Wyniki wyszukiwania dla: PROTON EXCHANGE MEMBRANE FUEL CELL
-
Dynamic characteristics of the proton exchange membrane fuel cell module
PublikacjaThe paper describes a fuel cell based system and its performance. The system is based on two fuel cell units, DC/DC converter, DC/AC inverter, microprocessor control unit, load unit, bottled hydrogen supply system and a set of measurement instruments. In the study presented in the paper a dynamic response of the proton exchange membrane (PEM) fuel cell system to unit step change load as well as to periodical load changing cycles...
-
The impedance of hydrogen oxidation reaction in a proton exchange membrane fuel cell in the presence of carbon monoxide in hydrogen stream
PublikacjaEvaluation of performance of a proton exchange membrane fuel cell, which is affected by carbon monoxide that pollutes the hydrogen stream, was presented. This influence was studied for carbon monoxide concentration of 125–325 ppb, which are close to values specified in ISO 14687:2019 standard. Performed studies provided crucial information for further development of fuel cell as an energy source for automotive application. Impedance...
-
An integral-differential method for impedance determination of the hydrogen oxidation process in the presence of carbon monoxide in the proton exchange membrane fuel cell
PublikacjaThe impedance of a proton exchange membrane fuel cell powered by hydrogen contaminated with carbon monoxide, ranging from 150 to 300 ppb, is measured and discussed. The tested range of CO concentration complied with the fuel standard specified in the ISO standards. Studies of influence of CO contamination on operation of PEMFC are crucial for further development and commercialization of fuel cells for automotive applications. Based...
-
The impact of air humidity on the operation of proton exchange membrane fuel cells determined using dynamic electrochemical impedance spectroscopy
PublikacjaThis paper describes the changes in the fuel cell impedance across a range of current loads and humidity changes. The changes of each equivalent circuit parameters representing specific processes occurring in fuel cells, as a function of humidity and current changes, were determined. Within the combined scope of current and humidity, the optimal working conditions of the cells were determined, corresponding to the lowest impedance...
-
Influence of temperature and nitrogen pressure on the test without active gases for high-temperature proton exchange membrane fuel cells
PublikacjaHigh-Temperature Proton-Exchange Membrane Fuel Cells (HT-PEMFCs) are a candidate for electrical energy supply devices in more and more applications. Most notably in the aeronautic industry. Before any use, an HT-PEMFC is preheated and after that supplied with its active gases. Only at this state, the diagnostics can be performed. A method of testing not requiring a complete start-up would be beneficial for many reasons. This article...
-
Are Radicals Formed During Anion-Exchange Membrane Fuel Cell Operation?
Publikacja -
Chapter 4. Electricity generation from glucose microbial fuel cell
PublikacjaThe microbial fuel cell was constructed to generate electricity with simultaneous digestion of a glucose fuel by a bacterial biofilm. The decomposition of glucose resulted in releasing of electrons to an anode and to production of some by-products, e.g. metane or organic acids. It was found that maximum electric power density strongly depended on the proton transport through the proton exchange membrane seperating the anolyte and...
-
Local atomic order in low Pt-content nanocatalysts investigated in situ by XAS
PublikacjaThe unique features of X-ray absorption spectroscopy allow investigations of nanosized catalysts for fuel cells under working conditions. We present the results of an experiment carried out on a low Pt content electrocatalyst supported by a mesoporous heteropolyacid salt and used at the cathode of a proton exchange membrane fuel cell (PEMFC). The analysis of the EXAFS signal at the Pt L3-edge indicates that upon operating the fuel...
-
Visualization of the surface of the Nafion membrane
Dane BadawczeFuel cells use the chemical energy of hydrogen or other fuels to produce electricity. If the fuel is hydrogen, the only products are electricity, water and heat. Fuel cells are unique in the variety of their potential applications, they can use a wide variety of fuels. They are also highly scalable devices that can power both cars and mobile phones....
-
Structural change of carbon supported Pt nanocatalyst subjected to a step-like potential cycling in PEM FC
PublikacjaIn this paper we present detailed X-ray absorption fine structure (XAFS), X-ray diffraction (XRD) and transmission electron microscopy (TEM) investigations of the changes in the local geometric and electronic structure of Pt nanoparticles used as a cathode catalyst in proton exchange membrane fuel cell (PEMFC), working under controlled potential cycling conditions.
-
A XAS study of a highly diluted Pt electrocatalyst operating in PEM fuel cells
PublikacjaWe present an X-ray absorption spectroscopy (XAS) study of a low Pt content catalyst layer(Pt loading 0.1 mg c2) operating at the cathode of a proton exchange membrane fuel cell(PEMFC). This catalyst is based on the use of a mesoporous inorganic matrix as a support forthe catalyst Pt nanoparticles. Due to the high Pt dilution, in situ measurements of itsstructural properties by XAS are challenging and suitable experimental strategies...
-
Kazimierz Darowicki prof. dr hab. inż.
OsobyStudia wyższe ukończyłem w czerwcu 1981 roku po zdaniu egzaminu dyplomowego i obronie pracy magisterskiej. Opiekunem pracy magisterskiej był dr hab. inż. Tadeusz Szauer. W roku 1991, 27 listopada uzyskałem stopień naukowy broniąc pracę doktorską zatytułowaną „Symulacyjna i korelacyjna analiza widm immitancyjnych inhibitowanej reakcji elektrodowej”. Promotorem pracy był prof. dr hab. inż. Józef Kubicki (Wydział Chemiczny...
-
Optimization of the Relative Humidity of Reactant Gases in Hydrogen Fuel Cells Using Dynamic Impedance Measurements
PublikacjaWater management is a key factor affecting the efficiency of proton exchange membrane fuel cells (PEMFCs). The currently used monitoring methods of PEMFCs provide limited information about which processes or components that humidity has a significant impact upon. Herein, we propose the use of a novel approach of impedance measurements using a multi-sinusoidal perturbation signal, which enables impedance measurements under dynamic...
-
Assessment of Fuel Cells’ State of Health by Low-Frequency Noise Measurements
PublikacjaWe proposed applying low-frequency (flicker) noise in proton-exchange membrane fuel cells under selected loads to assess their state of health. The measurement set-up comprised a precise data acquisition board and was able to record the DC voltage and its random component at the output. The set-up estimated the voltage noise power spectral density at frequencies up to a few hundred mHz. We observed the evolution of the electrical...
-
Fabrication of the cross-linked PVA/TiO2/C nanocomposite membrane for alkaline direct methanol fuel cells
PublikacjaA crosslinked Poly(vinyl alcohol) based composite membrane was developed through a phase inversion process for use in alkaline direct methanol fuel cells (ADMFCs). The titanium dioxide (TiO2) and carbon nanoparticles (NPs) have been incorporated into the PVA polymer matrix to improve the mechanical and thermal properties. The membrane samples were further modified with maleic acid, a carboxylic acid acting as the cross-linker,...
-
Microstructural Design of Ba0.5La0.5Co0.5Fe0.5O3 Perovskite Ceramics
PublikacjaBa0.5La0.5Co0.5Fe0.5O3 was synthesized in the solid-state reaction route. The influence of ball milling parameters (such as milling media size, angular velocity, and time), pelletizing pressure, and annealing parameters on the microstructure was studied. The grain size distribution and density or specific surface area changes were investigated in each approach while the individual parameters were changed. The evaluation of BLCF...
-
Piotr Jasiński prof. dr hab. inż.
OsobyPiotr Jasinski obtained MSc in electronics in 1992 from the Gdansk University of Technology (GUT), Poland. Working at GUT, he received PhD in 2000 and DSc in 2009. Between 2001 and 2004 Post Doctoral Fellow at Missouri University of Science and Technology, while between 2008 and 2010 an Assistant Research Professor. Currently is an Associate Professor at Gdansk University of Technology working in the field of electronics, biomedical...
-
Performance of a single layer fuel cell based on a mixed proton-electron conducting composite
PublikacjaMany of the challenges in solid oxide fuel cell technology stem from chemical and mechanical incompatibilities between the anode, cathode and electrolyte materials. Numerous attempts have been made to identify compatible materials. Here, these challenges are circumvented by the introduction of a working single layer fuel cell, fabricated from a composite of proton conducting BaCe0.6Zr0.2Y0.2O3-δ and a mixture of semiconducting...
-
Synthesis and Testing of BCZY/LNZ Mixed Proton–electron Conducting Composites for Fuel Cell Applications
PublikacjaA composite of BaCe0.6Zr0.2Y0.2O3–δ and Li2O:NiO:ZnO was investigated for fuel cell applications. The composite was successfully synthesized and its phase stability was confirmed at temperatures up to 900 °C. The influence of sintering and pressing aids on density was also investigated. Electrical properties were measured. DC electrical conductivity was about 8•10-4 S/m at 845 K. Open circuit voltage measurements in wet hydrogen...
-
Performance and Stability in H2S of SrFe0.75Mo0.25O3-δ as Electrode in Proton Ceramic Fuel Cells
PublikacjaThe H2S-tolerance of SrFe0.75Mo0.25O3-δ (SFM) electrodes has been investigated in symmetric proton ceramic fuel cells (PCFC) with BaZr0.8Ce0.1Y0.1O3-δ (BZCY81) electrolyte. The ionic conductivity of the electrolyte under wet reducing conditions was found to be insignificantly affected in the presence of up to 5000 ppm H2S. The fuel cell exhibited an OCV of about 0.9 V at 700 °C, which dropped to about 0.6 V and 0.4 V upon exposure...
-
Polysaccharide nanocomposites in wastewater treatment: A review
PublikacjaIn modern times, wastewater treatment is vital due to increased water contamination arising from pollutants such as nutrients, pathogens, heavy metals, and pharmaceutical residues. Polysaccharides (PSAs) are natural, renewable, and non-toxic biopolymers used in wastewater treatment in the field of gas separation, liquid filtration, adsorption processes, pervaporation, and proton exchange membranes. Since addition of nanoparticles...
-
Impedance monitoring of fuel cell stacks
PublikacjaThis paper presents an innovative, electrochemical impedance method for monitoring of electrochemical behaviour of a multi-cell, direct methanol fuel cell (DMFC) device. This method not only provides classical voltage changes at successive cells but also allows their detailed impedance behaviour to be presented. Impedance characteristics of individual cells within a fuel cell stack (depending on actual operating conditions) are...
-
Operando EPR Study of Radical Formation in Anion-Exchange Membrane Fuel Cells
Publikacja -
Degradation of xylose using a microbial fuel cell
PublikacjaIt is generally known, that many kind of microorganisms are capable of using carbohydrates as a source of carbon and energy in an environment. The biodegradation process of monosaccharides from pentoses (in this case- racemic mixture of D - and L – xylose) is an immense opportunity for an entire reduction of biological contamination to neutral compounds through MFC. The process is occurred in a single-chamber MFC, which is contained...
-
Evolution of the nanostructure of Pt and Pt–Co polymer electrolyte membrane fuel cell electrocatalysts at successive degradation stages probed by X-ray photoemission
PublikacjaWe present a set of XPS (X-ray photoemission spectroscopy) measurements and detailed data-analysis of electrodes for polymer electrolyte membrane fuel cell (PEMFC) based on carbon supported catalysts (Pt and Pt–Co) subjected to a step-like potential cycling (accelerated degradation test). The results of the measurements complete and corroborate parallel TEM (transmission electron microscopy), XRD (X-ray diffraction) and XAS (X-ray...
-
Impedance Measurement and Selection of Electrochemical Equivalent Circuit of a Working PEM Fuel Cell Cathode
PublikacjaThe dynamic impedance analysis of direct methanolfuel cell (DMFC) cathode supplied with pure oxygen is pre-sented. Presented results were obtained during dynamic chang-es of the current density in working fuel cell. Investigation ofthe occurring processes at cathode was carried with dynamicelectrochemical impedance spectroscopy (DEIS). A discussionwas conducted based on the determined correlation parameterχ2. It was shown that...
-
Performance of the PEM fuel cell module. Part 2. Effect of excess ratio and stack temperature
PublikacjaThe paper describes a fuel cell based system performance under different thermal conditions. The system could be fed with bottled hydrogen or with very high purity hydrogen obtained from reforming of methanol. The system is based on two fuel cell units (1.2 kW each, produced by Ballard Power Systems Inc. and called Nexa), DC/DC converter, DC/AC inverter, microprocessor control unit, load unit, bottled hydrogen supply system and...
-
Effect of interconnect coating procedure on solid oxide fuel cell performance
PublikacjaChromium (Cr) species vaporizing from chromia-forming alloy interconnects is known as a source of degradation in solid oxide fuel cell (SOFC) stacks called “cathode poisoning”. (Mn,Co)3O4 spinel coatings offer good protection against Cr evaporation during operation. In this study, Crofer 22 APU steel interconnects were electrophoretically deposited in different mediums to obtain high packing of green coating layer. The optimized...
-
A Novel Cryptic Clostridial Peptide That Kills Bacteria by a Cell Membrane Permeabilization Mechanism
PublikacjaThis work reports detailed characteristics of the antimicrobial peptide Intestinalin (P30), which is derived from the LysC enzyme of Clostridium intestinale strain URNW. The peptide shows a broader antibacterial spectrum than the parental enzyme, showing potent antimicrobial activity against clinical strains of Gram-positive staphylococci and Gram-negative pathogens and causing between 3.04 ± 0.12 log kill for Pseudomonas aeruginosa...
-
Dynamic impedance measurements of the Direct Methanol Fuel Cell cathode at various operating temperatures
PublikacjaThis article discusses the application of impedance analysis for diagnosing the cathode of a direct methanol fuel cell at various operating temperatures. The Dynamic Electrochemical Impedance Spectroscopy technique coupled with a linear current scan was applied for this purpose. This technique allowed the observation of changes in the cathode's properties in the fuel cell operating under real working conditions. An equivalent model...
-
Investigation of functional layers of solid oxide fuel cell anodes for synthetic biogas reforming
PublikacjaSolid oxide fuel cells (SOFCs) are one of the most promising energy conversion devices due to their high efficiency, low pollution and fuel flexibility. Unfortunately, when hydrocarbons are used as a fuel, for example in the form of a biogas, solid carbon can deposit on the anode surface. This process leads to the degradation of the fuel cell performance. A possible solution to this problem is to apply an additional catalytic material,...
-
Stainless steel/yttria stabilized zirconia composite supported solid oxide fuel cell
PublikacjaW tym artykule opisano wytworzenie i przebadanie kompozytowych elementów nośnych tlenkowych ogniw paliwowych. Podłoża nośne zostały wytworzone ze stali nierdzewnej i tlenkiem itru stabilizowanego tlenku cyrkonu (YSZ), których proszki zmieszano w różnych proporcjach objętościowych. Zachowanie podłoży podczas spiekania (skurcz liniowy, porowatość) oraz wysokotemperaturowe właściwości (odporność na utlenianie, przewodność elektryczna)...
-
Sustainable energy system combined biogas-feedSolid Oxide Fuel Cell and Microalgae technology
PublikacjaIn the new frontier of energy and environmental safety, new efficient and clean safe energy conversion systems are required. In this sense, the present work is framed within the context of Circular Economy and proposes a multidisciplinary study for the development of more efficient, economically viable and non-polluting energy conversion systems, based on the synergetic combination of different technologies: fuel cells, biofuels,...
-
DESIGN ANALYSIS OF HYBRID GAS TURBINE - FUEL CELL POWER PLANT IN STATIONARY AND MARINE APPLICATIONS
PublikacjaThe paper concerns design analysis of a hybrid gas turbine power plant with a fuel cell (stack). The aim of this work was to find the most favorable variant of the medium capacity (approximately 50 MW) hybrid system. In the article, computational analysis of two variants of such a system was carried out. The analysis let to calculate capacity, efficiency of both variants and other parameters like flu gas temperature. The paper...
-
Fully enzymatic mediatorless fuel cell with efficient naphthylated carbon nanotube-laccase composite cathodes
PublikacjaAn efficient, mediator-free enzymatic glucose/O2 biofuel cell with an oxygen intensive anode based on glucose dehydrogenase is presented. In the device,the power of the biofuel cell and electrode potentials of each of the enzymatic electrodes were monitored in parallel under the biofuel cell working conditions. The carbon nanotube composite biocathode demonstrates an almost constant electrode potential vs. saturated calomel electrode...
-
Study of Direct Methanol Fuel Cell Process Dynamics Using Dynamic Electrochemical Impedance Spectroscopy
PublikacjaA new technique, which was developed to characterize the direct methanol fuel cell under work conditions, has been presented in this paper. The impedance measurements were made using dynamic electrochemical impedance spectroscopy research technique in the galvanostatic mode, using multiple sinusoidal excitation. Obtained results show, that together with an increase of the temperature and working load, the global impedance...
-
Application of wet powder spraying for anode supported solid oxide fuel cell with a perowskite SrTi0.98Nb0.02O3-d anode
PublikacjaAnode-supported solid oxide fuel cell with SrTi0.98Nb0.02O3–d anode, yttria-stabilized zirconia electrolyte and La(Ni0.6Fe0.4) O3d cathode has been successfully fabricated and evaluated. Process of anode support fabrication has been presented. Wet powder spraying and high temperature sintering method have been studied and applied to deposit the thin electrolyte layer.In order to improve catalytic properties of the anode, it has...
-
Impedance monitoring of fuel cell stacks
Publikacja -
Electrochemical performance of Co3O4/CeO2 electrodes in H2S/H2O atmospheres in a proton-conducting ceramic symmetrical cell with BaZr0.7Ce0.2Y0.1O3 solid electrolyte
PublikacjaThe electrochemical performance of Co3O4/CeO2 mixed oxide materials as electrodes, when exposed to H2S/H2O atmospheres, was examined employing a proton conducting symmetrical cell, with BaZr0.7Ce0.2Y0.1O3 (BZCY72) as the solid electrolyte. The impact of temperature (700–850 °C) and H2S concentration (0–1 v/v%) in steam-rich atmospheres (90 v/v% H2O) on the overall cell performance was thoroughly assessed by means of electrochemical...
-
Performance of the methanol PEM fuel cell module
PublikacjaPrzedstawiono charakterystyki układu zasilania składającego się z dwóch ogniw paliwowych o mocy 1.2 kW każde. Układ był zasilany metanolem, który podlegał procesowi reformowania w reformerze firmy Genesis Fueltech. Sprawność reformera wzrastała od 33% dla obciążenia minimalnego do 78% przy obciążeniu maksymalnym. Czystość uzyskiwanego wodoru była satysfakcjonująca w całym zakresie pracy reformera.
-
Cell Membrane Transport Mechanisms: Ion Channels and Electrical Properties of Cell Membranes
Publikacja -
Application analysis of a hybrid solid oxide fuel cell-gas turbine system for marine power plants
PublikacjaThe results of theoretical studies of the possibilities of using hybrid solid oxide fuel cell–gas turbine (SOFC-GT) systems for marine power plants are presented. A 500 kW auxiliary marine power plant scheme using stacks of SOFCs in combination with a regenerative gas turbine operating with over-expansion based on our recent patent application is proposed. The results of mathematical modelling showed the opportunity to obtain a...
-
A novel technology of solid oxide fuel cell fabrication
PublikacjaW pracy przedstawiono metodę wytwarzania wartstw i materiałów elektroceramicznych. Metoda jest kombinacją metod nanoszenia szkieletu z proszków ceramicznych i prekursorów polimerowych. Umożliwia ona otrzymanie zarówno gęstych jak i porowatych warstw i materiałów jednorodnych oraz kompozytowych. W pracy przedstawiono przykłady struktur dla tlenkowych ogniw paliwowych.
-
Advanced XAS analysis for investigating fuel cell electrocatalysts
PublikacjaW pracy została zaprezentowana analiza XAFS nanocząstek platyny używanych jako materiał katalityczny w niskotemperaturowych ogniwach paliwowych. Analiza danych EXAFS została przeprowadzona za pomocą zaawansowanej metody GNXAS, w której wzięto pod uwagę rozkład rozmiaru granul nano-platyny i niejednorodność warstwy katalitycznej elektrody, badane za pomocą SEM (skaningowy mikroskop elektronowy), TEM (transmisyjny mikroskop elektronowy)...
-
Influence of stack temperature on PEM fuel cell performance
PublikacjaW pracy przedstawiono wpływ temperatury stosu na wydajność ogniwa paliwowego typu PEM dla zadanego obciążenia. Badania ogniwa paliwowego przeprowadzono dla sześciu temperatur pracy stosu z zakresu od 30 oC do 65 oC. Dla najwyższej temperatury stosu, tj. 65 oC, wydajność pracy ogniwa paliwowego była najwyższa. Wraz ze wzrostem temperatury stosu zarejestrowano spadek mocy ogniwa paliwowego od 1015 W dla temperatury 30 oC do 1004...
-
On-line Impedance Monitoring of Direct Methanol Fuel Cell
PublikacjaW niniejszej pracy została przedstawiona technika badawcza Dynamiczna Elektrochemiczna Spektroskopia Impedancyjna w obszarze badań ogniw paliwowych. Obiektem badań było ogniwo paliwowe zasilane bezpośrednio metanolem. Badano on-line wpływ zmian warunków pracy na globalną impedancję ogniwa. Podczas pomiarów zmianie ulegała temperatura, natężenia przepływu utleniacza oraz obciążenie.
-
In situ study of a composition of outlet gases from biogas fuelled Solid Oxide Fuel Cell performed by the Fourier Transform Infrared Spectroscopy
PublikacjaThe purpose of this study was to develop a method and software based on the Fourier Transform Infrared Spectroscopy for the in-situ, quantitative analysis of the composition of outlet gases from Solid Oxide Fuel Cell (SOFC). The calibration procedure performed at the beginning of the experiment indicated a polynomial dependence between the concentration of a calibrating gas (CO, CO2, CH4) and the corresponding integrated absorbance in...
-
Low temperature processed MnCo2O4 and MnCo1.8Fe0.2O4 as effective protective coatings for solid oxide fuel cell interconnects at 750 °C
PublikacjaIn this study two materials, MnCo2O4 and MnCo1.8Fe0.2O4 are studied as potential protective coatings for Solid Oxide Fuel Cell interconnects working at 750 °C. First powder fabrication by a modified Pechini method is described followed by a description of the coating procedure. The protective action of the coating applied on Crofer 22 APU is evaluated by following the area specific resistance (ASR) of the scale/coating for 5500...
-
Fuel cell noise data
Dane BadawczeMeasurement data of Hydrogen PEM fuel cels. The voltage fluctuations were measured over single cels of stack of 10 cels.
-
Physical and sealing properties of BaO–Al2O3–SiO2–CaO–V2O5 glasses for solid oxide fuel cell applications
PublikacjaIn this study, the properties of BaO–Al2O3–SiO2 (SAB) glasses incorporated with CaO and V2O5 as the network modifier and additive, respectively, are evaluated. The electrical resistivities of the glasses decrease upon the addition of CaO but increase upon increasing their V2O5 content because the V5+ species lower the ionic mobility of the glasses. The addition of V2O5 improves the wettability of the glasses on the Crofer 22 APU...