Wyszukiwarka
Filtry
wszystkich: 58
Wyniki wyszukiwania dla: TRANSFER INTENSIFICATION
-
Heat transfer intensification by enlarged surface roughness in the plate heat exchanger
PublikacjaIn the paper an experimental analysis of passive heat transfer intensification technique employed in the case of the plate heat exchanger is presented. The passive intensification was obtained by a modification of the heat transfer surface. The roughness of surface was increased by a use of glass micro-beads. Single-phase convective heat transfer in the water-water system was studied. The experiment was accomplished in two stages....
-
Experimental study of heat transfer intensification in surface cooling using microjets
PublikacjaW pracy przedstawiono badania eksperymentalne intensyfikacji wymiany ciepła podczas chłodzenia powierzchni mikrostrugami. Wyniki badań porównano z własnym modelem teoretycznym zjawiska.
-
Heat transfer intensification by jet impingement – numerical analysis using RANS approach
PublikacjaJet impingement is a method of the heat transfer enhancement applied in the engineering systems. The idea is to generate fast-flow fluid jet which impinge on the heated (or cooled) surface, causing significantly higher heat transfer rate. Although some flat surface jet impingement cases are described in the literature, the validated data is still limited. The reason is coming from the fact, that these flows are hydrodynamically...
-
Intensyfikacja wymiany ciepła przy pomocy mikrostrug = Heat transfer intensification using microjets.
PublikacjaW pracy przedstawiono wyniki badań eksperymentalnych nad intensyfikacją strumienia ciepła przy pomocy pojedynczej mikrostrugi wody. W pracy przedstawiono wyniki badań dla dysz o średnicy 180 i 280 mikrometrów.
-
Recent advances of selected passive heat transfer intensification methods for phase change material-based latent heat energy storage units: A review
PublikacjaThe following article overviews recent studies regarding heat transfer enhancement methods, explicitly focusing on fins and coils utilization, in phase change material-based latent heat thermal energy storage systems. It discusses the influence of various geometrical and material parameters on the melting and solidification processes, as well as the orientation of the heat transfer surface within the storage tank. Additionally,...
-
Influence of nanoparticle concentration on convective heat transfer of water-Al2O3 nanofluids inside horizontal tubes
PublikacjaNanofluids came to be seen as a new generation of coolants, especially in single-phase systems. Conducted experiments indicate that the increase in thermal conductivity is not the only reason for the intensification of heat transfer when using nanofluids. Preliminary results of the experimental investigation of the forced convection heat transfer of water-Al2O3 nanofluids inside stainless steel tube with 8 mm internal diameter...
-
Heat transfer and pressure drop characteristics of the silicone-based plate heat exchanger
PublikacjaThe paper presents an experimental investigation of a silicone based heat exchanger, with passive heat transfer intensification by means of surface enhancement. The main objective of this paper was to experimentally investigate the performance of a heat exchanger module with the enhanced surface. Heat transfer in the test section has been examined and described with precise measurements of thermal and flow conditions. Reported...
-
Flow boiling intensification in minichannels by means of mechanical flow turbulising inserts
PublikacjaThe work presents the results of experimental investigation on heat transfer in minichannels. Refrigerant R123 was used as a test fluid. Single vertical silver tubes of 380 mm length and 2.3 mm diameter were examined with two variants of turbulising inserts. A wide range of parameters was considered, namely mass flux G=534-3011 kg/(m2s), heat flux qw=28.5-68.4 kW/m2, saturation temperature Tsat=23-86 stC and the full range of vapour...
-
Plate heat exchanger with porous structure for potential use in ORC system
PublikacjaThe experimental analysis of passive heat transfer intensification in the case of plate heat exchanger has been carried out. The passive intensification was obtained by a modification of the heat transfer surface, which was covered by a metallic porous microlayer. The experiment was accomplished in two stages. In the first stage the commercial stainless steel gasketed plate heat exchanger was investigated, while in the second one...
-
Plate heat exchanger with porous structure for potential use in ORC system
PublikacjaThe experimental analysis of passive heat transfer intensification in the case of plate heat exchanger has been carried out. The passive intensification was obtained by a modification of the heat transfer surface, which was covered by a metallic porous microlayer. The experiment was accomplished in two stages. In the first stage the commercial stainless steel gasketed plate heat exchanger was investigated, while in the second one...
-
Applicability of arrays of microjets heat transfer correlations to design compact heat exchangers
PublikacjaThe article presents experimental studies on a compact heat exchanger with heat transfer intensification by means of impinging microjets. The pursuit to provide high performance of heat exchangers is a response to the demand both in economics and in the universal tendency to miniaturization of industrial equipment. This paper presents the design and tests of a prototype, microjet heat exchanger. The modular design of the heat exchanger...
-
Influence of metallic porous microlayer on pressure drop and heat transfer of stainless steel plate heat exchanger
PublikacjaThe experimental analysis of passive heat transfer intensification in the case of plate heat exchanger has been carried out. On the heat transfer surface of heat exchanger the metallic porous layer was created. The experiment was accomplished in two stages. In the first stage the commercial stainless steel gasketed plate heat exchanger was investigated, while in the second one – the identical heat exchanger but with the modified...
-
Influence of metallic porous microlayer on pressure drop and heat transfer of stainless steel plate heat exchanger
PublikacjaThe experimental analysis of passive heat transfer intensification in the case of plate heat exchanger has been carried out. The metallic porous layer was created on the heat transfer surface of analyzed unit. The experiment was accomplished in two stages. In the first stage the commercial stainless steel gasketed plate heat exchanger was investigated, while in the second one – the identical heat exchanger but with the modified...
-
Bartosz Dawidowicz dr inż.
OsobyAbsolwent Wydziału Budowy Maszyn Politechniki Gdańskiej Mgr inż. - Wydział Budowy Maszyn Politechniki Gdańskiej: specjalizacja: Maszyny i Urządzenia Przemysłu Spożywczego (2000)Dr - Wydział Budowy Maszyn Politechniki Gdańskiej, dyscyplina: budowa i eksploatacja maszyn, specjalność: wymiana ciepła (2008) Zainteresowania naukowe dotyczą m.in. technik wodorowych – ogniwa paliwowe, wykorzystanie wodoru na cele energetyczne, odnawialnych...
-
Heat transfer characteristics of hybrid microjet – Microchannel cooling module
PublikacjaThe paper presents experimental investigation of heat transfer intensification in a microjet–microchannel cooling module. Applied technology takes benefits from two very attractive heat removal techniques. When jets are impinging on the surface, they have a very high kinetic energy at the stagnation point, also in microchannels boundary layer is very thin allowing to obtain very high heat fluxes. Main objective of this paper was...
-
Heat transfer characteristics of hybrid microjet -microchannel cooling module
PublikacjaThe paper presents the experimental investigation of heat transfer intensification in a microjet- microchannel cooling module. Applied technology takes benefits from two very attractive heat removal techniques. When jets are impinging on the surface, they have a very high kinetic energy at the stagnation point, also in microchannels boundary layer is very thin allowing to obtain very high heat fluxes. Main objective of this paper...
-
Effect of surface roughness on thermal-hydraulic characteristics of plate heat exchanger
PublikacjaIn the paper the experimental analysis of passive heat transfer intensification in the case of modeled plate heat exchanger is conducted. The plate heat exchanger is chosen for the analysis because this kind of heat exchangers could be prospectively applied in the ORC systems, however other areas or application are equally possible. The experimental setup was assembled at the Department of Energy and Industrial Apparatus of Gdansk...
-
Thermodynamic and geometrical characteristics of mixed convection heat transfer in the shell and coil tube heat exchanger with baffles
PublikacjaThe article presents passive heat transfer enhancement method in the form of baffles to increase the energy efficiency of the shell coil heat exchanger. Conducted literature review shows that, despite numer- ous studies, there is little work on the intensification of heat transfer at the shell side. Most of the work focuses on the impact of geometrical parameters of the coil itself. This article successfully proves that it is possible...
-
Thermal-Hydraulic Studies on the Shell-and-Tube Heat Exchanger with Minijets
PublikacjaIn this paper a patented design of a heat exchanger with minijets, with a cylindrical construction is presented. It is followed by the results of its systematic experimental investigations in the single-phase convection heat transfer mode. Based on these results, validation of selected correlations (coming from the literature) describing the Nusselt number was carried out. An assessment of the heat exchange intensification level...
-
Impact of Temperature and Nanoparticle Concentration on Turbulent Forced Convective Heat Transfer of Nanofluids
PublikacjaTheoretical analysis of the influence of nanoparticles and temperature on the average Nusselt (Nu) number and the average heat transfer coefficient (HTC) during the turbulent flow of nanofluid in a horizontal, round tube was carried out. The Nu number is a function of the Reynolds (Re) number and the Prandtl (Pr) number, which in turn are functions of the thermophysical properties of the liquid and the flow conditions. On the other...
-
Thermal Energy Storage with PCMs in Shell-and-Tube Units: A Review
PublikacjaThe paper presents a survey of the experimental and numerical studies of shell-and-tube systems in which phase change material (PCM) is used. Due to the multitude of design solutions for shell-and-tube systems, the emphasis is placed on double-tube (DT), triplex-tube (TT), and multitube (MT) units. Additionally, only single-pass systems are considered. Particular attention is paid to the method of heat transfer intensification....
-
Dariusz Mikielewicz prof. dr hab. inż.
OsobyDariusz Mikielewicz – urodził się 6 lutego 1967 roku w Gdańsku, w 1985r. zdał pomyślnie egzaminy wstępne na Wydział Budowy Maszyn Politechniki Gdańskiej, który ukończył z wynikiem bardzo dobrym w 1990 roku na specjalności Maszyny i Urządzenia Energetyczne. Zainteresowania pracą naukową skłoniły go do podjęcia badań na University of Manchester na wydziale mechanicznym i energetyki jądrowej (Mechanical and Nuclear Engineering Department)...
-
CHARAKTERYSTYKA WYMIANY CIEPŁA I OPORÓW PRZEPŁYWU OMYWANIA MIKROSTRUGAMI ROZWINIĘTEJ POWIERZCHNI
PublikacjaW artykule przedstawiono eksperymentalne badania kompaktowego wymiennika ciepła z intensyfikacją przejmowania ciepła przy użyciu mikrostrug. Niniejszy artykuł przedstawia projekt i testy prototypu, wymiennika ciepła typu mikrostrugowego. Modułowa konstrukcja wymiennika umożliwia zmianę wymiarów geometrycznych, a także zmianę materiału przegrody wymiennika ciepła. Metoda graficzna Wilsona została z zastosowana w celu określenia...
-
Experimental Investigations of Forced Convection of Nanofluids in Smooth, Horizontal, Round Tubes: A Review
PublikacjaA comprehensive review of published works dealing with experimental studies of forced convection heat transfer of nanofluids is presented. The survey is limited to straight, smooth, and round tubes. Moreover, only mono nanofluids exhibiting Newtonian behaviour are considered. Works on experimental research of forced convection in tubes are presented in a chronological order in the first part of the article. In this part, attention...
-
Flow distribution and heat transfer in minigap and minichannel heat exchangers during flow boiling
PublikacjaThe topic of boiling heat transfer in miniscale geometries has focused the ever increasing interest of researchers in recent years. However, most of the works are related to mini- and microchannels and much less to minigaps. Meanwhile, minigaps allow for more comprehensive experimental studies, i.e. flow visualisations due to the flat, two-dimensional configuration of the flow. The results of the experimental investigations of...
-
Experimental investigations on heat transfer enhancement in shell coil heat exchanger with VARIABLE Baffles GEOMETRY
PublikacjaThe paper presents the possibility of using passive intensification of heat transfer in the form of baffles to increase the energy efficiency of the shell and coil heat exchanger. The experiment was carried out by using a modular coil heat exchanger in the form of an electric heater. Water was used as a working fluid with constant thermal-flow parameters at the inlet of the module. It should be noted that experiments were made...
-
Performance analyses of helical coil heat exchangers. The effect of external coil surface modification on heat exchanger effectiveness
PublikacjaThe shell and coil heat exchangers are commonly used in heating, ventilation, nuclear industry, process plant, heat recovery and air conditioning systems. This type of recuperators benefits from simple construction, the low value of pressure drops and high heat transfer. In helical coil,centrifugal force is acting on the moving fluid due to the curvature of thetube results in the development. It has been long recognized that the...
-
Selected aspects of two-phase flow studies using different visualization techniques in minichannels
PublikacjaThe subject of the study is to present the possibility of the use of visualization techniques in the researches on two-phase flows, carried out by the authors for many years. These works included as follows: heat transfer during the flow boiling, boiling crises and condensation in flow. The issue of the heat transfer intensification during the flow boiling through the channels of small diameters was analyzed. All this work focused...
-
Janusz Cieśliński prof. dr hab. inż.
OsobyUrodził się 15 kwietnia 1954 r. w Słupsku. Jest absolwentem Wydziału Budowy Maszyn Politechniki Gdańskiej (1978), z którą związał całe swoje życie zawodowe. W 1986 r. obronił doktorat, w 1997 r. – habilitację, w 2006 r. – uzyskał tytuł profesora. Pełnił funkcje prodziekana ds. nauki Wydziału Mechanicznego przez dwie kadencje (2002–2008) oraz kierownika: Katedry Maszyn Przemysłu Spożywczego (2002–2006), Katedry Ekoinżynierii i...
-
A new construction of shell-and-tube heat exchanger with impinging jets and minichannels technologies for heat recovery from gases – experimental analysis
PublikacjaA dynamic development of technologies allowing waste heat utilization is observed in a correspondence with a pro-ecological approach of the zero waste idea. Such approach becomes the most demanding in the area of low-temperature was heat sources, especially gaseous media. Till now, they were usually not utilized due to unfavorable thermal conditions and high costs. Therefore, the zero waste approach directs research on techniques...
-
Curved Surface Minijet Impingement Phenomena Analysed with ζ-f Turbulence Model
PublikacjaThe jet impingement phenomenon plays an important role among the heat transfer intensification methods. Very often its application and analyses refer to simple flat surfaces, while there is a lack of information in the literature for cases addressing curved surfaces. In the present work, the single jet impingement on the non-flat (concave and convex) surface is studied for a wide range of geometries, which originate from the mini-jet...
-
Numerical analysis of high temperature minichannels heat exchanger performance
PublikacjaNowadays, the most difficult technological challenge in energy sector is connected with the gas micro-CHP units, dedicated to the distributed power generation. They are expected to be of high efficiency and at the same time of compact in size. Regarding the first reason, significant increase in microturbine efficiency can only be achieved by increase in the engine operating temperature. Therefore, one of the critical elements in...
-
Numeryczna analiza możliwości zwiększenia efektywności grzewczej pompy ciepła, poprzez modyfikację skraplacza
PublikacjaW niniejszej pracy określono charakterystykę prostego modelu wymiennika ciepła bazującego na skraplaczu powietrznej pompy ciepła. Jest to helikoidalny rekuperator typu rura w rurze. Zaproponowano i poddano analizie numerycznej dwie metody intensyfikacji wymiany ciepła i zestawiono wyniki z modelem porównawczym. Zastosowane rozwiązania zwiększające strumień wymienianego ciepła spowodowały wzrost odbieranego przez wodę strumienia...
-
Microjet technology as a perspective intensification method for high performance heat exchangers
PublikacjaIn the paper two oryginal designs of compact heat exchangers with intensification effect produced by microjets are presented. The technology of microjets manufacturing is an "inhouse" patented design. The idea of such heat exchanger is shown together with the flow and thermal characteristics of the prototypes. The results of performer measurements are satisfactory and encourage for further research of the original designs.
-
Possible directions for development of C-ITS services in cities on the example of the TRISTAR System
PublikacjaDuring the previous EU financial perspective (2007 - 2013), we observed an intensification of the evelopment of transport management systems using ITS services in Polish cities. One of the biggest territorially and functionally system is Tri-city TRISTAR system, the implementation of which was completed in 2015. The concept of the TRISTAR system and its architecture was developed in the years 2002-2007. Currently, we can observe...
-
Anthropopressure’s intensification with reference to Arctic ecosystems
PublikacjaThis paper concerns issue of long range atmospheric transport of pollutants to polar areas and intensification of their toxic effect on biota in the face of climate change. Arctic which was for years seen as a pristine and not affected by antropopressure region became a sink of xenobiotics. Atmospheric circulation facilitates transport of chemicals from Eurasia to Arctic. Influence of climate change on crucial balance of polar...
-
Intensification of thermal convection near electric devices using flat screens – computer modelling
PublikacjaIntensification of natural thermal convection near electric devices is possible by application of additional elements as screens creating convection canals close to the device. In the earlier authors paper the results of the analysis of thermal convection with the use of only one additional screen close to the electric device were presented. This paper presents computer modelling of thermal convection when two screens near the...
-
Numerical and experimental investigation of thermal convection near electric devices with vertical channels
PublikacjaThis paper presents the results of numerical and experimental investigation of thermal convection near heat emitting surfaces of an electric device. For the intensification of thermal convection, special vertical channels were formed near the heat emitting surfaces of the device. An experimental test has proved that there is an optimal length of the channels – thermal convection is the most intensive then. Air velocity vectors...
-
Electronic noses in classification and quality control of edible oils: A review
PublikacjaThe growing demand for wholesome and nutritious food leads to intensification of production, which in turn can have a detrimental effect on quality and well-being of consumers. For that reason, it is important to develop novel methods of food control which would be characterized by a short time of analysis, adequate sensitivity and relatively low cost. One such technique involves the use of multi-sensory devices called electronic...
-
Seashore sediment and water chemistry at the Admiralty Bay (King George Island, Maritime Antarctica) – geochemical analysis and correlations between the concentrations of chemical species
PublikacjaThis study covers water and sediment chemical characteristics by the western shore of Admiralty Bay (King George Island, Antarctica) in 2016. Chemical processes between sediment and water have been described based on the determination of ions, metals, non-metals, and TOC concentrations. Rock weathering is an important source of Fe, Ni, Co, Al in the seashore area. The PCA shows the impact of acidification in the release metals...
-
Structural Heterogeneity Between EU15 and 12 New EU Members – the Obstacle to Lisbon Strategy Implementation
PublikacjaThe aim of this article is to identify diversity between the EU-15 and the New Members in their implementation of the Lisbon Strategy in the period 2000-2010. By analyzing a set of structural indicators, we aim to fill a gap in the literature: a lack of publications providing complex evaluation of the implementation of the Lisbon Strategy using measurable indicators. Given their suitability for international comparisons, we use...
-
GVC involvement and the gender wage gap: Micro -evidence on European countries
PublikacjaWe examine linkages between involvement in global value chains (GVCs) and gender wage inequalities. We use merged data from Structure of Earnings Survey and the World Input Output Database covering 18 European countries. We employ information on employees’ personal and company characteristics and a sectoral involvement in GVCs. In general, the wages of workers from sectors more involved in GVCs are lower. However, the relationship...
-
Technology-Driven Internationalization: Central-Eastern European Perspective
PublikacjaSince the 1990s of the twentieth century onward, Central-Eastern European countries have been extensively involved in these two processes—regarding increasing share of ICT and high-tech exports in country’s total export value—and additionally, across these economies, changes in the level of access to and use of ICT have been observed. The main target of this research is to contribute to the present state of the art, by proving...
-
Solid phase microextraction: state of the art, opportunities and applications
PublikacjaSolid phase microextraction is one of the most popular green techniques used for sample preparations in analytical chemistry. It is a simple, rapid, sensitive, and solvent-free technique. Since SPME was first introduced in the early 1990s, there has been an intensification of research in order to elaborate new methodical solutions in many research facilities around the world, which could increase the use of this technique. More...
-
The Impact of Drying Conditions on the Surface Color Changes of Pine Wood
PublikacjaThe article presents the impact of drying process and selected parameters on the color changes on the surface of pine wood (Pinus sylvestris L.). Three predetermined process conditions (modes), mild, normal, and intensive, were investigated. The experiments were conducted using a semi-industrial scale dryer designed at the Gdańsk University of Technology with a loading capacity of 0.55 m3. The drying process was applied to pine...
-
Investigation of the Efficiency of a Dual-Fuel Gas Turbine Combustion Chamber with a Plasma‒Chemical Element
PublikacjaThe study is devoted to the possibility of increasing the efficiency of the working process in dual-fuel combustion chambers of gas turbine engines for FPSO vessels. For the first time, it is proposed to use the advantages of plasma‒chemical intensification of the combustion of hydrocarbon fuels in the dual-fuel combustion chambers, which can simultaneously operate on gaseous and liquid fuels. A design scheme of a combustion chamber...
-
Upward convergence patterns in chosen environmental-related SDGs
PublikacjaSustainable development is a challenge facing humanity. EU countries not only strive to reach their specific objectives, but they also work collaboratively towards shared goals. There is a need to balance synergies and compromises to address these objectives effectively. When discussing countries' development and people's well-being, one often focuses on socio-economic development. However, it is crucial not to overlook the environmental...
-
Intensification of catechin extraction from the bark of Syzygium cumini using ultrasonication: Optimization, characterization, degradation analysis and kinetic studies
PublikacjaCatechin is a prominent polyphenolic component that possesses various medicinal properties. Present work communicates the intensification and optimization of catechin extraction from the bark of Syzygium cumini tree using stirred reactor, soxhlet, ultrasonic bath, and ultrasonic horn technique. The optimization of several parameters such as type of solvent, solid to solvent ratio (1:100 w/v), speed of agitation (300 RPM), extraction...
-
The use of constructed wetlands for the treatment of industrial wastewater
PublikacjaConstructed wetlands are characterized by specific conditions enabling simultaneous various physical and biochemical processes. This is the result of specific environment for the growth of microorganisms and hydro-phytes (aquatic and semiaquatic plants) which are capable of living in aerobic, anaerobic and facultative anaerobic conditions. Their interaction contributes to the intensification of oxidation and reduction responsible...
-
Assessment of toxic and endocrine potential of substances migrating from selected toys and baby products
PublikacjaAnalysis of literature data shows that there is limited information about the harmful biological effects of mixture of compounds from the EDC group that are released from the surface of toys and objects intended for children and infants. One of the tools that can be used to obtain such information is appropriate bioanalytical tests. The aim of this research involved determining whether tests that use living organisms as an active...