scan, in which the external resistance was increased from 120 Ω to 3300 Ω, and a subsequent reverse scan, in which the external resistance was decreased back to 120 Ω. The reduction in the...
-
Developing the s factor
PublikacjaWzory IMO na mnożnik s (p-wo przetrwania statku z zatopionym przedziałem) abstrahują od czasu przetrwania, jak i falowania. Pokazano związek 'pierwotnego' mnożnika s z czasem przetwania na danym falowaniu oraz pokazano w jaki sposób przetransformować mnożnik s odpowiadający półgodzinnym doświadczeniom przewracania statku na mnożnik odpowiadający dłuższym przebiegom doświadczeń. Wydłużenie czasu doświadczeń nie ma drastycznego wpływu....
-
Biocompatibility and Bioactivity of Load-Bearing Metallic Implants
PublikacjaThe main objective of here presented research is to develop the titanium (Ti) alloy base composite materials possessing better biocompatibility, longer lifetime and bioactivity behaviour for load-bearing implants, e.g. hip joint and knee joint endoprosthesis. The development of such materials is performed through: modeling the material behaviour in biological environment in long time and developing of new procedures for such evaluation;...
-
Diagnostic Analysis of Exhaust Gas with A Quick-Changing Temperature from a Marine Diesel Engine Part II / Two Factor Analysis
PublikacjaThe article presents a continuation of research carried out to determine the effect of input parameters (changes in engine structure parameters) on selected output parameters (diagnostic measures), based on quickly changing exhaust gas temperature. A method of determining the simultaneous influence of two input factors (the structure parameter and the engine load) on one output factor was presented, as well as an evaluation...
-
Tissue Factor and Tissue Factor Pathway Inhibitor in Chronically Inflamed Gallbladder Mucosa
Publikacja -
Static load test on concrete pile – instrumentation and results interpretation
PublikacjaFor some time (since 8-10 years in Poland) a special static load tests on instrumented piles are carried out. Such studies are usually of a scientific nature and provide detailed quantitative data on the load transfer into the ground and characteristics of particular soil layers interaction with a pile shaft and pile base. Deep knowledge about the pile-subsoil interaction can be applied for a various design purposes, e.g. numerical...
-
Load testing of a suspended footbridge in Radom (Poland)
PublikacjaThe footbridge in Radom is a suspended bridge of an interesting architectural form. The structure was de-signed for 4 kN/m2 of crowd loading. Dynamic calculations were not included in the design. The structure’s acceptance tests took place on the 14th of October 2016. The behaviour of the footbridge in static testing met the expectations. Unfortunately, as a result of dynamic tests, dangerous behaviour of the footbridge was revealed....
-
Experimental Study of Dapped-End Beams Subjected to Inclined Load
PublikacjaThis paper presents the results of an experimental investigation of the reinforced concrete (RC) dapped-end beams loaded with inclined forces, compared to identical ones loaded with vertical forces only. Such a load may occur in, for example, Gerber's joints or in dapped-end beams supported on corbels, where the vertical gravitation force is additionally completed with horizontal forces caused by temperature differences, shrinking,...
-
Discussion - Experimental study of dapped–end beams subjected to inclined load
PublikacjaDiscussion - Experimental study of dapped–end beams subjected to inclined load
-
Consideration of dynamic loads in the determination of axle load spectra for pavement design
PublikacjaAxle load spectra constitute a crucial part of the data for pavement design and pavement distress analysis. Typically, axle load spectra represent static load from vehicles and do not include dynamic loads generated by vehicles in motion. While dynamic loads can significantly contribute to faster pavement distress, this fact is mostly omitted in pavement design methods. The paper presents a methodology for consideration of dynamic...
-
On the synthesis of coupled-lossy resonator filters with unloaded quality factor control
PublikacjaA technique for fast synthesis of coupling matrix low-pass prototypes of generalized Chebyshev bandpass filters with lossy resonators is presented in this paper. The coupling matrix is found by solving a nonlinear least squares problem based on zeros and poles of filter's transfer functions. Additional constraints are introduced that allow one to control the level of unloaded quality factor of resonators.