Wyszukiwarka
Filtry
wszystkich: 645
-
Katalog
Wyniki wyszukiwania dla: bi6fe2ti3o18 ceramics
-
Al203 sealing elements lapping
PublikacjaPrzedstawiono wyniki badań własnych wydajnosci docierania ceramiki Al203. Badano elementy uszczelniające na docierarce jednotarczowej o standardowym układzie kinematycznym. Określono wpływ wielkości mikroziaren węglika boru o numerze F400/17, F800/6.5 i F1200/3 oraz wartości nominalnego nacisku jednostkowego na ubytek materiału w czasie 15 i 20 min. Scharakteryzowano mechanizm usuwania naddatku przy docieraniu elementów ceramicznych....
-
Sliding friction of alumina (Al2O3) with friction induced vibrations
Dane BadawczeTest files containing data on experiments in self mated sliding contact of alumina Al2O3 lubricated with either water or paraffin oil. Tests run in variable load/velocity conditions and with different dynamic settings of the test rig (PT-3 tribometer). The aim of the research was to attempt in finding correlations between the dynamic characteristics...
-
Influence of yttria surface modification on high temperature corrosion of porous Ni22Cr alloy
PublikacjaProtective coatings for porous alloys for high temperature use are relatively new materials. Their main drawback is high temperature corrosion. In this work protective coatings based the on Y-precursor infiltrated into the sintered Ni22Cr alloys are studied at 700°C. Effects of the amount of the protective phase on the resulting corrosion properties are evaluated in air and humidified hydrogen. Weight gain of the samples, their...
-
Effects of La Content on the Densification, Microstructure, and Conductivity of Doped La10−x Ge6 O26±δ Electrolytes
PublikacjaIn this study, the influence of La content on the characteristics of Nb-, Mo-, and W-doped LaxGe6O26±δ electrolytes was investigated through sintering study, X-ray diffraction, scanning electron microscopy, and conductivity measurement. The densification of LaxGe5.5Nb0.5O26±δ and LaxGe5.5W0.5O26±δ was retarded as the x reached 9.75, while that of LaxGe5.5Mo0.5O26±δ improved with increasing La content. The average grain size slightly...
-
Nanotubular oxide layers and hydroxyapatite coatings on ‘Ti–13Zr–13Nb’ alloy
PublikacjaThe presented research was aimed to determine the mechanical properties of the nanotubular oxide layer covered with hydroxyapatite coating. The Ti–13Zr–13Nb alloy was oxidised in 1M phosphoric acid with an addition of 0?5% HF for HF solution at 20 V voltage. The electrochemically assisted deposition of hydroxyapatite was performed at cyclic polarisation in NH4H2PO4 and CaCl2 solution at 80uC. The mechanical properties were determined...
-
Method of Monitoring of the Grinding Process with Lapping Kinematics Using Audible Sound Analysis
PublikacjaUtilising microphones as audible sound sensors for monitoring a single-side grinding process with lapping kinematics is presented in the paper. The audible sound generated during grinding depended on the cutting properties of electroplated tools with D107 diamond grains and different thicknesses of the nickel bond. The tool wear affected the obtained technological effects such as material removal rate and the surface roughness...
-
Thermochemical Conversion of Biomass and Municipal Waste into Useful Energy Using Advanced HiTAG/HiTSG Technology
PublikacjaAn advanced thermal conversion system involving high-temperature gasification of biomass and municipal waste into biofuel, syngas or hydrogen-rich gas is presented in this paper. The decomposition of solid biomass and wastes by gasification is carried out experimentally with a modern and innovative regenerator and updraft continuous gasifier, among others. A ceramic high-cycle regenerator provides extra energy for the thermal conversion...
-
2D MXene nanocomposites: electrochemical and biomedical applications
PublikacjaIn recent years, key questions about the interaction of 2D MXene nanomaterials in electrochemical and biomedical applications have been raised. Most research has focused on clarifying the exclusive properties of the materials; however, only limited reports have described the biomedical applications of 2D nanomaterials. 2D MXenes are monolayer atomic nanosheets resulting from MAX phase ceramics. The hydrophilic properties, metallic...
-
Enhancing electrical properties through in-situ controlled nanocrystallization of V2O5–TeO2 glass
PublikacjaV2O5–TeO2 glass–ceramics (VTGC) were prepared by controlled annealing of the V2O5–TeO2 glass (VTG), which illustrates a parent glass matrix with a single charge carrier. The annealing proceeded at six temperatures selected between the glass transition and the maximum of the frst crystallization process to obtain various nanocrystallite sizes. Heat treatment caused an increase in DC conductivity by 2.5–3.5 (250–285 °C) order of...
-
Wojciech Sadowski prof. dr hab. inż.
OsobyWojciech Sadowski (ur. 2.02.1954 r. w Ostaszewie), naukowiec, polski inżynier, profesor Politechniki Gdańskiej, specjalista z fizyki ciała stałego, nanotechnologii, optoelektroniki. Studia wyższe ukończył w 1979 r. w Leningradzkim Instytucie Elektrotechnicznym w Leningradzie w specjalności dielektryki i półprzewodniki, uzyskując tytuł zawodowy magistra inżyniera elektronika. Od 1979 r. pracuje na Politechnice Gdańskiej, pełniąc...
-
Szlifowanie jednostronne z wykorzystaniem ściernic o spoiwie galwanicznym
PublikacjaW referacie przedstawiono wyniki badań eksperymentalnych szlifowania jednostronnego ceramiki tlenkowej Al2O3 z zastosowaniem ściernic o spoiwie galwanicznym z ziarnami diamentowymi D107 i D64. Prototypowe ściernice charakteryzowały się różną wysokością warstwy spoiwa niklowego wpływającą na głębokość i trwałość utwierdzenia ziaren ściernych. Ściernice wykonano dla trzech warto- ści współczynnika hs wysokości warstwy spoiwa w stosunku...
-
Prediction of coking dynamics for wet coal charge
PublikacjaA one-dimensional transient mathematical model describing thermal and flow phenomena during coal coking in an oven chamber was studied in the paper. It also accounts for heat conduction in the ceramic oven wall when assuming a constant temperature at the heating channel side. The model was solved numerically using partly implicit methods for gas flow and heat transfer problems. The histories of temperature, gas evolution and internal...
-
High-temperature properties of titanium-substituted yttrium niobate
Publikacjahe defect fluorite titanium-doped yttrium niobate samples Y3Nb1−xTixO7−δ have been synthesized and investigated by the means of high-temperature X-ray diffraction, dilatometry, and thermogravimetry. Thermal expansion coefficients (TECs) as well as chemical expansion coefficients for material with 5, 10, and 15 mol% of titanium were determined. All investigated samples exhibit chemical contraction caused by Ti doping. The values...
-
Applications of Additively Manufactured Tools in Abrasive Machining—A Literature Review
PublikacjaHigh requirements imposed by the competitive industrial environment determine the development directions of applied manufacturing methods. 3D printing technology, also known as additive manufacturing (AM), currently being one of the most dynamically developing production methods, is increasingly used in many different areas of industry. Nowadays, apart from the possibility of making prototypes of future products, AM is also used...
-
Microstrip line with short-circuited edge as a high-pass filter operating up to millimeter-wave frequencies
PublikacjaPrzedstawiono prosty planarny filtr górnoprzepustowy wykorzystujący linię mikropaskową ze zwartym brzegiem. Układy zaprojektowano w taki sposób, aby pasmo przepustowe rozpoczynało się w zakresie K lub Ka. Wykonano dwa prototypy: na podłożu w postaci warstwy dielektrycznej wykonanej z ceramiki alundowej oraz na podłożu organicznym o niskiej przenikalności elektrycznej. Wykazano dużą zgodność teoretycznych i pomierzonych charakterystyk...
-
Łożyska ślizgowe smarowane wodą
PublikacjaŁożyska ślizgowe smarowane wodą wykonywane są obecnie z kompozytów polimerowych, kompozytów gumowych, kompozytów metalowych i ceramiki. Najczęściej z kompozytów polimerowych, przy czym znacznie rośnie udział materiałów ceramicznych. Przedstawiono przegląd konstrukcji łożysk ślizgowych smarowanych wodą i rodzajów stosowanych przez światowe firmy materiałów na łożyska. Opisano unikatowe rozwiązanie konstrukcyjne poprzecznego, klockowego...
-
Fast impedance measurement method using Laplace transformation
PublikacjaArtykuł przedstawia metodę pomiaru impedancji wykorzystującą rzeczywisty uskok jednostkowy step jako sygnał pobudzenia i transformację Laplace jako narzędzie analizy sygnału odpowiedzi testowanego obiektu. Metoda jest dedykowana do badania różnych obiektów technicznych (np. powłok antykorozyjnych, czujników gazu, ceramik, tkanek biologicznych itp.) gdy czas pomiaru nie może być długi. Przedstawiona metoda jest znana ale niezbyt...
-
Electrical and noise responses of the ink-printed WS2-based gas sensor for sensing mixtures of NO2 and NH3 under UV light (275 nm)
Dane BadawczeThe data set consists of results collected for the resistive gas sensor composed of 2D flakes of tungsten disulfide (WS2) printed on the ceramic substrate: 1) time-resolved DC resistance measurements and 2) low-frequency noise measurements realized in the dark and under UV light assistance (275 nm) for selected gas atmospheres (NO2 and NH3 as target...
-
Thermoelectric and electrical transport properties of mixed-conducting multicomponent oxides based on Ba(Zr,Ce)O3-δ
PublikacjaIn this work, the chosen physicochemical properties of single-phase multicomponent oxides BaTi1/8Fe1/8Co1/8Y1/8Zr1/8Sn1/8Ce1/8Hf1/8O3-δ and BaTi1/9Fe1/9Co1/9Y1/9Zr1/9Sn1/9Ce1/9 Hf1/9Bi1/9O3-δ were studied. The microstructure of the compounds strongly depended on the presence of bismuth in the structure. The electrical transport studies showed a level of electrical conductivity of ∼10−3 - 10−2 S/cm in the temperature range 673–1073...
-
Green engineered biomaterials for bone repair and regeneration: Printing technologies and fracture analysis
PublikacjaDespite the exceptional self-regeneration properties of bone, severe injuries often require additional surgical intervention such as using artificial bone constructs. These structures need to meet a number of criteria regarding their structure, performance, alongside the rate and the mechanism of erosion and fracture when implanted, for stimulating the regeneration of defected bone and, more critically providing support in the...
-
Influence and development of new kinematic systems in flat surface lapping
PublikacjaThe face grinding and lapping technology is widely used in the field of the precise and ultraprecise manufacturing. It has become an indispensable technology in the manufacture of many parts. An absence of material restrictions allows machining both metal and non-metallic materials, including technical ceramics [1]. Nowadays there are mainly two kinematic systems in lapping machines [2]. The machining plane-parallel surfaces is...
-
Reducing common mode voltage and bearing currents in quasi - resonant DC - link inverter
PublikacjaIn the paper, a concept of separation of an inverter-fed induction motor drive from its mains supply by two transistor switches inserted in the dc-link circuit is reexamined based on the proposed parallel quasi-resonant dc-link inverter (PQRDCLI). The objective of the paper is to show an advantage of the proposed topology in limiting high frequency common mode voltage and bearing currents. In the laboratory setup, an induction...
-
Influence of silver nanoparticles addition on antibacterial properties of PEO coatings formed on magnesium
PublikacjaMagnesium is a biodegradable material and thus could be a choice for bone fixation devices and implants with a specific purpose. This study aims to enhance the anti-corrosive, biocompatible, and antibacterial properties on magnesium-based materials through ceramic coatings formation. To achieve this the silicate-based electrolyte was used to create of Plasma Electrolytic Oxidation (PEO) coatings. During investigation the bioactive...
-
Electrodeposited Biocoatings, Their Properties and Fabrication Technologies: A Review
PublikacjaCoatings deposited under an electric field are applied for the surface modification of biomaterials. This review is aimed to characterize the state-of-art in this area with an emphasis on the advantages and disadvantages of used methods, process determinants, and properties of coatings. Over 170 articles, published mainly during the last ten years, were chosen, and reviewed as the most representative. The most recent developments...
-
PoRaCoat Innowacyjna powłoka stentu z kompleksem polifenol-rapamycyna o ulepszonych właściwościach uwalniania leku w celu zwalczania restenozy
ProjektyProjekt realizowany w Laboratorium Materiałów Funkcjonalnych ETI
-
Structure and hyperfine interactions in Bi1−xNdxFeO3 solid solutions prepared by solid-state sintering
PublikacjaThe series of polycrystalline ceramic powders, Bi1xNdxFeO3 (x = 0.11) was successfully synthesized by mixed oxide method followed by pressureless sintering. X-ray diffraction and Mössbauer spectroscopy were used as complementary methods to study structure and hyperfine interactions of the samples. It was found that with an increase of Nd content, within the range of x = 0.20.3 a structural phase transition from rhombohedral to...
-
Potentiometric Oxygen Sensor with Solid State Reference Electrode
PublikacjaThe concentration or the partial pressure of oxygen in an environment can be determined using different measuring principles. For high temperature measurements of oxygen, ceramic-based sensors are the most practical. They are simple in construction, exploration and maintenance. A typical oxygen potentiometric sensor consists of an oxygen ion conducting solid electrolyte and two electrodes deposited...
-
The Effect of Sodium Tetrafluoroborate on the Properties of Conversion Coatings Formed on the AZ91D Magnesium Alloy by Plasma Electrolytic Oxidation
PublikacjaMagnesium and its alloys are widely used in many areas because of their light weight, excellent dimensional stability, and high strength-to-weight ratio. However, the material exhibits poor wear and corrosion resistance, which limits its use. Plasma electrolytic oxidation (PEO) is an effective surface modification method for producing ceramic oxide layers on Mg and their alloys. The influence of the additions of sodium tetrafluoroborate...
-
Design of an Autonomous IoT Node Powered by a Perovskite-Based Wave Energy Converter
PublikacjaThis paper presents the results of experimental research focused on wave energy harvesting and its conversion to power Internet of Things (IoT) devices. The harvesting and conversion process was performed using a wave energy converter (WEC) consisting of a lead zirconate titanate piezoelectric ceramic perovskite material and a prototype power electronic circuit. The designed WEC was considered as a power supply for an end node...
-
Improvement of the Chimney Effect in Stack Ventilation
PublikacjaThe article is focused on the airflow in a ventilation system in a building. The work examines the methods which enhance the chimney effect. In this paper, three cases with different chimneys were analyzed for the full-scale experiment. These cases were characterized by different geometrical and material parameters, leading to differences in the intensity of the ventilation airflow. The common denominator of the cases was the room...
-
New insights on lithium storage in silicon oxycarbide/carbon composites: Impact of microstructure on electrochemical properties
PublikacjaIn this work, we study the impact of the preceramic precursor vinyltriethoxysilane (VTES) on the electrochemical performance of silicon oxycarbide (SiOC) glass/graphite composites. We apply an innovative approach based on high-power ultrasounds in order to obtain highly homogenous composites with a uniform distribution of small graphitic flakes. This procedure enhances gelation and drying of VTES-based preceramic polymer/graphite...
-
Composite Materials Based on Silicon Oxycarbide as Anodes for Lithium-Ion Batteries
PublikacjaIn this work, the properties of binary SiOC/graphite and SiOC/tin, as well as ternary SiOC/graphite/tin obtained from various preceramic precursors are described. During the first step, the materials were synthesized using various techniques such as sol-gel and hydrosilylation. To prevent sedimentation and agglomeration of graphite particles during the gelation stage without using surfactants and thickeners, a new gelation technique...
-
Investigation of the thermal conductivity of λ gypsum using the hot wire method
Dane BadawczeAn experimental study was conducted to determine the thermal conductivity coefficient λ using the ‘hot wire’ method for a building material. Gypsum specimens measuring 400 x 60 x 50 mm were made for the experiment. Along the long axis of the model, an insulated resistance wire with a diameter of 0.2 mm was poured into the gypsum slurry in the centre...
-
Time-frequency analysis in optical coherence tomography for technical objects examination
PublikacjaOptical coherence tomography (OCT) is one of the most advanced optical measurement techniques for complex structure visualization. The advantages of OCT have been used for surface and subsurface defect detection in composite materials, polymers, ceramics, non-metallic protective coatings, and many more. Our research activity has been focused on timefrequency spectroscopic analysis in OCT. It is based on time resolved spectral analysis...
-
Recycling of Industrial Waste as Soil Binding Additives—Effects on Soil Mechanical and Hydraulic Properties during Its Stabilisation before Road Construction
PublikacjaTo improve the in situ soil stabilization, different chemical additives are used (ion exchange compounds, additives based on H2SO4 or vinyl polymers, and organic additives using lignosul- fonates). One interesting alternative is the production of additives from various waste materials. The extensive testing of waste-based blends with soil was performed; the mechanical (unconfined compressive strength (UCS)) and hydraulic (capillary...
-
Microgrinding with single-disk lapping kinematics.
PublikacjaGrinding operations are carried out with a variety of tool-workpiece configurations. The selection of a grinding process for a particular application depends on part shape, part size, ease of fixture, requirements concerning the acceptable shape errors. It is evident that lapping is very effective in eliminating the waviness while surface grinding is not. Dual disk machines for the double face grinding with planetary kinematics...
-
Protective and Suppressing Electromagnetic Interference Properties of Epoxy Coatings Containing Nano-Sized NiZn Ferrites
PublikacjaNano-crystalline ferrites with the chemical formula NixZn(1−x)Fe2O4, where x = 0, 0.2, 0.4, 0.6, 0.8, 1.0, were synthesized using a co-precipitation method. The obtained ferrites were investigated by X-ray diffraction (XRD). The corrosion inhibiting behavior of nano-sized ferrites was tested using carbon steel samples and 10% aqueous ferrite extracts. Results were compared with previous data obtained for micro-sized ceramic ferrites....
-
In Vitro Biological Characterization of Silver-Doped Anodic Oxide Coating on Titanium
PublikacjaDespite the high biocompatibility and clinical effectiveness of Ti-based implants, surface functionalization (with complex osteointegrative/antibacterial strategies) is still required. To enhance the dental implant surface and to provide additional osteoinductive and antibacterial properties, plasma electrolytic oxidation of a pure Ti was performed using a nitrilotriacetic acid (NTA)-based Ag nanoparticles (AgNP)-loaded calcium–phosphate...
-
Optical low-coherence interferometry for selected technical applications
PublikacjaW artykule przedstawiono teoretyczne podstawy optycznej interferometrii niskokoherentnej i przedyskutowano jej unikatowe właściwości. Opisano w nim opracowany przez autorów system OCT przeznaczony do badań strukturalnych materiałów technicznych. Badania te obejmują także zmiany stanu polaryzacji promieniowania rozproszonego w badanym obiekcie. W artykule zawarto wyniki badań wybranych materiałów silnie rozpraszających promieniowanie...
-
The influence oil additives on spread cracks in silicon nitride
PublikacjaThe paper presents an experimental study of the influence of oil additives (Cl, S, P, cerium dioxide (CeO2)) on spread cracks in silicon nitride. The additives Cl, S, P are bound in molecules in liquid form soluble in the base oil. The CeO2 is purely in powder form in suspension. The use of CeO2 powder was made based on the good results of polishing of silicon nitride. A ceramic angular contact ball bearing was modelled using a...
-
EMPROP Metoda elektromagnetyczna estymacji stopnia penetracji propantu w procesie szczelinowania
ProjektyProjekt realizowany w Wydział Chemiczny z dnia 2014-11-25
-
Damage detection in 3D printed plates using ultrasonic wave propagation supported with weighted root mean square calculation and wavefield curvature imaging
Publikacja3D printing (additive manufacturing, AM) is a promising approach to producing light and strong structures with many successful applications, e.g., in dentistry and orthopaedics. Many types of filaments differing in mechanical properties can be used to produce 3D printed structures, including polymers, metals or ceramics. Due to the simplicity of the manufacturing process, biodegradable polymers are widely used, e.g., polylactide (polylactide...
-
RCS Enhancement of Millimeter Wave LTCC Van Atta Arrays With 3-D Printed Lenses for Chipless RFID Applications
PublikacjaIn this paper, we present a new method to enhance the radar- cross section (RCS) of Van Atta arrays which can be used in chipless radio-frequency identification tags operating in millimeter wave frequency bands. Small planar Low-Temperature Co-fired Ceramic (LTCC) Van Atta arrays, that are durable and can operate in harsh environments, are combined with 3-D printed lenses to increase or modify the shape of their RCS by up to 10...
-
Wpływ parametrów docierania na jakość powierzchni powłok Cr2O3.
PublikacjaPrzedmiotem niniejszej rozprawy doktorskiej były badania wpływu wybranych parametrów docierania na jakość powłoki ceramiki Cr2O3. Analizowano wpływ wielkości ziarna, nacisków, prędkości i czasu docierania na wartości parametrów chropowatości powierzchni i ubytek liniowy powłoki ceramicznej nałożonej metodą plazmową na podłoże stalowe. Badania realizowano wg planowanego eksperymentu na docierarce jednotarczowej ze standardowym (pierścieniowym)...
-
Electrical and noise responses of the ink-printed MoS2-based gas sensor for sensing of NO2, NH3 and C3H6O under UV light (275 nm)
Dane BadawczeThis data set consists of DC data, low-frequency noise spectra data and UV-vis spectroscopy data collected for ink-printed MoS2-based resistive sensors (2D MoS2 overlapping flakes creating a continuous layer on the ceramic substrate). The sensors were investigated toward three target gases - nitrogen dioxide (1-10 ppm), ammonia (2-12 ppm) and acetone...
-
Arkadiusz Dawczak
Osoby -
Aleksandra Teresa Wiśniewska dr inż.
Osobyeducation Postgraduate studies in “ Scandinavian Studies“ University of Gdańsk (2019-2020), Postgraduate studies in "Research Project Management and Commercialization of Research Results" Gdańsk University of Technology, Faculty of Management and Economics (2010–2011), Postgraduate studies "Control & Management of Lean Manufacturing in Network Systems", Fachhochschule Karlsruhe (1998–2000), Master's studies "Automation...
-
Injectable biocomposite cement: A dual-setting formula with magnesium potassium phosphate and κ-carrageenan hydrogel for orthopedic advancements
PublikacjaMagnesium phosphate-based cements are highly regarded for their bioactive properties, making them excellent candidates as bone substitutes. Despite their promising attributes, challenges such as high reaction temperature, limited injectability, and brittleness limit their application. This study introduces a dual-setting biocomposite cement, which encompasses both cement hydration and hydrogel's cross-linking. The composition features...
-
Reduction in Errors in Roughness Evaluation with an Accurate Definition of the S-L Surface
PublikacjaCharacterization of surface topography, roughly divided into measurement and data analysis, can be valuable in the process of validation of the tribological performance of machined parts. Surface topography, especially the roughness, can respond straightly to the machining process and, in some cases, is defined as a fingerprint of the manufacturing. When considering the high precision of surface topography studies, the definition...
-
Preparation of MnCo2O4 and Mn1.7CuFe0.3O4 single-layer, and novel MnCo2O4/ Mn1.7CuFe0.3O4 dual-layer spinel protective coatings on complex-shaped metallic interconnects by EPD method
PublikacjaCeramic protective coatings applied to metallic interconnects play a vital role in solid oxide cells (SOCs) preventing interconnect degradation. In this study, uniform, dense, and crack-free single-layer coatings of MnCo2O4, Mn1.7CuFe0.3O4, and dual-layer coatings of MnCo2O4/ Mn1.7CuFe0.3O4 spinel are deposited onto complex-shaped metallic interconnect using electrophoretic deposition (EPD) method. The porosity of sintered MnCo2O4...