Filtry
wszystkich: 236
Wyniki wyszukiwania dla: heat source
-
Management of low-temperature heat source by ORC aided by additional heat source
PublikacjaThe presented work is aimed at utilisation of waste heat in the manner to produce electricity in ORC installation. Therefore the precondition of the study was to use the waste heat available in the form of a stream of hot water at 90°C. Such low enthalpy heat source is rather insufficient to produce a good quality vapour to feed the ORC turbine. That was the incentive to search for the ways of increasing the temperature of the...
-
Management of low-temperature heat source by ORC aided by additional heat source
PublikacjaIn the paper presented is a concept to utilize waste heat from the power plant with the aid of the low-temperature ORC cycle. The ORC system is heated from two heat sources, the first one being the flow rate of waste heat obtained from the exhaust gases. Subsequently, the working fluid in the cycle is additionally heated by the condensing steam from the low pressure turbine extraction points increasing in such way the level of...
-
Distribution of heat generated by a local heat source
PublikacjaW pracy przedstawiono analizę rozpływu ciepła wygenerowanego przez lokalne źródło umieszczone w płycie, po której przepływa warstwa wody.
-
Gas boiler as a heat source for the domestic micro-CHP
PublikacjaThis analysis considers a commercially available domestic gas boiler as a heat source for a domestic organic Rankine cycle system. An experimental study was made into the applicability of the gas boiler (De Dietrich with thermal power 25 kW) coupled with the laboratory prototype micro ORC setup. The main aim of the study is to determine the working fluid temperature, attainable heat rates and effciencies of the whole system. Preliminary...
-
Gas boiler as a heat source for the domestic micro-CHP
PublikacjaIn the presented analysis a commercially available domestic gas boiler as a heat source for domestic ORC is considered. The applicability of the gas boiler (De Dietrich with thermal power 25 kW) coupled with the laboratory prototype micro ORC setup has experimentally studied. The main aim of the study is to determine the working fluid temperature, attainable heat rates and efficiencies of the whole system. Preliminary investigations...
-
Perfect thermal contact of hyperbolic conduction semispaces with an interfacial heat source
PublikacjaThe problem of thermal contact between two bodies with a heat source at their interface presents great scientific and practical interest. On the time scale of a nanosecond or shorter, heat propagation should be considered in the form of thermal waves of finite speeds. This study investigated the thermal behaviour of hyperbolic conduction semispaces in perfect thermal contact subjected to the action of an interfacial heat source....
-
Modeling of Heat Source Based on Parameters of Electron Beam Welding Process
Publikacja -
Utilisation of bleed steam heat to increase the upper heat source temperature in low-temperature ORC
PublikacjaW pracy przedstawiono możliwość dogrzewu obiegu ORC za pomocą pary upustowej.
-
Experimental investigations of commercial gas boiler as a heat source for the domestic micro-CHP
PublikacjaW pracy przedstawiono wyniki badań przeprowadzonych na prototypowym stanowisku mikrosiłowni domowej ORC z kotłem gazowym jako źródłem ciepła. Wykazano, iż jest możliwa adaptacja komercyjnego kotła gazowego dla potrzeb kogeneracji w skali mikro.
-
Analytical method for calculation of heat source temperature drop for the Organic Rankine Cycle application
PublikacjaIn the paper presented are considerations on the cooperation of the limited capacity heat source with the Organic Rankine Cycle unit. Usually the heat source providing thermal energy to the Organic Rankine Cycle (ORC) may have twofold characteristics. It can be in the form of a single phase fluid, i.e. as hot exhaust gas or hot liquid, or in some cases it may be available as a phase changing fluid, as for example, technological...
-
Particulate Matter Production of Small Heat Source Depending on the Bark Content in Wood Pellets
PublikacjaWood pellets as biofuel are more and more used in small heat sources in Europe. Standard wood pellets are produced from wood sawdust without bark. The paper deals about the impact of bark in wood pellets on their properties and combustion process. Special attention in this work is paid to production of particulate matter during combustion of wood pellets depending on bark content. There were experimentally produced spruce wood...
-
Thermal and solutal performance of Cu/CuO nanoparticles on a non-linear radially stretching surface with heat source/sink and varying chemical reaction effects
Publikacja -
Aiding (opponent) flow of hybrid copper–aluminum oxide nanofluid towards an exponentially extending (lessening) sheet with thermal radiation and heat source (sink) impact
Publikacja -
Nuclear power plant as a source of electrical energy and heat
PublikacjaIn this paper certain issues concerning usage of nuclear power plants as sources of not only electric power but also thermal energy will be discussed. For such a solution appeals most of all the need to limit harmful emissions of gases (including CO2) and ashes, which come from the process of burning fossil fuels, as well as the raising demand for network heat and chill. Additionally combined heat and power production brings measurable...
-
The Possibility to use a Nuclear Power Plant as a Source of Electrical Energy and Heat
PublikacjaIn this article issues concernig the possibility of nuclear power plant (NPP) operation also as a source of heat, which means combined heat and power production, have been described. CHP work is possible and profitable only in those areas where high thermal power demand occurs, which means near city agglomerations such as Warsaw or the Tri-City. Two levels of thermal power delivered to the heating system have been considered. Preliminary...
-
Utilisation of waste heat from the power plant by use of the ORC aided with bleed steam and extra source of heat
PublikacjaUtilization of waste heat recovered from the exhaust gases of the power generation unit by means of ORC (organic Rankine cycles) installation is considered. The waste heat is available in the form of a stream of hot water having temperature of 90 stC in the amount of 200 MWt. To increase evaporation temperaturę of ORC working fluid the heat of steam from the extraction points from the low-pressure part of steam turbine is used....
-
Operation of the 900 MW power plant with the ORC supplied from three heat sources
PublikacjaThe chapter is aimed at utilisation of waste heat in the reference supercritical power plant in the manner to produce electricity in ORC installation. The waste heat is available in the form of a stream of hot water at 90°C, recovered from the exhaust gases in the amount of 200MW. Such low enthalpy heat source is rather insufficient to produce a good quality vapour to feed the ORC turbine. Therefore an original approach to increase...
-
Galerkin finite element analysis of Darcy–Brinkman–Forchheimer natural convective flow in conical annular enclosure with discrete heat sources
Publikacja -
Modelling of the Heat Flux Density Distribution for Laser Beam Welding
PublikacjaGreat interest of the laser beam welding in industry is a new theoretical task, making planning the welding procedure specification and the quality control of welded joints easier. Estimating and calculating the dimensions of a weld pool and temperature distribution near weld mainly concern heat source modelling. In the presented work calculations of welding pool shape and thermal field for cylindrical-powered-normally model of...
-
High-temperature heat pumps – potential technology for heat recovery and production of process heat
PublikacjaIn the paper, the high temperature vapour compressor based heat pump with a selection of working fluids, both perspective and ecological ones, is considered. Such system is not yet commercially available on the market and in author’s opinion it has significant potential for various applications. In the presented analysis it was assumed that the heat source has a temperature of 50oC and the temperature lift is 60, 80 and 100K respectively....
-
Jeffreys heat conduction in coupled semispaces subjected to interfacial heating
PublikacjaA Jeffreys heat conduction problem for coupled semispaces subjected to the action of an interfacial heat source was defined. An analytical solution of the problem was derived for a polynomial specific power of the heat source using the Laplace transform approach. The asymptotic and parametric analysis was performed for different ratios of thermal conductivities , thermal diffusivities , thermal relaxation times and coefficients...
-
Analysis of Organic Rankine Cycle efficiency and vapor generator heat transfer surface in function of the reduced pressure
PublikacjaIn the paper presented is analysis of the influence of reduced pressure on efficiency and heat transfer area of vapor generator of Organic Rankine Cycle (ORC) in case of subcritical and supercritical parameters of operation. Compared are two cases of subcritical and supercritical ORC featuring a similar arrangement of heat source supply and heat removal, that is featuring the same temperatures of working fluid before the turbine,...
-
Parametric study of fluid flow and heat transfer over louvered fins of air heat pump evaporator
PublikacjaTwo-dimensional numerical investigations of the fluid flow and heat transfer have been carried out for the laminar flow of the louvered fin-plate heat exchanger, designed to work as an air-source heat pump evap- orator. The transferred heat and the pressure drop predicted by simulation have been compared with the corresponding experimental data taken from the literature. Two dimensional analyses of the louvered fins with varying...
-
Performance of the very high-temperature heat pump with low GWP working fluids
PublikacjaTraditional heat pumps are a very attractive pro-ecological solutions for a number of applications, including providing of heating or heat recovery from industrial processes. The application range of heat pumps could be greatly enlarged when the operating temperature would be increased to 130-150°C and/or the temperature lift can be increased to 50-100 K. In the paper, the very high temperature vapour-compressor based single stage...
-
HIGH TEMPERATURE HEAT PUMPS – PERSPECTIVE HEATING SYSTEMS?
PublikacjaIn the paper presented are authors own concepts of high temperature compressor heat pumps for the utilisation of medium and low temperature sources of heat. Working fluids for use in high temperature heat pumps are discussed, as well as the criteria for their selection. Analyses are presented for the production of in the upper steam source at 130 °C. One-stage systems and cascade systems were analyzed. An analysis of the coefficient...
-
Experimental and numerical analysis of the pyrolysis dynamics of a single wood particle: presentation of the radiographic technique
PublikacjaPyrolysis is an oxygen-free process for the thermal decomposition of raw materials. The heat conduction and flow of pyrolysis products (i.e., the gas fraction and liquid vapour generated during pyrolysis) influence the process and products. In this work, the influence of the orientation of wooden particle fibres with respect to the direction of the heat source on the dynamics of the process was investigated, where there were two...
-
Free Convection Heat Transfer from Horizontal Cylinders
PublikacjaThe results of experimental investigation of free convection heat transfer in a rectangular container are presented. The ability of the commonly accepted correlation equations to reproduce present experimental data was tested as well. It was assumed that the examined geometry fulfils the requirement of no-interaction between heated cylinder and bounded surfaces. In order to check this assumption recently published correlation equations...
-
Numerical analysis of high temperature minichannels heat exchanger performance
PublikacjaNowadays, the most difficult technological challenge in energy sector is connected with the gas micro-CHP units, dedicated to the distributed power generation. They are expected to be of high efficiency and at the same time of compact in size. Regarding the first reason, significant increase in microturbine efficiency can only be achieved by increase in the engine operating temperature. Therefore, one of the critical elements in...
-
Heat Transfer of the Multicolor-Laser-Sources-Irradiated Nanoparticles in Reference to Thermal Processes
PublikacjaUnlike the standard materials, metallic nanoparticles offer enhancing the heat convertion rate which implies the maximum and average temperature boost significantly in the considered system. The work’s purpose is to examine heat transfer in the metallic nanoparticles which have been deposited on a glassy substrate, enabling the nanostructures thermoablation. Furthermore, the functionalized substrate is irradiated with multicolor-laser-sources,...
-
Comparison of traditional district heating with low temperature district heating systems featuring organic Rankine cycle and heat pump
PublikacjaPaper presents a comparison between a traditional district heating system with conventional boilers as a source of heat and electricity purchases from power utilities and a low temperature DH system incorporating the CHP with organic Rankine Cycle providing electricity and local heat pump raising the temperature of the DH fluid to the required temperature in the dwelling, meaning that both heat and electricity are produced within...
-
Wpływ właściwości czynników chłodniczych na straty egzergii w pompie ciepła (Influence of Refrigerants Properties for Exergy Losses in Heat Pump)
PublikacjaArtykuł poświęcony jest wpływowi występujących w pompie ciepła strat egzergii na jej efektywność energetyczną, a co za tym idzie koszty funkcjonowania instalacji. Autorzy prezentują tu metodologię obliczeniową, która może być zastosowana w procesach projektowania układów cieplno-przepływowych. Obliczenia zostały wykonane na podstawie typowego układu powietrznej pompy ciepła pracującej w klimacie środkowo-europejskim. Ponadto w...
-
Two-phase optimizing approach to design assessments of long distance heat transportation for CHP systems
PublikacjaCogeneration or Combined Heat and Power (CHP) for power plants is a method of putting to use waste heat which would be otherwise released to the environment. This allows the increase in thermodynamic efficiency of the plant and can be a source of environmental friendly heat for District Heating (DH). In the paper CHP for Nuclear Power Plant (NPP) is analyzed with the focus on heat transportation. A method for effectivity and feasibility...
-
Adapting the pinch point analysis to improve the ORC design process
PublikacjaPinch point analysis can be adapted so as to assist in the early stages of designing the ORC systems. Typically used in determining the working parameters of heat exchangers, it can be employed to improve the heat fitting between the source of heat and the working fluids of the ORC system. To attain the parametric match, an algorithm was built enabling quick estimation of the possible heat reception by the specific working fluid....
-
Thermal cooling process by nanofluid flowing near stagnating point of expanding surface under induced magnetism force: A computational case study
PublikacjaThis paper is dedicated to the exam of entropy age and research of the effect of mixing nanosolid additives over an extending sheet. In this review, Newtonian nanofluid version turned into researched at the actuated appealing field, heat radiation and variable heat conductivity results. With becoming modifications, the proven PDEs are moved into popular differential situations and paintings mathematically making use of a specific...
-
Improved finite element method for flow, heat and solute transport of Prandtl liquid via heated plate
PublikacjaIn the current study, a vertical, 3D-heated plate is used to replicate the generation of heat energy and concentration into Prandtl liquid. We discuss how Dufour and Soret theories relate to the equations for concentration and energy. In order to see how efectively particles, interact with heat and a solvent, hybrid nanoparticles are used. It does away with the phenomena of viscous dissipation and changing magnetic felds. The motivation...
-
MOŻLIWOŚĆ WYKORZYSTANIA ELEKTROWNI JĄDROWEJ JAKO ŹRÓDŁA ENERGII ELEKTRYCZNEJ I CIEPLNEJ
PublikacjaW niniejszym artykule przedstawiono zagadnienia związane z możliwością pracy elektrowni jądrowej (EJ) również w charakterze źródła ciepła, a więc w warunkach skojarzonego wytwarzania energii elektrycznej oraz ciepła. Rozpatrzono dwa poziomy mocy cieplnych oddawanych do systemów ciepłowniczych. Przeprowadzone wstępnie badania techniczne i ekonomiczne dla lokalizacji elektrowni jądrowej nad Jeziorem Żarnowieckim potwierdziły potencjalną...
-
Increase of power and efficiency of the 900 MW supercritical power plant through incorporation of the ORC
PublikacjaThe objective of the paper is to analyse thermodynamical and operational parameters of the supercritical power plant with reference conditions as well as following the introduction of the hybrid system incorporating ORC. In ORC the upper heat source is a stream of hot water from the system of heat recovery having temperature of 90 °C, which is additionally aided by heat from the bleeds of the steam turbine. Thermodynamical analysis...
-
Quantitative study of free convective heat losses from thermodynamic partitions using Thermal Imaging
PublikacjaThe following paper presents a simple method of determining the presence, distribution and values of heat losses from external building walls as thermodynamic partitions using a Thermal Imaging Camera (TIC). According to Fourier's equation, the value of heat loss is proportional to the temperature gradient ∂t/∂y|y=0 in air in the y direction perpendicular to the heated surface. Unfortunately, air temperature cannot be measured...
-
Combined operation of 900MW power plant with the ORC through the bleed steam extraction point and CO2 recovery system
PublikacjaThe work presented here is aimed at utylisation of waste heat in the reference supercritical power plant in the manner to produce electricity in ORC installation. The waste heat is available in the form of a stream of hot water at 90 C, recovered from the exhaust gases in the amount of 200MW. Such low enthalpy heat source is rather insufficient to produce a good quality vapour to feed the ORC turbine. Therefore an original approach...
-
Microwave radiation in the synthesis of urethane prepolymers
PublikacjaThis paper describes the use of microwave radiation in the synthesis of urethane prepolymers in bulk (without solvent). The prepolymers were synthesized using 1,6-hexamethylene diisocyanate (HDI) and poly (ε-caprolactone) diol (PCL) at a molar ratio of 4:1. The reaction was carried out without a catalyst in the reactor with a conventional heating system (oil bath) or in the microwave reactor (MW Reactor NOVA 09) at temperatures...
-
Cooperation of ORC installation with a gas boiler as a perspective co-generation system for households
PublikacjaThis paper reports tests of an innovative micro-CHP unit prototype, consisting of a traditional gas boiler and organic Rankine cycle (ORC), which incorporates original system components such as an axial vapour microturbine, evaporator and condenser. The system co-generates heat and electricity for a single household or a group of households. Electricity is only a by-product during production of heat. While testing the prototype,...
-
Alternative cogeneration thermodynamic cycles for domestic ORC
PublikacjaThe Organic Flash Cycle (OFC) is suggested as a vapor power cycle that could potentially improve the efficiency of utilization of the heat source. Low and medium temperature finite thermal sources are considered in the cycle. Additionally the OFC’s aim is to reduce temperature difference during heat addition. The study examines 2 different fluids. Comparisons are drawn between the OFC and an optimized basic Organic Rankine Cycle...
-
Domestic ORC micro-CHP combined with a commercial gas boiler
PublikacjaThe chapter presents the results of experimental studies conducted during the launch of the first in Poland demonstration prototype of the micro ORC coupled to a domestic gas boiler. The accomplished studies indicated the possibility for the ORC module to work with such boiler (autonomous source of heat) with a prototype single-stage axial micro turbine as the expansion machine. Confirmation of that fact has been delineated in...
-
Galerkin Finite Element Process for Entropy Production and Thermal Evaluation of Third-Grade Fluid Flow: A Thermal Case Study
Publikacja: A fluid’s moving class improves its heat transmission capability, as well as its rigidity, owing to multivariate molecule suspension. In this way, nanofluids are superior to common fluids. In this study, we evaluated the features of ease and heat transfer. Furthermore, we investigated permeable media, heat source, variable heat conductivity, and warm irradiation results. A mathematical technique known as the Galerkin finite element...
-
Application of Stirling Engine Type Alpha Powered by the Recovery Energy on Vessels
PublikacjaThe Stirling engine is a device, in which thermal energy is transformed into mechanical without a contact between the heat carrier, and the working gas closed in the engine. Mentioned feature makes this type of engine very attractive for the use of the recovery energy, taken from other heat devices. One of the potential applications of Stirling engines is the use of thermal energy generated in the ship's engine room for producing...
-
Charakterystyka eksploatacyjna pomp ciepła zainstalowanych w oczyszczalni ścieków
PublikacjaW artykule przedstawiono charakterystykę eksploatacyjną sprężarkowych pomp ciepła zainstalowanych w oczyszczalni komunalnej i wykorzystujących ścieki oczyszczone jako dolne źródło ciepła. Zastosowanie ścieków oczyszczonych jest uzasadnione ich dostępnością oraz stosunkowo wysoką temperaturą (10-25°C). Prawidłowa eksploatacja układu wymaga zastosowania pośredniego obiegu parowacza oraz regularnych zabiegów czyszczenia wymiennika...
-
Static Model of Steam/Water Cycle for Thermal and Economic Analysis
PublikacjaThe thermodynamic efficiency of typical conventional and nuclear power plants is insufficient. A large amount of the generated heat is removed to the environment and regarded as a waste. A solution which is commonly used to increase the efficiency and profitability of the existing and planned power plants refers to cogeneration of heat and power. To prepare sophisticated thermodynamic and economic analyses, a precise static model...
-
A Theoretical and Experimental Study of Moderate Temperature Alfa Type Stirling Engines
PublikacjaThe Stirling engine is a device that allows conversion of thermal energy into mechanical energy with relatively high efficiency. Existing commercial designs are mainly based on the usage of high temperature heat sources, whose availability from renewable or waste heat sources is significantly lower than that of moderate temperature sources. The paper presents the results of experimental research on a prototype alpha type Stirling...
-
A commercial gas boiler fitted with the ORC module as perspective solution for households
PublikacjaIn this paper the applicability of the commercial gas boiler (De Dietrich DTG X23N) coupled with the laboratory prototype micro ORC setup was experimentally studied. The main objective was to determine the working fluid capability to obtain required temperatures of vapour prior to the turbine, attainable heat rates and efficiencies of the whole system. The boiler thermal power was 25 kW. Tests were carried out with a single stage...
-
Stirling engines - the state of technology development and computational models
PublikacjaStirling engines represent a technologically important solution in combined heat and power systems. Their use enables the achievement of over 90 percent efficiency in the management of the primary energy source with a very high durability of the device, mainly due to the lack of contact of the working gas with external factors and a very small number of mechanical components. The use of a Stirling engine may be equally important...
-
Market Price Prediction of Property Rights from Gas Fired Plants or Plants with Total Installed CHP Source Capacity Below 1 MW until 2025
PublikacjaThe resolution on the Polish Energy Policy until 2030 (PEP-30) was adopted by the Council of Ministers on 10 November 2009. The document specifies the combined electricity and heat generation as a direction of pursuing the goals of energy efficiency, fuel and energy supply security, competitive fuel and energy markets development, and reduction of the energy sector’s environmental impact. PEP-30 assumes that electricity generation...
-
Curved Surface Minijet Impingement Phenomena Analysed with ζ-f Turbulence Model
PublikacjaThe jet impingement phenomenon plays an important role among the heat transfer intensification methods. Very often its application and analyses refer to simple flat surfaces, while there is a lack of information in the literature for cases addressing curved surfaces. In the present work, the single jet impingement on the non-flat (concave and convex) surface is studied for a wide range of geometries, which originate from the mini-jet...
-
Numeryczna analiza możliwości zwiększenia efektywności grzewczej pompy ciepła, poprzez modyfikację skraplacza
PublikacjaW niniejszej pracy określono charakterystykę prostego modelu wymiennika ciepła bazującego na skraplaczu powietrznej pompy ciepła. Jest to helikoidalny rekuperator typu rura w rurze. Zaproponowano i poddano analizie numerycznej dwie metody intensyfikacji wymiany ciepła i zestawiono wyniki z modelem porównawczym. Zastosowane rozwiązania zwiększające strumień wymienianego ciepła spowodowały wzrost odbieranego przez wodę strumienia...
-
On dynamic modeling of piezomagnetic/flexomagnetic microstructures based on Lord–Shulman thermoelastic model
PublikacjaWe study a time-dependent thermoelastic coupling within free vibrations of piezomagnetic (PM) microbeams considering the flexomagnetic (FM) phenomenon. The flexomagneticity relates to a magnetic field with a gradient of strains. Here, we use the generalized thermoelasticity theory of Lord–Shulman to analyze the interaction between elastic deformation and thermal conductivity. The uniform magnetic field is permeated in line with...
-
Modular Approach for Modelling Warming Up Process in Water Installations with Flow-Regulating Elements
PublikacjaThe paper presents a new method for modelling the warming up process of a water system with elements regulating the flow in a stochastic manner. The paper presents the basic equations describing the work of typical elements which the water installation is composed of. In the proposed method, a new computational algorithm was used in the form of an iterative procedure enabling the use of boundary conditions that can be stochastically...
-
Verification of the method of reconstructing convective velocity fields on the basis of temperature fields in vertical, differential and equally heated, open and closed channels
PublikacjaThis paper describes a method of reconstructing velocity fields, i.e. a numerical reconstruction procedure (NRP) that involves the numerical processing of experimentally measured temperature distributions in free convection heat transfer. The NRP consists in solving only the continuity and Navier–Stokes equations with an additional source term. This term is proportional to a known temperature (e.g. from a thermal imaging camera)...
-
Experimental and theoretical study of a vertical tube in shell storage unit with biodegradable PCM for low temperature thermal energy storage applications
PublikacjaThis article presents the experimental investigations of the coconut oil-based TES module for HVAC applications in the ambient and-sub ambient temperature range. To properly study this problem modular experimental module and test loop were developed. Special attention has been paid to study the physical mechanism of the melting/solidification process for natural substance (coconut oil) which has perspectives to be used in thermal...
-
Different design aspects of an Organic Rankine Cycle turbine for electricity production using a geothermal binary power plant
PublikacjaIn recent years, pressure has been growing to increase the share of renewable energy sources in electricity generation, which may offer opportunities for the development of geothermal energy in regions that have been so far considered unprofitable in this respect. One such country currently undergoing an energy transition is Poland in which low-temperature geothermal resources are currently used for district heating and recreation...
-
Selected design and construction aspects of supercritical steam generators for high temperature reactors = Wybrane aspekty konstrukcyjne i projektowe generatorów pary nadkrytycznej ogrzewanych z reaktorów wysokotemperaturowych
PublikacjaW artykule zaprezentowano uwarunkowania projektowe i konstrukcyjne nadkrytycznego generatora pary (jednoprzepływowego) wykorzystującego do ogrzewania hel z reaktorów HTR i VHTR. Wymiennik helikoidalny jest preferowany dla zwiększenia wymiany ciepła i zwartości. Badano własności czynników wymieniających ciepło z parą w obszarach przy- i nadkrytycznych. Analizowano korelacje, aby wybrać najbardziej wiarygodne. Przedyskutowano najbardziej...
-
Prediction of metal deformation due to line heating; an alternative method of mechanical bending, based on artificial neural network approach
PublikacjaLine heating is one of the alternative methods of forming metals and this kind of forming uses the heating torch as a source of heat input. During the process, many parameters are considered like the size of the substrate, thickness, cooling method, source power intensity, the travel speed of the power source, the sequence of heating, and so on. It is important to analyze the factors affecting the...
-
Interaction of Acoustic and Thermal Modes in the Gas with Nonequilibrium Chemical Reactions: Possibilities of Acoustic Cooling
PublikacjaNonlinear generation of thermal mode during propagation of dominative sound in a chemically reacting gas is considered. The dynamic equation of excess temperature associated with the thermal mode is derived. It is instantaneous and includes quadratic nonlinear acoustic source reflecting the nonlinear character of interaction between acoustic and non-acoustic types of gas motion. Both periodic and aperiodic sound may be considered...
-
Interaction of Acoustic and Thermal Modes in the Vibrationally Relaxing Gases. Acoustic Cooling
PublikacjaThe dynamic equation which governs an excess temperature associated with the thermal mode in vibrationally relaxing gas is derived. The nonlinear transfer of acoustic energy to the energy of the thermal mode in a relaxing gas causes slow variation of temperature with time. The nal dynamic equation is instantaneous. All types of sound, including aperiodic, may be considered as an acoustic source of corresponding heating or cooling....
-
Photovoltaic module temperature stabilization with the use of phase change materials
PublikacjaThe worldwide growth of photovoltaics (PVs) has formed an exponential curve for more than four decades. During this period of time, PVs have evolved from a pure niche market of small-scale applications towards becoming a mainstream electricity source. The influence of temperature on the electrical parameters of crystalline silicon solar cells and solar modules is well described in the literature. In order to diminish these effects,...
-
The Course and the Effects of Agricultural Biomass Pyrolysis in the Production of High-Calorific Biochar
PublikacjaThe thermal pyrolysis of agriculture biomass has been studied in a fixed-bed reactor, wherethe pyrolysis was conducted at a steady temperature of 800◦C. This work analyses the pyrolysisproducts of six agricultural wastes: pistachio husks, walnut husks, sunflower hulls, buckwheat husks,corncobs and coconut shells. The conducted research compared examples of large waste biomassstreams from different parts of the world as a potential...
-
Prowadzenie ruchu małego źródła kogeneracji gazowej według kryterium efektu ekonomicznego
PublikacjaCechą charakterystyczną źródeł gazowych jest ich duża elastyczność ruchowa, w porównaniu do większości źródeł konwencjonalnych i odnawialnych. Cecha ta może i powinna być wykorzystywana do poprawy wskaźników ekonomicznych obiektu. W tym celu należy przeanalizować możliwości jakie daje prowadzenie ruchu źródeł nie w standardzie pracy z wymuszeniem zapotrzebowania na ciepło, ale właśnie maksymalnie wykorzystując elastyczność ruchową...
-
Prowadzenie ruchu małej elektrociepłowni gazowej według kryterium efektu ekonomicznego
PublikacjaCechą charakterystyczną źródeł gazowych jest ich duża elastyczność ruchowa, w porównaniu do większości źródeł konwencjonalnych i odnawialnych. Cecha ta może i powinna być wykorzystywana do poprawy wskaźników ekonomicznych obiektu. W tym celu należy przeanalizować możliwości jakie daje prowadzenie ruchu źródeł nie w standardzie pracy z wymuszeniem zapotrzebowania na ciepło, ale właśnie maksymalnie wykorzystując elastyczność ruchową...
-
Stirling engines powered by renewable energy sources
PublikacjaStirling engine is a device that produces mechanical energy using heat from any source of energy, without the need of combustion of any fuel inside the device. Renewable energy sources, which are mostly low-temperature energy sources, can be used to produce mechanical and electrical energy in Stirling engines. The paper presents an overview of the existing prototype Stirling engines designed for using of low-temperature energy...
-
Technical and economic analysis of energy storage in the compressed air technology with low capacity for the production plant
PublikacjaCompressed air energy storage (CAES) system is a promising technology due to its numerous advantages, including relatively low maintenance cost, a long lifespan and high operational flexibility. This article explores the possibility of designing a CAES power plant as a source of electricity and heat for an existing industrial plant. The study involves the technical analysis of the power plant parameters and the economic analysis...
-
Organic Rankine as bottoming cycle to a combined Brayton and Clausius-Rankine cycle
PublikacjaThis paper presents an enhanced approach, as it will be considered here that the ORC installation could be extra-heated with the bleed steam, a concept presented by the authors. In such way the efficiency of the bottoming cycle can be increased and an amount of electricity generated increases. A thermodynamic analysis and a comparative study of the cycle efficiency for a simplified steam cycle cooperating with ORC cycle will be...
-
Influence of Laser Modification on the Surface Character of Biomaterials: Titanium and Its Alloys—A Review
PublikacjaLaser surface modification is a widely available and simple technique that can be applied to different types of materials. It has been shown that by using a laser heat source, reproducible surfaces can be obtained, which is particularly important when developing materials for medical applications. The laser modification of titanium and its alloys is advantageous due to the possibility of controlling selected parameters and properties...
-
Influence of Laser Modification on the Surface Character of Biomaterials: Titanium and Its Alloys—A Review
PublikacjaLaser surface modification is a widely available and simple technique that can be applied to different types of materials. It has been shown that by using a laser heat source, reproducible surfaces can be obtained, which is particularly important when developing materials for medical applications. The laser modification of titanium and its alloys is advantageous due to the possibility of controlling selected parameters and properties...
-
Efficiency and proportions of waste tyre pyrolysis products depending on the reactor type—A review
PublikacjaThis article discusses the current use of different pyrolytic reactors, their constructions and operating principles regarding the yields of main products of waste tyre pyrolytic recycling. Whether one makes a larger or smaller profit, or even a loss due to a surcharge being levied on waste tyre recycling, depends on the sale of the pyrolysis products (gas, char, oil), the proportions and market prices of which differ. The cheapest...
-
Green energy extraction for sustainable development: A novel MPPT technique for hybrid PV-TEG system
PublikacjaThe Photovoltaic (PV) module converts only a small portion of irradiance into electrical energy. Most of the solar energy is wasted as heat, resulting in a rise in PV cell temperature and a decrease in solar cell efficiency. One way to harvest this freely available solar thermal energy and improve PV cell efficiency is by integrating PV systems with thermoelectric generators (TEG). This cogeneration approach of the hybrid PV-TEG...
-
The Possibility of Phase Change Materials (PCM) Usage to Increase Efficiency of the Photovoltaic Modules
PublikacjaSolar energy is widely available, free and inexhaustible. Furthermore this source of energy is the most friendly to the environment. For direct conversion of solar energy into useful forms like of electricity and thermal energy, respectively photovoltaic cells and solar collectors are being used. Forecast indicate that the first one solution will soon have a significant part in meeting the global energy demand. Therefore it is...
-
Acoustic heating produced in resonators filled by a newtonian fluid
PublikacjaAcoustic heating in resonators is studied. The governing equation of acoustic heating is derived by means of the special linear combination of conservation equations in differential form, allowing the reduction of all acoustic terms in the linear part of the final equation, but preserving terms belonging to the thermal mode responsible for heating. This equation is instantaneous and includes nonlinear acoustic terms that form a...
-
MORPHOLOGY OF BUILDING DEVELOPMENT AS AN ELEMENT OF URBAN VENTIALTION SYSTEM
PublikacjaProblems related to air quality in large urban agglomerations (e.g., high concentration of pollutants, the urban heat island phenomenon) make it necessary to take comprehensive measures to improve air exchange in urban areas.The article concerns the relationship between wind phenomena observable in cities and the geometrical features of building development. The knowledge on the subject is already well-founded and has been intensively...
-
Failure analysis of a high-speed induction machine driven by a SiC-inverter and operating on a common shaft with a high-speed generator
PublikacjaDue to ongoing research work, a prototype test rig for testing high-speed motors/generators has been developed. Its design is quite unique as the two high- speed machines share a single shaft with no support bearings between them. A very high maximum operating speed, up to 80,000 rpm, was required. Because of the need to minimise vibration during operation at very high rotational speeds, rolling bearings were used. To eliminate...
-
Ocean mixed layer dynamics: high-resolution simulations of wind, wave and convective effects
Dane BadawczeThis dataset contains results of high-resolution numerical simulations of the ocean mixed layer (OML) forced by wind, waves and cooling from the atmosphere, i.e., under strongly turbulent, convective conditions. The goal is to provide detailed, three-dimensional information about OML circulation, turbulent kinetic energy, and temperature and salinity...
-
Organic Rankine cycle as bottoming cycle to a combined Brayton and Clausius - Rankine cycle
PublikacjaA preliminary evaluation has been made of a possibility of bottoming of a conventional Brayton cycle cooperating with the CHP power plant with the organic Rankine cycle installation. Such solution contributes to the possibility of annual operation of that power plant, except of operation only in periods when there is a demand for the heat. Additional benefit would be the fact that an optimized backpressure steam cycle has the advantage...
-
Process Control of Biogas Purification Using Electronic Nose
PublikacjaNowadays, biogas produced from landfills and wastewater treatment plants or lignocellulosic biomass is important sustainable and affordable source of energy. Impurities from biogas stream can cause a serious odor problem, especially for residents of areas immediately adjacent to production plants. Therefore, biogas pre-treatment is necessary to protect engines that convert biogas into energy and in order to increase the specific...
-
Influence of the notch rounding radius on estimating the elastic notch stress concentration factor in a laser welded tee joint
PublikacjaIn recent years an increased interest of industry in sandwich-type metal structures can be observed. These structures consist of thin plates of 2.5 mm in thickness separated by stiffeners of different shapes and forms. Welds joining the plates and stiffeners are made on the outer side of the plates using laser welding technique. A locally focused source of heat causes the plate to melt creating a very narrow and elongated joint....
-
Method of reconstructing two-dimensional velocity fields on the basis of temperature field values measured with a thermal imaging camera
PublikacjaThis paper describes a novel numerical reconstruction procedure (NRP) of the velocity field during natural convective heat transfer from a two-sided, isothermal, heated vertical plate based only on the known temperature field obtained, e.g. with a thermal imaging camera. It has been demonstrated that with a knowledge of temperature distributions, the NRP enables the reconstruction of velocity fields by solving the Navier-Stokes...
-
Cleaner energy for sustainable future using hybrid photovoltaics-thermoelectric generators system under non-static conditions using machine learning based control technique
PublikacjaIn addition to the load demand, the temperature difference between the hot and cold sides of the thermoelectric generator (TEG) module determines the output power for thermoelectric generator systems. Maximum power point tracking (MPPT) control is needed to track the optimal global power point as operating conditions change. The growing use of electricity and the decline in the use of fossil fuels have sparked interest in photovoltaic-TEG...
-
Mechanical Properties, Microstructure and Surface Quality of Polypropylene Green Composites as a Function of Sunflower Husk Waste Filler Particle Size and Content
PublikacjaAgricultural waste is a still untapped source of materials that can, in case of proper utilization, significantly improve the sustainability of polymers and their composites. In this work, polymer composites based on isotactic polypropylene were produced incorporating ground sunflower husk in the amount of 10 wt% and 20 wt%. The work’s main objective is to evaluate how preliminary fractioning of this agricultural waste filler affects...
-
The role of additives in improving the flammability and calorific value of leather shavings and the binding of chromium compounds in ash
PublikacjaLeather processing companies are struggling with the problem of increasing costs of post-production waste disposal. Therefore, the issue of thermal waste disposal at the plant and the use of generated heat in the production process is becoming more and more popular. Leather waste on its own does not allow for autothermal combustion despite the sufficient higher heating value (HHV). Therefore the Authors proposed to improve the...
-
Experimental investigation and process parameter optimization of sheet metal bending by line heating method
PublikacjaThe present study is concerned with the experimental investigation of sheet metal deforming by line heating method that incorporates the combined effect of traverse speed of the torch, thickness of the sheet metal, and the number of passes of the torch. For the numerical analysis of metal bending by line heating, the
-
Effect of Thermal Treatment of Birch Wood by Saturated Water Vapor on Granulometric Composition of Chips from Sawing and Milling Processes from the Point of View of Its Processing to Composites
PublikacjaThe goal of this work is to investigate the impact of thermal modification of birch wood with saturated steam on the particle size distribution of the sawing and milling process. Birch wood (Betula pendula Roth) is an excellent source to produce plywood boards. Wastes from mechanical processing of birch wood are suitable to produce composite materials. Granulometric analyses of chips from sawing processes on the PRW 15M frame saw,...
-
Wstępne badania technologii spawania złączy narożnych ze stali niskoweglowej i nierdzewnej o grubości g=6mm i g=10mm
PublikacjaCelem pracy był dobór parametrów spawania dla spoin narożnych o grubości 6mm i 10mm próbek wykonanych ze stali niskowęglowej S355 i stali nierdzewnej - typu 304 (X6CrNI18-10). Złącza były spawane laserowo, jednostronnie z pełnym przetopem a powierzchnie lica i grani zapewniają uzyskanie szczelności przylegającego elementu uszczelniającego. Próbki zostały dostarczone przez Zleceniodawcę. Próby zostały przeprowadzone na stanowisku...
-
Sounding rocket temperature and heat transfer data
Dane BadawczeThis dataset contains temperature and heat transfer data measured during REXUS 25 sounding rocket HEDGEHOG Experiment launched from Esrange Space Centre, Kiruna, Sweden. For experiment details, please see:
-
Cement kiln dust
PublikacjaThe volume of cement production in the world has remained at the level of approxi mately 4.1 billion tons/year. The cement production process is energy intensive and is the world’s leading emitter of carbon dioxide. Therefore, the main activities cement plants are aimed at introducing technologies changes in production of clinkier.The construction industry is responsible for the majority of CO2 emissions to the atmosphere: the...
-
XRD-TiO2 heat-treated at 400-600oC in Ar or H2
Dane BadawczeThese data contain XRD patterns of TiO2 heat-treated at 400-600oC in Ar or H2. Two pases of TiO2 were identified: anatase and rutile.
-
The topography of as-quenched and heat treated 58(2Bi2O3-V2O5)-42SrB4O7 glasses measured with confocal microscope
Dane BadawczeThe topography of as-quenched and heat treated 58(2Bi2O3-V2O5)-42SrB4O7 glasses measured with confocal microscope.
-
Analytical and reliability data from the real-time simulator biogas plant
Dane BadawczeThe dataset represents the results of biogas plant simulation. The described plant is an agricultural biogas system, which can produce electrical energy with power estimated up to 1070 kW and heat energy that can reach 1200 kW simultaneously.
-
The morphology of as-quenched and heat treated 58(2Bi2O3-V2O5)-42SrB4O7 glasses measured with AFM
Dane BadawczeThe morphology of as-quenched and heat treated 58(2Bi2O3-V2O5)-42SrB4O7 glasses was measured with the use of atomic force microscope.
-
EPR of TiO2 hydrogenated at 500 and 600oC
Dane BadawczeData contain EPR spectra of TiO2 (anatase phase) heat treated in H2 at 500 and 600oC. Sample heated at 500oC contained 4 wt% of rutile and that at 600oC 8 wt% of rutile.
-
XPS-TiO2 heated in H2
Dane BadawczeThese XPS spectra were recorded for TiO2 heat-treated at 450-600oC in H2. Surface oxygen groups were determined. Deconvolution of Ti 2p peak allowed to determine Ti3+ on the titania surface.
-
SEM of TiO2 heated at 400-600oC in Ar or H2
Dane BadawczeData contain some SEM images of TiO2 taken after its heat treatment in Ar or H2 at 400-600oC. Treated TiO2 was crystalline anatase phase with 3-4 % of rutile nclei.
-
Results of implementation of Feed Forward Neural Networks for modeling of heat transfer coefficient during flow condensation for low and high values of saturation temperature
Dane BadawczeThis database present results of implementation of Feed Forward Neural Networks for modeling of heat transfer coefficient during flow condensation for low and high values of saturation temperature. Databse contain one table and 7 figures.
-
Diagnostyka eksploatacyjna okrętowych silników spalinowych - tłokowych i turbinowych
PublikacjaW monografii przedstawiono wybrane zagadnienia diagnostyki technicznej silników spalinowych dużej mocy, zarówno tłokowych, jak i turbinowych, ukierunkowane na eksploatację okrętowych (i nie tylko) systemów energetycznych, w których występują tego typu silniki. W początkowej części opracowania zaproponowano koncepcję systemowego ujęcia diagnostyki eksploatacyjnej silników okrętowych w aspekcie obowiązujących standardów światowych...
-
Numerical simulation of cold flow and combustion in a swirl stabilized combustor
PublikacjaA numerical simulation model was developed to investigate the cold flow and combustion using Ansys FLUENT 2021R1. The governing equations were solved using the pressure-based method, and pressure–velocity coupling was performed using the SIMPLE method. To model the turbulent process, the RSM model was used. Non-premixed model is chosen to solve the chemical kinetics between fuel and oxigen. Radiation heat transfer was calculated...