Publikacje
Filtry
wszystkich: 306
Katalog Publikacji
Rok 2024
-
Characterization of Corrosion-Induced Fracture in Reinforced Concrete Beams Using Electrical Potential, Ultrasound and Low-Frequency Vibration
PublikacjaThe paper deals with the non-destructive experimental testing of the reinforced concrete beams under progressive corrosion. A series of experiments using electrical potential, ultrasound and low-frequency vibrations techniques are reported. Electrical potential and natural frequencies were used to characterise and monitor the corrosion process at its initial state. The P-wave velocity measurements were proved to be effective in...
-
Charge density wave, enhanced mobility, and large nonsaturating magnetoresistance across the magnetic states of HoNiC2 and ErNiC2
PublikacjaWe report on magnetotransport and thermoelectric properties of two ternary carbides HoNiC2 and ErNiC2 hosting both charge density wave and long-range magnetic order. In the charge density wave state, both compounds show relatively large magnetoresistance MR ≈ 150% in HoNiC2 and ≈ 70%in ErNiC2 at a magnetic field of 9 T and temperature as low as 2 K. This positive field-linear magnetoresistance shows no signatures of saturation....
-
Controlling the europium oxidation state in diopside through flux concentration
PublikacjaThis paper explores the connection between the H3BO3 flux concentration and the co-existence of Eu2+ and Eu3+ dopants within CaMgSi2O6 crystals (diopside). The samples were synthesised using a solid-state synthesis method under varying atmospheric conditions, including oxidative (air), neutral (N2), and reductive (H2/N2 mixture) environments. Additionally, some materials underwent chemical modification by partially substituting...
-
Correlations of structural, thermal and electrical properties of sodium doped complex borophosphosilicate glass
PublikacjaBorophosphosilicate glasses with varying sodium ion concentrations were investigated for their, structural, thermal, and electrical properties. All the obtained glasses were transparent except the glass with the highest sodium content, which exhibited translucency due to inhomogeneities. Increasing sodium content led to reduced boron and silicon content while maintaining a constant B/Si ratio, indicating progressive depolymerization...
-
Cytocompatibility, antibacterial, and corrosion properties of chitosan/polymethacrylates and chitosan/poly(4‐vinylpyridine) smart coatings, electrophoretically deposited on nanosilver‐decorated titania nanotubes
PublikacjaThe development of novel implants subjected to surface modification to achieve high osteointegration properties at simultaneous antimicrobial activity is a highly current problem. This study involved different surface treatments of titanium surface, mainly by electrochemical oxidation to produce a nanotubular oxide layer (TNTs), a subsequent electrochemical reduction of silver nitrate and decoration of a nanotubular surface with...
-
Detailed studies of superconducting properties of Y2Pd1.25Ge2.75
PublikacjaWe report a successful synthesis of a high-purity intermetallic germanide Y2Pd1.25Ge2.75, crystallizing in the disordered variant of the AlB2-type structure. A single-phase sample was obtained via arc-melting by deliberately tuning the composition out of the ideal 2:1:3 ratio. Specific heat, electrical resistivity and magnetization measurements show that the compound is a weakly-coupled (λ e-p = 0.58) type-II superconductor with...
-
Effect of composition on the thermal properties and structure of M-Al-Si-O-N glasses, M = Na, Mg, Ca
PublikacjaThe primary objective of this study is to explore the relationship between the composition, structure, and thermal characteristics of M-Al-Si-O-N glasses, with M representing sodium (Na), magnesium (Mg), or calcium (Ca). The glasses were prepared by melting in a quartz crucible at 1650 °C and AlN precursor (powder) was utilized as a nitrogen source. The measured thermal properties studied were glass transition temperature (Tg),...
-
Effect of multi-walled carbon nanotubes properties on the photocatalytic activity of bismuth-based composites synthesised via an imidazolium ionic liquid
PublikacjaThe use of various types of multi-walled carbon nanotubes in the synthesis of bismuth oxybromide semiconductors via imidazolium ionic liquid was studied in detail. The effect of the MWCNT shape, specific surface area, and various diameters on the morphology, surface properties and photoactivity of the Bi-based composites has been investigated for the first time. So far, the literature has only shown the enhancement of photocatalytic...
-
Electrical properties of A-site Ca-doped LaNb1-xAsxO4-δ ceramics
PublikacjaThe electrical properties of A-site Ca-doped LaNbO4 with the addition of As in the B-site, have been investigated. Total, grain- and specific grain boundary electric conductivities in different oxygen partial pressure, and water vapour partial pressure were determined. Additional conductivity measurements were performed in nitrogen, to suppress the possible p-type conductivity, focusing on protonic conductivity. The maximum measured...
-
Electrochemical cobalt oxidation in chloride media
PublikacjaThe green transition, despite recent advances in cobalt-free battery technologies, is still highly dependent on the availability of critical cobalt-based materials. Consequently, there has been increasing interest towards the development of new methods that maximize critical metals recovery from industrial hydrometallurgical solutions. In the current study, direct anodic oxidation of cobalt species from cobalt chloride solutions...
-
Electrochemical detection of bacterial endotoxin lipopolysaccharide (LPS) on gold electrode modified with DAL-PEG-DK5-PEG-OH - Antimicrobial peptide conjugate
PublikacjaThis work describes fabrication of gold electrodes modified with peptide conjugate DAL-PEG-DK5-PEG-OH that enables ultra-sensitive detection of lipopolysaccharide (LPS) isolated from the reference strain of Escherichia coli O26:B6. The initial step of the established procedure implies immobilization of the fully protected DAL-PEG-DK5-PEG-OH peptide on the surface of the gold electrode previously modified by cysteamine. Then side...
-
Elucidating photoluminescent properties of Eu‐doped Ca–Al–Si–O(–N) glasses and the local structures of Eu ions
PublikacjaEuropium (Eu) ion–doped luminescent materials have attracted considerable attention for their numerous optical applications. Eu-doped Ca–Al–Si–O(–N) glasses were synthesized from a mixture of oxynitride glasses and Eu2O3 powder using a standard melt-quenching technique in a radiofrequency furnace. The source Eu trivalent ions primarily changed to Eu2+ during melting, and the ratio of Eu2+ ions increased with an increase in Eu content...
-
Encapsulation of Cs3Bi2Br9 perovskite photocatalyst with polythiophene for prolonged activity in oxidizing and humid environment
PublikacjaDespite their growing popularity in modern technology, halide perovskites suffer from susceptibility to oxidation, limiting their applications. Our aim was to enhance Cs3Bi2Br9 perovskite's performance in humid environments through polythiophene encapsulation. This extended its lifespan while preserving photocatalytic abilities, as demonstrated in toluene decomposition experiments. We confirmed the stability of Cs3Bi2Br9 encapsulated...
-
Enhanced acceptor concentration, proton conductivity, and hydration in multicomponent rare‐earth ortho‐niobates
PublikacjaThe structural properties of (La0.2Nd0.2Sm0.2Gd0.2Eu0.2)1−xCaxNbO4−δ (x = 0–0.05) series have been studied by X-ray powder diffraction at room temperature. The thermal properties were investigated using thermogravimetry, from which the concentration of proton defects was determined. Additionally, dilatometry studies were carried out, from which the thermal expansion coefficients and the phase transition temperature between low-...
-
Enhanced electrochemical activity of boron-doped nanocarbon functionalized reticulated vitreous carbon structures for water treatment applications
PublikacjaAn extraordinary charge transfer kinetics and chemical stability make a boron-doped diamond (BDD) a prom- ising material for electrochemical applications including wastewater treatment. Yet, with flat geometrical sur- faces its scaling options are limited. In this study, the reticulated Vitreous Carbon (RVC) served as a substrate for boron-doped diamondized nanocarbons (BDNC) film growth resulting with complex heterogeneity carbon structures...
-
Enhanced Electrochemical Performance of MnCo1.5Fe0.5O4Spinel for Oxygen Evolution Reaction through Heat Treatment
PublikacjaMnCo1.5Fe0.5O4 spinel oxide was synthesized using the sol−gel technique, followed by heat treatment at various temperatures (400, 600, 800, and 1000 °C). The prepared materials were examined as anode electrocatalysts for watersplitting systems in alkaline environments. Solid-state characterization methods, such as powder X-ray diffraction and X-ray absorption spectroscopy (XAS), were used to analyze the materials’ crystallographic...
-
Exploring Mechanism of Corrosion Inhibition of WE43 and AZ31 Alloys by Aqueous Molybdate in Hank’s Solution by Multisine Impedimetric Monitoring
PublikacjaThe concept of utilizing multisine dynamic electrochemical impedance spectroscopy to monitor effectiveness of a model molybdate inhibitor for AZ31 and WE43 Mg alloys is proposed. The corrosion kinetics and instantaneous values of inhibition efficiency (IE) of molybdate at concentrations up to 150 mM were examined. The inhibitor provides inhibition in Hank’s solution at concentrations starting from ca. 25 mM, with the IE of about...
-
Fabrication of high-density nitrogen-vacancy (NV) center-enriched diamond particles through methyl trityl amine (C20H19N) seeding
PublikacjaDiamond particles (DPs) show promise for advanced applications in bioimaging and quantum sensing due to the presence of defect centers. This work reports a unique growth process for diamond particles composed of nitrogen-vacancy centers (NV-DPs) using a methyl trityl amine (C20H19N) diamondoid seed, which acts as a nitrogen source for NV creation. Growth was performed via microwave plasma-assisted chemical vapor deposition in a...
-
Fine-Tuning the Photocatalytic Activity of the Anatase {1 0 1} Facet through Dopant-Controlled Reduction of the Spontaneously Present Donor State Density
PublikacjaThe present study highlights the importance of the net density of charge carriers at the ground state on photocatalytic activity of the faceted particles, which can be seen as a highly underexplored problem. To investigate it in detail, we have systematically doped {1 0 1} enclosed anatase nanoparticles with Gd3+ ions to manipulate the charge carrier concentration. Furthermore, control experiments using an analogical Nb5+ doped...
-
From phosphanylphosphaalkenes to coordination copper and silver polymers containing P–P bonds
PublikacjaThis study was focused on the activation of the C[double bond, length as m-dash]P bond via reactions of Ph2C[double bond, length as m-dash]P-PtBu2 (1) with 1,6-hexanediol and selected dithiols (1,4-butanedithiol, 1,4-benzenedithiol and 1,4-benzenedimethanethiol). These reactions proceed according to a 1,2-addition mechanism, providing new compounds with formulas {(Ph)2(H)C-P-PtBu2}{μ2-(O-(CH2)6-O)}{tBu2P-P-C(H)(Ph)2} (2), {(Ph)2(H)C-P-PtBu2}{μ2-(S-(CH2)4-S)}{tBu2P-P-C(H)(Ph)2}...
-
Green and sustainable hydrogels based on quaternized chitosan to enhance wound healing
PublikacjaHydrogel-based biomaterials applied as wound dressings provide the wound with a moist environment, which facilitates tissue regeneration through granulation and re-epithelialization. The inherent flexibility and adjustable architecture of hydrogels enables incorporation of cells, antimicrobial drugs, growth factors, and bioactive compounds, which leads to expediting wound contraction and enhancing the regeneration process. The...
-
Imidazole-Based Lithium Salt LiHDI as a Solid Electrolyte Interphase-Stabilising Additive for Lithium-Conducting Electrolytes
PublikacjaLithium salt LiHDI (lithium 4,5-dicyano-2-(n-heptafluoropropyl)imidazolide) is proposed as a solid electrolyte interphase-stabilising additive for lithium-ion batteries, which can be added in a smaller amount than fluoroethylene carbonate (FEC) and vinylene carbonate (VC) additives. Electrolytes containing either lithium 4,5-dicyano-2-(trifluoromethyl)imidazolide (LiTDI) or battery-standard LiPF6 were tested with various amounts...
-
Influence of conductive carbon and MnCo2O4 on morphological and electrical properties of hydrogels for electrochemical energy conversion
PublikacjaIn this work, a strategy for one-stage synthesis of polymer composites based on PNIPAAm hydrogel was presented. Both conductive particles in the form of conductive carbon black (cCB) and MnCo2O4 (MCO) spinel particles were suspended in the three-dimensional structure of the hydrogel. The MCO particles in the resulting hydrogel composite acted as an electrocatalyst in the oxygen evolution reaction. Morphological studies confirmed...
-
Influence of iron content on water uptake and charge transport in BaCe0.6Zr0.2Y0.2−xFexO3−δ triple-conducting oxides
PublikacjaIn this work, we studied the BaCe0.6Zr0.2Y0.2−xFexO3−δ system which belongs to the triple-conducting oxides (TCOs) group. The electrochemical properties of BaCe0.6Zr0.2Y0.2−xFexO3−δ were investigated using electrochemical impedance spectroscopy (EIS) and the water uptake was analyzed using thermogravimetry (TG). All investigated materials exhibited water uptake, with proton concentration increasing with decreasing iron content....
-
Investigating COVID-19 active pharmaceutical ingredients (APIs) degradation using Peroxydisulfate/FeMnOx binary metal oxide/Ultrasound System
PublikacjaDegradation of Favipiravir using a hybrid system of peroxydisulfate, FeMnOx binary metal oxide, and ultrasound irradiation was studied. A novel catalyst was synthesized with deep eutectic solvent (DES). The effects of DES type on catalytic performance was evaluated and the catalysts were characterized using XRD, SEM, BET, XPS, and EDS. DES-based catalysts exhibited higher efficiency due to structure change, surface area enhancement...
-
Lattice-commensurate skyrmion texture in a centrosymmetric breathing kagome magnet
PublikacjaSkyrmion lattices (SkL) in centrosymmetric materials typically have a magnetic period on the nanometer-scale, so that the coupling between magnetic superstructures and the underlying crystal lattice cannot be neglected. We reveal the commensurate locking of a SkL to the atomic lattice in Gd3Ru4Al12 via high-resolution resonant elastic x-ray scattering (REXS). Weak easy-plane magnetic anisotropy, demonstrated here by a combination...
-
Lignocellulosic waste biosorbents infused with deep eutectic solvents for biogas desulfurization
PublikacjaThis paper introduces an innovative method for treating biogas streams, employing lignocellulosic biosorbents infused with environmentally friendly solvents known as deep eutectic solvents (DES). The primary focus of this study was the elimination of volatile organosulfur compounds (VSCs) from model biogas. Biosorbents, including energetic poplar wood, antipka tree, corncobs, and beech wood, were used, each with varying levels...
-
Magnetic superhydrophobic melamine sponges for crude oil removal from water
PublikacjaThis paper proposes the preparation of a new sorbent material based on melamine sponges (MS) with superhydrophobic, superoleophilic, and magnetic properties. This study involved impregnating the surface of commercially available MS with eco-friendly deep eutectic solvents (DES) and Fe3O4 nanoparticles. The DES selection was based on the screening of 105 eutectic mixtures using COSMO-RS modeling. Other parameters affecting the efficiency...
-
Multi-Analytical Techniques for the Study of Burial Clothes of Polish King Sigismund III Vasa (1566–1633) and His Wife Constance Habsburg (1588–1631)
PublikacjaThe subjects of this research are the burial clothes of Polish King Sigismund III Vasa and his wife Constance, which were woven and embroidered with silk and metal threads. Fragments of the textiles underwent spectroscopic, spectrometric, and thermogravimetric analyses. The hydrofluoric acid extraction method was improved to isolate various classes of dyes from the textile samples that had direct contact with human remains. High-performance...
-
N-doped graphene quantum dot-decorated MOF-derived yolk-shell ZnO/NiO hybrids to boost lithium and sodium ion battery performance
PublikacjaSurface engineering at the nanoscale to obtain robust interface between metal oxides and quantum dots is essential for improving the performance and stability of battery materials. Herein, we designed and prepared novel N-doped graphene quantum dot-modified ZnO/NiO anode materials with a well-defined yolk-shell structure for lithium and sodium-ion batteries. NG QDs were assembled on the ZnO/NiO microspheres using three different...
-
New heterometallic Co/Zn, Ag/Co, and Ag/Zn imidazolates: structural characterization and catalytic activity in the oxidation of organic compounds
PublikacjaNanocrystalline powders of monometallic and bimetallic imidazolates of Co, Zn, and Ag were produced by a reaction carried out in water. The powders were characterized by powder X-ray diffraction and the crystal structures of new compounds Ag2ZnIm4 and Ag2CoIm4 (Im = imidazolate) were solved. Heterometallic Co/Zn imidazolates showed the standard ZIF-8 crystal structure while Ag/Zn and Ag/Co systems were isostructural with the copper...
-
Nitrogen-incorporated boron-doped diamond films for enhanced electrochemical supercapacitor performance
PublikacjaThe electrochemical (EC) supercapacitor, known for its rapid charging, reliability, and versatile applications, demands optimized electrode characteristics and an understanding of their electrochemical behaviour. Although boron-doped diamond (BDD) holds promise as a supercapacitor electrode, a crucial gap exists in comprehending its material behaviour under specific growth conditions. Here, nitrogen-incorporated BDD (N-BDD) films...
-
Noncentrosymmetric Triangular Magnet CaMnTeO6: Strong Quantum Fluctuations and Role of s0 versus s2 Electronic States in Competing Exchange Interactions
PublikacjaNoncentrosymmetric triangular magnets offer a unique platform for realizing strong quantum fluctuations. However, designing these quantum materials remains an open challenge attributable to a knowledge gap in the tunability of competing exchange interactions at the atomic level. Here, a new noncentrosymmetric triangular S = 3/2 magnet CaMnTeO6 is created based on careful chemical and physical considerations. The model material...
-
Organic pollutants photodegradation increment with use of TiO2 nanotubes decorated with transition metals after pulsed laser treatment
PublikacjaAmong various titanium(IV) oxide (TiO2, titania) structures, 1D nanotubes (TiO2 NTs) produced during the two-electrode anodization process, are extensively utilized in sensors or supercapacitors as well as in photo(electro)catalytic water splitting. However, due to wide bandgap and fast electron-hole recombination additional modifications, mostly concerned on materials surface, are required. According to the recent research, TiO2...
-
Phospholipid-functionalized gold electrode for cellular membrane interface studies - interactions between DMPC bilayer and human cystatin C
PublikacjaThis work describes the electrochemical studies on the interactions between V57G mutant of human cystatin C (hCC V57G) and membrane bilayer immobilized on the surface of a gold electrode. The electrode was modified with 6-mercaptohexan-1-ol (MCH) and 1,2-dimyristoyl-sn-glycero-3-phosphocholine (DMPC). DMPC was used as a membrane mimetic for monitoring electrochemical changes resulting from the interactions between the functionalized...
-
Progress in ATRP-derived materials for biomedical applications
PublikacjaThe continuing wave of technological breakthroughs and advances is critical for engineering well- defined materials, particularly biomaterials, with tailored microstructure and properties. Over the last few decades, controlled radical polymerization (CRP) has become a very promising option for the synthesis of precise polymeric materials with an unprecedented degree of control over mo lecular architecture. Atom transfer radical...
-
Quasi-one-dimensional exchange interactions and short-range magnetic correlations in CuTeO4
PublikacjaCuTeO4 has been proposed as a crystallographically distinct, yet electronic structure analog, of the superconducting cuprates. Here, we present a detailed characterization of the physical properties of CuTeO4 to address this proposal. Fitting of magnetic susceptibility data indicates unexpected quasi-one-dimensional, antiferromagnetic correlations at high temperature, with a nearest-neighbor Heisenberg exchange of 1=164(5) K....
-
Recycled rubber wastes-based polymer composites with flame retardancy and electrical conductivity: Rational design, modeling and optimization
PublikacjaPolymer recycling techniques experience a maturity period of design and application. Rubbers comprise a high proportion of polymer wastes, highly flammable and impossible to re-melt. Polymer composites based on ground tire rubber (GTR) and ethylene-vinyl acetate copolymer (EVA) containing carbon black (CB) (1–50 phr), with variable EVA/GTR weight composition (10/90, 25/75, 50/50, 75/25 and 90/10), and processing temperature (Low:...
-
Structural phase transitions in multicomponent La0.2Nd0.2Sm0.2Gd0.2RE50.2NbO4 (RE5 = Ho, Y, Tb, Eu, Pr) oxides
PublikacjaIn this work, the influence of compositional complexity on the structural and thermal properties of multicomponent rare-earth ortho-niobates from the La0.2Nd0.2Sm0.2Gd0.2RE50.2NbO4 (RE5 = Ho, Y, Tb, Eu, Pr) series have been investigated. Based on X-ray powder diffraction studies using synchrotron radiation, it was found that all tested materials were pure single-phase compositions and showed stability in the monoclinic I2/c crystal...
-
Superconductivity–Electron Count Relationship in Heusler Phases─the Case of LiPd2Si
PublikacjaWe report superconductivity in the full Heusler compound LiPd2Si (space group Fm3̅m, No. 225) at a critical temperature of Tc = 1.3 K and a normalized heat capacity jump at Tc, ΔC/γTc = 1.1. The low-temperature isothermal magnetization curves imply type-I superconductivity, as previously observed in LiPd2Ge. We show, based on density functional theory calculations and using the molecular orbital theory approach, that while LiPd2Si...
-
Tailoring Defects in B, N-Codoped Carbon Nanowalls for Direct Electrochemical Oxidation of Glyphosate and its Metabolites
PublikacjaTailoring the defects in graphene and its related carbon allotropes has great potential to exploit their enhanced electrochemical properties for energy applications, environmental remediation, and sensing. Vertical graphene, also known as carbon nanowalls (CNWs), exhibits a large surface area, enhanced charge transfer capability, and high defect density, making it suitable for a wide range of emerging applications. However, precise...
-
Tunable emission and energy transfer of B2O3–Bi2O3–AlF3 glass system doped with Eu3+/Dy3+
PublikacjaThe structure and luminescent properties of the B2O3–Bi2O–AlF3 glass system doped with Eu3+/Dy3+ ions in different molar ratios were studied. A series of glasses were synthesized by the conventional melt quenching technique. Glass transition and crystallization temperatures were examined by Differential Thermal Analysis (DTA) measurements. The amorphous character of the prepared samples was confirmed by the X-ray diffraction (XRD)...
-
Tuning the work function of graphite nanoparticles via edge termination
PublikacjaGraphite nanoparticles are important in energy materials applications such as lithium-ion batteries (LIBs), supercapacitors and as catalyst supports. Tuning the work function of the nanoparticles allows local control of lithiation behaviour in LIBs, and the potential of zero charge of electrocatalysts and supercapacitors. Using large scale density functional theory (DFT) calculations, we find that the surface termination of multilayer...
-
Ultrafast high-temperature sintering (UHS) of cerium oxide-based compound
PublikacjaUltrafast high-temperature sintering (UHS) is an innovative sintering technique that can densify ceramics in a few seconds, dramatically reducing the carbon footprint and firing costs. In this work, the feasibility of applying UHS in Gd-doped ceria (GDC) and GDC-Er-stabilized bismuth oxide (ESB) composite powders was investigated. At high UHS currents (22-24 A), a fully dense GDC sample with a large grain size was obtained. Nonetheless,...
Rok 2023
-
An adaptive approach to non-destructive evaluation (NDE) of cast irons containing precipitated graphite particles with the help of magnetoacoustic emission
PublikacjaPhysical properties of cast irons strongly depend on both their microstructure and the presence of casting defects. The paper analyses the possibility of application of magnetoacoustic emission (MAE) for nondestructive detection of flawed cast iron components. The investigated samples containing dross, chunky graphite and lamellar graphite were compared with the reference, flawless, spheroidal cast iron sample. The optimisation...
-
Annealing Rate as a Crucial Parameter Controlling the Photoelectrochemical Properties of AuCu Mosaic Core–Shell Nanoparticles
PublikacjaThermal processing is an essential step during the synthesis of various metal nanostructures and for tailoring their morphology, optical, and electrochemical properties. Herein, a profound impact of the annealing rate and time on photoactivity of gold–copper nanostructures by changes in the position and alignment of energy levels and surface states is reported. AuCu nanoparticles (NPs) are fabricated by sputtering of thin metal...
-
Band Gap Engineering toward Semimetallic Character of Quinone-Rich Polydopamine
PublikacjaSemiconductor|melanin interfaces have received increasingly more attention in the fields of photocatalysis and applied electrochemistry because of their facile synthesis, unique electrical properties, and strong capability toward photosensitization. In this work, we describe the electropolymerization of quinone-rich polydopamine (PDA) on the surface of hydrogenated TiO2 nanotubes with enhanced photoactivity in the visible spectrum....
-
Bi-based halide perovskites: Stability and opportunities in the photocatalytic approach for hydrogen evolution
PublikacjaIn this study, we successfully prepared Bi-based single perovskites of the A3Bi2I9 type (A = Cs, Rb, MA, FA), and, for the first time, attempted to experimentally obtain double perovskites Cs2B’BiI6 type (B′ = Ag, Au, In, Cu). Despite the premises available in theoretical studies, our research has proven the impossibility of the existence of double perovskites of this type. Nevertheless, both types of obtained materials were subjected...
-
Boron-doped diamond nanosheet volume-enriched screen-printed carbon electrodes: a platform for electroanalytical and impedimetric biosensor applications
PublikacjaThis paper focuses on the development of a novel electrode based on boron-doped diamond nanosheet full-volume-enriched screen-printed carbon electrodes (BDDPE) for use as an impedimetric biosensor. Impedimetric biosensors offer high sensitivity and selectivity for virus detection, but their use as point-of-care devices is limited by the complexity of nanomaterials’ architecture and the receptor immobilisation procedures. The study...
-
Bovine Serum Albumin – Hydroxyapatite Nanoflowers as Potential Local Drug Delivery System of Ciprofloxacin
PublikacjaIntroduction: Hybrid nanoflowers are structures consisting of organic (enzymes, proteins, nucleic acids) and inorganic components (mostly metal phosphates) with a flower-like hierarchical structure. Novel hybrid nanoflowers based on bovine serum albumin (BSA) and hydroxyapatite (HA) were obtained and characterized. Study on BSA-HA nanoflowers as potential drug delivery system is reported for the first time. Methods: Embedding ciprofloxacin...