Wyszukiwarka
Filtry
wszystkich: 674
wybranych: 436
Wyniki wyszukiwania dla: PLATE
-
Detection of damages in a rivetted plate
PublikacjaThe paper presents the results of damage detection in a riveted aluminium plate. The detection method has been based on Lamb wave propagation. The plate has been analysed numerically and experimentally. Numerical calculations have been carried out by the use of the time-domain spectral finite element method, while for the experimental analysis laser scanning Doppler vibrometry (LSDV) has been utilised. The panel has been excited...
-
Investigation of microstructure of D36 Plate
PublikacjaWykonano badania metalograficzne i określono strukturę blachy gatunku D36.
-
Experimental study on plate modal parameters
PublikacjaTest doświadczalny jest częścią systemu diagnostycznego. Autorzy badają wpływ dodatkowej masy na parametry modalne wolno popartej stalowej płytyi. Artykół przedstawia technikę wyznaczania parametrów modalnych dla systemów monitorowania konstrukcji.The experimental test introduced in the paper is the part of the diagnostic system. The authors investigate the influence of the additional mass on modal parameters of simply supported...
-
Numerical simulation of hardening of concrete plate
PublikacjaThe paper presents a theoretical formulation of concrete curing in order to predict temperature evolution and strength development. The model of heat flow is based on a well-known Fourier equation. The numerical solution is implemented by means of the Finite Difference Method. In order to verify the model, the in situ temperature measurements at the top plate of a road bridge were carried out. A high agreement between numerical...
-
EVALUATION OF CAUSES OF CORROSION OF PLATE HEATEXCHANGER
PublikacjaPrzeprowadzono analizę zniszczeń korozyjnych wykrytych na płycie wymiennika ciepła stosowanego do chłodzenia silnika głównego statku. Stwierdzono obecność wżerów korozyjnych oraz korozji szczelinowej. Przedstawiono możliwe przyczyny wystąpienia w.w. uszkodzeń.
-
Study of a plate modelling a dock gate
Publikacja -
Torque Transmitted by Multi-plate Wet Clutches in Relation to Number of Friction Plates and Their Dimensions
PublikacjaIn the paper results of experimental tests on multi-plate wet clutch torque capacity for various diameters and numbers of friction plates are presented. Construction of an apparatus for laboratory tests of wet clutch engagement, drag torque and maximum torque is shown. Methodology of maximum torque capacity experiment and hydraulic circuit diagram, which supplies a motor and an actuator for the experiment are described. Analytically...
-
Bending of a Three-Layered Plate with Surface Stresses
PublikacjaWe discuss here the bending deformations of a three-layered plate taking into account surface and interfacial stresses. The first-order shear deformation plate theory and the Gurtin-Murdoch model of surface stresses will be considered and the formulae for stiffness parameters of the plate are derived. Their dependence on surface elastic moduli will be analyzed.
-
A non-linear direct peridynamics plate theory
PublikacjaIn this paper a direct non-local peridynamics theory for thin plates is developed. Peridynamic points are assumed to behave like rigid bodies with independent translation and finite rotation degrees of freedom. The non-local mechanical interaction between points is characterized by force and moment vectors. The balance equations including the linear momentum, the angular momentum and the energy are presented. Peridynamic deformation...
-
Emissivity of the one-plate lapping machine tool
PublikacjaPrzedstawiono wyniki badań własnych emisyjności docieraka żeliwnego docierarki jednotarczowej. Omówiono konstrukcje produkowanych docierarek jednotarczowych wyposażonych w system kontroli temperatury lub chłodzenia tarczy docierającej. Podano warunki pomiarów temperatury przy użyciu kamery termowizyjnej typu V-20II firmy VIGO System S.A.
-
Wave propagation in plate structures for crack detection
Publikacja -
Wave propagation in plate structures for crack detection.
PublikacjaW pracy przedstawiono analizę propagacji fali poprzecznej w płycie z pęknięciem. Do modelowania zagadnienia zastosowano metodę elementów spektralnych.
-
Viscoplastic analysis of damped vibrations of circular plate
PublikacjaGłównym celem artykułu jest przedstawienie procedury do nieliniowej statycznej i dynamicznej analizy MES z lepkoplastycznym prawem Bodnera-Partoma. Przedstawione są podstawowe równania modelu konstytutywnego wraz z koncepcją implementacji do komercyjnego programu MSC.Marc przy użyciu procedury UVSCPL. Przedstawiono przykład analizy numerycznej płyty kołowej, zweryfikowany eksperymentalnie. Dodatkowo przedstawiono koncepcje wyznaczania...
-
Elastic Wave Propagation in a Cracked Isotropic Plate
PublikacjaW pracy omówiono model spektralny izotropowej płyty z peknięciem służący do analizy propagacji fali spręzystej.
-
Evaluating the influence of radiative heat flux on convective heat transfer from a vertical plate in air using an improved heating plate
PublikacjaThis article examines the influence of radiative heat flux on the accuracy of the results of free convective heat transfer in air. In order to carry out these tests, based on the experience gained during the operation of a plate heated on one side, compensated by a reverse heat loss flux counter-heater, a unique double-sided heating sandwich plate was designed and built, consisting of three thin epoxy resin plates reinforced with...
-
Medially positioned plate in first metatarsophalangeal joint arthrodesis
PublikacjaObjective The purpose of this study was to biomechanically compare the stability of first metatarsophalangeal (MTP1) joint arthrodesis with dorsally and medially positioned plates. Methods A physical model of the MTP1 joint consists of printed synthetic bones, a titanium locking plate and screws. In the experiments, samples with dorsally and medially positioned plates were subjected to loading of ground load character in a universal...
-
Influence of Holes Manufacture Technology on Perforated Plate Aerodynamics
PublikacjaTranspiration flow is a very important and still open subject in many technical applications. Perforated walls are useful for the purpose of “flow control”, as well as for the cooling of walls and blades (effusive cooling) in gas turbines. We are still not able to include large numbers of holes in the numerical calculations and therefore we need physical models. Problems are related also to the quality of the holes in perforated...
-
Disturbances of magnetic field in surrounding of mobile, metalic plate
PublikacjaThe uniform magnetic field of the Earth in the surrounding of a mobile, metalic object undergoes deformation by eddy currents. The influence of the moving conducting object on total magnetic field of the Earth depends on the object's shape, position and speed of the changes relative to the magnetic field's vector of the Earth as well as the electric conductivity and the relative magnetic permeability of the material. The disturbances...
-
Identification of plate dynamic parameters for structural health monitoring
PublikacjaPraca przedstawia technikę wyznaczania parametrów modalnych wykorzystywanych w diagnostyce konstrukcji. Modalna masa, sztywność, tłumienie i postacie drgań wyznaczone są dla prostokątnej stalowej płyty na podstawie badań eksperymentalnych. Teoretyczne parametry modalne otrzymaneo z modelu MES. Omówiony został wpływ dodatkowej masy na parametry modalne konstrukcji.This paper presents a technique for modal parameters estimation for...
-
Bead-on-Plate Underwater Wet Welding on S700MC Steel
PublikacjaThe participation of high strength steels in marine and offshore structures is increasing, which makes it necessary to develop recommendations for underwater repair welding works. The article presents the results of bead-on-plate welded specimens made of S700MC high strength steel in underwater wet welding conditions by covered elec- trodes. Three specimens with heat input values in the range 0.91-1.05 kJ/mm were made. The specimens...
-
Active Damping of Impulse-Excited Flexible Plate Vibration
PublikacjaArtykuł prezentuje metodę aktywnego tłumienia drgań podatnej płytki wzbudzanych impulsowo. Układ sterowania składa się z aktywych wzbudników piezoelektrycznych przymocowanych do przedmiotu. Efektywnośc metody została potwierdzona badaniami eksperymentalnymi.
-
Modeling of damage in a circular plate subjected to dynamic excitation
PublikacjaSzereg różnych dziedzin nauki zajmuje się problemem zniszczenia ciśnieniowych metalowych zbiorników (mechanika, termodynamika, mechanika płynów). Tylko niektóre prace ujmują wszystkie aspekty analizy. W prezentowanej pracy przedstawiono numeryczna analizę metalowej płyty poddanej obciążeniu dynamicznemu, aż do momentu zniszczenia. Do analizy zastosowano program MSC.Marc, element powłokowy, i prawo sprężysto lekoplastyczne uwzględniające...
-
On Von Karman Equations and the Buckling of a Thin Circular Elastic Plate
PublikacjaWe shall be concerned with the buckling of a thin circular elastic plate simply supported along a boundary, subjected to a radial compressive load uniformly distributed along its boundary. One of the main engineering concerns is to reduce deformations of plate structures. It is well known that von Karman equations provide an established model that describes nonlinear deformations of elastic plates. Our approach to study plate deformations...
-
Modeling of lapping plate wear and conditioning in single-sided lapping
PublikacjaIn order to achieve higher quality on worked surfaces with lower roughness, very high accuracy of shape and dimensions it is crucial to improve conventional finishing technologies and to develop new working principles. Single-sided lapping is one of the most effective planarization technologies and it is determined by a number of factors and boundary conditions. The most significant influence over a dimensional and profile accuracy,...
-
Reliability of Corroded Stiffened Plate Subjected to Uniaxial Compressive Loading
PublikacjaThe work is focused on the reliability of corroded stiffened plates subjected to compressive uniaxial load based on the progressive collapse approach as stipulated by the Common Structural Rules for Bulk Carriers and Oil Tankers, employing the limit state design. Two different cases have been investigated. In the first model, the corrosion degradation led to uniform thickness loss, whereas the mechanical properties were unchanged,...
-
Damage localisation in a stiffened plate structure using a propagating wave
PublikacjaThe paper presents an application of changes in propagating waves for damage detection in a stiffened aluminium plate. The experimental investigation was conducted on an aluminium plate with riveted two L-shape stiffeners. The wave has been excited with a piezoelectric transducer and measured with the Laser Scanning Doppler Vibrometer. Recorded signals were analysed using the special signal processing techniques developed for damage...
-
Selected studies of flow maldistribution in a minichannel plate heat exchanger
PublikacjaAnalysis of the state of-the-art in research of minichannel heat exchangers, especially on the topic of flow maldistribution in multiple channels, has been accomplished. Studies on minichannel plate heat exchanger with 51 parallel minichannels with four hydraulic diameters, i.e., 461 μm, 574 μm, 667 μm, and 750 μm have been presented. Flow at the instance of filling the microchannel with water at low flow rates has been visualized. The...
-
Uncertainty of the liquid mass flow measurement using the orifice plate
PublikacjaThe article presents an estimation of measurement uncertainty of a liquid mass flow using the orifice plate. This subject is essential because of the widespread use of this type of flow meters. Not only the quantitative estimation but also the qualitative results of those measurements are important. To achieve these results the authors of the paper propose to use the theory of uncertainty. The article shows the analysis of the...
-
NONLINEAR VIBRATION ANALYSIS OF BEAM AND PLATE WITH CLOSED CRACK: A REVIEW
PublikacjaThe effect of nonlinearity is high sensitivity in damage detection, especially for closed cracks and delamination. This review illustrates the results of several researchers dealing with nonlinear effects caused by the closure of cracks in the structure, i.e., beam and plate structures. Early detection of damage is an important aspect for the structure and, therefore, continuous progress is being made in developing new and effective...
-
Estimating the uncertainty of the liquid mass flow using the orifice plate
PublikacjaThe article presents estimation of measurement uncertainty of a liquid mass flow using the orifice plate. This subject is essential because of the widespread use of this type of flow meters, which renders not only the quantitative estimation but also qualitative results of this type so those measurements are important. To achieve this goal, the authors of the paper propose to use the theory of uncertainty. The article shows the...
-
Performance of a plate heat exchanger operated with water-Al2O3 nanofluid
PublikacjaThis study is focused on experimental investigation of a selected type of brazed plate heat exchanger (PHEx). The main aim of the paper was to experimentally check the ability of nanofluids to enhance the performance of PHEx. A typical water-Al2O3 nanofluid was tested and compared to that of the base fluid, i.e. water. Nanoparticles were tested at the concentration of 0.1% and 1% by weight. Impact of the 1 day and 3 days break...
-
Performance of a plate heat exchanger operated with water-Al2O3 nanofluid
PublikacjaThis study is focused on experimental investigation of a selected type of brazed plate heat exchanger (PHEx). The main aim of the paper was to experimentally check the ability of nanofluids to enhance the performance of PHEx. A typical water-Al2O3 nanofluid was tested and compared to that of the base fluid, i.e. water. Nanoparticles were tested at the concentration of 0.1% and 1% by weight. Impact of the 1 day and 3 days break...
-
Performance of a plate heat exchanger operated with water-Al2O3 nanofluid
PublikacjaThis study is focused on experimental investigation of a selected type of brazed plate heat exchanger (PHEx). The main aim of the paper was to experimentally check the ability of nanofluids to enhance the performance of PHEx. A typical water-Al2O3 nanofluid was tested and compared to that of the base fluid, i.e. water. Nanoparticles were tested at the concentration of 0.1% and 1% by weight. Impact of the 1 day and 3 days break...
-
Temperature influences on shear stability of a nanosize plate with piezoelectricity effect
PublikacjaPurpose The purpose of this paper is to predict the mechanical behavior of a piezoelectric nanoplate under shear stability by taking electric voltage into account in thermal environment. Design/methodology/approach Simplified first-order shear deformation theory has been used as a displacement field. Modified couple stress theory has been applied for considering small-size effects. An analytical solution has been taken into account...
-
Use of the Delta plate for surgical treatment of patients with condylar fractures
Publikacja -
Spectral plate element for crach detection with use of propagation wares.
PublikacjaW pracy przedstawiono model płyty oparty na metodzie elementów spectralnych. Przedstawiono wyniki analizy interakcji pęknięcia zmęczeniowego i propagującej się fali.
-
Stable and unstable bifurcation in the von Karman problem for a circular plate
PublikacjaW niniejszej pracy badamy równania von Karmana dla cienkiej, sprężystej, kołowej płyty, która znajduje się na sprężystym podłożu, pod działaniem sił ściskających wzdłuż swojego brzegu.Stosując metody analizy nieliniowej, dowodzimy istnienia stabilnychi niestabilnych punktów bifurkacji w zbiorze rozwiązań badanych równań.
-
Detection and size estimation of crack in plate based on guided wave propagation
PublikacjaThe paper presents results of the comprehensive theoretical and experimental investigation of crack detection in metallic plate using guided wave propagation. The main aim of the paper is to develop the novel method which would allow for linear crack size estimation with the use of minimal number of the transducers. In general, there exists the relation between length of the propagation path and the wave amplitude value. However,...
-
CAPABILITY OF IDENTIFYING AND PREDICTING THE TECHNICAL CONDITION OF PLATE HEAT EXCHANGERS IN OPERATION
PublikacjaThe paper presents a test stand for plate heat exchangers, allowing to identify the technical condition and to predict durability of the heat exchangers used aboard the sea-going ships: ”Oceanograf”, ”Władysław Orkan”and a passenger-car ferry, under the condition that they are of the same type and manufactured by the same company. In the first part three different installations with plate heat exchangers in the engine rooms...
-
Applying of thin plate boundary condition in analysis of ship’s magnetic field
PublikacjaThis paper presents computer simulations of ship’s magnetic signatures using a new thin plate boundary condition implemented in the Opera-3d 18R2 program. The paper aims to check the magnetic signatures’ numerical calculations precision of objects using the thin plate boundary conditions and analysis of the magnetic signature of ship with a degaussing system and with and without inner devices.
-
Performance of the flat plate solar collector operated with water-Al2O3 nanofluid
PublikacjaThis paper shows the experimental results of the performance a flat plate solar collector with water-Al2O3 nanofluid as a working fluid. The weight fractions of nanoparticles were 0.1%, 0.2% and 0.4%. The volume flow rate of nanofluid varied from 60 l/h to 170 l/h. The results show that application of nanofluids instead of pure water resulted in higher efficiency of the tested flat plate solar collector for given range of thermal...
-
The Influence of Workpiece Hardness on Plate Temperature during One Side Lapping
PublikacjaLapping leads to a surface with low roughness and high precision. Because of required parts accuracy tool flatness is the key to the successful machining. To avoid its excessive thermal expansion, plate temperature research was taken. The goal was to determine the correlation between the basic lapping conditions and wheel temperature. In work Bulsara et al. authors developed model to estimate the maximum and average temperature...
-
Performance of the flat plate solar collector operated with water-Al2O3 nanofluid
PublikacjaThe paper discusses the effect of application of water-Al2O3 nanofluid, as a working fluid, on the efficiency of a flat plate solar collector. The mass concentration of nanoparticles was 0.1%, 0.2% and 0.4%. The tests were conducted for two values of radiation of about 1050 W/m2 and 400 W/m2, and volume flow rates of 60 l/h, 120 l/h and 170 l/h. The efficiency was calculated according to recommendations of the Polish Standard....
-
Effect of surface roughness on thermal-hydraulic characteristics of plate heat exchanger
PublikacjaIn the paper the experimental analysis of passive heat transfer intensification in the case of modeled plate heat exchanger is conducted. The plate heat exchanger is chosen for the analysis because this kind of heat exchangers could be prospectively applied in the ORC systems, however other areas or application are equally possible. The experimental setup was assembled at the Department of Energy and Industrial Apparatus of Gdansk...
-
Plate heat exchanger with porous structure for potential use in ORC system
PublikacjaThe experimental analysis of passive heat transfer intensification in the case of plate heat exchanger has been carried out. The passive intensification was obtained by a modification of the heat transfer surface, which was covered by a metallic porous microlayer. The experiment was accomplished in two stages. In the first stage the commercial stainless steel gasketed plate heat exchanger was investigated, while in the second one...
-
Plate heat exchanger with porous structure for potential use in ORC system
PublikacjaThe experimental analysis of passive heat transfer intensification in the case of plate heat exchanger has been carried out. The passive intensification was obtained by a modification of the heat transfer surface, which was covered by a metallic porous microlayer. The experiment was accomplished in two stages. In the first stage the commercial stainless steel gasketed plate heat exchanger was investigated, while in the second one...
-
Guided waves for monitoring of plate structures with linear cracks of variable length
PublikacjaDamage occurring at the work of plate structures may grow to a considerable size. The joint action – the detection of a defect at the earliest possible stage, the monitoring of its growth and the determination of its critical size in the context of structural reliability allows optimizing the cost of the maintenance and repair of structural elements. Thus the development of monitoring systems for permanent observation of fault...
-
Heat transfer intensification by enlarged surface roughness in the plate heat exchanger
PublikacjaIn the paper an experimental analysis of passive heat transfer intensification technique employed in the case of the plate heat exchanger is presented. The passive intensification was obtained by a modification of the heat transfer surface. The roughness of surface was increased by a use of glass micro-beads. Single-phase convective heat transfer in the water-water system was studied. The experiment was accomplished in two stages....
-
From monetite plate to hydroxyapatite nanofibers by monoethanolamine assisted hydrothermal approach
Publikacja -
Problems of strength modelling of steel sandwich panels under in-plate load
PublikacjaW pracy omówiono zagadnienia wytrzymałości statycznej stalowych paneli typu sandwich spawanych laserowo. Omówiono charakterystyki sztywności podczas zginania, przedstawiono zachowanie pod obciążeniem równomiernie rozłożonym a także sposób niszczenia pod obciążeniem ściskającym. Omówiono możliwości stosowania takich konstrukcji na podstawie wniosków z badań.